For devices that supports both regular and Ethertyped DSA tags, allow
the user to change the protocol.
Additionally, because there are ethernet controllers that do not
handle regular DSA tags in all cases, also allow the protocol to be
changed on devices with undocumented support for EDSA. But, in those
cases, make sure to log the fact that an undocumented feature has been
enabled.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All devices are capable of using regular DSA tags. Support for
Ethertyped DSA tags sort into three categories:
1. No support. Older chips fall into this category.
2. Full support. Datasheet explicitly supports configuring the CPU
port to receive FORWARDs with a DSA tag.
3. Undocumented support. Datasheet lists the configuration from
category 2 as "reserved for future use", but does empirically
behave like a category 2 device.
So, instead of listing the one true protocol that should be used by a
particular chip, specify the level of support for EDSA (support for
regular DSA is implicit on all chips). As before, we use EDSA for all
chips that fully supports it.
In upcoming changes, we will use this information to support
dynamically changing the tag protocol.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amethyst internal PHYs also report empty model number in MII_PHYSID2.
Fill in switch product number, as is done for Topaz and Peridot.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ALWAYS_GUARD_BAND_SCH_Q bit in TAS config register is descripted as
this:
0: Guard band is implemented for nonschedule queues to schedule
queues transition.
1: Guard band is implemented for any queue to schedule queue
transition.
The driver set guard band be implemented for any queue to schedule queue
transition before, which will make each GCL time slot reserve a guard
band time that can pass the max SDU frame. Because guard band time could
not be set in tc-taprio now, it will use about 12000ns to pass 1500B max
SDU. This limits each GCL time interval to be more than 12000ns.
This patch change the guard band to be only implemented for nonschedule
queues to schedule queues transition, so that there is no need to reserve
guard band on each GCL. Users can manually add guard band time for each
schedule queues in their configuration if they want.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit fee2d54641 ("net: phy: marvell: mv88e6390 temperature
sensor reading"), Linux reports the temperature of Topaz hwmon as
constant -75°C.
This is because switches from the Topaz family (88E6141 / 88E6341) have
the address of the temperature sensor register different from Peridot.
This address is instead compatible with 88E1510 PHYs, as was used for
Topaz before the above mentioned commit.
Create a new mapping table between switch family and PHY ID for families
which don't have a model number. And define PHY IDs for Topaz and Peridot
families.
Create a new PHY ID and a new PHY driver for Topaz's internal PHY.
The only difference from Peridot's PHY driver is the HWMON probing
method.
Prior this change Topaz's internal PHY is detected by kernel as:
PHY [...] driver [Marvell 88E6390] (irq=63)
And afterwards as:
PHY [...] driver [Marvell 88E6341 Family] (irq=63)
Signed-off-by: Pali Rohár <pali@kernel.org>
BugLink: https://github.com/globalscaletechnologies/linux/issues/1
Fixes: fee2d54641 ("net: phy: marvell: mv88e6390 temperature sensor reading")
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are a few more bits in the GSWIP_MII_CFG register for which we
did rely on the boot-loader (or the hardware defaults) to set them up
properly.
For some external RMII PHYs we need to select the GSWIP_MII_CFG_RMII_CLK
bit and also we should un-set it for non-RMII PHYs. The
GSWIP_MII_CFG_RMII_CLK bit is ignored for other PHY connection modes.
The GSWIP IP also supports in-band auto-negotiation for RGMII PHYs when
the GSWIP_MII_CFG_RGMII_IBS bit is set. Clear this bit always as there's
no known hardware which uses this (so it is not tested yet).
Clear the xMII isolation bit when set at initialization time if it was
previously set by the bootloader. Not doing so could lead to no traffic
(neither RX nor TX) on a port with this bit set.
While here, also add the GSWIP_MII_CFG_RESET bit. We don't need to
manage it because this bit is self-clearning when set. We still add it
here to get a better overview of the GSWIP_MII_CFG register.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable@vger.kernel.org
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY auto polling on the GSWIP hardware can be used so link changes
(speed, link up/down, etc.) can be detected automatically. Internally
GSWIP reads the PHY's registers for this functionality. Based on this
automatic detection GSWIP can also automatically re-configure it's port
settings. Unfortunately this auto polling (and configuration) mechanism
seems to cause various issues observed by different people on different
devices:
- FritzBox 7360v2: the two Gbit/s ports (connected to the two internal
PHY11G instances) are working fine but the two Fast Ethernet ports
(using an AR8030 RMII PHY) are completely dead (neither RX nor TX are
received). It turns out that the AR8030 PHY sets the BMSR_ESTATEN bit
as well as the ESTATUS_1000_TFULL and ESTATUS_1000_XFULL bits. This
makes the PHY auto polling state machine (rightfully?) think that the
established link speed (when the other side is Gbit/s capable) is
1Gbit/s.
- None of the Ethernet ports on the Zyxel P-2812HNU-F1 (two are
connected to the internal PHY11G GPHYs while the other three are
external RGMII PHYs) are working. Neither RX nor TX traffic was
observed. It is not clear which part of the PHY auto polling state-
machine caused this.
- FritzBox 7412 (only one LAN port which is connected to one of the
internal GPHYs running in PHY22F / Fast Ethernet mode) was seeing
random disconnects (link down events could be seen). Sometimes all
traffic would stop after such disconnect. It is not clear which part
of the PHY auto polling state-machine cauased this.
- TP-Link TD-W9980 (two ports are connected to the internal GPHYs
running in PHY11G / Gbit/s mode, the other two are external RGMII
PHYs) was affected by similar issues as the FritzBox 7412 just without
the "link down" events
Switch to software based configuration instead of PHY auto polling (and
letting the GSWIP hardware configure the ports automatically) for the
following link parameters:
- link up/down
- link speed
- full/half duplex
- flow control (RX / TX pause)
After a big round of manual testing by various people (who helped test
this on OpenWrt) it turns out that this fixes all reported issues.
Additionally it can be considered more future proof because any
"quirk" which is implemented for a PHY on the driver side can now be
used with the GSWIP hardware as well because Linux is in control of the
link parameters.
As a nice side-effect this also solves a problem where fixed-links were
not supported previously because we were relying on the PHY auto polling
mechanism, which cannot work for fixed-links as there's no PHY from
where it can read the registers. Configuring the link settings on the
GSWIP ports means that we now use the settings from device-tree also for
ports with fixed-links.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Fixes: 3e6fdeb28f ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock")
Cc: stable@vger.kernel.org
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Guobin Huang <huangguobin4@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Guobin Huang <huangguobin4@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three minor changes:
- When disabling PLL, there is no need to call core_write_mmd_indirect
directly, use the core_write wrapper instead like the rest of the code
in the function does. This change helps with consistency and
readability. Move the comment to the definition of
core_read_mmd_indirect where it belongs.
- Disable both core and TRGMII Tx clocks prior to reconfiguring.
Previously, only the core clock was disabled, but not TRGMII Tx clock.
So disable both, then configure them, then re-enable both, for
consistency.
- The core clock enable bit (REG_GSWCK_EN) is written redundantly three
times. Simplify the code and only write the register only once at the
end of clock reconfiguration to enable both core and TRGMII Tx clocks.
Tested on Ubiquiti ER-X running the GMAC0 and MT7530 in TRGMII mode.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xMII interface clock depends on the PHY interface (MII, RMII, RGMII)
as well as the current link speed. Explicitly configure the GSWIP to
automatically select the appropriate xMII interface clock.
This fixes an issue seen by some users where ports using an external
RMII or RGMII PHY were deaf (no RX or TX traffic could be seen). Most
likely this is due to an "invalid" xMII clock being selected either by
the bootloader or hardware-defaults.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The premise of this change is that the switchdev port attributes and
objects offloaded by ocelot might have been missed when we are joining
an already existing bridge port, such as a bonding interface.
The patch pulls these switchdev attributes and objects from the bridge,
on behalf of the 'bridge port' net device which might be either the
ocelot switch interface, or the bonding upper interface.
The ocelot_net.c belongs strictly to the switchdev ocelot driver, while
ocelot.c is part of a library shared with the DSA felix driver.
The ocelot_port_bridge_leave function (part of the common library) used
to call ocelot_port_vlan_filtering(false), something which is not
necessary for DSA, since the framework deals with that already there.
So we move this function to ocelot_switchdev_unsync, which is specific
to the switchdev driver.
The code movement described above makes ocelot_port_bridge_leave no
longer return an error code, so we change its type from int to void.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the driver name, ASIC ID and the switch name via devlink. This is a
useful information for user space tooling.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify compatible string against hardware.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to use all PHYs on GRX300 and GRX330. The ARX300
has 3 and the GRX330 has 4 integrated PHYs connected to different
ports compared to VRX200. Each integrated PHY can work as single
Gigabit Ethernet PHY (GMII) or as double Fast Ethernet PHY (MII).
Allowed port configurations:
xRX200:
GMAC0: RGMII, MII, REVMII or RMII port
GMAC1: RGMII, MII, REVMII or RMII port
GMAC2: GPHY0 (GMII)
GMAC3: GPHY0 (MII)
GMAC4: GPHY1 (GMII)
GMAC5: GPHY1 (MII) or RGMII port
xRX300:
GMAC0: RGMII port
GMAC1: GPHY2 (GMII)
GMAC2: GPHY0 (GMII)
GMAC3: GPHY0 (MII)
GMAC4: GPHY1 (GMII)
GMAC5: GPHY1 (MII) or RGMII port
xRX330:
GMAC0: RGMII, GMII or RMII port
GMAC1: GPHY2 (GMII)
GMAC2: GPHY0 (GMII)
GMAC3: GPHY0 (MII) or GPHY3 (GMII)
GMAC4: GPHY1 (GMII)
GMAC5: GPHY1 (MII), RGMII or RMII port
Tested on D-Link DWR966 (xRX330) with OpenWRT.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0b5294483c ("net: dsa: mv88e6xxx: scratch: Fixup kerneldoc")
has addressed some but not all kerneldoc warnings for the Global 2
Scratch register accessors. Namely, we have some mismatches between
the function names in the kerneldoc and the ones in the actual code.
Let's adjust the comments so that they match the functions they're
sitting next to.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Remove CONFIG_HAVE_NET_DSA.
CONFIG_HAVE_NET_DSA is a legacy leftover from the times when drivers
should have selected CONFIG_NET_DSA manually.
Currently, all drivers has explicit 'depends on NET_DSA', so this is
no more needed.
2. CONFIG_HAVE_NET_DSA dependencies became CONFIG_NET_DSA's ones.
- dropped !S390 dependency which was introduced to be sure NET_DSA
can select CONFIG_PHYLIB. DSA migrated to Phylink almost 3 years
ago and the PHY library itself doesn't depend on !S390 since
commit 870a2b5e4f ("phylib: remove !S390 dependeny from Kconfig");
- INET dependency is kept to be sure we can select NET_SWITCHDEV;
- NETDEVICES dependency is kept to be sure we can select PHYLINK.
3. DSA drivers menu now depends on NET_DSA.
Instead on 'depends on NET_DSA' on every single driver, the entire
menu now depends on it. This eliminates a lot of duplicated lines
from Kconfig with no loss (when CONFIG_NET_DSA=m, drivers also can
be only m or n).
This also has a nice side effect that there's no more empty menu on
configurations without DSA.
4. Kbuild will now descend into 'drivers/net/dsa' only when
CONFIG_NET_DSA is y or m.
This is safe since no objects inside this folder can be built without
DSA core, as well as when CONFIG_NET_DSA=m, no objects can be
built-in.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e9bf96943b.
The topic of the reverted patch is the support for switches with global
VLAN filtering, added by commit 061f6a505a ("net: dsa: Add
ndo_vlan_rx_{add, kill}_vid implementation"). Be there a switch with 4
ports swp0 -> swp3, and the following setup:
ip link add br0 type bridge vlan_filtering 1
ip link set swp0 master br0
ip link set swp1 master br0
What would happen with VLAN-tagged traffic received on standalone ports
swp2 and swp3? Well, it would get dropped, were it not for the
.ndo_vlan_rx_add_vid and .ndo_vlan_rx_kill_vid implementations (called
from vlan_vid_add and vlan_vid_del respectively). Basically, for DSA
switches where VLAN filtering is a global attribute, we enforce the
standalone ports to have 'rx-vlan-filter: off [fixed]' in their ethtool
features, which lets the user know that all VLAN-tagged packets that are
not explicitly added in the RX filtering list are dropped.
As for the sja1105 driver, at the time of the reverted patch, it was
operating in a pretty handicapped mode when it had ports under a bridge
with vlan_filtering=1. Specifically, it was unable to terminate traffic
through the CPU port (for further explanation see "Traffic support" in
Documentation/networking/dsa/sja1105.rst).
However, since then, the sja1105 driver has made considerable progress,
and that limitation is no longer as severe now. Specifically, since
commit 2cafa72e51 ("net: dsa: sja1105: add a new
best_effort_vlan_filtering devlink parameter"), the driver is able to
perform CPU termination even when some ports are under bridges with
vlan_filtering=1. Then, since commit 8841f6e63f ("net: dsa: sja1105:
make devlink property best_effort_vlan_filtering true by default"), this
even became the default operating mode.
So we can now take advantage of the logic in the DSA core.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These switches have two modes of classifying broadcast:
1. Broadcast is multicast.
2. Broadcast is its own unique thing that is always flooded
everywhere.
This driver uses the first option, making sure to load the broadcast
address into all active databases. Because of this, we can support
per-port broadcast flooding by (1) making sure to only set the subset
of ports that have it enabled whenever joining a new bridge or VLAN,
and (2) by updating all active databases whenever the setting is
changed on a port.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a user to control automatic learning per port.
Many chips have an explicit "LearningDisable"-bit that can be used for
this, but we opt for setting/clearing the PAV instead, as it works on
all devices at least as far back as 6083.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In accordance with the comment in dsa_port_bridge_leave, standalone
ports shall be configured to flood all types of traffic. This change
aligns the mv88e6xxx driver with that policy.
Previously a standalone port would initially not egress any unknown
traffic, but after joining and then leaving a bridge, it would.
This does not matter that much since we only ever send FROM_CPUs on
standalone ports, but it seems prudent to make sure that the initial
values match those that are applied after a bridging/unbridging cycle.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the conventional declaration style of a MAC address in the
kernel (u8 addr[ETH_ALEN]) for the broadcast address, then set it
using the existing helper.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware has a somewhat quirky protocol for reading out the VTU
entry for a particular VID. But there is no reason why we cannot
create a better API for ourselves in the driver.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the intricacies of correctly iterating over the VTU to a common
implementation.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is a part of a LAG, the ATU will create dynamic entries
belonging to the LAG ID when learning is enabled. So trying to
fast-age those out using the constituent port will have no
effect. Unfortunately the hardware does not support move operations on
LAGs so there is no obvious way to transform the request to target the
LAG instead.
Instead we document this known limitation and at least avoid wasting
any time on it.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM4908 has only 1 RGMII reg for controlling port 7.
Fixes: 73b7a60479 ("net: dsa: bcm_sf2: support BCM4908's integrated switch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple macro like REG_RGMII_CNTRL_P() is insufficient as:
1. It doesn't validate port argument
2. It doesn't support chipsets with non-lineral RGMII regs layout
Missing port validation could result in getting register offset from out
of array. Random memory -> random offset -> random reads/writes. It
affected e.g. BCM4908 for REG_RGMII_CNTRL_P(7).
Fixes: a78e86ed58 ("net: dsa: bcm_sf2: Prepare for different register layouts")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree support to b53_mmap.c while keeping platform devices support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 16-bit Port Policy CTL register from older chips is on 6393x changed
to Port Policy MGMT CTL, which can access more data, but indirectly and
via 8-bit registers.
The original 16-bit value is divided into first two 8-bit register in
the Port Policy MGMT CTL.
We can therefore use the previous code to compute the mask and shift,
and then
- if 0 <= shift < 8, we access register 0 in Port Policy MGMT CTL
- if 8 <= shift < 16, we access register 1 in Port Policy MGMT CTL
There are in fact other possible policy settings for Amethyst which
could be added here, but this can be done in the future.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Pavana Sharma <pavana.sharma@digi.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6393X device is a single-chip integration of a 11-port
Ethernet switch with eight integrated Gigabit Ethernet (GbE)
transceivers and three 10-Gigabit interfaces.
This patch adds functionalities specific to mv88e6393x family (88E6393X,
88E6193X and 88E6191X).
The main differences between previous devices and this one are:
- port 0 can be a SERDES port
- all SERDESes are one-lane, eg. no XAUI nor RXAUI
- on the other hand the SERDESes can do USXGMII, 10GBASER and 5GBASER
(on 6191X only one SERDES is capable of more than 1g; USXGMII is not
yet supported with this change)
- Port Policy CTL register is changed to Port Policy MGMT CTL register,
via which several more registers can be accessed indirectly
- egress monitor port is configured differently
- ingress monitor/CPU/mirror ports are configured differently and can be
configured per port (ie. each port can have different ingress monitor
port, for example)
- port speed AltBit works differently than previously
- PHY registers can be also accessed via MDIO address 0x18 and 0x19
(on previous devices they could be accessed only via Global 2 offsets
0x18 and 0x19, which means two indirections; this feature is not yet
leveraged with thiis commit)
Co-developed-by: Ashkan Boldaji <ashkan.boldaji@digi.com>
Signed-off-by: Ashkan Boldaji <ashkan.boldaji@digi.com>
Signed-off-by: Pavana Sharma <pavana.sharma@digi.com>
Co-developed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two implementations of the .set_egress_port method, and both
of them, if successful, set chip->*gress_dest_port variable.
To avoid code repetition, wrap this method into
mv88e6xxx_set_egress_port.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Pavana Sharma <pavana.sharma@digi.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning 0 is no more an error case with MV88E6393 family
which has serdes lane numbers 0, 9 or 10.
So with this change .serdes_get_lane will return lane number
or -errno (-ENODEV or -EOPNOTSUPP).
Signed-off-by: Pavana Sharma <pavana.sharma@digi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These tags are used on BCM5325, BCM5365 and BCM63xx switches.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM63xx switches are present on bcm63xx and bmips devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support port MDB and bridge flag operations.
As the hardware can manage multicast forwarding itself, offload_fwd_mark
can be unconditionally set to true.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value 'rc' maybe overwrite to 0 in the flow_action_for_each
loop, the error code from the offload not support error handling will
not set. This commit fix it to return -EOPNOTSUPP.
Fixes: 6a56e19902 ("flow_offload: reject configuration of packet-per-second policing in offload drivers")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing of_match_table to allow device tree probing.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch implements unicast and multicast filtering per port.
Add support for it. By default filtering is disabled.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM4908 switch has 256 CFP entrie, update that setting so CFP can be
used.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow to dump the FDB table via devlink. This is a useful debugging feature.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two functions which need to populate fdb entries. Move that to a
helper function.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hellcreek_select_vlan() takes a boolean instead of an integer.
So, use false accordingly.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow to dump the VLAN table via devlink. This especially useful, because the
driver internally leverages VLANs for the port separation. These are not visible
via the bridge utility.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will allow users to configures packet-per-second policing
in the software datapath. In preparation for this, teach all drivers that
support offload of the policer action to reject such configuration as
currently none of them support it.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some SoCs (e.g. BCM4908, BCM631[345]8) SF2 has an integrated
crossbar. It allows connecting its selected external ports to internal
ports. It's used by vendors to handle custom Ethernet setups.
BCM4908 has following 3x2 crossbar. On Asus GT-AC5300 rgmii is used for
connecting external BCM53134S switch. GPHY4 is usually used for WAN
port. More fancy devices use SerDes for 2.5 Gbps Ethernet.
┌──────────┐
SerDes ─── 0 ─┤ │
│ 3x2 ├─ 0 ─── switch port 7
GPHY4 ─── 1 ─┤ │
│ crossbar ├─ 1 ─── runner (accelerator)
rgmii ─── 2 ─┤ │
└──────────┘
Use setup data based on DT info to configure BCM4908's switch port 7.
Right now only GPHY and rgmii variants are supported. Handling SerDes
can be implemented later.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
