DC version 3.2.211 brings along the following fixes:
- Wait for VBLANK during pipe programming
- Adding HDMI SCDC DEVICE_ID define
- Cursor update refactor: PSR-SU support condition
- Update 709 gamma to 2.222 as stated in the standerd
- Consider dp cable id only when data is non zero
- Waiting for 1 frame to fix the flash issue on PSR1
- Update SR watermarks for DCN314
- Allow tuning DCN314 bounding box
- Zeromem mypipe heap struct before using it
- Use min transition for SubVP into MPO
- Disable phantom OTG after enable for plane disable
- Disable DRR actions during state commit
- Fix fallback issues for DP LL 1.4a tests
- Fix FCLK deviation and tool compile issues
- Fix reg timeout in enc314_enable_fifo
- Fix gpio port mapping issue
- Only update link settings after successful MST link train
- Enforce minimum prefetch time for low memclk on DCN32
- Set correct EOTF and Gamut flag in VRR info
- Add margin for max vblank time for SubVP + DRR
- Populate DP2.0 output type for DML pipe
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Reviewed-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Aric Cyr <Aric.Cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Incorporate FW delays as port of max VTOTAL calculated for
SubVP + DRR cases (since it is part of the microschedule).
- Also add margin for the max VTOTAL possible for SubVP + DRR cases.
- Due to rounding errors in FW (integer arithmetic), the microschedule
calculation can get pushed to the next frame (incorrectly) in cases
where we use the max VTOTAL possible to complete the MCLK switch.
- When the rounding error occurs, we are only off by 1-2 lines,
use 40us margin which is working consistently.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Data return times when using lowest memclk can be <= 60us, which can cause
underflow on high bandwidth displays with a workload.
[HOW?]
Enforce a minimum prefetch time during validation for low memclk modes.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC version 3.2.210 brings along the following:
- Investigate tool reported FCLK P-state deviations
- Fix null pointer issues found in emulation
- Add DSC delay factor workaround
- Round up DST_after_scaler to nearest int
- Use forced DSC bpp in DML
- Fix DCN32 DSC delay calculation
- Add a debug option HBR2CP2520 over TPS4
- Stop waiting for vblank during pipe programming
- Modify checks to enable TPS3 pattern when required
- Remove rate check from pixel rate divider update
- Check validation passed after applying pipe split changes
- Update DML formula
- Don't enable ODM + MPO
- Include virtual signal to set k1 and k2 values
- Reinit DPG when exiting dynamic ODM
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain 4K high refresh rate modes requiring DSC are exhibiting top
of screen underflow corruption. Increasing the DSC delay by a factor
of 6 percent stops the underflow for most use cases.
[How]
Multiply DSC delay requirement in DML by a factor.
Add debug option to make this DSC delay factor configurable.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How] There are cases when we may need to override the hardcoded
TPS4 test pattern. Added parameters and config option to be able to
allow this.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Leo Chen <sancchen@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The file dc.c has multiple comments that do not follow the kernel-doc or
are made in a distracting way. This commit alleviates part of this issue
by reorganizing some comments inside the dc file.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC version 3.2.209 brings along the following:
* Improve color manipulation
* Add corrections to DML and some flag configuration
* Updates for DCN32x
* Expand kernel-doc
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit adds extra documentation for elements related to FAMs.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Aurabindo Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We split out PSR config from "global" to "per-panel" config settings.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC stream can be seen as a representation of the DCN backend or the data
struct that represents the center of the display pipeline. The front end
(i.e., planes) is connected to the DC stream, and in its turn, streams
are connected to the DC link. Due to this dynamic, DC must handle the
following scenarios:
1. A stream is removed;
2. A new stream is created;
3. An unchanged stream had some updates on its planes.
These combinations require that the new stream data struct become
updated and has a valid global state. For handling multiple corner cases
associated with stream operations, this commit introduces a function
dedicated to manipulating stream changes and invokes the state
validation function after that.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Co-developed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The commit stream function does not include surfaces of unaffected
streams, which may lead to some blank screens during mode change in some
edge cases. This commit adds surfaces of unaffected streams followed by
kernel-doc for documenting some of the fields that participate in this
change.
v2: squash in kerneldoc warning fix (Alex)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Co-developed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC adds an instance of DML (which contains VBA) to each context, and
multiple threads might write back to the global VBA resulting in data
overwriting. To keep the consistency with other parts of the DC code,
this commit changes dc_commit_streams to copy the current DC state, and
as a result, it also changes the function signature to expect streams
instead of a context.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Co-developed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Change commit sequence will impact all ASICs. It is prudent to run this
update in small steps to keep issues under control and avoid any
potential regression. With this idea in mind, this commit is preparation
work for the complete transition to the new commit sequence. To maintain
this change manageable across multiple ASICs, this commit adds a new
function named dc_commit_streams which is a copy of the dc_commit_state
with some minor changes. Finally, inside the dc_commit_state, we check
if we are using DCN32x or above and enable the new sequence only for
those devices.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Co-developed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC version 3.2.207 brings along the following:
- PMFW z-state interface update
- Cursor update refactor
- Fixes to DSC validation, DCFCLK during Freesync, etc.
- Code cleanup
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Dpia hpd interrupt processing is disabled when entering S4/S0i3 and
would be reenabled after detection completes during resuming. Because,
keeping hpd interrupts enabled during detection leads to multiple
detections for the same hpd transition. There is a S4 case where dpia
hpd interrupt is missed when driver is in transitioning from hpd
interrupt processing disable to enable and the display does not light
up.
[How]
- Added dmub inbox command DMUB_CMD__DPIA_HPD_INT_ENABLE to explicitly
control dmub to issue dpia hpd interrupt or not. If dpia hpd interrupt
is disabled, dmub will keep the hpd pending and post it once driver
reenables dpia hpd interrupt or when querying with
DMUB_CMD__QUERY_HPD_STATE.
- Added dmub boot option dpia_hpd_int_enable_supported to notify dmub
about whether DMUB_CMD__DPIA_HPD_INT_ENABLE command would be used.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Mustapha Ghaddar <Mustapha.Ghaddar@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add a helper to map ODM/MPC/Multi-Plane resources from DC
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We split out ILR config from "global" to "per-panel" config settings.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- LTTPR mode can be be dynamically changed
- fixes divide by zero error
- features able to use same interface to update cursor info
- fixes for llvm compilation issues
- Fixes DIO FIFO underflow and other FIFO errors
- Partially valid EDIDs handled properly
- Phatom pipes are skipped when checking pending flip
- Fixed audio on audio on display after unplugging
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Several transitions were fixed that will allow Dynamic ODM and MPO
transitions to be supported on DCN32.
1) Due to resource limitations, in certain scenarios that require an MPO
plane to be split, the features cannot be combined with the current
policy. This is due to unsafe transitions being required (OPP instance
per MPCC being switched on active pipe is not supported by DCN), to
support the split plane with ODM active as it moves across the viewport.
Dynamic ODM will now be disabled when MPO is required.
2) When exiting MPO and re-entering ODM, DC assigns an inactive pipe for
the next ODM pipe, which under previous power gating policy would result
in programming a gated DSC HW block. New policy dynamically
gates/un-gates DSC blocks when Dynamic ODM is active to support
transitions on DCN32 only.
3) Entry and exit from 3 plane MPO and Dynamic ODM requires a minimal
transition so that all pipes which require their MPCC OPP instance to
be changed have a full frame to be disabled before reprogramming. To
solve this, the Dynamic ODM policy now utilizes minimal state
transitions when entering or exiting 3 plane scenarios.
4) Various fixes to DCN32 pipe merge/split algorithm to support Dynamic
ODM and MPO transitions.
In summary, this commit fixes various transitions to support ODM->MPO
and MPO->ODM.
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Update MALL SS NumWays calculation according
to programming guide.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Don't use MALL buffering of any kind when the
surface is TMZ
- Workaround for a HW bug
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
adding debug keys used for compliance test.
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Fix urgent latency override for DCN32/DCN321
- Correct hostvm flag in DCN31
- Added new Asic Id for DCN301
- Adjust to 2 phys in DCN301
- Update dummy P-state search to use DCN32 DML
- Increase dcn315 pstate change latency
- Disable OTG WA for the plane_state NULL case on DCN314
- Update dccg based on HW delta
- Correct num_dsc for DCN314
- Fix DP DSC compliance failure with DCN314
- Refactor edp power sequencer codes
- update gamut remap if plane has changed
- Skip audio setup when audio stream is enabled
- Display distortion after hotplug LG Ultrafine 5K tiled display
- Fix DP MST timeslot issue when fallback happened
- Uncomment SubVP pipe split assignment in driver
- Enable committing subvp config
- Do second pass through DML for DET calculation
- Don't allocate DET for phantom pipes
- Modify DML to adjust Vstartup Position
- Ignore k1/k2 values for virtual signal to avoid assert
- Fix failures of disabling primary planes
- Do not compare integers of different widths
- Fix empty slot problem of EDID management
- Revise Sink device string ID width in dmub psr
- Log vertical interrupt 1 for debug
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Port DCN30 420 logic to DCN32
- Remove some unused definitions from DCN32/321
- Remove dp dig pixle rate div policy from dcn314
- Fix dcn315 reading of memory channel count and width
- Fix SubVP and ODM relevant issues
- Fix pipe split, MPO and ODM relevant issues
- Support proper mst payload removal when link is not in mst mode in dc
- Assume an LTTPR is always present on fixed_vs links
- Rework recent update PHY state commit
- Add debug option and logs
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why and How]
- Add a debug option for allocating extra way for cursor
- Remove usage of cache_cursor_addr since it's not gaurenteed
to be populated
- Include cursor size in MALL calculation if it exceeds the
DCN cursor buffer size (and don't need extra way for cursor)
Reviewed-by: Aurabindo Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
*Fixed register definitions for DCN32/321
*Adding log for spread_spectrum_info
*Reverted DSC programming sequence change
*Correct I2C register offset
*Updated DCN30 header files, viewport position for phantom pipes
*Enable dlg and vba compilation for dcn314
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Regkey option for forcing num ways for subvp for debug purposes
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Leverage SW cursor fall back for SubVP when the cursor is too big. We
want to take advantage of being able to fallback to SW cursor when
possible because it's not worth it to disable MCLK switching because the
cursor is slightly too big.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aurabindo Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why && How]
We would like to have visual confirm color support for SubVP.
1. Set visual confirm color to red: SubVP is enable on this
display;
2. Set visual confirm color to green: SubVP is enable on
other display and DRR is on this display;
3. Set visual confirm color to blue: SubVP is enable on
other display and DRR is off on this display;
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Refactor edp dsc codes.
We split out edp dsc config from "global" to "per-panel" config settings.
Reviewed-by: Mike Hsieh <mike.hsieh@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to get the visual confirm color of the bottom-most pipe
for test automation.
[How]
Save the visual confirm color to plane_state before program to MPC;
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
enable_sw_cntl_psr flag is not needed.
For PSR1 and PSR2, we should be passing
dirty rectangle and cursor updates to FW
regardless of enable_sw_cntl_psr flag.
[How]
Remove enable_sw_cntl_psr flag from driver.
Send cursor info and dirty rectagle status to
dmub only in the case of dcn31 and above.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Useful for external teams debugging LTTPR issues
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
RV2 do not change pipe split policy in the
minimal pipe split transition state.
This will unblock mode support on some
parts that limit to DPM0 for power reason.
[How]
Do not change pipe split policy in the
minimal pipe split transition state to
allow 4k multi display configs to be
supported at DPM0.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This verion brings along following fixes:
-Add scaling factor for SubVP
-Modify stop_dbg_mode return value
-Add gfx_off members and document
-Add GFXOFF function for vangogh
-Add GFXOFF stats to debug
-Fix codestyle problems
-Fix overflow on MIN_I64
-Fix Unneeded semicolon
-Fix comment typo
-Remove useless condition in amdgpu_job_stop_all_jobs_on_sched()
-Add decoder_iv_ts helper for ih_v6
-Add chip version to DCN32
-Avoid doing vm_init multiple time
-Modify size calculation in MALL
-Fix DSC for phantom pipes
-Update clock table policy for DCN314
-Modify header inclusion pattern
-Fix plug/unplug external monitor will playback MPO video
-Add debug parameter to retain default clock table
-Increase tlb flush timeout for sriov
-Fix compare intergers of different widths
-Add reserved dc_log_type
-Fix pixel clock programming
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, we are using soc._clock_tmp[] to temporarily store and modify
data from soc.clock_limits[] before copying it back into
soc.clock_limits[] (because modifying data directly in
soc.clock_limits[] causes unintended behavior). However, this approach
has a number of downsides, such as:
1. struct _vcs_dpi_soc_bounding_box_st's creation/destruction
aren't well defined (which could mean more unintended
behavior).
2. Throwing "temp" varibles in structs everywhere doesn't make
for a particularly readable codebase.
For these reasons, we should get rid of soc._clock_tmp[] by defining a
struct scratch within struct dc that, contains within it all of the
temporary variables (including _clock_tmp[]) such that it is obvious how
they are intended to be used.
Co-authored-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add details about color correction capabilities and explain a bit about
differences between DC hw generations and also how they are mapped
between DRM and DC interface. Two schemas for DCN 2.0 and 3.0 (converted
to svg from the original png) is included to illustrate it. They were
obtained from a discussion[1] in the amd-gfx mailing list.
[1] https://lore.kernel.org/amd-gfx/20220422142811.dm6vtk6v64jcwydk@mail.igalia.com/
v1:
- remove redundant comments (Harry)
- fix typos (Harry)
v2:
- reword introduction of color section
- add co-dev tag for Harry - who provided most of the info
- fix typos (Tales)
- describe missing struct parameters (Tales and Siqueira)
Co-developed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Tales Aparecida <tales.aparecida@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In the DCN code, we can find some references to three different pipe
split policies but no clear description. This commit adds some
kernel-doc that explains more about these options and a little bit of
their impact.
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need a way to retain default clock table to aid
the investigation into why 8k@30 display not
lighting up on dcn314
[How]
Use flag to prevent execution of bw_params helper
function and function for updating bw_bounding_box
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Daniel Miess <Daniel.Miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
-Fix edp panel missing event
-Set ARGB16161616 pixel format to 26
-Fix dcn32 interger issue
-Clear optc underflow bit after ODM clock off
-Fix issue with stereo3D
-Fix DML2 lightup issue
-Correct DTBCLK for dcn314
-Revert for a regression
-Fix clocks and bugs in DML2
-Enable SubVP by defalut on DCN32 & DCN321
-Corret boundary condition for engin ID on DCN303
-Fix FRL encoder override registry key
-Fix VPG for dcn314 HPO
-Fix Linux compile-time warning
-Add new prefetch modes in DML for DCN32
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Move fpu file to dml folder
- Fix CAB allocation for multiple displays
- Add a variable to update FCLK
- Fix TMDS 4K@60Hz YCbCr420 corruption issue
- Fix MPC tree infinite loop in some case
- Fix HDMI VSIF V3 blank screen issue
- Add some documentation to the code
- Allow alternate prefetch modes in DML for DCN32
- Fix VPG instancing for dcn314 HPO
- Check correct bounds for stream encoder instances for DCN303
- Enable SubVP by default on DCN32 & DCN321
- Fix DTBCLK not correct for dcn314
- Fix Compile-time warning
- Fix the stereo mode hang issue
- Fix display light up issue
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
SUBVP_START_LINE must be aligned to 2 swaths, so add
16 lines of margin so the start line can be adjusted by
up to 16 lines for alignment purposes in FW.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver is restricting voltage levels if system cannot switch
in vblank.
[How]
Change allow_for_pstate_or_stutter_in_vblank_final from
dm_prefetch_support_uclk_fclk_and_stutter to
dm_prefetch_support_uclk_fclk_and_stutter_if_possible.
Add support for a new registry property,
DalDMLDisallowAlternatePrefetchModes, for easier debugging.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Add a variable to update FCLK latency
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Copy crc_skip_count when duplicating CRTC state
- Add debug option for idle optimizations on cursor updates
- Disable MPC split for DCN32/321
- Add missing ODM 2:1 policy logic
- Update DCN32 and DCN321 SR latencies
- Add reinstate dram in the FPO logic
- Add dc_ctx to link_enc_create() parameters
- Cache cursor when cursor exceeds 64x64
- Add support for manual DMUB FAMS trigger
- Fix dpstreamclk programming
- Add missing AUDIO_DTO_SEL reg field
- Add OTG/ODM functions
- Use correct clock source constructor for DCN314
- Use correct DTO_SRC_SEL for 128b/132b encoding
- Add pixel rate div calcs and programming
- Remove FPU flags from DCN30 Makefile
- Create patch bounding box function for isolate FPU
- Move mclk calculation function to DML
- Remove FPU operations from dcn201 resources
- Fallback to SW cursor if SubVP + cursor too big
- Drop unnecessary FPU flags on dcn302 files
- Reboot while unplug hdcp enabled dp from mst hub
- Reset pipe count when iterating for DET override
- Calculate MALL cache lines based on Mblks required
- Fix two MPO videos in single display ODM combine mode
- Guard against zero memory channels
- Updates SubVP + SubVP DRR cases updates
- Fix OPTC function pointers for DCN314
- Add enable/disable FIFO callbacks to stream setup
- Avoid MPC infinite loop
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
