PCIe fails to link up if SERDES lanes not used by PCIe are assigned to
another protocol. For example, link training fails if lanes 2 and 3 are
assigned to another protocol while lanes 0 and 1 are used for PCIe to
form a two lane link. This failure is due to an incorrect tie-off on an
internal status signal indicating electrical idle.
Status signals going from SERDES to PCIe Controller are tied-off when a
lane is not assigned to PCIe. Signal indicating electrical idle is
incorrectly tied-off to a state that indicates non-idle. As a result,
PCIe sees unused lanes to be out of electrical idle and this causes
LTSSM to exit Detect.Quiet state without waiting for 12ms timeout to
occur. If a receiver is not detected on the first receiver detection
attempt in Detect.Active state, LTSSM goes back to Detect.Quiet and
again moves forward to Detect.Active state without waiting for 12ms as
required by PCIe base specification. Since wait time in Detect.Quiet is
skipped, multiple receiver detect operations are performed back-to-back
without allowing time for capacitance on the transmit lines to
discharge. This causes subsequent receiver detection to always fail even
if a receiver gets connected eventually.
Add a quirk flag "quirk_detect_quiet_flag" to program the minimum
time the LTSSM should wait on entering Detect.Quiet state here.
This has to be set for J7200 as it has an incorrect tie-off on unused
lanes.
Link: https://lore.kernel.org/r/20210811123336.31357-3-kishon@ti.com
Signed-off-by: Nadeem Athani <nadeem@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Now that support for SR-IOV is added in PCIe endpoint core, add support
to configure virtual functions in the Cadence PCIe EP driver.
Link: https://lore.kernel.org/r/20210819123343.1951-7-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
No functional change. Simplify code to get register base address for
configuring PCI BAR.
Link: https://lore.kernel.org/r/20210819123343.1951-6-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add virtual function number in pci_epc ops. EPC controller driver
can perform virtual function specific initialization based on the
virtual function number.
Link: https://lore.kernel.org/r/20210819123343.1951-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
When the link is in L1, hardware should return it to L0
automatically whenever a transaction targets a component on the
other end of the link (PCIe r5.0, sec 5.2).
The R-Car PCIe controller doesn't handle this transition correctly.
If the link is not in L0, an MMIO transaction targeting a downstream
device fails, and the controller reports an ARM imprecise external
abort.
Work around this by hooking the abort handler so the driver can
detect this situation and help the hardware complete the link state
transition.
When the R-Car controller receives a PM_ENTER_L1 DLLP from the
downstream component, it sets PMEL1RX bit in PMSR register, but then
the controller enters some sort of in-between state. A subsequent
MMIO transaction will fail, resulting in the external abort. The
abort handler detects this condition and completes the link state
transition by setting the L1IATN bit in PMCTLR and waiting for the
link state transition to complete.
Link: https://lore.kernel.org/r/20210815181650.132579-1-marek.vasut@gmail.com
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
Hyper-V vPCI protocol version 1_4 adds support for create interrupt
v3. Create interrupt v3 essentially makes the size of the vector
field bigger in the message, thereby allowing bigger vector values.
For example, that will come into play for supporting LPI vectors
on ARM, which start at 8192.
Link: https://lore.kernel.org/r/MW4PR21MB20026A6EA554A0B9EC696AA8C0159@MW4PR21MB2002.namprd21.prod.outlook.com
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Enable PCIe reference clock. There is no remove function that's why
this should be enough for simple operation.
Normally this clock is enabled by default by firmware but there are
usecases where this clock should be enabled by driver itself.
It is also good that PCIe clock is recorded in a clock framework.
Link: https://lore.kernel.org/r/ee6997a08fab582b1c6de05f8be184f3fe8d5357.1624618100.git.michal.simek@xilinx.com
Fixes: ab597d35ef ("PCI: xilinx-nwl: Add support for Xilinx NWL PCIe Host Controller")
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
When both the old and the new PCI drivers are enabled
in the same kernel, there are a couple of namespace
conflicts that cause a build failure:
drivers/pci/controller/pci-ixp4xx.c:38: error: "IXP4XX_PCI_CSR" redefined [-Werror]
38 | #define IXP4XX_PCI_CSR 0x1c
|
In file included from arch/arm/mach-ixp4xx/include/mach/hardware.h:23,
from arch/arm/mach-ixp4xx/include/mach/io.h:15,
from arch/arm/include/asm/io.h:198,
from include/linux/io.h:13,
from drivers/pci/controller/pci-ixp4xx.c:20:
arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h:221: note: this is the location of the previous definition
221 | #define IXP4XX_PCI_CSR(x) ((volatile u32 *)(IXP4XX_PCI_CFG_BASE_VIRT+(x)))
|
drivers/pci/controller/pci-ixp4xx.c:148:12: error: 'ixp4xx_pci_read' redeclared as different kind of symbol
148 | static int ixp4xx_pci_read(struct ixp4xx_pci *p, u32 addr, u32 cmd, u32 *data)
| ^~~~~~~~~~~~~~~
Rename both the ixp4xx_pci_read/ixp4xx_pci_write functions and the
IXP4XX_PCI_CSR macro. In each case, I went with the version that
has fewer callers to keep the change small.
Fixes: f7821b4934 ("PCI: ixp4xx: Add a new driver for IXP4xx")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: soc@kernel.org
Link: https://lore.kernel.org/r/20210721151546.2325937-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
pm_runtime_get_sync() will increase the runtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.
Link: https://lore.kernel.org/r/20210408072402.15069-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
devm_ioremap_resource() internally calls __devm_ioremap_resource() which
is where error checking and handling is actually taking place. i
Therefore, the dev_err() call in xgene_msi_probe() is redundant.
Remove it.
Link: https://lore.kernel.org/r/20210408132751.1198171-1-yangerkun@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: ErKun Yang <yangerkun@huawei.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Don't populate the array err_msg on the stack but instead make it
static. Makes the object code smaller by 64 bytes.
While at it, add a missing const, as reported by checkpatch.
Compiled with gcc 11.0.1
Before:
$ size drivers/pci/controller/pci-tegra.o
text data bss dec hex filename
25623 2844 32 28499 6f53 drivers/pci/controller/pci-tegra.o
After:
$ size drivers/pci/controller/pci-tegra.o
text data bss dec hex filename
25559 2844 32 28435 6f13 drivers/pci/controller/pci-tegra.o
Link: https://lore.kernel.org/r/5f3f35296b944b94546cc7d1e9cc6186484620d8.1620148539.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Commit 9e38e690ac ("PCI: tegra: Fix OF node reference leak") has fixed
some node reference leaks in this function but missed some of them.
In fact, having 'port' referenced in the 'rp' structure is not enough to
prevent the leak, until 'rp' is actually added in the 'pcie->ports' list.
Add the missing 'goto err_node_put' accordingly.
Link: https://lore.kernel.org/r/55b11e9a7fa2987fbc0869d68ae59888954d65e2.1620148539.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Set CRSVIS flag in emulated root PCI bridge to indicate support for
Completion Retry Status.
Add check for CRSSVE flag from root PCI brige when issuing Configuration
Read Request via PIO to correctly returns fabricated CRS value as it is
required by PCIe spec.
Link: https://lore.kernel.org/r/20210722144041.12661-5-pali@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # e0d9d30b73 ("PCI: pci-bridge-emul: Fix big-endian support")
Measurements in different conditions showed that aardvark hardware PIO
response can take up to 1.44s. Increase wait timeout from 1ms to 1.5s to
ensure that we do not miss responses from hardware. After 1.44s hardware
returns errors (e.g. Completer abort).
The previous two patches fixed checking for PIO status, so now we can use
it to also catch errors which are reported by hardware after 1.44s.
After applying this patch, kernel can detect and print PIO errors to dmesg:
[ 6.879999] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100004
[ 6.896436] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100004
[ 6.913049] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100010
[ 6.929663] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100010
[ 6.953558] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100014
[ 6.970170] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100014
[ 6.994328] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100004
Without this patch kernel prints only a generic error to dmesg:
[ 5.246847] advk-pcie d0070000.pcie: config read/write timed out
Link: https://lore.kernel.org/r/20210722144041.12661-3-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # 7fbcb5da81 ("PCI: aardvark: Don't rely on jiffies while holding spinlock")
There is an issue that when PCIe switch is connected to an Armada 3700
board, there will be lots of warnings about PIO errors when reading the
config space. According to Aardvark PIO read and write sequence in HW
specification, the current way to check PIO status has the following
issues:
1) For PIO read operation, it reports the error message, which should be
avoided according to HW specification.
2) For PIO read and write operations, it only checks PIO operation complete
status, which is not enough, and error status should also be checked.
This patch aligns the code with Aardvark PIO read and write sequence in HW
specification on PIO status check and fix the warnings when reading config
space.
[pali: Fix CRS handling when CRSSVE is not enabled]
Link: https://lore.kernel.org/r/20210722144041.12661-2-pali@kernel.org
Tested-by: Victor Gu <xigu@marvell.com>
Signed-off-by: Evan Wang <xswang@marvell.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # b1bd571447 ("PCI: aardvark: Indicate error in 'val' when config read fails")
When Tegra PCIe is in endpoint mode it should be available for root port.
PCIe link up by root port fails if it is in suspend state. So, don't allow
Tegra to suspend when endpoint mode is enabled.
Link: https://lore.kernel.org/r/20210623100525.19944-5-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
In suspend_noirq() call if link doesn't goto L2, PERST# is asserted
to bring link to detect state. However, this is causing surprise
link down AER error. Since Kernel is executing noirq suspend calls,
AER interrupt is not processed. PME and AER are shared interrupts
and PCIe subsystem driver enables wake capability of PME irq during
suspend. So this AER will cause suspend failure due to pending
AER interrupt.
After PCIe link is in L2, interrupts are not expected since PCIe
controller will be in reset state. Disable PCIe interrupts before
going to L2 state to avoid pending AER interrupt.
Link: https://lore.kernel.org/r/20210623100525.19944-4-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
Lower order MSI-X address is programmed in MSIX_ADDR_MATCH_HIGH_OFF
DBI register instead of higher order address. This patch fixes this
programming mistake.
Link: https://lore.kernel.org/r/20210623100525.19944-3-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
In tegra_pcie_ep_hard_irq(), APPL_INTR_STATUS_L0 is stored in val and again
APPL_INTR_STATUS_L1_0_0 is also stored in val. So when execution reaches
"if (val & APPL_INTR_STATUS_L0_PCI_CMD_EN_INT)", val is not correct.
Link: https://lore.kernel.org/r/20210623100525.19944-2-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
In commit 7ef1c871da ("PCI: iproc: Use
pci_parse_request_of_pci_ranges()"), calling
devm_request_pci_bus_resources() was dropped from the common iProc
probe code, but is still needed for BCMA bus probing. Without it, there
will be lots of warnings like this:
pci 0000:00:00.0: BAR 8: no space for [mem size 0x00c00000]
pci 0000:00:00.0: BAR 8: failed to assign [mem size 0x00c00000]
Add back calling devm_request_pci_bus_resources() and adding the
resources to pci_host_bridge.windows for BCMA bus probe.
Link: https://lore.kernel.org/r/20210803215656.3803204-2-robh@kernel.org
Fixes: 7ef1c871da ("PCI: iproc: Use pci_parse_request_of_pci_ranges()")
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
Cc: Roman Bacik <roman.bacik@broadcom.com>
Cc: Bharat Gooty <bharat.gooty@broadcom.com>
Cc: Abhishek Shah <abhishek.shah@broadcom.com>
Cc: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Cc: Ray Jui <ray.jui@broadcom.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: BCM Kernel Feedback <bcm-kernel-feedback-list@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: "Krzysztof Wilczyński" <kw@linux.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Link: https://lore.kernel.org/r/20210802162630.2219813-4-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Following the code refactoring completed in the commit 1fd92928ba
("PCI: tegra: Refactor configuration space mapping code") there are no
more known users of struct tegra_pcie_bus.
Thus, remove declaration of struct tegra_pcie_bus as it's no longer
needed and does not have any existing users left.
Link: https://lore.kernel.org/r/20210704235733.2514131-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The Intel IXP4xx PCI controller is only present on Intel IXP4xx
XScale-based network processor SoCs.
Add a dependency on ARCH_IXP4XX, to prevent asking the user about this
driver when configuring a kernel without support for the XScale
processor family.
Link: https://lore.kernel.org/r/6a88e55fe58fc280f4ff1ca83c154e4895b6dcbf.1624972789.git.geert+renesas@glider.be
Fixes: f7821b4934 ("PCI: ixp4xx: Add a new driver for IXP4xx")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the end
of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing legacy
mach/* include dependencies and moving platform detection/config to
drivers/soc. Also some updates/cleanup of platform data.
- Core power domain support for Tegra platforms, and some improvements
in build test coverage by adding stubs for compile test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI) SMP
support on i.MX7D, SoC ID setup for i.MX50, removal of platform data
and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCgAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAmDojiQPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3Z+kQAJofM2XXE3eHoIGINp+XuYZHCAdTxpIJfhsQ
KPt4dzaxq0eBhrD8PICelJ2ymWz4c3sO2z+v79zQfOJdutnFKWTCRstqW8qdq9cE
vzYh5pDJy0VmLkYSX/PzvfTLUQDM+Cx0sH/8e2gRwCC/F5tXolLA8lcqWQg9LnlC
5joLOm2WL2uHDgPFZLR6Y1m0KabvUMMpYx6ji9EUx4qtc0VgRMRTSZkRZK4E1PU+
ls175pPZxQfmTyFuHGc1L6KrfnHry8+YX/61sMlBfi96itMnBi05PcxljH8hMkQ8
IVfqPYVnI2vX37f8MhcX4Wec8pKQ9SZqT9mbADGEG23XfZppT5cp7pJUACoZ/wJ5
MMXn99hsEI0NO/gswKr2ZCCskydWrwOqhzubxZrYQtyFt38Sgs+mMLYxyQJKztbZ
Laz+JBYKsvIlRctt+fArLp79EJx+CpSUpcha5Q0dQUmz3GWApPpS/6nMiNkq1Myv
aByG9HXjOpRI5IiaOi7Fv/m/i+TsO43boNFerUIqPYi2AxmM9D8M2sJcyWHVwQRK
glSAjISbp0GHAzVPM5JzhGIrCu4xC5Hf09Q+0OP6c3YVylwKNMurJCjCCql+ft8I
Z41WVglS4xO5Y/qiWi+5pzg7/+VESBcsFn6PA5AJAAsDGgU5WHHXhI5kO7eUFAK9
nuIbtqUS
=b6Jo
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Olof Johansson:
"A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the
end of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing
legacy mach/* include dependencies and moving platform
detection/config to drivers/soc. Also some updates/cleanup of
platform data.
- Core power domain support for Tegra platforms, and some
improvements in build test coverage by adding stubs for compile
test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI)
SMP support on i.MX7D, SoC ID setup for i.MX50, removal of platform
data and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip"
* tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (53 commits)
MAINTAINERS: Add myself as TEE subsystem reviewer
ixp4xx: fix spelling mistake in Kconfig "Devce" -> "Device"
hw_random: ixp4xx: Add OF support
hw_random: ixp4xx: Add DT bindings
hw_random: ixp4xx: Turn into a module
hw_random: ixp4xx: Use SPDX license tag
hw_random: ixp4xx: enable compile-testing
pata: ixp4xx: split platform data to its own header
soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h
PCI: ixp4xx: Add a new driver for IXP4xx
PCI: ixp4xx: Add device tree bindings for IXP4xx
ARM/ixp4xx: Make NEED_MACH_IO_H optional
ARM/ixp4xx: Move the virtual IObases
MAINTAINERS: ARM/MStar/Sigmastar SoCs: Add a link to the MStar tree
ARM: debug: add UART early console support for MSTAR SoCs
ARM: dts: ux500: Fix LED probing
ARM: imx: add smp support for imx7d
ARM: imx6q: drop of_platform_default_populate() from init_machine
arm64: dts: rockchip: Update RK3399 PCI host bridge window to 32-bit address memory
soc/tegra: fuse: Fix Tegra234-only builds
...
- Fix multi-MSI base vector number allocation (Sandor Bodo-Merle)
- Restrict multi-MSI support to uniprocessor kernel (Sandor Bodo-Merle)
* remotes/lorenzo/pci/iproc:
PCI: iproc: Support multi-MSI only on uniprocessor kernel
PCI: iproc: Fix multi-MSI base vector number allocation
- Decode PIO Posted/Non-posted Request correctly in error logging (Pali
Rohár)
- Work around incorrect Vendor ID in Marvell Armada 3700 (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Implement workaround for the readback value of VEND_ID
PCI: aardvark: Fix checking for PIO Non-posted Request
- Register IRQ handlers after device and data are ready (Javier Martinez
Canillas)
* pci/host/rockchip:
PCI: rockchip: Register IRQ handlers after device and data are ready
An IRQ handler may be called at any time after it is registered, so
anything it relies on must be ready before registration.
rockchip_pcie_subsys_irq_handler() and rockchip_pcie_client_irq_handler()
read registers in the PCIe controller, but we registered them before
turning on clocks to the controller. If either is called before the clocks
are turned on, the register reads fail and the machine hangs.
Similarly, rockchip_pcie_legacy_int_handler() uses rockchip->irq_domain,
but we installed it before initializing irq_domain.
Register IRQ handlers after their data structures are initialized and
clocks are enabled.
Found by enabling CONFIG_DEBUG_SHIRQ, which calls the IRQ handler when it
is being unregistered. An error during the probe path might cause this
unregistration and IRQ handler execution before the device or data
structure init has finished.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210608080409.1729276-1-javierm@redhat.com
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAmDa/58THHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXufBB/sGVIp1OhrtRFXeLJGJtbPPJzbh1w+K
hlDxthpN8uW7W7jyQRShiNUVwGX1QUiKBUH5g9oVKYBm0/srup4TivT2PiXPp4mC
7rPM9jcOD0ei9W2Z1/fjQvyorz37pQzq9GMF37FGqPM2mVuCl16QhdF5EqYjipCU
k34MyvjUPudmYot3gdiURyxrUljzw3KLfVXeg1Tpk0mXLZvm6OnyRn9ywgNJb+Pz
wn2+Om3hZCtccF2CUUS1LbMPFF97xy/CdAObyDuJyyXfyY7JFZ/guWBkQpi0tejQ
/+yJFYYZSo1lXV8xxB0t8LR9Vf6OxZNexn+0El4IUO4TZuAJcr4Q6fYp
=yOAz
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed-20210629' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv updates from Wei Liu:
"Just a few minor enhancement patches and bug fixes"
* tag 'hyperv-next-signed-20210629' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
PCI: hv: Add check for hyperv_initialized in init_hv_pci_drv()
Drivers: hv: Move Hyper-V extended capability check to arch neutral code
drivers: hv: Fix missing error code in vmbus_connect()
x86/hyperv: fix logical processor creation
hv_utils: Fix passing zero to 'PTR_ERR' warning
scsi: storvsc: Use blk_mq_unique_tag() to generate requestIDs
Drivers: hv: vmbus: Copy packets sent by Hyper-V out of the ring buffer
hv_balloon: Remove redundant assignment to region_start
tegra_pcie_ep_raise_msi_irq() shifted a signed 32-bit value left by 31
bits. The behavior of this is implementation-defined.
Replace the shift by BIT(), which is well-defined.
Found by cppcheck:
$ cppcheck --enable=all drivers/pci/controller/dwc/pcie-tegra194.c
Checking drivers/pci/controller/dwc/pcie-tegra194.c ...
drivers/pci/controller/dwc/pcie-tegra194.c:1829:23: portability: Shifting signed 32-bit value by 31 bits is implementation-defined behaviour. See condition at line 1826. [shiftTooManyBitsSigned]
appl_writel(pcie, (1 << irq), APPL_MSI_CTRL_1);
^
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210618160219.303092-1-jonathanh@nvidia.com
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Marvell Armada 3700 Functional Errata, Guidelines, and Restrictions
document describes in erratum 4.1 PCIe value of vendor ID (Ref #: 243):
The readback value of VEND_ID (RD0070000h [15:0]) is 1B4Bh, while it
should read 11ABh.
The firmware can write the correct value, 11ABh, through VEND_ID
(RD0076044h [15:0]).
Implement this workaround in aardvark driver for both PCI vendor id and PCI
subsystem vendor id.
This change affects and fixes PCI vendor id of emulated PCIe root bridge.
After this change emulated PCIe root bridge has correct vendor id.
Link: https://lore.kernel.org/r/20210624222621.4776-5-pali@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
PIO_NON_POSTED_REQ for PIO_STAT register is incorrectly defined. Bit 10 in
register PIO_STAT indicates the response is to a non-posted request.
Link: https://lore.kernel.org/r/20210624213345.3617-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Commit 275e88b06a ("PCI: tegra: Fix host link initialization") broke
host initialization during resume as it misses out calling the API
dw_pcie_setup_rc() which is required for host and MSI initialization.
Link: https://lore.kernel.org/r/20210504172157.29712-1-vidyas@nvidia.com
Fixes: 275e88b06a ("PCI: tegra: Fix host link initialization")
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
