Configure NIX RX flowkey algorithm configuration to support
RSS (receive side scaling). Currently support for only L3/L4
2-tuple and 4-tuple hash of IPv4/v6/TCP/UDP/SCTP is added.
HW supports upto 32 different flowkey algorithms which SW
can define, this patch defines 9. NPC RX ACTION has to point
to one of these flowkey indices for RSS to work.
The configuration is dependent on NPC parse result's layer
info. So if NPC KPU profile changes suchthat LID/LTYPE values
of above said protocols change then this configuration will
most likely be effected.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for PF/VF drivers to configure NIX to
capture and/or strip VLAN tag from ingress packets.
Signed-off-by: Vamsi Attunuru <vamsi.attunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a RVU PF/VF to submit instructions to NIX AQ
via mbox. Instructions can be to init/write/read RQ/SQ/CQ/RSS
contexts. In case of read, context will be returned as part of
response to the mbox msg received.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Config LSO formats for TSOv4 and TSOv6 offloads.
These formats tell HW which fields in the TCP packet's
headers have to be updated while performing segmentation
offload.
Also report PF/VF drivers the LSO format indices as part
of response to NIX_LF_ALLOC mbox msg. These indices are
used in SQE extension headers while framing SQE for pkt
transmission with TSO offload.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize NIX admin queue (AQ) i.e alloc memory for
AQ instructions and for the results. All NIX LFs will submit
instructions to AQ to init/write/read RQ/SQ/CQ/RSS contexts
and in case of read, get context from result memory.
Also before configuring/using NIX block calibrate X2P bus
and check if NIX interfaces like CGX and LBK are in active
and working state.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a RVU PF/VF to submit instructions to NPA AQ
via mbox. Instructions can be to init/write/read Aura/Pool/Qint
contexts. In case of read, context will be returned as part of
response to the mbox msg received.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize NPA admin queue (AQ) i.e alloc memory for
AQ instructions and for the results. All NPA LFs will submit
instructions to AQ to init/write/read Aura/Pool contexts
and in case of read, get context from result memory.
Added some common APIs for allocating memory for a queue
and get IOVA in return, these APIs will be used by
NIX AQ and for other purposes.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware configures a certain number of MSIX vectors to each of
enabled RVU PF/VF. When a block LF is attached to a PF/VF, number
of MSIX vectors needed by that LF are set aside (out of PF/VF's
total MSIX vectors) and LF's msix_offset is configured in HW.
Also added support for a RVU PF/VF to retrieve that block LF's
MSIX vector offset information from AF via mbox.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scan all RVU blocks to find any 'LF to RVU PF/VF' mapping done by
low level firmware. If found any, mark them as used in respective
block's LF bitmap and also save mapped PF/VF's PF_FUNC info.
This is done to avoid reattaching a block LF to a different RVU PF/VF.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for mailbox interrupt and message
handling. Mapped mailbox region and registered a workqueue
for message handling. Enabled mailbox IRQ of RVU PFs
and registered a interrupt handler. When IRQ is triggered
work is added to the mbox workqueue for msgs to get processed.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Go through all BLKADDRs and check which ones are implemented
on this silicon and do a HW reset of each implemented block.
Also added all RVU AF and PF register offsets.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
