[why]
- Adding a DM interface to enable DSC over eDP on Linux
- DSC over eDP will allow to power savings by reducing
the bandwidth required to support panel's modes
- Apply link optimization algorithm to reduce link bandwidth
when DSC is enabled
[how]
- Read eDP panel's DSC capabilities
- Apply DSC policy on eDP panel based on its DSC capabilities
- Enable DSC encoder's on the pipe
- Enable DSC on panel's side by setting DSC_ENABLE DPCD register
- Adding link optimization algorithm to reduce link rate or lane
count based
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DC we want to wait for the INBOX0 HW Lock command to ACK before
continuing. This is to ensure that the lock has been successfully
acquired before programming HW in DC.
[How]
Add interfaces to send messages on INBOX0, poll for their completation
and clear the ack.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some panels require to use TPS3 pattern to wake up link in PSR mode.
[How]
To add TPS3 selection information in PSR settings command and pass to
DMUB FW.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Robin Chen <po-tchen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
reduce az indirect register dump. need add az clock_gating control field
used in some project.
[how]
conditional output indrect register in the log. add clock_gating feild
Reviewed-by: Sung joon Kim <Sungjoon.Kim@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
PSR set power command wasn't setting panel instance
and command version which caused both streams
to overwrite the same PSR state.
[how]
Pass panel instance to the set power command function
and to DMUB and set command version enum
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPO is only used for DP2.0. HPO HW control should be
disable when not being used to save power.
[How]
Shutdown HPO HW control during init hw.
Shutdown HPO HW control during stream disable.
Enable HPO HW control during stream enable if DP2.0.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Why:
For audio packet type 0x02, there are 2 Layouts:
Layout = 0 for 2 channels
and Layout = 1 for > 2 channels.
Layout will affect bandwidth check.
Currently, for HDMI FRL, Layout field isn't set and has a default value
of 0, so theoretically only 2-channel audio for audio packet type 0x02
is supported now.
How:
1. Set Layout properly according to maximum audio channel numbers for
audios with audio packet type 0x02.
2. 8ch LPCM audio is not supported for timing modes with v_active <= 576.
Reviewed-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Bing Guo <Bing.Guo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When writing long AUX commands some sinks will respond will write status
update requiring source to read status.
[How]
When a write request is replied with data (AUX_ACK_M), retry a read of
write status to determine when the write is completed.
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
i2c memory doesn't get set to light sleep on hw init as intended
[HOW]
Set i2c to light sleep after reg gets zeroed, ensuring memory power
control doesn't get disabled for any other DIO memory
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To expose new power optimization flags to PSR interface. It allows the
PSR related power features can be enabled separately base on different
use scenarios.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Robin Chen <po-tchen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
PSR_STATE2b was introduced on DMCUB side, but not on the driver side,
which caused convert_psr_state helper function to return
PSR_STATE_INVALID. That caused visual lagging during state transition.
[how]
Add PSR_STATE2b to dc_psr_state and convert_psr_state
Reviewed-by: Wyatt Wood <Wyatt.Wood@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
1. Remove unnecessary dummy interrupt source for USB4 HPD & HPD RX
2. Adjust parameter for DPCD writing of link training process of DPIA link
3. Adjust specific AUX defer delay for DPIA link
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
add display related cyan_skillfish files in.
makefile controlled by CONFIG_DRM_AMD_DC_DCN201 flag.
v2: squash in clang fixes from Harry, Nathan
v3: squash in missing CONFIG_DRM_AMD_DC check (Alex)
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Jun Lei <jun.lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To prevent unnecessary wake up of DMCUB when ABM is enabled without PSR
enabled, driver will notify DMCUB to stop ABM's vertical interrupts
if vsync is disabled and steady state is reached.
[How]
Send inbox message to notify ABM pause based on vsync on/off
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Using an empty macro expansion as a conditional expression
produces a W=1 warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c: In function 'dce_aux_transfer_with_retries':
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c:775:156: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
775 | "dce_aux_transfer_with_retries: AUX_RET_SUCCESS: AUX_TRANSACTION_REPLY_I2C_OVER_AUX_DEFER");
| ^
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c:783:155: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
783 | "dce_aux_transfer_with_retries: AUX_RET_SUCCESS: AUX_TRANSACTION_REPLY_I2C_OVER_AUX_NACK");
| ^
Expand it to "do { } while (0)" instead to make the expression
more robust and avoid the warning.
Fixes: 56aca23093 ("drm/amd/display: Add AUX I2C tracing.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On Carrizo/Stoney systems we set backlight through panel_cntl, i.e.
directly via the PWM registers, if DMCU is not initialized. We
always read it back through ABM registers which leads to a
mismatch and forces atomic_commit to program the backlight
each time.
Instead make sure we use the same logic for backlight readback,
i.e. read it from panel_cntl if DMCU is not initialized.
We also need to remove some extraneous and incorrect calculations
at the end of dce_get_16_bit_backlight_from_pwm.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1666
Cc: stable@vger.kernel.org
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need a check for NULL pointer access for ddc pin and aux engine.
[How]
Adding a check for ddc pin and aux engine accesses.
Reviewed-by: Jimmy Kizito <jimmy.kizito@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit "Revert "Add DPCD writes at key points" ".
The following patch will fix the system hang issue.
v2: squash in indentation warning fix
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some ABM registers don't exist on DCN 3.01, so are
missing from its register offset list. However,
this list was copied to later versions of DCN that
do have these registers. As a result, they're
inaccessible from the driver on those DCN versions
even though they exist.
[How]
Add the missing ABM register offsets to DCN 3.02+
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Building with W=1 complains about an empty 'else' statement, so use the
usual do-nothing-while-0 loop to quieten this warning.
../drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:113:53: warning: suggest braces around empty body in an 'else' statement [-Wempty-body]
113 | *state, retry_count);
Fixes: b30eda8d41 ("drm/amd/display: Add ETW log to dmub_psr_get_state")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Wyatt Wood <wyatt.wood@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Developers can find it useful if the driver can produce
AUX traces without special equipment.
[How]
Add AUX tracing.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
GPINT commands have the lowest priority in DMCUB, so it's possible
that the command isn't processed in time.
[How]
Add a log to help identify this case.
Reviewed-by: Koo Anthony <Anthony.Koo@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Would like to identify the cause of AUX transactions failing
via ETW logs.
[How]
Add ETW logging for AUX failures.
Reviewed-by: Pavic Josip <Josip.Pavic@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
For dual eDP when setting the new settings we need to set
command version to DMUB_CMD_PSR_CONTROL_VERSION_1, otherwise
DMUB will not read panel_inst parameter.
[how]
Instead of PSR_VERSION_1 pass DMUB_CMD_PSR_CONTROL_VERSION_1
Reviewed-by: Wood Wyatt <Wyatt.Wood@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During S4/S5/reboot, sometimes riommu invalidation request arrive too
early, DCN may be unable to respond to the invalidation request
resulting in pstate hang.
[How]
VBIOS will force allow pstate for riommu invalidation and driver will
clear it after powering down display pipes.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need for a separate flag now that DCN3.1 is not in bring up.
Fold into DRM_AMD_DC_DCN like previous DCN IPs.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
recent VBIOS dce_infotable reference clock change caused a I2c regression.
instead of relying on vbios, let's get it from HW directly.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix
the following warning by replacing a /* fall through */ comment
with the new pseudo-keyword macro fallthrough:
rivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c:672:4: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]
case AUX_TRANSACTION_REPLY_I2C_OVER_AUX_DEFER:
^
Notice that Clang doesn't recognize /* fall through */ comments as
implicit fall-through markings, so in order to globally enable
-Wimplicit-fallthrough for Clang, these comments need to be
replaced with fallthrough; in the whole codebase.
Link: https://github.com/KSPP/linux/issues/115
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DP 2.0 SCR specifies that
"A DPTX shall distinguish I2C_DEFER|AUX_ACK from AUX_DEFER. AUX retries
due to
I2C_DEFER are not counted as part of minimum 7 retires (sic) upon
AUX_DEFER’s"
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DP 2.0 SCR specifies that TX devices must retry at least 7 times when
receiving an AUX DEFER reply from RX. In addition, the specification
states that the TX shall not retry indefinitely, and gives a suggestive
timeout interval of 50ms.
[HOW]
Keep retrying until both 7 or more retries have been made, and the 50ms
interval has passed.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
7 is the minimum number of retries TX must attempt on an AUX DEFER, not
the maximum.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Allow specifying which panel to take PSR Residency
measurements from.
[how]
Pass panel instance to DMUB through GPINT in the upper
8 bits of the parameter.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Updating PSR interfaces to allow PSR enablement
per eDP panel.
[how]
- Copying PSR command structures to DC
- Changing function interfaces to pass panel instance
- Communicating with DMUB per link instead of assuming
to use a single one
-Iterating through all PSR capable panels when enabling/disabling
all
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add DCN3.1 specific hardware sequence programming - extending off of
our existing DCN3/DCN2 support.
Extend stream hardware sequencing to include new DCCG programming.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is needed to avoid warnings with linebuffer depth 36 bpp.
Testing on a Polaris11, DCE-11.2 on a 10 bit HDR-10 monitor
showed no obvious problems, and this 12 bpc limit is consistent
with what other function in the DCE bit depth reduction path use.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Testing with the photometer shows that at least Raven Ridge DCN-1.0
does not achieve more than 10 bpc effective output precision with a
16 bpc unorm surface of type SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616,
unless linebuffer depth is increased from LB_PIXEL_DEPTH_30BPP to
LB_PIXEL_DEPTH_36BPP. Otherwise precision gets truncated somewhere
to 10 bpc effective depth.
Strangely this increase was not needed on Polaris11 DCE-11.2 during
testing to get 12 bpc effective precision. It also is not needed for
fp16 framebuffers.
Tested on DCN-1.0 and DCE-11.2.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the necessary format definition, bandwidth and pixel size mappings,
prescaler setup, and pixelformat selection, following the logic
already present for SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616.
The new SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616 is implemented as the
old SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616 format, but with swapped
red <-> green color channel, by use of the hardware xbar.
Please note that on the DCN 1/2/3 display engines, the pixelformat
in hubp and dpp setup for the old SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616
and the new SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616 was changed from
format id 22 to id 26. See amd/include/navi10_enum.h for the meaning
of the id's.
For format 22, the display engine read the framebuffer in 16 bpc format,
but truncated to the 12 bpc actually supported by later pipeline stages.
However, the engine took the 12 LSB of each color component for
truncation, which is incompatible with rendering at least under Vulkan,
where content is 16 bit wide, and a 12 MSB alignment would be appropriate,
if any. Format 20 for ARGB16161616_12MSB does work, but even better, we
can choose format 26 for ARGB16161616_UNORM, keeping all 16 bits around
until later stages of the display pipeline.
This allows to directly consume what the rendering hw produces under
Vulkan for swapchain format VK_FORMAT_R16G16B16A16_UNORM, as tested
with a patched version of the current AMD open-source amdvlk driver
which maps swapchain format VK_FORMAT_R16G16B16A16_UNORM onto
DRM_FORMAT_XBGR16161616.
The old id 22 would cause colorful pixeltrash to be displayed instead.
Tested under DCN-1.0 and DCE-11.2.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:29:
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_sh_mask.h:7270:45: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:159:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:264:2: note: in expansion of macro ‘MI_GFX6_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:657:3: note: in expansion of macro ‘MI_DCE6_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_sh_mask.h:7270:45: note: (near initialization for ‘mi_shifts.GRPH_NUM_BANKS’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:159:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:264:2: note: in expansion of macro ‘MI_GFX6_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:657:3: note: in expansion of macro ‘MI_DCE6_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_sh_mask.h:7269:43: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:159:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:264:2: note: in expansion of macro ‘MI_GFX6_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:662:3: note: in expansion of macro ‘MI_DCE6_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_sh_mask.h:7269:43: note: (near initialization for ‘mi_masks.GRPH_NUM_BANKS’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:159:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:264:2: note: in expansion of macro ‘MI_GFX6_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:662:3: note: in expansion of macro ‘MI_DCE6_MASK_SH_LIST’
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:29:
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_sh_mask.h:7270:45: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:159:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:265:2: note: in expansion of macro ‘MI_GFX6_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:657:3: note: in expansion of macro ‘MI_DCE6_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_sh_mask.h:7270:45: note: (near initialization for ‘mi_shifts.GRPH_NUM_BANKS’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:159:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:265:2: note: in expansion of macro ‘MI_GFX6_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:657:3: note: in expansion of macro ‘MI_DCE6_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_sh_mask.h:7269:43: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:159:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:265:2: note: in expansion of macro ‘MI_GFX6_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:662:3: note: in expansion of macro ‘MI_DCE6_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_sh_mask.h:7269:43: note: (near initialization for ‘mi_masks.GRPH_NUM_BANKS’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:159:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:265:2: note: in expansion of macro ‘MI_GFX6_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:662:3: note: in expansion of macro ‘MI_DCE6_MASK_SH_LIST’
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_outbox.c:30: warning: Cannot understand *****************************************************************************
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Cc: Jun Lei <Jun.Lei@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Start using INBOX0 for HW Lock command
[How]
- Implement initial interface for INBOX0 HW lock message
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Added support for individual control for multiple back-light instances.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To process AUX transactions with DMUB using inbox1 and outbox1 mail boxes.
[How]
1) Added inbox1 command DMUB_CMD__DP_AUX_ACCESS to issue AUX commands
to DMUB in dc_process_dmub_aux_transfer_async(). DMUB processes AUX cmd
with DCN and sends reply back in an outbox1 message triggering an
outbox1 interrupt to driver.
2) In existing driver implementation, AUX commands are processed
synchronously by configuring DCN reg. But in DMUB AUX, driver sends an
inbox1 message and waits for a conditional variable (CV) which will be
signaled by outbox1 ISR.
3) DM will retrieve Outbox1 message and send back reply to upper layer
and complete the AUX command
Signed-off-by: Jude Shih <shenshih@amd.com>
Reviewed-by: Hanghong Ma <Hanghong.Ma@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
ABM assumes only 1 eDP is connected. Refactored existing
ABM interface to support multiple instances.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DSC is enabled before reset link and potentially cause DSC enable fail problem.
[How]
Enable DSC after link is reseted
Signed-off-by: Mike Hsieh <chun-wei.hsieh@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
GPINT command to get PSR state from FW times out.
[How]
Add retry to get valid PSR state.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Replace GFP_KERNEL with GFP_ATOMIC as dcn20_resource_construct()
can't sleep.
Partially fixes: https://bugzilla.kernel.org/show_bug.cgi?id=212311
as dcn20_resource_construct() also calls into SMU functions which does
mutex_lock().
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
