new drivers:
- panthor: ARM Mali/Immortalis CSF-based GPU driver
core:
- add a CONFIG_DRM_WERROR option
- make more headers self-contained
- grab resv lock in pin/unpin
- fix vmap resv locking
- EDID/eDP panel matching
- Kconfig cleanups
- DT sound bindings
- Add SIZE_HINTS property for cursor planes
- Add struct drm_edid_product_id and helpers.
- Use drm device based logging in more drm functions.
- drop seq_file.h from a bunch of places
- use drm_edid driver conversions
dp:
- DP Tunnel documentation
- MST read sideband cap
- Adaptive sync SDP prep work
ttm:
- improve placement for TTM BOs in idle/busy handling
panic:
- Fixes for drm-panic, and option to test it.
- Add drm panic to simpledrm, mgag200, imx, ast
bridge:
- improve init ordering
- adv7511: allow GPIO pin sharing
- tc358775: add tc358675 support
panel:
- AUO B120XAN01.0
- Samsung s6e3fa7
- BOE NT116WHM-N44
- CMN N116BCA-EA1,
- CrystalClear CMT430B19N00
- Startek KD050HDFIA020-C020A
- powertip PH128800T006-ZHC01
- Innolux G121X1-L03
- LG sw43408
- Khadas TS050 V2
- EDO RM69380 OLED
- CSOT MNB601LS1-1
amdgpu:
- HDCP/ODM/RAS fixes
- Devcoredump improvements
- Expose VCN activity via sysfs
- SMY 13.0.x updates
- Enable fast updates on DCN 3.1.4
- Add dclk and vclk reporting on additional devices
- Add ACA RAS infrastructure
- Implement TLB flush fence
- EEPROM handling fixes
- SMUIO 14.0.2 support
- SMU 14.0.1 Updates
- SMU 14.0.2 support
- Sync page table freeing with TLB flushes
- DML2 refactor
- DC debug improvements
- DCN 3.5.x Updates
- GPU reset fixes
- HDP fix for second GFX pipe on GC 10.x
- Enable secondary GFX pipe on GC 10.3
- Refactor and clean up BACO/BOCO/BAMACO handling
- Remove invalid TTM resource start check
- UAF fix in VA IOCTL
- GPUVM page fault redirection to secondary IH rings for IH 6.x
- Initial support for mapping kernel queues via MES
- Fix VRAM memory accounting
amdkfd:
- MQD handling cleanup
- Preemption handling fixes for XCDs
- TLB flush fix for GC 9.4.2
- Properly clean up workqueue during module unload
- Fix memory leak process create failure
- Range check CP bad op exception targets to avoid reporting invalid exceptions to userspace
- Fix eviction fence handling
- Fix leak in GPU memory allocation failure case
- DMABuf import handling fix
- Enable SQ watchpoint for gfx10
i915:
- Adding new DG2 PCI ID
- add context hints for GT frequency
- enable only one CCS for compute workloads
- new workarounds
- Fix UAF on destroy against retire race and remove two earlier partial fixes
- Limit the reserved VM space to only the platforms that need it
- Fix gt reset with GuC submission is disable
- Add and use gt_to_guc() wrapper
i915/xe display:
- Lunar Lake display enabling, including cdclk and other refactors
- BIOS/VBT/opregion related refactor
- Digital port related refactor/clean-up
- Fix 2s boot time regression on DP panel replay init
- Remove duplication on audio enable/disable on SDVO and g4x+ DP
- Disable AuxCCS framebuffers if built for Xe
- Make crtc disable more atomic
- Increase DP idle pattern wait timeout to 2ms
- Start using container_of_const() for some extra const safety
- Fix Jasper Lake boot freeze
- Enable MST mode for 128b/132b single-stream sideband
- Enable Adaptive Sync SDP Support for DP
- Fix MTL supported DP rates - removal of UHBR13.5
- PLL refactoring
- Limit eDP MSO pipe only for display version 20
- More display refactor towards independence from i915 dev_priv
- Convert i915/xe fbdev to DRM client
- More initial work to make display code more independent from i915
xe:
- improved error capture
- clean up some uAPI leftovers
- devcoredump update
- Add BMG mocs table
- Handle GSCCS ER interrupt
- Implement xe2- and GuC workarounds
- struct xe_device cleanup
- Hwmon updates
- Add LRC parsing for more GPU instruction
- Increase VM_BIND number of per-ioctl Ops
- drm/xe: Add XE_BO_GGTT_INVALIDATE flag
- Initial development for SR-IOV support
- Add new PCI IDs to DG2 platform
- Move userptr over to start using hmm_range_fault
msm:
- Switched to generating register header files during build process
instead of shipping pre-generated headers
- Merged DPU and MDP4 format databases.
- DP:
- Stop using compat string to distinguish DP and eDP cases
- Added support for X Elite platform (X1E80100)
- Reworked DP aux/audio support
- Added SM6350 DP to the bindings
- GPU:
- a7xx perfcntr reg fixes
- MAINTAINERS updates
- a750 devcoredump support
radeon:
- Silence UBSAN warnings related to flexible arrays
nouveau:
- move some uAPI objects to uapi headers
omapdrm:
- console fix
ast:
- add i2c polling
qaic:
- add debugfs entries
exynos:
- fix platform_driver .owner
- drop cleanup code
mediatek:
- Use devm_platform_get_and_ioremap_resource() in mtk_hdmi_ddc_probe()
- Add GAMMA 12-bit LUT support for MT8188
- Rename mtk_drm_* to mtk_*
- Drop driver owner initialization
- Correct calculation formula of PHY Timing
-----BEGIN PGP SIGNATURE-----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=ocVM
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2024-05-15' of https://gitlab.freedesktop.org/drm/kernel
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm subsystems for 6.10.
In drivers the main thing is a new driver for ARM Mali firmware based
GPUs, otherwise there are a lot of changes to amdgpu/xe/i915/msm and
scattered changes to everything else.
In the core a bunch of headers and Kconfig was refactored, along with
the addition of a new panic handler which is meant to provide a user
friendly message when a panic happens and graphical display is
enabled.
New drivers:
- panthor: ARM Mali/Immortalis CSF-based GPU driver
Core:
- add a CONFIG_DRM_WERROR option
- make more headers self-contained
- grab resv lock in pin/unpin
- fix vmap resv locking
- EDID/eDP panel matching
- Kconfig cleanups
- DT sound bindings
- Add SIZE_HINTS property for cursor planes
- Add struct drm_edid_product_id and helpers.
- Use drm device based logging in more drm functions.
- drop seq_file.h from a bunch of places
- use drm_edid driver conversions
dp:
- DP Tunnel documentation
- MST read sideband cap
- Adaptive sync SDP prep work
ttm:
- improve placement for TTM BOs in idle/busy handling
panic:
- Fixes for drm-panic, and option to test it.
- Add drm panic to simpledrm, mgag200, imx, ast
bridge:
- improve init ordering
- adv7511: allow GPIO pin sharing
- tc358775: add tc358675 support
panel:
- AUO B120XAN01.0
- Samsung s6e3fa7
- BOE NT116WHM-N44
- CMN N116BCA-EA1,
- CrystalClear CMT430B19N00
- Startek KD050HDFIA020-C020A
- powertip PH128800T006-ZHC01
- Innolux G121X1-L03
- LG sw43408
- Khadas TS050 V2
- EDO RM69380 OLED
- CSOT MNB601LS1-1
amdgpu:
- HDCP/ODM/RAS fixes
- Devcoredump improvements
- Expose VCN activity via sysfs
- SMY 13.0.x updates
- Enable fast updates on DCN 3.1.4
- Add dclk and vclk reporting on additional devices
- Add ACA RAS infrastructure
- Implement TLB flush fence
- EEPROM handling fixes
- SMUIO 14.0.2 support
- SMU 14.0.1 Updates
- SMU 14.0.2 support
- Sync page table freeing with TLB flushes
- DML2 refactor
- DC debug improvements
- DCN 3.5.x Updates
- GPU reset fixes
- HDP fix for second GFX pipe on GC 10.x
- Enable secondary GFX pipe on GC 10.3
- Refactor and clean up BACO/BOCO/BAMACO handling
- Remove invalid TTM resource start check
- UAF fix in VA IOCTL
- GPUVM page fault redirection to secondary IH rings for IH 6.x
- Initial support for mapping kernel queues via MES
- Fix VRAM memory accounting
amdkfd:
- MQD handling cleanup
- Preemption handling fixes for XCDs
- TLB flush fix for GC 9.4.2
- Properly clean up workqueue during module unload
- Fix memory leak process create failure
- Range check CP bad op exception targets to avoid reporting invalid exceptions to userspace
- Fix eviction fence handling
- Fix leak in GPU memory allocation failure case
- DMABuf import handling fix
- Enable SQ watchpoint for gfx10
i915:
- Adding new DG2 PCI ID
- add context hints for GT frequency
- enable only one CCS for compute workloads
- new workarounds
- Fix UAF on destroy against retire race and remove two earlier partial fixes
- Limit the reserved VM space to only the platforms that need it
- Fix gt reset with GuC submission is disable
- Add and use gt_to_guc() wrapper
i915/xe display:
- Lunar Lake display enabling, including cdclk and other refactors
- BIOS/VBT/opregion related refactor
- Digital port related refactor/clean-up
- Fix 2s boot time regression on DP panel replay init
- Remove duplication on audio enable/disable on SDVO and g4x+ DP
- Disable AuxCCS framebuffers if built for Xe
- Make crtc disable more atomic
- Increase DP idle pattern wait timeout to 2ms
- Start using container_of_const() for some extra const safety
- Fix Jasper Lake boot freeze
- Enable MST mode for 128b/132b single-stream sideband
- Enable Adaptive Sync SDP Support for DP
- Fix MTL supported DP rates - removal of UHBR13.5
- PLL refactoring
- Limit eDP MSO pipe only for display version 20
- More display refactor towards independence from i915 dev_priv
- Convert i915/xe fbdev to DRM client
- More initial work to make display code more independent from i915
xe:
- improved error capture
- clean up some uAPI leftovers
- devcoredump update
- Add BMG mocs table
- Handle GSCCS ER interrupt
- Implement xe2- and GuC workarounds
- struct xe_device cleanup
- Hwmon updates
- Add LRC parsing for more GPU instruction
- Increase VM_BIND number of per-ioctl Ops
- drm/xe: Add XE_BO_GGTT_INVALIDATE flag
- Initial development for SR-IOV support
- Add new PCI IDs to DG2 platform
- Move userptr over to start using hmm_range_fault
msm:
- Switched to generating register header files during build process
instead of shipping pre-generated headers
- Merged DPU and MDP4 format databases.
- DP:
- Stop using compat string to distinguish DP and eDP cases
- Added support for X Elite platform (X1E80100)
- Reworked DP aux/audio support
- Added SM6350 DP to the bindings
- GPU:
- a7xx perfcntr reg fixes
- MAINTAINERS updates
- a750 devcoredump support
radeon:
- Silence UBSAN warnings related to flexible arrays
nouveau:
- move some uAPI objects to uapi headers
omapdrm:
- console fix
ast:
- add i2c polling
qaic:
- add debugfs entries
exynos:
- fix platform_driver .owner
- drop cleanup code
mediatek:
- Use devm_platform_get_and_ioremap_resource() in mtk_hdmi_ddc_probe()
- Add GAMMA 12-bit LUT support for MT8188
- Rename mtk_drm_* to mtk_*
- Drop driver owner initialization
- Correct calculation formula of PHY Timing"
* tag 'drm-next-2024-05-15' of https://gitlab.freedesktop.org/drm/kernel: (1477 commits)
drm/xe/ads: Use flexible-array
drm/xe: Use ordered WQ for G2H handler
drm/msm/gen_header: allow skipping the validation
drm/msm/a6xx: Cleanup indexed regs const'ness
drm/msm: Add devcoredump support for a750
drm/msm: Adjust a7xx GBIF debugbus dumping
drm/msm: Update a6xx registers XML
drm/msm: Fix imported a750 snapshot header for upstream
drm/msm: Import a750 snapshot registers from kgsl
MAINTAINERS: Add Konrad Dybcio as a reviewer for the Adreno driver
MAINTAINERS: Add a separate entry for Qualcomm Adreno GPU drivers
drm/msm/a6xx: Avoid a nullptr dereference when speedbin setting fails
drm/msm/adreno: fix CP cycles stat retrieval on a7xx
drm/msm/a7xx: allow writing to CP_BV counter selection registers
drm: zynqmp_dpsub: Always register bridge
Revert "drm/bridge: ti-sn65dsi83: Fix enable error path"
drm/fb_dma: Add checks in drm_fb_dma_get_scanout_buffer()
drm/fbdev-generic: Do not set physical framebuffer address
drm/panthor: Fix the FW reset logic
drm/panthor: Make sure we handle 'unknown group state' case properly
...
[Why]
During DP tunnel creation, CM preallocates BW and reduces
estimated BW of other DPIA. CM release preallocation only
when allocation is complete. Display mode validation logic
validates timings based on bw available per host router.
In multi display setup, this causes bw allocation failure
when allocation greater than estimated bw.
[How]
Do zero alloc to make the CM to release preallocation and
update estimated BW correctly for all DPIAs per host router.
Reviewed-by: PeiChen Huang <peichen.huang@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes 29 UNINIT issues reported by Coverity.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes 49 UNINIT issues reported by Coverity.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some of the includes used in the DC can be removed and others need to be
update. This commit adjusts some of those headers in the display code.
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why and how:
as part of cleanup, need to refactor vpg. It was improperly referenced
as a dcn specfic part of link. the dcn agnostic code needed was ripped out
and put into vpg.h, now in dc/inc/hw.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Parandhaman K <parandhaman.k@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Enabling higher compiler warning levels results in many issues that can
be trivially resolved as well as some potentially critical issues.
[how]
Fix all compiler warnings found with various compilers and higher
warning levels. Primarily, potentially uninitialized variables and
unreachable code.
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The function to count the number of valid connectors does not
guarantee that the first n indices are valid, only that there
exist n valid indices. When invalid indices are present, this
results in later valid connectors being missed, as processing
would end after checking n indices.
[How]
- count valid indices separately from total indices examined
- add explicit definition of MAX_LINKS
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Dmub provides several Replay residency calculation methods,
but current interface only supports either ALPM or PHY mode
[How]
Modify the interface for supporting different types
of Replay residency calculation.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Leon Huang <leon.huang1@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
To enable a new interface so alternate scrambling can be done via
security module.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Sung Joon Kim <sungjoon.kim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The original coasting vtotal is 2 bytes, and it need to
be amended to 4 bytes because low hz case.
[HOW]
Amend coasting vtotal from 2 bytes to 4 bytes.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: ChunTao Tso <chuntao.tso@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are trying to get rid of all multiplications from allocation
functions to prevent integer overflows. Here the multiplication is
obviously safe, but using kcalloc() is more appropriate and improves
readability. This patch has no effect on runtime behavior.
Link: https://www.kernel.org/doc/html/next/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Link: https://github.com/KSPP/linux/issues/162
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Lenko Donchev <lenko.donchev@gmail.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The old asic only have 1 pwrseq hw.
We don't need to map the diginst to pwrseq inst in old asic.
[How]
1. Only mapping dig to pwrseq for new asic.
2. Move mapping function into dcn specific panel control component
Cc: Stable <stable@vger.kernel.org> # v6.6+
Cc: Mario Limonciello <mario.limonciello@amd.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/3122
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Lewis Huang <lewis.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In the first if statement, we're checking if 'replay' is NULL. But in
the second if statement, we're not checking if 'replay' is NULL again
before calling replay->funcs->replay_set_power_opt().
if (replay == NULL && force_static)
return false;
...
if (link->replay_settings.replay_feature_enabled &&
replay->funcs->replay_set_power_opt) {
replay->funcs->replay_set_power_opt(replay, *power_opts, panel_inst);
link->replay_settings.replay_power_opt_active = *power_opts;
}
If 'replay' is NULL, this will cause a null pointer dereference.
Fixes the below found by smatch:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_edp_panel_control.c:895 edp_set_replay_allow_active() error: we previously assumed 'replay' could be null (see line 887)
Fixes: c7ddc0a800 ("drm/amd/display: Add Functions to enable Freesync Panel Replay")
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Suggested-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]:
issues fixed:
- comparison with wider integer type in loop condition which can cause
infinite loops
- pointer dereference before null check
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Sohaib Nadeem <sohaib.nadeem@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Need to fix some broken logic and sequencing in initial commit
[HOW]
Fix logic handling override deprogramming when exiting SQ128.
Don't exit early from dp_set_hw_lane_settings for DP2/FIXED_VS case.
Move LTTPR 128b/132b check out of requires_hwss and check during
runtime, as LTTPR caps are not populated on initial call.
Add pending_test_pattern to link state to allow HWSS to set FFE overrides
on retimer TX and/or skip setting APU TX FFE depending on requested pattern.
Use updated clock source for SQ128 override sequence.
Skip HW FFE preset programming when performing test pattern overrides.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We Double-check link status if training successful,
but miss the lane align status.
[HOW]
Add the lane align status check
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Zhikai Zhai <zhikai.zhai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
wait_time_microsec = max(wait_time_microsec, (uint32_t)
DPIA_CLK_SYNC_DELAY);
Above line is trying to assign the maximum value between
'wait_time_microsec' and 'DPIA_CLK_SYNC_DELAY' to wait_time_microsec.
However, 'wait_time_microsec' has not been assigned a value before this
line, initialize 'wait_time_microsec' at the point of declaration.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_dpia.c:697 dpia_training_eq_non_transparent() error: uninitialized symbol 'wait_time_microsec'.
Fixes: 630168a973 ("drm/amd/display: move dp link training logic to link_dp_training")
Cc: Wenjing Liu <wenjing.liu@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some of the CONFIG_DRM_AMD_DC_FP was added in some non-related FPU code,
which may cause confusion. This commit dropped some of the unnecessary
guards.
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
0 nits is a valid default value for OLED panels. So, update the relevant
comment to account for that fact.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Signed-off-by: Camille Cho <camille.cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Only required if FIXED_VS retimer does not support DP2-capable.
[HOW]
Gate link rate toggle with DP 128b/132b LTTPR channel coding cap check.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The New sequence has been in use in DCN314 with no regressions
introduced. Therefore, it is safe to enable this sequence for all
devices using FIXED_VS retimers. So, remove the legacy codepath and its
associated config flag.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The error message buffer overflow 'dc->links' 12 <= 12 suggests that the
code is trying to access an element of the dc->links array that is
beyond its bounds. In C, arrays are zero-indexed, so an array with 12
elements has valid indices from 0 to 11. Trying to access dc->links[12]
would be an attempt to access the 13th element of a 12-element array,
which is a buffer overflow.
To fix this, ensure that the loop does not go beyond the last valid
index when accessing dc->links[i + 1] by subtracting 1 from the loop
condition.
This would ensure that i + 1 is always a valid index in the array.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_dpia_bw.c:208 get_host_router_total_dp_tunnel_bw() error: buffer overflow 'dc->links' 12 <= 12
Fixes: 59f1622a5f ("drm/amd/display: Add dpia display mode validation logic")
Cc: PeiChen Huang <peichen.huang@amd.com>
Cc: Aric Cyr <aric.cyr@amd.com>
Cc: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dc should have a flag for DM to enable usb4_bw_alloc in dptx
[How]
- Add usb4_bw_alloc_support flag in dc_config
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Peichen Huang <peichen.huang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The 'status' variable in 'core_link_read_dpcd()' &
'core_link_write_dpcd()' was uninitialized.
Thus, initializing 'status' variable to 'DC_ERROR_UNEXPECTED' by default.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dpcd.c:226 core_link_read_dpcd() error: uninitialized symbol 'status'.
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dpcd.c:248 core_link_write_dpcd() error: uninitialized symbol 'status'.
Cc: stable@vger.kernel.org
Cc: Jerry Zuo <jerry.zuo@amd.com>
Cc: Jun Lei <Jun.Lei@amd.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In link_set_dsc_pps_packet(), 'struct display_stream_compressor *dsc'
was dereferenced in a DC_LOGGER_INIT(dsc->ctx->logger); before the 'dsc'
NULL pointer check.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/link_dpms.c:905 link_set_dsc_pps_packet() warn: variable dereferenced before check 'dsc' (see line 903)
Cc: stable@vger.kernel.org
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Wenjing Liu <wenjing.liu@amd.com>
Cc: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns (or errors with CONFIG_WERROR=y) when performing arithmetic
with different enumerated types, which is usually a bug:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_dpia_bw.c:548:24: error: arithmetic between different enumeration types ('const enum dc_link_rate' and 'const enum dc_lane_count') [-Werror,-Wenum-enum-conversion]
548 | link_cap->link_rate * link_cap->lane_count * LINK_RATE_REF_FREQ_IN_KHZ * 8;
| ~~~~~~~~~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~
1 error generated.
In this case, there is not a problem because the enumerated types are
basically treated as '#define' values. Add an explicit cast to an
integral type to silence the warning.
Closes: https://github.com/ClangBuiltLinux/linux/issues/1976
Fixes: 5f3bce1326 ("drm/amd/display: Request usb4 bw for mst streams")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Dpia hpd status not in sync causing driver not enabling BW Alloc after
S4.
[How]
Update hpd_status of the link when querying hpd state from dmub in
dpia_query_hpd_status().
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When usb4 bandwidth allocation mode is enabled, driver need to request
bandwidth from connection manager. For mst link, the requested
bandwidth should be big enough for all remote streams.
[HOW]
- If mst link, the requested bandwidth should be the sum of all mst
streams bandwidth added with dp MTPH overhead.
- Allocate/deallcate usb4 bandwidth when setting dpms on/off.
- When doing display mode validation, driver also need to consider total
bandwidth of all mst streams for mst link.
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Peichen Huang <peichen.huang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
gcc prints a warning about a possible array overflow for a couple of
callers of dp_decide_lane_settings() after commit 1b56c90018f0 ("Makefile:
Enable -Wstringop-overflow globally"):
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_fixed_vs_pe_retimer.c: In function 'dp_perform_fixed_vs_pe_training_sequence_legacy':
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_fixed_vs_pe_retimer.c:426:25: error: 'dp_decide_lane_settings' accessing 4 bytes in a region of size 1 [-Werror=stringop-overflow=]
426 | dp_decide_lane_settings(lt_settings, dpcd_lane_adjust,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
427 | lt_settings->hw_lane_settings, lt_settings->dpcd_lane_settings);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_fixed_vs_pe_retimer.c:426:25: note: referencing argument 4 of type 'union dpcd_training_lane[4]'
I'm not entirely sure what caused this, but changing the prototype to expect
a pointer instead of an array avoids the warnings.
Fixes: 7727e7b60f ("drm/amd/display: Improve robustness of FIXED_VS link training at DP1 rates")
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Prepare for enabling the Panel Replay feature
[HOW]
- Add some Panel Replay setting functions in DC
- Add the Panel Replay resource in dcn35_resource.c
- Add debug masks for Panel Replay
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If bandwidth allocation feature is enabled, connection manager wont
limit the dp tunnel bandwidth. So, need to do display mode validation
for streams on dpia links to avoid oversubscription of dp tunnel
bandwidth.
[How]
- To read non reduced link rate and lane count and update
reported link capability.
- To calculate the bandwidth required for streams of dpia links
per host router and validate against the allocated bandwidth for
the host router.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: PeiChen Huang <peichen.huang@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
BL1_PWM_USER_LEVEL is meant for the user brightness level setting from
OS. However, we update it along with other ABM levels to the real PWM
value which could be ABMed.
[How]
Driver to cache and restore the user brightness level setting so that
DMUB can retrieve the last user setting in ABM config initialization.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Camille Cho <camille.cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Fix minor issues in BW Allocation Phase2.
[How]
- In set_usb4_req_bw_req(), link->dpia_bw_alloc_config.response_ready
flag should be reset before writing DPCD REQUEST_BW.
- Fix the granularity for value of 2 in get_bw_granularity().
- Removed bandwidth allocation support display fw boot option as
the fw would read feature enable status from bios.
- Clean up DPIA_EST_BW_CHANGED and DPIA_BW_REQ_SUCCESS cases in
dpia_handle_bw_alloc_response().
- Removed allocate_usb4_bw and deallocate_usb4_bw.
- Optimized loop in get_lowest_dpia_index().
- Updated link_dp_dpia_allocate_usb4_bandwidth_for_stream() and
set_usb4_req_bw_req() to always issue request bw.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: PeiChen Huang <peichen.huang@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain HDMI modes failed at dml cap check for uncompressed video but
they can still be supported for compressed video.
[How]
Add HDMI capacity computations using fixed31_32 in dc side.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Chris Park <chris.park@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can hang in place trying to send commands when the DMCUB isn't
powered on.
[How]
For functions that execute within a DC context or DC lock we can
wrap the direct calls to dm_execute_dmub_cmd/list with code that
exits idle power optimizations and reallows once we're done with
the command submission on success.
For DM direct submissions the DM will need to manage the enter/exit
sequencing manually.
We cannot invoke a DMCUB command directly within the DM execution
helper or we can deadlock.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
With DP2.1a expansion we are allowing DP40 cables to do UHBR13.5
how:
Assume UHBR10 means UHBR13.5 also for unknown cable type and
passive cable type.
Reviewed-by: George Shen <george.shen@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Ran Shi <ran.shi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark reports that brightness is not restored after Xorg dpms screen blank.
This behavior was introduced by commit d9e865826c ("drm/amd/display:
Simplify brightness initialization") which dropped the cached backlight
value in display code, but also removed code for when the default value
read back was less than 1 nit.
Restore this code so that the backlight brightness is restored to the
correct default value in this circumstance.
Reported-by: Mark Herbert <mark.herbert42@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3031
Cc: stable@vger.kernel.org
Cc: Camille Cho <camille.cho@amd.com>
Cc: Krunoslav Kovac <krunoslav.kovac@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Fixes: d9e865826c ("drm/amd/display: Simplify brightness initialization")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current implementation will choose to use refclk as dscclk. This is not
recommended by hardware team as refclk is a fixed value which could
cause unnecessary power consumption or it could be not enough for large
DSC timings. So we are adding new interfaces so we could switch to use
dynamically generated DSCCLK by DTO. So DSCCLK is programmable based on
current pixel clock and dispclk.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In previous case, Replay didn't identify the IRQ type, This commit fixes
the issues for the interrupt.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Dennis Chan <dennis.chan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The is_automated flag logic only applies to USB4 DPIA links during DP LL
compliance test automation. The flag should not be set for non-DPIA
cases.
[How]
Add check for DPIA link endpoint type before setting the flag. Also,
rename is_automated to skip_fallback_on_link_loss for clarity.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changing PBN calculation to be more in line with spec. We don't need to
inflate PBN_NATIVE value by the 1.006 margin, since that is already
taken care of in the get_pbn_per_slot function.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
OTG inst and pwrseq inst mapping is not align therefore we cannot use
otg_inst as pwrseq inst to get DCIO register.
[How]
1. Pass the correct pwrseq instance to dmub when set abm pipe.
2. LVTMA control index change from panel_inst to pwrseq_inst.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Phil Hsieh <phil.hsieh@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Lewis Huang <lewis.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY/HOW]
Add a new AUX sequence provided by vendor to improve
interop with specific display configurations.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Handover from DMUB to driver does not perform link rate toggle.
It might cause link training failure for boot up.
[HOW]
Force toggle rate wa for first link train.
link->vendor_specific_lttpr_link_rate_wa should be zero then.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Zhongwei <zhongwei.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MST relevant variables are maintained at drm side. As the result, we
still have to call drm_dp_remove_payload_part2() to update the relevant
values regardless the link is under mst mode or not. We used to have a
workaround patch to tackle this: commit 3d8fcc6740 ("drm/amd/display:
Extract temp drm mst deallocation wa into its own function")
Now it's time to remove the workaround and adjust the flow.
[How]
During deallocate_mst_payload(), source actually doesn't send out
ALLOCATE_PAYLOAD at the end as like the flow in allocate_mst_payload().
Call function dm_helpers_dp_mst_send_payload_allocation() at the end of
deallocate_mst_payload() is a bit confusing.
Separate dm_helpers_dp_mst_send_payload_allocation() into 2 functions.
Have a new function dm_helpers_dp_mst_update_mst_mgr_for_deallocation()
to replace dm_helpers_dp_mst_send_payload_allocation() for payload
deallocation.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Remove the brightness cache in DC. It uses a single value to represent
the brightness for both SDR and HDR mode. This leads to flash in HDR
on/off. It also unconditionally programs brightness as in HDR mode. This
may introduce garbage on SDR mode in miniLED panel.
[How]
Simplify the initialization flow by removing the DC cache and taking
what panel has as default. Expand the mechanism for PWM to DPCD Aux to
restore cached brightness value generally.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Camille Cho <camille.cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
