Avoid spamming the log. The backlight controller on DCN chips
gets powered down when the display is off, so if you attempt to
set the backlight level when the display is off, you'll get this
message. This isn't a problem as we cache the requested backlight
level if it's adjusted when the display is off and set it again
during modeset.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: nicholas.choi@amd.com
Cc: harry.wentland@amd.com
[Why]
FS video support regressed GPU scaling and the scaled buffer ends up
stuck in the top left of the screen at native size - full, aspect,
center scaling modes do not function.
This is because decide_crtc_timing_for_drm_display_mode() does not
get called when scaling is enabled.
[How]
Split recalculate timing and scaling into two different flags.
We don't want to call drm_mode_set_crtcinfo() for scaling, but we
do want to call it for FS video.
Optimize and move preferred_refresh calculation next to
decide_crtc_timing_for_drm_display_mode() like it used to be since
that's not used for FS video.
We don't need to copy over the VIC or polarity in the case of FS video
modes because those don't change.
Fixes: 6f59f229f8 ("drm/amd/display: Skip modeset for front porch change")
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Conditions that end up modifying the global dc state must be locked.
However, during mst allocate payload sequence, lock is already taken.
With StarTech 1.2 DP hub, we get an HPD RX interrupt for a reason other
than to indicate down reply availability right after sending payload
allocation. The handler again takes dc lock before calling the
dc's HPD RX handler. Due to this contention, the DRM thread which waits
for MST down reply never gets a chance to finish its waiting
successfully and ends up timing out. Once the lock is released, the hpd
rx handler fires and goes ahead to read from the MST HUB, but now its
too late and the HUB doesnt lightup all displays since DRM lacks error
handling when payload allocation fails.
[How]
Take lock only if there is a change in link status or if automated test
pattern bit is set. The latter fixes the null pointer dereference when
running certain DP Link Layer Compliance test.
Fixes: c8ea79a8a2 ("drm/amd/display: NULL pointer error during compliance test")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amd-drm-next-5.14-2021-05-19:
amdgpu:
- Aldebaran updates
- More LTTPR display work
- Vangogh updates
- SDMA 5.x GCR fixes
- RAS fixes
- PCIe ASPM support
- Modifier fixes
- Enable TMZ on Renoir
- Buffer object code cleanup
- Display overlay fixes
- Initial support for multiple eDP panels
- Initial SR-IOV support for Aldebaran
- DP link training refactor
- Misc code cleanups and bug fixes
- SMU regression fixes for variable sized arrays
- MAINTAINERS fixes for amdgpu
amdkfd:
- Initial SR-IOV support for Aldebaran
- Topology fixes
- Initial HMM SVM support
- Misc code cleanups and bug fixes
radeon:
- Misc code cleanups and bug fixes
- SMU regression fixes for variable sized arrays
- Flickering fix for Oland with multiple 4K displays
UAPI:
- amdgpu: Drop AMDGPU_GEM_CREATE_SHADOW flag.
This was always a kernel internal flag and userspace use of it has always been blocked.
It's no longer needed so remove it.
- amdkgd: HMM SVM support
Overview: https://patchwork.freedesktop.org/series/85562/
Porposed userspace: https://github.com/RadeonOpenCompute/ROCT-Thunk-Interface/tree/fxkamd/hmm-wip
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210520031258.231896-1-alexander.deucher@amd.com
To stay consistent with the user's setting.
v2: rebase on multi-eDP support
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1337
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
And cache the value. These can be used by the backlight callbacks
and modesetting functions.
v2: rebase on latest backlight changes.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1337
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Adds the firmware definition and missing cases statement
hooks for Beige Goby support in AMDGPU DM.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
amdgpu_dm_crtc_set_crc_source() will call
amdgpu_dm_crtc_configure_crc_source() to enable/disable CRC
generation. However, configuration will be deferred to stream enabled.
If stream is not enabled, current flow will still try to get/put vblank
refcount.
[How]
Return EINVAL to skip actions on vblank refcount when stream is not
enabled.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Chao-kai Wang <Stylon.Wang@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Once set ROI and do suspend/resume, current flow will not enable
OTG_CRC_CTL again due to we'll defer crc configuration when stream
is enabled.
[How]
Remove current suspend/resume function and have logic implemented into
amdgpu_dm_atomic_commit_tail()
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Chao-kai Wang <Stylon.Wang@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c: In function ‘amdgpu_dm_initialize_drm_device’:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:3726:7: error: implicit declaration of function ‘register_outbox_irq_handlers’; did you mean ‘register_hpd_handlers’? [-Werror=implicit-function-declaration]
3726 | if (register_outbox_irq_handlers(dm->adev)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
| register_hpd_handlers
Fixes: 81927e2808 ("drm/amd/display: Support for DMUB AUX")
Reviewed-by: Jude Shih <shenshih@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Jude Shish <Jude.Shih@amd.com>
Fixes:
At top level:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:633:13: warning: ‘dm_dmub_outbox1_low_irq’ defined but not used [-Wunused-function]
633 | static void dm_dmub_outbox1_low_irq(void *interrupt_params)
| ^~~~~~~~~~~~~~~~~~~~~~~
Fixes: 81927e2808 ("drm/amd/display: Support for DMUB AUX")
Reviewed-by: Jude Shih <shenshih@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Jude Shih <Jude.Shih@amd.com>
The DCN3 guards were dropped a while ago, this one must have
snuck in in a merge or something.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If GPU is in reset state, force enabling link will cause
unexpected behaviour.
[How]
Avoid handling HPD IRQ when GPU is in reset state.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nikola Cornij <nikola.cornij@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To process AUX transactions with DMUB using inbox1 and outbox1 mail boxes.
[How]
1) Added inbox1 command DMUB_CMD__DP_AUX_ACCESS to issue AUX commands
to DMUB in dc_process_dmub_aux_transfer_async(). DMUB processes AUX cmd
with DCN and sends reply back in an outbox1 message triggering an
outbox1 interrupt to driver.
2) In existing driver implementation, AUX commands are processed
synchronously by configuring DCN reg. But in DMUB AUX, driver sends an
inbox1 message and waits for a conditional variable (CV) which will be
signaled by outbox1 ISR.
3) DM will retrieve Outbox1 message and send back reply to upper layer
and complete the AUX command
Signed-off-by: Jude Shih <shenshih@amd.com>
Reviewed-by: Hanghong Ma <Hanghong.Ma@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently the assumption is that we are using a single eDP
connector so there will only be one backlight object. Need changes
to allow brightness update and reading for multiple eDP connectors.
[how]
- register a single device
- turn backlight link from a pointer to an array of pointers
- update brightness of all eDP links at the same time when request
is registered
- read brightness level only of the primary eDP panel
- turn current_backlight_pwm and targer_backlight_pwm debugfs enteries
into per connector enteries.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Similar to SST branch, gpio conflict also needs to be avoided on
MST. Without doing so, there is a chance that gpio conflict will
occur if multiple gpio interrupts arrive simultaneously.
[How]
By mutex locking/unlocking &aconnector->hpd_lock,
we won't get gpio conflict when handling hpd.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Acked-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In gpu reset dc_lock acquired in dm_suspend().
Asynchronously handle_hpd_rx_irq can also be called
through amdgpu_dm_irq_suspend->flush_work, which also
tries to acquire dc_lock. That causes a deadlock.
[How]
Check if amdgpu executing reset before acquiring dc_lock.
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Our driver supports overlay planes, and as expected, some userspace
compositor takes advantage of these features. If the userspace is not
enabling the cursor, they can use multiple planes as they please.
Nevertheless, we start to have constraints when userspace tries to
enable hardware cursor with various planes. Basically, we cannot draw
the cursor at the same size and position on two separated pipes since it
uses extra bandwidth and DML only run with one cursor.
For those reasons, when we enable hardware cursor and multiple planes,
our driver should accept variations like the ones described below:
+-------------+ +--------------+
| +---------+ | | |
| |Primary | | | Primary |
| | | | | Overlay |
| +---------+ | | |
|Overlay | | |
+-------------+ +--------------+
In this scenario, we can have the desktop UI in the overlay and some
other framebuffer attached to the primary plane (e.g., video). However,
userspace needs to obey some rules and avoid scenarios like the ones
described below (when enabling hw cursor):
+--------+
|Overlay |
+-------------+ +-----+-------+ +-| |--+
| +--------+ | +--------+ | | +--------+ |
| |Overlay | | |Overlay | | | |
| | | | | | | | |
| +--------+ | +--------+ | | |
| Primary | | Primary | | Primary |
+-------------+ +-------------+ +-------------+
+-------------+ +-------------+
| +--------+ | Primary |
| |Overlay | | |
| | | | |
| +--------+ | +--------+ |
| Primary | | |Overlay | |
+-------------+ +-| |--+
+--------+
If the userspace violates some of the above scenarios, our driver needs
to reject the commit; otherwise, we can have unexpected behavior. Since
we don't have a proper driver validation for the above case, we can see
some problems like a duplicate cursor in applications that use multiple
planes. This commit fixes the cursor issue and others by adding adequate
verification for multiple planes.
Change since V1 (Harry and Sean):
- Remove cursor verification from the equation.
Cc: Louis Li <Ching-shih.Li@amd.com>
Cc: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following build warnings.
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:
In function ‘dm_update_mst_vcpi_slots_for_dsc’:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:6242:46:
warning: variable ‘old_con_state’ set but not used
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:
In function ‘amdgpu_dm_commit_cursors’:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:7709:44:
warning: variable ‘new_plane_state’ set but not used
The variables were introduced to be used in iterators, but not used.
Use other iterators which don't require the unused variables.
Fixes: 8ad278062d ("drm/amd/display: Disable cursors before disabling planes")
Fixes: 29b9ba74f6 ("drm/amd/display: Recalculate VCPI slots for new DSC connectors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All the drivers that support the HDR metadata property have a similar
function to compare the metadata from one connector state to the next,
and force a mode change if they differ.
All these functions run pretty much the same code, so let's turn it into
an helper that can be shared across those drivers.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430094451.2145002-2-maxime@cerno.tech
All the drivers that implement HDR output call pretty much the same
function to initialise the hdr_output_metadata property, and while the
creation of that property is in a helper, every driver uses the same
code to attach it.
Provide a helper for it as well
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430094451.2145002-1-maxime@cerno.tech
amd-drm-fixes-5.13-2021-05-05:
amdgpu:
- MPO hang workaround
- Fix for concurrent VM flushes on vega/navi
- dcefclk is not adjustable on navi1x and newer
- MST HPD debugfs fix
- Suspend/resumes fixes
- Register VGA clients late in case driver fails to load
- Fix GEM leak in user framebuffer create
- Add support for polaris12 with 32 bit memory interface
- Fix duplicate cursor issue when using overlay
- Fix corruption with tiled surfaces on VCN3
- Add BO size and stride check to fix BO size verification
radeon:
- Fix off-by-one in power state parsing
- Fix possible memory leak in power state parsing
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210506033929.3875-1-alexander.deucher@amd.com
Our driver supports overlay planes, and as expected, some userspace
compositor takes advantage of these features. If the userspace is not
enabling the cursor, they can use multiple planes as they please.
Nevertheless, we start to have constraints when userspace tries to
enable hardware cursor with various planes. Basically, we cannot draw
the cursor at the same size and position on two separated pipes since it
uses extra bandwidth and DML only run with one cursor.
For those reasons, when we enable hardware cursor and multiple planes,
our driver should accept variations like the ones described below:
+-------------+ +--------------+
| +---------+ | | |
| |Primary | | | Primary |
| | | | | Overlay |
| +---------+ | | |
|Overlay | | |
+-------------+ +--------------+
In this scenario, we can have the desktop UI in the overlay and some
other framebuffer attached to the primary plane (e.g., video). However,
userspace needs to obey some rules and avoid scenarios like the ones
described below (when enabling hw cursor):
+--------+
|Overlay |
+-------------+ +-----+-------+ +-| |--+
| +--------+ | +--------+ | | +--------+ |
| |Overlay | | |Overlay | | | |
| | | | | | | | |
| +--------+ | +--------+ | | |
| Primary | | Primary | | Primary |
+-------------+ +-------------+ +-------------+
+-------------+ +-------------+
| +--------+ | Primary |
| |Overlay | | |
| | | | |
| +--------+ | +--------+ |
| Primary | | |Overlay | |
+-------------+ +-| |--+
+--------+
If the userspace violates some of the above scenarios, our driver needs
to reject the commit; otherwise, we can have unexpected behavior. Since
we don't have a proper driver validation for the above case, we can see
some problems like a duplicate cursor in applications that use multiple
planes. This commit fixes the cursor issue and others by adding adequate
verification for multiple planes.
Change since V1 (Harry and Sean):
- Remove cursor verification from the equation.
Cc: Louis Li <Ching-shih.Li@amd.com>
Cc: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This hasn't been well tested and leads to complete system hangs on DCN1
based systems, possibly others.
The system hang can be reproduced by gesturing the video on the YouTube
Android app on ChromeOS into full screen.
[How]
Reject atomic commits with non-zero drm_plane_state.src_x or src_y values.
v2:
- Add code comment describing the reason we're rejecting non-zero
src_x and src_y
- Drop gerrit Change-Id
- Add stable CC
- Based on amd-staging-drm-next
v3: removed trailing whitespace
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Cc: nicholas.kazlauskas@amd.com
Cc: amd-gfx@lists.freedesktop.org
Cc: alexander.deucher@amd.com
Cc: Roman.Li@amd.com
Cc: hersenxs.wu@amd.com
Cc: danny.wang@amd.com
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
This hasn't been well tested and leads to complete system hangs on DCN1
based systems, possibly others.
The system hang can be reproduced by gesturing the video on the YouTube
Android app on ChromeOS into full screen.
[How]
Reject atomic commits with non-zero drm_plane_state.src_x or src_y values.
v2:
- Add code comment describing the reason we're rejecting non-zero
src_x and src_y
- Drop gerrit Change-Id
- Add stable CC
- Based on amd-staging-drm-next
v3: removed trailing whitespace
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Cc: nicholas.kazlauskas@amd.com
Cc: amd-gfx@lists.freedesktop.org
Cc: alexander.deucher@amd.com
Cc: Roman.Li@amd.com
Cc: hersenxs.wu@amd.com
Cc: danny.wang@amd.com
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Accept non-linear buffers which use a multi-planar format, as long
as they don't use DCC.
Tested on GFX9 with NV12.
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 55fa622fe6.
The regression caused by the original patch has been
cleared, thus introduce back the change.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current list supports modifiers that have DCC_MAX_COMPRESSED_BLOCK
set to AMD_FMT_MOD_DCC_BLOCK_128B, while AMD_FMT_MOD_DCC_BLOCK_64B
is used instead by userspace.
[How]
Replace AMD_FMT_MOD_DCC_BLOCK_128B with AMD_FMT_MOD_DCC_BLOCK_64B
for modifiers with DCC supported.
Fixes: faa37f54ce ("drm/amd/display: Expose modifiers")
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Tested-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debugging reasons it can be beneficial to disable any hotplug and DP shortpulse interrupt handling.
[How]
Expose a debugfs to set a flag to bypass HPD IRQ handling and skip IRQ handling if flag is set.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit f4a9be998c.
The original commit was found to cause the following two issues
on sienna cichlid:
1. Refresh rate locked during vrrdemo
2. Display sticks on flipped landscape mode after changing
orientation, and cannot be changed back to regular landscape
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
The driver always wants to synchronize streams
to the first edge of master's vsync pulse.
In order to determine that we can read timing
flags that are used to program vsync.
Master stream's vsync polarity - Multi Display Stream Synchronization edge:
Negative - Falling Edge
Positive - Rising Edge
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Our CI enables drm.debug=0x4 logs and the dmesg is flooded with cursor
updates. We probably want to avoid spamming the log with DRM_DEBUG_KMS.
[how]
Define and use pr_debug macros instead of a few spammy DRM_DEBUG_*'s.
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When encoder validation of a display mode fails, retry with less bandwidth
heavy YCbCr420 color mode, if available. This enables some HDMI 1.4 setups
to support 4k60Hz output, which previously failed silently.
On some setups, while the monitor and the gpu support display modes with
pixel clocks of up to 600MHz, the link encoder might not. This prevents
YCbCr444 and RGB encoding for 4k60Hz, but YCbCr420 encoding might still be
possible. However, which color mode is used is decided before the link
encoder capabilities are checked. This patch fixes the problem by retrying
to find a display mode with YCbCr420 enforced and using it, if it is
valid.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When we have to debug VRR issues, we usually want to know the current
refresh rate; for this reason, it is handy to have a way to check in
real-time the refresh rate value. This commit introduces a kernel trace
that can provide such information.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
This was a regression introduced by commit:
drm/amd/display: Skip modeset for front porch change
Due to the change how timing parameters were set, scaled modes would
cause a black screen on some eDP panels. Would probably apply to
other displays (i.e. even non-eDP) that only have scaled modes,
but such case is not that usual for external displays.
[how]
Pick up crtc frame dimensions when programming the timing unless
it's FreeSync video mode.
Fixes: 6f59f229f8 ("drm/amd/display: Skip modeset for front porch change")
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Sometimes the primary plane might not be initialized (yet), which
causes dm_check_crtc_cursor to divide by zero.
Apparently a weird state before a S3-suspend causes the aforementioned
divide-by-zero error when resuming from S3. This was explained in
bug 212293 on Bugzilla.
To avoid this divide-by-zero error we check if the primary plane's fb
isn't NULL. If it's NULL the src_w and src_h attributes will be 0,
which would cause a divide-by-zero.
This fixes Bugzilla report 212293
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=212293
Fixes: 12f4849a1c ("drm/amd/display: check cursor scaling")
Reviewed-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Sefa Eyeoglu <contact@scrumplex.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
idle optimization was being disabled after commit.
[How]
check vblank count for display off and enable idle optimization based on this count.
Also,check added to ensure vblank count does not decrement, when count reaches 0.
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On initializing the framebuffer, call drm_any_plane_has_format to do a
check if the modifier is supported. drm_any_plane_has_format calls
dm_plane_format_mod_supported which is extended to validate that the
modifier is on the list of the plane's supported modifiers.
The bug was caught using igt-gpu-tools test: kms_addfb_basic.addfb25-bad-modifier
Tested on ChromeOS Zork by turning on the display, running an overlay
test, and running a YT video.
=== Changes from v1 ===
Explicitly handle DRM_FORMAT_MOD_INVALID modifier.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Mark Yacoub <markyacoub@chromium.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Convert IRQ-based prints from DRM_DEBUG_DRIVER to
the appropriate DRM log type, since IRQ-based
prints drown out the rest of the driver's
DRM_DEBUG_DRIVER messages.
v2: Update as per feedback to fine-tune for each
type of DRM log level.
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to log DMCUB trace buffer events as Linux kernel traces.
[How]
Register an IRQ handler for DMCUB outbox0 interrupt in amdgpu_dm,
and log the messages in the DMCUB tracebuffer to a new DMCUB
TRACE_EVENT as soon as we receive the outbox0 IRQ from DMCUB FW.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amd-drm-next-5.13-2021-03-23:
amdgpu:
- Debugfs cleanup
- Various cleanups and spelling fixes
- Flexible array cleanups
- Initial AMD Freesync HDMI
- Display fixes
- 10bpc dithering improvements
- Display ASSR support
- Clean up and unify powerplay and swsmu interfaces
- Vangogh fixes
- Add SMU gfx busy queues for RV/PCO
- PCIE DPM fixes
- S0ix fixes
- GPU metrics data fixes
- DCN secure display support
- Backlight type override
- Add initial support for Aldebaran
- RAS fixes
- Prime fixes for A+A systems
- Reset fixes
- Initial resource cursor support
- Drop legacy IO BAR requirements
- Various power fixes
amdkfd:
- MMU notifier fixes
- APU fixes
radeon:
- Debugfs cleanups
- Flexible array cleanups
UAPI:
- amdgpu: Add a new INFO ioctl interface to query video capabilities
rather than hardcoding them in userspace. This allows us to provide
fine grained asic capabilities (e.g., if a particular part is
bandwidth limited, we can limit the capabilities). Proposed userspace:
https://gitlab.freedesktop.org/leoliu/drm/-/commits/info_video_capshttps://gitlab.freedesktop.org/leoliu/mesa/-/commits/info_video_caps
- amdkfd: bump the driver version. There was a problem with reporting
some RAS features on older versions of the driver. Proposed userspace:
7cdd63475c
Danvet: A bunch of conflicts all over, but it seems to compile ... I
did put the call to dc_allow_idle_optimizations() on a single line
since it looked a bit too jarring to be left alone.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210324040147.1990338-1-alexander.deucher@amd.com
[Why]
Find out that when we are registering vertical interrupt0, we get
DC_IRQ_SOURCE_INVALID when call dc_interrupt_to_irq_source for
DCN_1_0__SRCID__OTG6_VERTICAL_INTERRUPT0_CONTROL.
After analyzing, it's due to the defined value for
DCN_1_0__SRCID__OTG6_VERTICAL_INTERRUPT0_CONTROL is not
(DCN_1_0__SRCID__OTG5_VERTICAL_INTERRUPT0_CONTROL + 1). It's not
incremental sequence.
[How]
Use an array to record all vertical interrupt0 SRCID. While registering
interrupt, use an incremental index to visit the array to get the right
SRCID to register.
Also add error handling to avoid potential pointer problem.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since this is a "revert of a revert", the end effect is that freesync
video is back to its original state, the way it was before the first
revert.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
vblank_workqueue is never released.
[How]
Free it upon dm finish.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Received compiling warning:
All warnings (new ones prefixed by >>):
>> drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:5574:5:
warning: no previous prototype for 'amdgpu_dm_crtc_late_register'
[-Wmissing-prototypes]
5574 | int amdgpu_dm_crtc_late_register(struct drm_crtc *crtc)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c: In
function 'dm_update_mst_vcpi_slots_for_dsc':
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:6405:46:
warning: variable 'old_con_state' set but not used
[-Wunused-but-set-variable]
6405 | struct drm_connector_state *new_con_state, *old_con_state;
| ^~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c: In
function 'amdgpu_dm_commit_cursors':
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:8006:44:
warning: variable 'new_plane_state' set but not used
[-Wunused-but-set-variable]
8006 | struct drm_plane_state *old_plane_state, *new_plane_state;
| ^~~~~~~~~~~~~~~
vim +/amdgpu_dm_crtc_late_register +5574
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c
5572
5573 #ifdef CONFIG_DRM_AMD_SECURE_DISPLAY
> 5574 int amdgpu_dm_crtc_late_register(struct drm_crtc *crtc)
5575 {
5576 crtc_debugfs_init(crtc);
5577
5578 return 0;
5579 }
5580 #endif
5581
[How]
Fix it with declaration as "static"
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dc_cursor_position do not initialise position.translate_by_source when
crtc or plane->state->fb is NULL. UBSAN caught this error in
dce110_set_cursor_position, as the value was garbage.
[How]
Initialise dc_cursor_position structure elements to 0 in handle_cursor_update
before calling get_cursor_position.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1471
Reported-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
