This corrected patch adds machine independent line discipline code, prevoiusly
exsiting inside my Amstrad Delta ASoC machine dirver, to the Conexant CX20442
codec driver. The code can be used as a standalone line discipline, or as a
set of codec specific functions called from machine's line discipline
callbacks. Anyway, the line discipline itself must be registered by a machine
driver.
Applies on top of the followup to my initial driver version:
http://mailman.alsa-project.org/pipermail/alsa-devel/2009-July/019757.html
Suggested by ASoC manintainer Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
1. fix "line over 80 characters" checkpatch warnings
2. ‘DMA_nnBIT_MASK’ is deprecated, use DMA_BIT_MASK instead
3. fix typos
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The patch fixes some checkpatch identified issues and adds a comment about
line discipline interaction to my driver code, as requested by Mark on my
inital submission (thank you Mark for applying my imperfect patch anyway).
It also fixes MODULE_ALIAS mismatch as used in my machine driver.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAX9877 needs an address of start register when we write values to
registers through i2c_master_send(), but the code for this was missed in
max9877_write_regs().
If the value of control is 0 in the max9877_set_out_mode(), the value is
not increased to 1, but actually the value to write to the register
should be 1.
And the register bits for out_mode and osc_mode should be cleared before
writing.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Conexant CX20442-11 voice modem codec, suitable
for use by the ASoC board driver for Amstrad E3 (Delta) videophone. Related
sound card driver will follow.
This codec is an optional part of the Conexant SmartV three chip modem design.
As such, documentation for its proprietary digital audio interface is not
available. However, on Amstrad Delta board, thanks to Mark Underwood who
created an initial, omap-alsa based sound driver a few years ago[1], the codec
has been discovered to be accessible not only from the modem side, but also
over the OMAP McBSP based CPU DAI. Thus, the driver can be used by any sound
card that can access the codec DAI directly. The DAI configuration parameters
(sample rate and format, number of channels) has been selected out empirically
for best user experience.
The codec analogue interface consists of two pairs of analogue I/O pins:
speakerphone interface or telephone handset/headset interface. Furthermore, it
seams to provide two operation modes for speakerphone I/O: standard and
advanced, with automatic gain control and echo cancelation. Even if the codec
control interface is unknown and not available, all those interfaces and modes
can be selected over the modem chip using V.253 commands. The driver is able
to issue necessary commands over a suitable hw_write function if provided by a
sound card driver. Otherwise, the codec can be controlled over the modem from
userspace while inactive.
Even if nothig is known about the codec internal power management
capabilities, DAPM widgets has been used to model the codec audio map.
Automatically performed powering up/down of those virtual widgets results in
corresponding V.253 commands being issued.
Some driver features/oddities may be board specific, but I have no way to
verify that with any board other than Amstrad Delta.
[1] http://www.earth.li/pipermail/e3-hacking/2006-April/000481.html
Created and tested against linux-2.6.31-rc3.
Applies and works with linux-omap-2.6 commit
7c5cb7862d32cb344be7831d466535d5255e35ac as well.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
PLL was not being enabled when it was not bypassed. This patch
enables the PLL when it is used. Additionally, it disables the PLL
when it is bypassed.
Without this patch, the audio on TI DM646x EVM and DM355 EVM
does not work properly. The bit clocks and the frame sync signals
from the codec are not correct and hence the playback/record are faster
than usual for most sample rates. The reason for this was that the PLL
was not enabled when it was not bypassed.
Tested on DM6467 EVM, playback tested on DM355 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The callback function to control register was used by whole controls in
MAX9877 driver, but this causes using many if statement for double
register control or invert.
So, the callback function for double register control is separate
differently, and the code for invert is added in the callback function.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This corrects a bug with ADC Inversion Switch in wm8974 codec.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
GCC 4.4.0 doesn't appear to be able to spot that we don't apply any FLL
configuration if the output frequency is zero.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAX9877 combines a high-efficiency Class D audio power amplifier
with a stereo Class AB capacitor-less DirectDrive headphone amplifier.
The max9877_add_controls() is called to register the MAX9877 specific
controls on machine specific init() of the machine driver.
The datasheet for the MAX9877 can find at the following url:
http://datasheets.maxim-ic.com/en/ds/MAX9877.pdf
[Slight edit to sort the ALL_CODECS entries -- broonie.]
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Due to the flexibility of the WM9081 FLL this should never happen
in a real system.
Reported-by: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to use the best value we picked, not the last value we
looked at.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Without MODULE_LICENCE("GPL"), when built as a module it will fail
to load because it uses other GPL symbols from kernel.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the last in-kernel direct usage of driver_data, replace it with
the proper dev_get/set_drvdata() calls.
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jaroslav Kysela <perex@perex.cz>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While the hardware is capable of some limited asynmmetric modes the
driver does not currently support those modes so tell applications
that only symmetric rates are available.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8993 is a highly integrated ultra-low power hi-fi CODEC designed
for portable devices such as multimedia phones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Note the slightly tricky cache usage in the volume update function due
to the requirement for a separate write for the VU bit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The TLV320AIC3x driver is currently the only user of the CODEC hw_read
operation and is jumping through some hoops in order to do so. In order
to support future refactoring to make the hw_read operation more usable
unwrap the usage in this driver to avoid its use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Nothing uses it and the existing hw_read operation needs to be
refectored so it's easier to remove it rather than work with it.
Support can be re-added if the code requires volatile registers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A lot of CODECs share the same register data formats and therefore
replicate the code to manage access to and caching of the register
map. In order to reduce code duplication centralised versions of
this code will be introduced with drivers able to configure the use
of the common code by calling the new snd_soc_codec_set_cache_io()
API call during startup.
As an initial user the 7 bit address/9 bit data format used by many
Wolfson devices is supported for write only CODECs and the drivers
with straightforward register cache implementations are converted to
use it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Register cache space was not being allocated for the final register,
causing bugs when it was used. Allocate space for it.
Also ensure that the final register is displayed in sysfs.
[Commit message rewritten to document actual issue. -- broonie]
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add "set_tristate" callbacks for HiFi and Voice DAIs.
Machine drivers can enable and disable tristate for each
DAI with "snd_soc_dai_set_tristate" function.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The wrong register cache variable was being used to provide the size for
the memcpy(), resulting in a copy of only a void * of data.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
According to TRM, an external FET controlled by a 1.8V output signal
can be used to reduce the pop-noise heard when the audio amplifier is
switched on. It is suggested that GPIO6 of TWL4030 be used, but any
other gpio can be used instead. This is indicated in machine driver
with the following twl4030_setup_data members:
-hs_extmute. Set to 1 if board has support for EXTMUTE.
-set_hs_extmute. Set to a callback funcion to control an external gpio
line. Set to NULL if MUTE[GPIO6] pin is used.
Codec driver takes care of enabling and disabling this output during
the headset pop attenuation sequence.
Also add a delay to let VMID settle in ramp up sequence.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8523 is a high performance stereo DAC with integral charge
pump providing 2Vrms line driver outputs using a single 3.3V power
supply rail.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The device is a mono device but it can read two channel data and
many I2S controllers only understand 2 channels.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
