__subn_get_opa_portinfo stores value returned by hfi1_get_ib_cfg() as
operational vls. hfi1_get_ib_cfg() returns vls_operational field in
hfi1_pportdata. The problem with this is that the value is always equal
to vls_supported field in hfi1_pportdata.
The logic to calculate operational_vls is to set value passed by FM
(in __subn_set_opa_portinfo routine). If no value is passed then
default value is stored in operational_vls.
Field actual_vls_operational is calculated on the basis of buffer
control table. Hence, modifying hfi1_get_ib_cfg() to return
actual_operational_vls when used with HFI1_IB_CFG_OP_VLS parameter
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Patel Jay P <jay.p.patel@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The handler for link init state (HLS_UP_INIT) notifies userspace
(update_statusp()) before enabling the device
(RCV_CTRL_RCV_PORT_ENABLE_SMASK) or setting the device state
(ppd->host_link_state). This causes a race condition where the
userspace thinks the interface is in the INIT state before the driver
has set that state.
Rework the code path to eliminate the race.
Delay setting the init state until after a HW settling period.
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Conflicts:
drivers/infiniband/hw/cxgb4/cm.c
drivers/infiniband/hw/qib/qib_driver.c
drivers/infiniband/hw/qib/qib_mad.c
There were minor fixups needed in these files. Just minor context diffs
due to patches from independent sources touching the same basic area.
Signed-off-by: Doug Ledford <dledford@redhat.com>
The early for-next branch was based on v4.14-rc2, while the shared pull
request I got from Mellanox used a v4.14-rc4 base. I'm making the
branch that was the shared Mellanox pull request the new for-next branch
and merging the early for-next branch into it.
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Switches test of .data field to
.function, since .data will be going away.
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Change serdes mode setting to use MISC_CONFIG_BITS in
VERIFY_CAP_LOCAL_LINK_WIDTH register. This method of
setting up serdes loopback is universally compatible
across all firmware versions.
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The s_ahgpsn was incorrectly placed in the read-mostly section of the QP
and the s_curr_size and s_hdrwords are oversized. The misplaced
s_ahgpsn will cause the read-mostly cachelines to thrash.
Place s_ahgpsn in the send side cache lines and correctly size and
s_hdrwords and s_cur_size to keep the send side cachelines at the same
size.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When the link is disabled and re-enabled, the host version bit is not
set again, so the firmware behaves as though it’s interacting with an
old driver. This causes LNI to get out of sync. The host version bit
needs to be set at load_8051_firmware() and _dc_start(). Currently, it's
only set at load_8051_firmware().
Create a common function to set the bit with the intent to make the code
more maintainable in the future, set the host version bit at _dc_start()
and modify the 8051 command API to prevent a deadlock as _dc_start() is
already holding the dc8051 lock.
Fixes: 913cc67159 ("IB/hfi1: Always perform offline transition")
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The addition of the VNIC contexts to num_rcv_contexts changes the
meaning of the sysfs value nctxts from available user contexts, to
user contexts + reserved VNIC contexts.
User applications that use nctxts are now broken.
Update the calculation so that VNIC contexts are used only if there are
hardware contexts available, and do not silently affect nctxts.
Update code to use the calculated VNIC context number.
Update the sysfs value nctxts to be available user contexts only.
Fixes: 2280740f01 ("IB/hfi1: Virtual Network Interface Controller (VNIC) HW support")
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Niranjana Vishwanathapura <Niranjana.Vishwanathapura@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: <Stable@vger.kernel.org> #v4.12+
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
hfi1_rcd_get_by_index assumes that the given index is in the correct
range. In most cases this is correct because the index is bounded by
a loop. For these cases, adding a range check to the function is
redundant.
For the use case that is not bounded by the loop range, a _safe wrapper
function is needed to validate the index before accessing the rcd array.
Add a _safe wrapper to _get_by_index to validate the index range.
Update appropriate call sites with the new _safe function.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
devdata->link_default is no longer variable
Maintain number of holes by moving dc_shutdown
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The HFI PCI IRQ code uses an obsolete PCI API. Update the code to use
the new PCI IRQ API and any necessary changes because of the new API.
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add state decodes for link width negotiation, verify cap time out
and secure data resolution failures.
Reviewed-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The general interrupt handler returns IRQ_HANDLED whether an IRQ
was handled or not.
Determine if an IRQ was handled and return the correct value.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Kamenee Arumugam <kamenee.arumugam@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
QSFP reset enables AOC transmitters by default. They should be off
before moving to high power mode to complete the setup. There is no
need to reset the QSFP during LNI failure as it was reset at link down.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Offline.quietDuration was added in the 8051 firmware, and the driver
only turns off the AOC transmitters when offline.quiet is reached.
However, the AOC transmitters need to be turned off at the new state.
Therefore, turn off the AOC transmitters at any offline substates
including offline.quiet and offline.quietDuration, then recheck we
reached offline.quiet to support backwards compatibility.
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Ratelimit error prints from sdma_interrupt function
that could swarm dmesg otherwise.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Grzegorz Morys <grzegorz.morys@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Do not track physical state separately from host_link_state.
Deduce physical state from host_link_state when required.
Change cache_physical_state to log_physical_state to make
sure host_link_state reflects hardwares physical state properly.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Check xchg returned value for queuing link down entry
to guarantee proper atomic value reads.
Fixes: 626c077c02 ("IB/hfi1: Prevent link down request double queuing")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Increase lid used in hfi1 driver to 32 bits. qib continues
to use 16 bit lids.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We introduce a struct hfi1_16b_header to support 16B headers.
16B bypass packets are received by the driver and processed
similar to 9B packets. Add basic support to handle 16B packets.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is a mixture of mutex and spinlocks to protect receive context
(rcd/uctxt) information. This is not used consistently.
Use the mutex to protect device receive context information only.
Use the spinlock to protect sub context information only.
Protect access to items in the rcd array with a spinlock and
reference count.
Remove spinlock around dd->rcd array cleanup. Since interrupts are
disabled and cleaned up before this point, this lock is not useful.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The rcd array can be accessed from user context or during interrupts.
Protecting this with a mutex isn't a good idea because the mutex should
not be used from an IRQ.
Protect the allocation and freeing of rcd array elements with a
spinlock.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Do not track logical state separately from host_link_state. Deduce
logical state from host_link_state when required. Transitions in
set_link_state and goto_offline already make sure host_link_state
reflects hardware's logical state properly.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Conflicts:
drivers/infiniband/core/iwcm.c - The rdma_netlink patches in
HEAD and the iwarp cm workqueue fix (don't use WQ_MEM_RECLAIM,
we aren't safe for that context) touched the same code.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Trivial fix to spelling mistake, rename variable 'continious'
to the correct spelling 'continuous'
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Always initiate an offline transition request
when a link down occurs. The firmware will
use this request to confirm that the driver
has seen the link down message. A host version
is set to indicate this driver behavior to the
firmware.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When link interrupts occur, multiple link down requests
could be queued up when only one is needed. This could get
the hfi1 out of sync with its link partner during LNI.
Only allow one link down request to be queued at any one time.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently, link down interrupts queue link entries
on a workqueue intended for sending events only.
Create a workqueue for queuing link events.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix issue where a disabled port can be enabled by
inserting a cable. The port should be explicitly
enabled instead.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is a window that allows other threads to read state of
'host_link_state' as a new, before the hardware actual state is set.
This patch closes the window by indicating a new state only after
hardware transition is complete.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is a window where the FM can read the buffer control table
and decide not to program buffers. When a port goes down, the code
clears the table and if it is not programmed, posted SDMA descriptors
will never complete due to no buffer credits.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
During PCIe initialization some registers' values from
PCI config space are saved in order to restore them later
(i.e. after reset). Restoring those value is done by a
function called restore_pci_variables, while saving them
is put directly into function hfi1_pcie_ddinit.
Move saving values to a separate function in the image
of restoring functionality.
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Bartlomiej Dudek <bartlomiej.dudek@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Code structure is not consistent for if/else blocks and break
instructions in set_link_state for case HLS_UP_INIT. Physical
state uses break in case of an error and if/else blocks for
logical use cases. These blocks should be implemented consistently.
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The hfi1_rcvctrl() function receives an index which it then converts
to an rcd. Since most functions have the rcd, use that instead.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The hfi1_<set|clear>_ctxt_<j|p>key functions take a context index and
look up the context based on that index.
Since the context index is being retrieved from the context, this
doesn't seem optimal.
Pass the context pointer for use, rather than the context index.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The array index for the rcd array is sized several different ways
throughout the code.
Use the user interface size (u16) as the standard size and update the
necessary code to reflect this.
u16 is large enough for the largest amount of supported contexts.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When the debugpat kernel boot flag is turned on the following
traces are printed:
[ 1884.793168] x86/PAT: Overlap at 0x90000000-0x92000000
[ 1884.803510] x86/PAT: reserve_memtype added [mem 0x91200000-0x9127ffff],
track uncached-minus, req write-combining, ret uncached-minus
[ 1884.818167] hfi1 0000:05:00.0: hfi1_0: WC Remapped RcvArray:
ffffc9000a980000
The ioremap_wc() clearly is not returning a write combining mapping due
to an overlap where the RcvArray is mapped in a uncached mapping prior
to creating the proposed write combining mapping.
The patch replaces the single base register for uncached CSRs that
used to overlap the RcvArray with two mappings. One, kregbase1, from the
bar0 up to the RcvArray and another, kregbase2, from the end of the
RcvArray to the pio send buffer space. A new dd field, base2_start,
is used to convert the zero-based offset in the CSR routines to the
correct kregbase1/kregbase2 mapping. A single direct write of the
RcvArray CSRs is replaced with hfi1_put_tid() to insure correct access
using the new disjoint mapping.
Additionally, the kregend field is deleted since it is only ever written.
patdebug now shows the RcvArray as write combining:
[ 35.688990] x86/PAT: reserve_memtype added [mem 0x91200000-0x9127ffff],
track write-combining, req write-combining, ret write-combining
To insulate from any potential issues with write combining, all
writeq are now flushed in hfi1_put_tid() and rcv_array_wc_fill().
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Ensure that return values from kernel PCI config access
API calls in HFI driver are checked and react properly if
they are not expected (i.e. not successful).
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Bartlomiej Dudek <bartlomiej.dudek@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
As the code stands today the array access in remap_intr() is OK. To
future proof the code though we should explicitly check to ensure the
index value is not outside of the valid range. This is not a straight
forward calculation so err on the side of caution.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds a trace for putting a TID and
for writing the RcvArray CSR.
The CSR access template can be easily extended for additional
CSR readq/writeq calls.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Change QSFP cable error events logging levels from info to error.
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix info array of host message flags by adding entry
for link width downgrade and reverse values for
BC SMA and BC PWR_MSG messages
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Bartlomiej Dudek <bartlomiej.dudek@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Ensure states returned to the Fabric Manager are consistent with
the OPA specification by caching the physical state along with the
logical state.
Reviewed-by: Stuart Summers <john.s.summers@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Andrzej Kotlowski <andrzej.kotlowski@intel.com>
Signed-off-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Spell receive correctly in OPA_LINKDOWN_REASON_RCV_ERROR
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
As the code stands today the array access in remap_intr() is OK. To
future proof the code though we should explicitly check to ensure the
index value is not outside of the valid range. This is not a straight
forward calculation so err on the side of caution.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
pci_enable_msix_range() and pci_disable_msix() have been deprecated.
Updating to the new pci_alloc_irq_vectors() interface.
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We move many common IB fields into the hfi1_packet structure and
set them up in a single function. This allows us to set the fields
in a single place and not deal with them throughout the driver.
Reviewed-by: Brian Welty <brian.welty@intel.com>
Reviewed-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Keep VL15 credits at 0 during LNI, before link-up. Store
VL15 credits value during verify cap interrupt and set
in after link-up. This addresses an issue where VL15 MAD
packets could be sent by one side of the link before
the other side is ready to receive them.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
