Currently need ptk/gtk wmi peer flags in wmi peer assoc cmd
are set based on the rsnie and wpaie of the bss from the bss list.
Since this bss list is not updated with current BSSID for AP mode,
we may not find bss from the bss list. Which results in ptk/gtk peer
flags are not set in the wmi peer assoc cmd. Due to this EAPOL frames
are going in data rates instead of management rates.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591771841-25503-1-git-send-email-vnaralas@codeaurora.org
Add support for collecting and dumping the ring backpressure
stats via debugfs. Stats are dumped only if events are
received for the specific ring.
Below command can be used to obtain these stats as part of soc dp stats.
cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats
Sample Output - When No stats available:
Backpressure Stats
==================
No Ring Backpressure stats received
Sample Output - When ring bp stats available for specific ring
Backpressure Stats
==================
Ring: REO2SW1_RING
count: 1
hp: 2
tp: 2
seen before: 4ms
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591768308-32005-3-git-send-email-srirrama@codeaurora.org
Add support for dp tx error stats which logs tx failure reasons due
to ring full condition, etc. This stats is added in soc_dp_stats
which was earlier used as soc_rx_stats so that all dp related info
are logged in same file.
Below is an example usage,
root@OpenWrt:/# cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats
SOC RX STATS:
err ring pkts: 0
Invalid RBM: 0
<snip>
SOC TX STATS:
Ring Full Failures:
ring0: 4
ring1: 3
ring2: 5
Misc Transmit Failures: 2
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591768308-32005-2-git-send-email-srirrama@codeaurora.org
spectral scan control interface is exposed through debugfs eentry.
Relayfs is used to collect the spectral data. These interfaces are
similar to ath10k spectral.
spectral debugfs interfaces are below,
echo background > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan0 > fft_samples.dump
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591688014-26441-2-git-send-email-periyasa@codeaurora.org
Add direct buffer ring (dbring) with helper API, which is used by the
spectral scan. Initialise the direct buffer ring based on the dma ring
capability, which get announced in the wmi service ready extended event.
This ring is slightly changed from data path rings. Compare to data path
ring this ring shares the hp and tp address to firmware though WMI commands.
Also the replenish buffer size is derived from firmware announcement.
driver receive indication through WMI event
WMI_PDEV_DMA_RING_BUF_RELEASE_EVENTID.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591688014-26441-1-git-send-email-periyasa@codeaurora.org
Current design supports only AHB interface for
11ax chipset. Refactor the code by adding hif layer
for bus level abstraction to support PCI based device.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200506094400.4740-2-govinds@codeaurora.org
This patch adds support for ethernet rxtx mode to the driver. The feature
is enabled via a new module parameter. If enabled to driver will enable
the feature on a per vif basis if all other requirements were met.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200430152814.18481-1-john@phrozen.org
IPQ8074 HW supports three TCL rings for tx. Currently these rings
are mapped based on the Access categories, viz. VO, VI, BE, BK.
In case, one of the traffic type dominates, then it could stress
the same tcl rings. Rather, it would be optimal to make use of all
the rings in a round robin fashion irrespective of the traffic type
so that the load could be evenly distributed among all the rings.
Also, in case the selected ring is busy or full, a retry mechanism
is used to ensure other available ring is selected without dropping
the packet.
In SMP systems, this change avoids a single CPU from getting hogged
when heavy traffic of same category is transmitted.
The tx completion interrupts corresponding to the used tcl ring
would be more which causes the assigned CPU to get hogged.
Distribution of tx packets to different tcl rings helps balance
this load.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586782622-22570-1-git-send-email-srirrama@codeaurora.org
Rx_filter flags are set with default filter flags during
wifi up/down sequence even though the 'ext_rx_stats' debugfs
is enabled as 1. So, that we are not getting proper per peer
rx_stats.
Hence, fixing this by setting the missing rx_filter when
ext_rx_stats is already set/enabled.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586538405-16226-3-git-send-email-mkenna@codeaurora.org
Pktlog data are different among the chipset & chipset versions.
As part of enhancing the user space script to decode the pktlog
trace events generated, it is desirable to know which chipset or
which chipset version has provided the events and thereby decode
the pktlogs appropriately.
Pktlog checksum helps to determine the chipset variant which is
given by the firmware in the struct wmi_ready_event.
Pktlog checksums are computed during the firmware build.
So, adding that pktlog checksum in the pklog trace events.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585234155-30574-1-git-send-email-mkenna@codeaurora.org
Add support to test aggregation procedures (addba/addba_resp/delba)
manually by adding the required callbacks in sta debugfs files.
To enable automatic aggregation in target,
echo 0 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
For manual mode,
echo 1 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
To send addba response,
echo 0 25 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/addba_resp
To send addba,
echo 1 32 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/addba
To send delba,
echo 0 1 37 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/delba
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585213026-28406-1-git-send-email-mkenna@codeaurora.org
As Hash based reo destination selection is configured,
the decapped packets reach different reo destintion rings
based on the destintaion ring selected for the computed hash (based on
the 5-tuple {ip src/ip dst/src port/dst port/protocol}) by hw and
as configured by driver.
Hence the current implementation of amsdu list based processing after all
the subframes of amsdu are received (since all msdu's for a pdev are
received in same reo dest ring), is not applicable here and hence is
replaced with per msdu based handling as these subframes
can be received in different reo dest rings.
Also, as some of the rx descriptor fields might be valid only for the
first msdu (for ex. received 80211 header, encryption type, etc),
it might not be useful now as we cannot sync between different
subframes received in different rings. Hence do not rely on those
fields and replace them with fieds valid only on per msdu descriptors.
Also cache other details such as encryption type for a peer so that
it can be reused when a packet is received from it.
Co-developed-by: Tamizh Chelvam Raja <tamizhr@codeaurora.org>
Signed-off-by: Tamizh Chelvam Raja <tamizhr@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dumping the SRNG stats during FW assert, this would help
in debugging ring stuck issues.
Co-developed-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enabling PN checking in the hardware; hardware checks
the PN of the received packets and reports the errors
to the host for further handling; default action is to
drop such packets. TSC (TKIP sequence counter)
validation is also offloaded.
Hardware validates PN/TSC only for unicast packets;
for group addressed packets, PN validation is done
in mac80211.
PN errors are reported to the driver via WBM RX release
ring and can be dumped by using the following command.
"cat /sys/kernel/debug/ath11k/soc_rx_stats | grep -i pn"
Sample Output:
PN check fail: 210
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
IPQ8074 HW has support to verify the PN of the received frames.
For all frames except for fragmented ones, HW checks the PN and
delivers them to the driver. For fragmented frames, driver is
required to do a little more; it has to reassemble the fragments
and then reinject them to the HW for verifying the PN. Currently,
to keep the logic simple, PN verifcation is disabled in HW and is
handled in mac80211 for all the frames (fragmented and unfragmented).
On the contrary, offloading PN Validation to the HW brings important
benefits. It reduces CPU cycles spent on the host CPU for verifying
the same; helps in enabling features which improve performance like
mac80211 fast RX path, enabling multiple REO rings for parallel RX
processing, 802.11 decapsulation offloading. All these features are
dependent on PN offload which in turn is dependent on handling of
the received fragments in the driver.
When TKIP security is used, additional handling is required while
processing the fragments; since MIC is computed on an MSDU in TKIP,
only the last fragment has the MIC info. In this case, driver has to
compute the MIC after reassembly and compare it against the MIC
present in the frame. For this, MICHAEL_MIC kernel crypto library
APIs are used and the dependencies are appropriately set.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Thermal cooling device support is added to control the temperature by
throttling the data transmission for the given duration. Throttling is
done by suspending all data tx queues by given percentage of time. The
thermal device allows user to configure duty cycle.
Throttling can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder.
/sys/class/ieee80211/phy*/device/cooling_device.
To set duty cycle as 40%,
echo 40 >/sys/class/ieee80211/phy*/device/cooling_device/cur_state
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In multi AP VAP scenario, when user bring down the interfaces. mac80211 mark
the interface down for the duplicated VAP and removed from the
local->interfaces list. ath11k_mac_get_arvif() is dependent on
ieee80211_iterate_active_interfaces_atomic() API to find the vdev id
in a given radio. In disassociation path, ath11k_mac_get_arvif() not
able to find the given vdev id since that VAP is removed from the
local->interfaces list. since sta_state callback throws error, mac80211 log
the below WARN_ON_ONCE message.
Fixed it by storing the allocated_vdev_map in each radio structure to maintain
the created vdev id bits. so that we can directly mask this against the given
vdev_id to find out the ar from the vdev_id.
WARN LOG:
WARNING: at net/mac80211/sta_info.c:1008
CPU: 2 PID: 2135 Comm: hostapd Not tainted #1
Hardware name: Qualcomm Technologies, Inc. IPQ807x/AP-HK01-C1 (DT)
task: ffffffc03a43d800 ti: ffffffc03a43d800 task.ti: ffffffc03a43d800
PC is at sta_set_sinfo+0x9dc/0xad4 [mac80211]
LR is at sta_set_sinfo+0x9cc/0xad4 [mac80211]
pc : [<ffffffbffce2a008>] lr : [<ffffffbffce29ff8>] pstate: 20000145
sp : ffffffc02cedb5f0
x29: ffffffc02cedb5f0 x28: ffffffc03a43d800
x27: 0000000000000014 x26: 0000000000000001
x25: ffffffc02cfc4000 x24: ffffffc036905508
x23: 0000000000000012 x22: ffffffc02cedb670
x21: ffffffc03bc64880 x20: ffffffc036904f80
x19: ffffffc02ae31000 x18: 00000000b019f3a1
x17: 0000000057f30331 x16: 00000000d8d1998e
x15: 0000000000000066 x14: 393a35383a36343a
x13: 6337203a6e6f6974 x12: 6174732065746169
x11: 636f737361736964 x10: 206f742064656c69
x9 : 6146203a31696669 x8 : 6337203a6e6f6974
x7 : 6174732065746169 x6 : ffffffc0008c33f6
x5 : 0000000000000000 x4 : 0000000000000000
x3 : 0000000000000000 x2 : 00000000ffffff92
x1 : 0000000000000000 x0 : ffffffbffcea1091
---[ end trace 63c4b1c527345d5a ]---
Call trace:
[<ffffffbffce2a008>] sta_set_sinfo+0x9dc/0xad4 [mac80211]
[<ffffffbffce2a2c4>] __sta_info_flush+0xec/0x130 [mac80211]
[<ffffffbffce3dc48>] ieee80211_nan_func_match+0x1a34/0x23e4 [mac80211]
[<ffffffbffcde03e0>] __cfg80211_stop_ap+0x60/0xf0 [cfg80211]
[<ffffffbffcdb6d08>] __cfg80211_leave+0x110/0x150 [cfg80211]
[<ffffffbffcdb6d78>] cfg80211_leave+0x30/0x48 [cfg80211]
[<ffffffbffcdb6fbc>] cfg80211_init_wdev+0x22c/0x808 [cfg80211]
[<ffffffc0000afe28>] notifier_call_chain+0x50/0x84
[<ffffffc0000afefc>] raw_notifier_call_chain+0x14/0x1c
[<ffffffc0004ae94c>] call_netdevice_notifiers_info+0x5c/0x6c
[<ffffffc0004ae96c>] call_netdevice_notifiers+0x10/0x18
[<ffffffc0004aea80>] __dev_close_many+0x54/0xc0
[<ffffffc0004aeb50>] dev_close_many+0x64/0xdc
[<ffffffc0004b0b70>] rollback_registered_many+0x138/0x2f4
[<ffffffc0004b0d4c>] rollback_registered+0x20/0x34
[<ffffffc0004b34b4>] unregister_netdevice_queue+0x68/0xa8
[<ffffffbffce3870c>] ieee80211_if_remove+0x84/0xc0 [mac80211]
[<ffffffbffce3e588>] ieee80211_nan_func_match+0x2374/0x23e4 [mac80211]
[<ffffffbffcdc29e8>] cfg80211_wext_giwscan+0x1000/0x1140 [cfg80211]
[<ffffffbffcb2a87c>] backport_genlmsg_multicast_allns+0x158/0x1b4 [compat]
[<ffffffc0004e0944>] genl_family_rcv_msg+0x258/0x2c0
[<ffffffc0004e09f4>] genl_rcv_msg+0x48/0x6c
[<ffffffc0004dfb50>] netlink_rcv_skb+0x5c/0xc4
[<ffffffc0004e06d8>] genl_rcv+0x34/0x48
[<ffffffc0004df570>] netlink_unicast+0x12c/0x1e0
[<ffffffc0004df9a4>] netlink_sendmsg+0x2bc/0x2dc
[<ffffffc00049a540>] sock_sendmsg+0x18/0x2c
[<ffffffc00049ab94>] ___sys_sendmsg+0x1bc/0x248
[<ffffffc00049ba24>] __sys_sendmsg+0x40/0x68
[<ffffffc00049ba5c>] SyS_sendmsg+0x10/0x20
[<ffffffc000085db0>] el0_svc_naked+0x24/0x28
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Parse and store the out-of-band rates reported by the FW.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will start using ieee80211_tx_status_ext() so we do not need to track
tx rates inside a struct ieee80211_tx_info. It is currently not possible
to populate that struct with HE rate info anyhow.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This makes the code consistent with the recent sc to ab rename.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update tx duration in station info form PPDU stats
so that users can dump tx duration of the station.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add basic HE support to the driver. The sband_iftype data is generated from
the capabilities read from the FW.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath11k is a new driver for Qualcomm IEEE 802.11ax devices, first
supporting only IPQ8074 SoC using the shared memory AHB bus. ath11k
uses mac80211 and supports AP, Station and Mesh modes.
Even though ath11k has some similar code as with ath10k (especially
the WMI layer) it was concluded to be simpler to have a "clean start"
for ath11k code base and not try to share the code with ath10k. This
makes maintenance easier and avoids major changes in ath10k, which
would have significantly increased the risk of regressions in existing
setups.
Even though the driver is very similar with ath10k but there are major
differences as well. The datapath is completely different. ath11k
supports multiple MACs, called "soc" in the firmware interface. And
there's only one WMI interface to support.
Currently ath11k supports only IEEE 802.11ac mode, but patches for
802.11ax are available and they will be submitted after ath11k is
accepted to upstream.
The firmware images are available from ath11k-firmware repository but
they will be also submitted to linux-firmware:
https://github.com/kvalo/ath11k-firmware
This was tested with firmware version WLAN.HK.2.1.0.1-00629-QCAHKSWPL_SILICONZ-1.
The driver has had multiple authors who are listed in alphabetical
order below.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Ganesh Sesetti <gseset@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
