Commit 77acc6b55a ("riscv: add support for kernel-mode FPU") and
commit a28e4b672f ("drm/amd/display: use ARCH_HAS_KERNEL_FPU_SUPPORT")
enabled support for CONFIG_DRM_AMD_DC_FP with RISC-V. Unfortunately,
this exposed -Wframe-larger-than warnings (which become fatal with
CONFIG_WERROR=y) when building ARCH=riscv allmodconfig with clang:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn32/display_mode_vba_32.c:58:13: error: stack frame size (2448) exceeds limit (2048) in 'DISPCLKDPPCLKDCFCLKDeepSleepPrefetchParametersWatermarksAndPerformanceCalculation' [-Werror,-Wframe-larger-than]
58 | static void DISPCLKDPPCLKDCFCLKDeepSleepPrefetchParametersWatermarksAndPerformanceCalculation(
| ^
1 error generated.
Many functions in this file use a large number of parameters, which must
be passed on the stack at a certain pointer due to register exhaustion,
which can cause high stack usage when inlining and issues with stack
slot analysis get involved. While the compiler can and should do better
(as GCC uses less than half the amount of stack space for the same
function), it is not as simple as a fix as adjusting the functions not
to take a large number of parameters.
Unfortunately, modifying these files to avoid the problem is a difficult
to justify approach because any revisions to the files in the kernel
tree never make it back to the original source (so copies of the code
for newer hardware revisions just reintroduce the issue) and the files
are hard to read/modify due to being "gcc-parsable HW gospel, coming
straight from HW engineers".
Avoid building the problematic code for RISC-V by modifying the existing
condition for arm64 that exists for the same reason. Factor out the
logical not to make the condition a little more readable naturally.
Fixes: a28e4b672f ("drm/amd/display: use ARCH_HAS_KERNEL_FPU_SUPPORT")
Reported-by: Palmer Dabbelt <palmer@rivosinc.com>
Closes: https://lore.kernel.org/20240530145741.7506-2-palmer@rivosinc.com/
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Empty SST TUs are illegal to transmit over a USB4 DP tunnel.
Current policy is to configure stream encoder to pack 2 pixels per pclk
even when ODM combine is not in use, allowing seamless dynamic ODM
reconfiguration. However, in extreme edge cases where average pixel
count per TU is less than 2, this can lead to unexpected empty TU
generation during compliance testing. For example, VIC 1 with a 1xHBR3
link configuration will average 1.98 pix/TU.
[HOW]
Calculate average pixel count per TU, and block 2 pixels per clock if
endpoint is a DPIA tunnel and pixel clock is low enough that we will
never require 2:1 ODM combine.
Cc: stable@vger.kernel.org # 6.6+
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Current DRAM setting would cause underflow on customer platform.
Modify dram_clock_change_latency_us from 11.72 to 34.0 us as per recommendation from HW team
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Intermittent underflow observed when using 4k144 display on
dcn351
[How]
Update dram_clock_change_latency_us from 11.72us to 34us
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can't read/write to DCN registers while in IPS. Since, that can cause
the system to hang. So, before proceeding with the access in that
scenario, force the system out of IPS.
Cc: stable@vger.kernel.org # 6.6+
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Disable idle optimization for each atomic commit is unnecessary,
and can lead to a potential race condition.
[How]
Remove idle optimization check from amdgpu_dm_atomic_commit_tail()
Fixes: 196107eb1e ("drm/amd/display: Add IPS checks before dcn register access")
Cc: stable@vger.kernel.org
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
nouveau:
- fix bo metadata uAPI for vm bind
panthor:
- Fixes for panthor's heap logical block.
- Reset on unrecoverable fault
- Fix VM references.
- Reset fix.
xlnx:
- xlnx compile and doc fixes.
amdgpu:
- Handle vbios table integrated info v2.3
amdkfd:
- Handle duplicate BOs in reserve_bo_and_cond_vms
- Handle memory limitations on small APUs
dp/mst:
- MST null deref fix.
bridge:
- Don't let next bridge create connector in adv7511 to make probe work.
-----BEGIN PGP SIGNATURE-----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=pexB
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2024-05-25' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Some fixes for the end of the merge window, mostly amdgpu and panthor,
with one nouveau uAPI change that fixes a bad decision we made a few
months back.
nouveau:
- fix bo metadata uAPI for vm bind
panthor:
- Fixes for panthor's heap logical block.
- Reset on unrecoverable fault
- Fix VM references.
- Reset fix.
xlnx:
- xlnx compile and doc fixes.
amdgpu:
- Handle vbios table integrated info v2.3
amdkfd:
- Handle duplicate BOs in reserve_bo_and_cond_vms
- Handle memory limitations on small APUs
dp/mst:
- MST null deref fix.
bridge:
- Don't let next bridge create connector in adv7511 to make probe
work"
* tag 'drm-next-2024-05-25' of https://gitlab.freedesktop.org/drm/kernel:
drm/amdgpu/atomfirmware: add intergrated info v2.3 table
drm/mst: Fix NULL pointer dereference at drm_dp_add_payload_part2
drm/amdkfd: Let VRAM allocations go to GTT domain on small APUs
drm/amdkfd: handle duplicate BOs in reserve_bo_and_cond_vms
drm/bridge: adv7511: Attach next bridge without creating connector
drm/buddy: Fix the warn on's during force merge
drm/nouveau: use tile_mode and pte_kind for VM_BIND bo allocations
drm/panthor: Call panthor_sched_post_reset() even if the reset failed
drm/panthor: Reset the FW VM to NULL on unplug
drm/panthor: Keep a ref to the VM at the panthor_kernel_bo level
drm/panthor: Force an immediate reset on unrecoverable faults
drm/panthor: Document drm_panthor_tiler_heap_destroy::handle validity constraints
drm/panthor: Fix an off-by-one in the heap context retrieval logic
drm/panthor: Relax the constraints on the tiler chunk size
drm/panthor: Make sure the tiler initial/max chunks are consistent
drm/panthor: Fix tiler OOM handling to allow incremental rendering
drm: xlnx: zynqmp_dpsub: Fix compilation error
drm: xlnx: zynqmp_dpsub: Fix few function comments
MST colorspace property support was disabled due to a series of warnings
that came up when the device was plugged in since the properties weren't
made at device creation. Create the properties in advance instead.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 69a9596102 ("drm/amd/display: Temporary Disable MST DP Colorspace Property").
Reported-and-tested-by: Tyler Schneider <tyler.schneider@amd.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3353
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The __assign_str() macro logic of the TRACE_EVENT() macro was optimized so
that it no longer needs the second argument. The __assign_str() is always
matched with __string() field that takes a field name and the source for
that field:
__string(field, source)
The TRACE_EVENT() macro logic will save off the source value and then use
that value to copy into the ring buffer via the __assign_str(). Before
commit c1fa617cae ("tracing: Rework __assign_str() and __string() to not
duplicate getting the string"), the __assign_str() needed the second
argument which would perform the same logic as the __string() source
parameter did. Not only would this add overhead, but it was error prone as
if the __assign_str() source produced something different, it may not have
allocated enough for the string in the ring buffer (as the __string()
source was used to determine how much to allocate)
Now that the __assign_str() just uses the same string that was used in
__string() it no longer needs the source parameter. It can now be removed.
-----BEGIN PGP SIGNATURE-----
iIkEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCZk9RMBQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qur+AP9jbSYaGhzZdJ7a3HGA8M4l6JNju8nC
GcX1JpJT4z1qvgD3RkoNvP87etDAUAqmbVhVWnUHCY/vTqr9uB/gqmG6Ag==
=Y+6f
-----END PGP SIGNATURE-----
Merge tag 'trace-assign-str-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing cleanup from Steven Rostedt:
"Remove second argument of __assign_str()
The __assign_str() macro logic of the TRACE_EVENT() macro was
optimized so that it no longer needs the second argument. The
__assign_str() is always matched with __string() field that takes a
field name and the source for that field:
__string(field, source)
The TRACE_EVENT() macro logic will save off the source value and then
use that value to copy into the ring buffer via the __assign_str().
Before commit c1fa617cae ("tracing: Rework __assign_str() and
__string() to not duplicate getting the string"), the __assign_str()
needed the second argument which would perform the same logic as the
__string() source parameter did. Not only would this add overhead, but
it was error prone as if the __assign_str() source produced something
different, it may not have allocated enough for the string in the ring
buffer (as the __string() source was used to determine how much to
allocate)
Now that the __assign_str() just uses the same string that was used in
__string() it no longer needs the source parameter. It can now be
removed"
* tag 'trace-assign-str-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/treewide: Remove second parameter of __assign_str()
With the rework of how the __string() handles dynamic strings where it
saves off the source string in field in the helper structure[1], the
assignment of that value to the trace event field is stored in the helper
value and does not need to be passed in again.
This means that with:
__string(field, mystring)
Which use to be assigned with __assign_str(field, mystring), no longer
needs the second parameter and it is unused. With this, __assign_str()
will now only get a single parameter.
There's over 700 users of __assign_str() and because coccinelle does not
handle the TRACE_EVENT() macro I ended up using the following sed script:
git grep -l __assign_str | while read a ; do
sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file;
mv /tmp/test-file $a;
done
I then searched for __assign_str() that did not end with ';' as those
were multi line assignments that the sed script above would fail to catch.
Note, the same updates will need to be done for:
__assign_str_len()
__assign_rel_str()
__assign_rel_str_len()
I tested this with both an allmodconfig and an allyesconfig (build only for both).
[1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/
Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts.
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs
Tested-by: Guenter Roeck <linux@roeck-us.net>
Now that all previously-supported architectures select
ARCH_HAS_KERNEL_FPU_SUPPORT, this code can depend on that symbol instead
of the existing list of architectures. It can also take advantage of the
common kernel-mode FPU API and method of adjusting CFLAGS.
Link: https://lkml.kernel.org/r/20240329072441.591471-14-samuel.holland@sifive.com
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian König <christian.koenig@amd.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nicolas Schier <nicolas@fjasle.eu>
Cc: Palmer Dabbelt <palmer@rivosinc.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: WANG Xuerui <git@xen0n.name>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The compiler flags enable altivec, but that is not required; hard-float is
sufficient for the code to build and function.
Drop altivec from the compiler flags and adjust the enable/disable code to
only enable FPU use.
Link: https://lkml.kernel.org/r/20240329072441.591471-13-samuel.holland@sifive.com
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nicolas Schier <nicolas@fjasle.eu>
Cc: Palmer Dabbelt <palmer@rivosinc.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: WANG Xuerui <git@xen0n.name>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
new drivers:
- panthor: ARM Mali/Immortalis CSF-based GPU driver
core:
- add a CONFIG_DRM_WERROR option
- make more headers self-contained
- grab resv lock in pin/unpin
- fix vmap resv locking
- EDID/eDP panel matching
- Kconfig cleanups
- DT sound bindings
- Add SIZE_HINTS property for cursor planes
- Add struct drm_edid_product_id and helpers.
- Use drm device based logging in more drm functions.
- drop seq_file.h from a bunch of places
- use drm_edid driver conversions
dp:
- DP Tunnel documentation
- MST read sideband cap
- Adaptive sync SDP prep work
ttm:
- improve placement for TTM BOs in idle/busy handling
panic:
- Fixes for drm-panic, and option to test it.
- Add drm panic to simpledrm, mgag200, imx, ast
bridge:
- improve init ordering
- adv7511: allow GPIO pin sharing
- tc358775: add tc358675 support
panel:
- AUO B120XAN01.0
- Samsung s6e3fa7
- BOE NT116WHM-N44
- CMN N116BCA-EA1,
- CrystalClear CMT430B19N00
- Startek KD050HDFIA020-C020A
- powertip PH128800T006-ZHC01
- Innolux G121X1-L03
- LG sw43408
- Khadas TS050 V2
- EDO RM69380 OLED
- CSOT MNB601LS1-1
amdgpu:
- HDCP/ODM/RAS fixes
- Devcoredump improvements
- Expose VCN activity via sysfs
- SMY 13.0.x updates
- Enable fast updates on DCN 3.1.4
- Add dclk and vclk reporting on additional devices
- Add ACA RAS infrastructure
- Implement TLB flush fence
- EEPROM handling fixes
- SMUIO 14.0.2 support
- SMU 14.0.1 Updates
- SMU 14.0.2 support
- Sync page table freeing with TLB flushes
- DML2 refactor
- DC debug improvements
- DCN 3.5.x Updates
- GPU reset fixes
- HDP fix for second GFX pipe on GC 10.x
- Enable secondary GFX pipe on GC 10.3
- Refactor and clean up BACO/BOCO/BAMACO handling
- Remove invalid TTM resource start check
- UAF fix in VA IOCTL
- GPUVM page fault redirection to secondary IH rings for IH 6.x
- Initial support for mapping kernel queues via MES
- Fix VRAM memory accounting
amdkfd:
- MQD handling cleanup
- Preemption handling fixes for XCDs
- TLB flush fix for GC 9.4.2
- Properly clean up workqueue during module unload
- Fix memory leak process create failure
- Range check CP bad op exception targets to avoid reporting invalid exceptions to userspace
- Fix eviction fence handling
- Fix leak in GPU memory allocation failure case
- DMABuf import handling fix
- Enable SQ watchpoint for gfx10
i915:
- Adding new DG2 PCI ID
- add context hints for GT frequency
- enable only one CCS for compute workloads
- new workarounds
- Fix UAF on destroy against retire race and remove two earlier partial fixes
- Limit the reserved VM space to only the platforms that need it
- Fix gt reset with GuC submission is disable
- Add and use gt_to_guc() wrapper
i915/xe display:
- Lunar Lake display enabling, including cdclk and other refactors
- BIOS/VBT/opregion related refactor
- Digital port related refactor/clean-up
- Fix 2s boot time regression on DP panel replay init
- Remove duplication on audio enable/disable on SDVO and g4x+ DP
- Disable AuxCCS framebuffers if built for Xe
- Make crtc disable more atomic
- Increase DP idle pattern wait timeout to 2ms
- Start using container_of_const() for some extra const safety
- Fix Jasper Lake boot freeze
- Enable MST mode for 128b/132b single-stream sideband
- Enable Adaptive Sync SDP Support for DP
- Fix MTL supported DP rates - removal of UHBR13.5
- PLL refactoring
- Limit eDP MSO pipe only for display version 20
- More display refactor towards independence from i915 dev_priv
- Convert i915/xe fbdev to DRM client
- More initial work to make display code more independent from i915
xe:
- improved error capture
- clean up some uAPI leftovers
- devcoredump update
- Add BMG mocs table
- Handle GSCCS ER interrupt
- Implement xe2- and GuC workarounds
- struct xe_device cleanup
- Hwmon updates
- Add LRC parsing for more GPU instruction
- Increase VM_BIND number of per-ioctl Ops
- drm/xe: Add XE_BO_GGTT_INVALIDATE flag
- Initial development for SR-IOV support
- Add new PCI IDs to DG2 platform
- Move userptr over to start using hmm_range_fault
msm:
- Switched to generating register header files during build process
instead of shipping pre-generated headers
- Merged DPU and MDP4 format databases.
- DP:
- Stop using compat string to distinguish DP and eDP cases
- Added support for X Elite platform (X1E80100)
- Reworked DP aux/audio support
- Added SM6350 DP to the bindings
- GPU:
- a7xx perfcntr reg fixes
- MAINTAINERS updates
- a750 devcoredump support
radeon:
- Silence UBSAN warnings related to flexible arrays
nouveau:
- move some uAPI objects to uapi headers
omapdrm:
- console fix
ast:
- add i2c polling
qaic:
- add debugfs entries
exynos:
- fix platform_driver .owner
- drop cleanup code
mediatek:
- Use devm_platform_get_and_ioremap_resource() in mtk_hdmi_ddc_probe()
- Add GAMMA 12-bit LUT support for MT8188
- Rename mtk_drm_* to mtk_*
- Drop driver owner initialization
- Correct calculation formula of PHY Timing
-----BEGIN PGP SIGNATURE-----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=ocVM
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2024-05-15' of https://gitlab.freedesktop.org/drm/kernel
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm subsystems for 6.10.
In drivers the main thing is a new driver for ARM Mali firmware based
GPUs, otherwise there are a lot of changes to amdgpu/xe/i915/msm and
scattered changes to everything else.
In the core a bunch of headers and Kconfig was refactored, along with
the addition of a new panic handler which is meant to provide a user
friendly message when a panic happens and graphical display is
enabled.
New drivers:
- panthor: ARM Mali/Immortalis CSF-based GPU driver
Core:
- add a CONFIG_DRM_WERROR option
- make more headers self-contained
- grab resv lock in pin/unpin
- fix vmap resv locking
- EDID/eDP panel matching
- Kconfig cleanups
- DT sound bindings
- Add SIZE_HINTS property for cursor planes
- Add struct drm_edid_product_id and helpers.
- Use drm device based logging in more drm functions.
- drop seq_file.h from a bunch of places
- use drm_edid driver conversions
dp:
- DP Tunnel documentation
- MST read sideband cap
- Adaptive sync SDP prep work
ttm:
- improve placement for TTM BOs in idle/busy handling
panic:
- Fixes for drm-panic, and option to test it.
- Add drm panic to simpledrm, mgag200, imx, ast
bridge:
- improve init ordering
- adv7511: allow GPIO pin sharing
- tc358775: add tc358675 support
panel:
- AUO B120XAN01.0
- Samsung s6e3fa7
- BOE NT116WHM-N44
- CMN N116BCA-EA1,
- CrystalClear CMT430B19N00
- Startek KD050HDFIA020-C020A
- powertip PH128800T006-ZHC01
- Innolux G121X1-L03
- LG sw43408
- Khadas TS050 V2
- EDO RM69380 OLED
- CSOT MNB601LS1-1
amdgpu:
- HDCP/ODM/RAS fixes
- Devcoredump improvements
- Expose VCN activity via sysfs
- SMY 13.0.x updates
- Enable fast updates on DCN 3.1.4
- Add dclk and vclk reporting on additional devices
- Add ACA RAS infrastructure
- Implement TLB flush fence
- EEPROM handling fixes
- SMUIO 14.0.2 support
- SMU 14.0.1 Updates
- SMU 14.0.2 support
- Sync page table freeing with TLB flushes
- DML2 refactor
- DC debug improvements
- DCN 3.5.x Updates
- GPU reset fixes
- HDP fix for second GFX pipe on GC 10.x
- Enable secondary GFX pipe on GC 10.3
- Refactor and clean up BACO/BOCO/BAMACO handling
- Remove invalid TTM resource start check
- UAF fix in VA IOCTL
- GPUVM page fault redirection to secondary IH rings for IH 6.x
- Initial support for mapping kernel queues via MES
- Fix VRAM memory accounting
amdkfd:
- MQD handling cleanup
- Preemption handling fixes for XCDs
- TLB flush fix for GC 9.4.2
- Properly clean up workqueue during module unload
- Fix memory leak process create failure
- Range check CP bad op exception targets to avoid reporting invalid exceptions to userspace
- Fix eviction fence handling
- Fix leak in GPU memory allocation failure case
- DMABuf import handling fix
- Enable SQ watchpoint for gfx10
i915:
- Adding new DG2 PCI ID
- add context hints for GT frequency
- enable only one CCS for compute workloads
- new workarounds
- Fix UAF on destroy against retire race and remove two earlier partial fixes
- Limit the reserved VM space to only the platforms that need it
- Fix gt reset with GuC submission is disable
- Add and use gt_to_guc() wrapper
i915/xe display:
- Lunar Lake display enabling, including cdclk and other refactors
- BIOS/VBT/opregion related refactor
- Digital port related refactor/clean-up
- Fix 2s boot time regression on DP panel replay init
- Remove duplication on audio enable/disable on SDVO and g4x+ DP
- Disable AuxCCS framebuffers if built for Xe
- Make crtc disable more atomic
- Increase DP idle pattern wait timeout to 2ms
- Start using container_of_const() for some extra const safety
- Fix Jasper Lake boot freeze
- Enable MST mode for 128b/132b single-stream sideband
- Enable Adaptive Sync SDP Support for DP
- Fix MTL supported DP rates - removal of UHBR13.5
- PLL refactoring
- Limit eDP MSO pipe only for display version 20
- More display refactor towards independence from i915 dev_priv
- Convert i915/xe fbdev to DRM client
- More initial work to make display code more independent from i915
xe:
- improved error capture
- clean up some uAPI leftovers
- devcoredump update
- Add BMG mocs table
- Handle GSCCS ER interrupt
- Implement xe2- and GuC workarounds
- struct xe_device cleanup
- Hwmon updates
- Add LRC parsing for more GPU instruction
- Increase VM_BIND number of per-ioctl Ops
- drm/xe: Add XE_BO_GGTT_INVALIDATE flag
- Initial development for SR-IOV support
- Add new PCI IDs to DG2 platform
- Move userptr over to start using hmm_range_fault
msm:
- Switched to generating register header files during build process
instead of shipping pre-generated headers
- Merged DPU and MDP4 format databases.
- DP:
- Stop using compat string to distinguish DP and eDP cases
- Added support for X Elite platform (X1E80100)
- Reworked DP aux/audio support
- Added SM6350 DP to the bindings
- GPU:
- a7xx perfcntr reg fixes
- MAINTAINERS updates
- a750 devcoredump support
radeon:
- Silence UBSAN warnings related to flexible arrays
nouveau:
- move some uAPI objects to uapi headers
omapdrm:
- console fix
ast:
- add i2c polling
qaic:
- add debugfs entries
exynos:
- fix platform_driver .owner
- drop cleanup code
mediatek:
- Use devm_platform_get_and_ioremap_resource() in mtk_hdmi_ddc_probe()
- Add GAMMA 12-bit LUT support for MT8188
- Rename mtk_drm_* to mtk_*
- Drop driver owner initialization
- Correct calculation formula of PHY Timing"
* tag 'drm-next-2024-05-15' of https://gitlab.freedesktop.org/drm/kernel: (1477 commits)
drm/xe/ads: Use flexible-array
drm/xe: Use ordered WQ for G2H handler
drm/msm/gen_header: allow skipping the validation
drm/msm/a6xx: Cleanup indexed regs const'ness
drm/msm: Add devcoredump support for a750
drm/msm: Adjust a7xx GBIF debugbus dumping
drm/msm: Update a6xx registers XML
drm/msm: Fix imported a750 snapshot header for upstream
drm/msm: Import a750 snapshot registers from kgsl
MAINTAINERS: Add Konrad Dybcio as a reviewer for the Adreno driver
MAINTAINERS: Add a separate entry for Qualcomm Adreno GPU drivers
drm/msm/a6xx: Avoid a nullptr dereference when speedbin setting fails
drm/msm/adreno: fix CP cycles stat retrieval on a7xx
drm/msm/a7xx: allow writing to CP_BV counter selection registers
drm: zynqmp_dpsub: Always register bridge
Revert "drm/bridge: ti-sn65dsi83: Fix enable error path"
drm/fb_dma: Add checks in drm_fb_dma_get_scanout_buffer()
drm/fbdev-generic: Do not set physical framebuffer address
drm/panthor: Fix the FW reset logic
drm/panthor: Make sure we handle 'unknown group state' case properly
...
[Why]
Some older MST hubs do not report DPCD registers according to
specification.
[How]
This change re-applies commit c536555451 ("drm/amd/display: dsc mst
re-compute pbn for changes on hub").
With an additional check for these older MST devices.
Reviewed-by: Swapnil Patel <swapnil.patel@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Idle optimizations are blocked if there's more than one eDP connector
on the board - blocking S0i3 and IPS2 for static screen.
[How]
Fix the checks to correctly detect number of active eDP.
Also restrict the eDP support to panels that have correct feature
support.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This fixes a bug introduced by commit c536555451 ("drm/amd/display: dsc
mst re-compute pbn for changes on hub").
The change caused light-up issues with a second display that required
DSC on some MST docks.
[How]
Use Virtual DPCD for DSC caps in MST case.
[Limitations]
This change only affects MST DSC devices that follow specifications
additional changes are required to check for old MST DSC devices such as
ones which do not check for Virtual DPCD registers.
Reviewed-by: Swapnil Patel <swapnil.patel@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow occurs when running Netflix in a 4k144 eDP + 4k60 HDMI FRL
setup. It is caused by latency varying based on the DCFCLK/FCLK state.
[How]
Enable urgent latency adjustment and match the reference to existing
ASIC that also see increased latency at low FCLK.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Panel replay was enabled by default in commit 5950efe25e
("drm/amd/display: Enable Panel Replay for static screen use case"), but
it isn't working properly at least on some BOE and AUO panels. Instead
of being static the screen is solid black when active. As it's a new
feature that was just introduced that regressed VRR disable it for now
so that problem can be properly root caused.
Cc: Tom Chung <chiahsuan.chung@amd.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3344
Fixes: 5950efe25e ("drm/amd/display: Enable Panel Replay for static screen use case")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
preOS will not support display mode programming and link training
for UHBR rates.
[how]
If we detect a sink that's UHBR capable, disable seamless boot
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Sung Joon Kim <sungjoon.kim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why && How]
Screen flickering saw on 4K@60 eDP with high refresh rate external
monitor when booting up in DC mode. DC Mode Capping is disabled
which caused wrong UCLK being used.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Leo Ma <hanghong.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add VCO speed parameters in the bounding box array.
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During DP tunnel creation, CM preallocates BW and reduces
estimated BW of other DPIA. CM release preallocation only
when allocation is complete. Display mode validation logic
validates timings based on bw available per host router.
In multi display setup, this causes bw allocation failure
when allocation greater than estimated bw.
[How]
Do zero alloc to make the CM to release preallocation and
update estimated BW correctly for all DPIAs per host router.
Reviewed-by: PeiChen Huang <peichen.huang@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] DSC debugfs, such as dp_dsc_clock_en_read,
use aconnector->dc_link to find pipe_ctx for display.
Displays connected to MST hub share the same dc_link.
DSC instance is from pipe_ctx. This causes incorrect
DSC instance for display connected to MST hub.
[How] Add aconnector->sink check to find pipe_ctx.
CC: stable@vger.kernel.org
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New request from KMD/VBIOS in order to support new UMA carveout
model. This fixes a null dereference from accessing
Ctx->dc_bios->integrated_info while it was NULL.
DAL parses through the BIOS and extracts the necessary
integrated_info but was missing a case for the new BIOS
version 2.3.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Currently DCN315 clk manager is missing code to enable/disable dtbclk.
Because of this, "optimized_required" flag is constantly set
and this prevents FreeSync from engaging for certain high bandwidth
display Modes which require DTBCLK.
Reviewed-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Swapnil Patel <swapnil.patel@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In the DCN20 resource initialization, ensure that DMCUB support starts
configured as true.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Theoretically rare corner case where ceil(Y) results in rounding up to
an integer. If this happens, the 1 should be carried over to the X
value.
CC: stable@vger.kernel.org
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add some missing HDCP registers to be used in DCN35.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit address some small code style issues in DC.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit reorganizes the order in which some control registers are
presented to make it easier to identify the operations based on the
hardware doc.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit removes some unnecessary code and makes the required
adjustments to replace other parts of the code with a short option.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes 29 UNINIT issues reported by Coverity.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes 49 UNINIT issues reported by Coverity.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes 11 UNINIT issues reported by Coverity.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes 1 PW.INCLUDE_RECURSION reported by Coverity.
"./drivers/gpu/drm/amd/amdgpu/../display/dc/dc_types.h"
includes itself: dc_types.h -> dal_types.h -> dc_types.h
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
find_disp_cfg_idx_by_plane_id and find_disp_cfg_idx_by_stream_id returns
an array index and they return -1 when not found; however, -1 is not a
valid index number.
[HOW]
When this happens, call ASSERT(), and return a positive number (which is
fewer than callers' array size) instead.
This fixes 4 OVERRUN and 2 NEGATIVE_RETURNS issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
resource_stream_to_stream_idx returns an array index and it return -1
when not found; however, -1 is not a valid array index number.
[HOW]
When this happens, call ASSERT(), and return a zero instead.
This fixes an OVERRUN and an NEGATIVE_RETURNS issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
&mode_lib->mp.Watermark and &locals->Watermark are
the same address. memcpy may lead to unexpected behavior.
[HOW]
memmove should be used.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
ENGINE_ID_UNKNOWN = -1 and can not be used as an array index. Plus, it
also means it is uninitialized and does not need free audio.
[HOW]
Skip and return NULL.
This fixes 2 OVERRUN issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pipe_ctx has a size of MAX_PIPES so checking its index before accessing
the array.
This fixes an OVERRUN issue reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
msg_id is used as an array index and it cannot be a negative value, and
therefore cannot be equal to MOD_HDCP_MESSAGE_ID_INVALID (-1).
[HOW]
Check whether msg_id is valid before reading and setting.
This fixes 4 OVERRUN issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Check return pointer of kzalloc before using it.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Theoretically rare corner case where ceil(Y) results in rounding up to
an integer. If this happens, the 1 should be carried over to the X
value.
CC: stable@vger.kernel.org
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Headless dp 2.0 will take longer to update.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit add some missing HDMI control registers to DCN3x.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add TMDS balancer control to the list of available encoder registers for
DCN 30.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit removes an unnecessary NULL check in the
`dcn20_set_input_transfer_func` function in the `dcn20_hwseq.c` file.
The variable `tf` is assigned the address of
`plane_state->in_transfer_func` unconditionally, so it can never be
`NULL`. Therefore, the check `if (tf == NULL)` is unnecessary and has
been removed.
The plane_state->in_transfer_func itself cannot be NULL because it's a
structure, not a pointer. When we do tf =
&plane_state->in_transfer_func;, we're getting the address of that
structure, which will always be valid as long as plane_state itself is
not NULL.
we've already checked if plane_state is NULL with the line if (dpp_base
== NULL || plane_state == NULL) return false;. So, if the code execution
gets to the point where tf = &plane_state->in_transfer_func; is called,
plane_state is guaranteed to be not NULL, and therefore tf will also not
be NULL.
drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn20/dcn20_hwseq.c
1094 bool dcn20_set_input_transfer_func(struct dc *dc,
1095 struct pipe_ctx *pipe_ctx,
1096 const struct dc_plane_state *plane_state)
1097 {
1098 struct dce_hwseq *hws = dc->hwseq;
1099 struct dpp *dpp_base = pipe_ctx->plane_res.dpp;
1100 const struct dc_transfer_func *tf = NULL;
^^^^^^^^^ This assignment is not necessary now.
1101 bool result = true;
1102 bool use_degamma_ram = false;
1103
1104 if (dpp_base == NULL || plane_state == NULL)
1105 return false;
1106
1107 hws->funcs.set_shaper_3dlut(pipe_ctx, plane_state);
1108 hws->funcs.set_blend_lut(pipe_ctx, plane_state);
1109
1110 tf = &plane_state->in_transfer_func;
^^^^^
Before there was an if statement but now tf is assigned unconditionally
1111
--> 1112 if (tf == NULL) {
^^^^^^^^^^^^^^^^^
so these conditions are impossible.
1113 dpp_base->funcs->dpp_set_degamma(dpp_base,
1114 IPP_DEGAMMA_MODE_BYPASS);
1115 return true;
1116 }
1117
1118 if (tf->type == TF_TYPE_HWPWL || tf->type == TF_TYPE_DISTRIBUTED_POINTS)
1119 use_degamma_ram = true;
1120
1121 if (use_degamma_ram == true) {
1122 if (tf->type == TF_TYPE_HWPWL)
1123 dpp_base->funcs->dpp_program_degamma_pwl(dpp_base,
Fixes the below Smatch static checker warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn20/dcn20_hwseq.c:1112 dcn20_set_input_transfer_func() warn: address of 'plane_state->in_transfer_func' is non-NULL
Fixes: 285a7054bf ("drm/amd/display: Remove plane and stream pointers from dc scratch")
Cc: Wenjing Liu <wenjing.liu@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Alvin Lee <alvin.lee2@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Suggested-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN3.0 supports some specific DWB debug registers that are not exposed
yet. This commit just adds the missing registers.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
