Reinstate commit 88b065943c ("drm/i915/dsi: Do display on
sequence later on icl+"), for the most part. Turns out some
machines (eg. Chuwi Minibook X) really do need that updated order.
It is also the order the Windows driver uses.
However we can't just undo the revert since that would again
break Lenovo 82TQ. After staring at the VBT sequences for both
machines I've concluded that the Lenovo 82TQ sequences look
somewhat broken:
- INIT_OTP is not present at all
- what should be in INIT_OTP is found in DISPLAY_ON
- what should be in DISPLAY_ON is found in BACKLIGHT_ON
(along with the actual backlight stuff)
The Chuwi Minibook X on the other hand has a full complement
of sequences in its VBT.
So let's try to deal with the broken sequences in the
Lenovo 82TQ VBT by simply swapping the (non-existent)
INIT_OTP sequence with the DISPLAY_ON sequence. Thus we
execute DISPLAY_ON when intending to execute INIT_OTP,
and execute nothing at all when intending to execute
DISPLAY_ON. That should be 100% equivalent to the
revert, for such broken VBTs.
Cc: stable@vger.kernel.org
Fixes: dc524d0597 ("Revert "drm/i915/dsi: Do display on sequence later on icl+"")
References: https://gitlab.freedesktop.org/drm/intel/-/issues/10071
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10334
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240305083659.8396-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
This reverts commit 88b065943c.
Lenovo 82TQ is unhappy if we do the display on sequence this
late. The display output shows severe corruption.
It's unclear if this is a failure on our part (perhaps
something to do with sending commands in LP mode after HS
/video mode transmission has been started? Though the backlight
on command at least seems to work) or simply that there are
some commands in the sequence that are needed to be done
earlier (eg. could be some DSC init stuff?). If the latter
then I don't think the current Windows code would work
either, but maybe this was originally tested with an older
driver, who knows.
Root causing this fully would likely require a lot of
experimentation which isn't really feasible without direct
access to the machine, so let's just accept failure and
go back to the original sequence.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10071
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240116210821.30194-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Apparently some BXT/GLK systems have DSI panels whose timings
don't agree with the normal cpu transcoder hblank>=32 limitation.
This is perhaps fine as there are no specific hblank/etc. limits
listed for the BXT/GLK DSI transcoders.
Move those checks out from the global intel_mode_valid() into
into connector specific .mode_valid() hooks, skipping BXT/GLK
DSI connectors. We'll leave the basic [hv]display/[hv]total
checks in intel_mode_valid() as those seem like sensible upper
limits regardless of the transcoder used.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9720
Fixes: 8f4b1068e7 ("drm/i915: Check some transcoder timing minimum limits")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127145028.4899-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
DSC parameter bits_per_pixel is stored in U6.4 format.
The 4 bits represent the fractional part of the bpp.
Currently we use compressed_bpp member of dsc structure to store
only the integral part of the bits_per_pixel.
To store the full bits_per_pixel along with the fractional part,
compressed_bpp is changed to store bpp in U6.4 formats. Intergral
part is retrieved by simply right shifting the member compressed_bpp by 4.
v2:
-Use to_bpp_int, to_bpp_frac_dec, to_bpp_x16 helpers while dealing
with compressed bpp. (Suraj)
-Fix comment styling. (Suraj)
v3:
-Add separate file for 6.4 fixed point helper(Jani, Nikula)
-Add comment for magic values(Suraj)
v4:
-Fix checkpatch warnings caused by renaming(Suraj)
v5:
-Rebase.
-Use existing helpers for conversion of bpp_int to bpp_x16
and vice versa.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20231110101020.4067342-3-ankit.k.nautiyal@intel.com
This change is to adjust TCLK-POST timing so DSI signaling can
meet CTS specification.
For clock lane, the TCLK-POST timing may be changed from
133.44 ns to 178.72 ns, which is greater than (60 ns+52*UI)
and is conformed to the CTS standard.
The computed UI is around 1.47 ns.
v2: remove the change of HS-TRAIL.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Signed-off-by: William Tseng <william.tseng@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230914095137.4132029-1-william.tseng@intel.com
Try to deal with duplicate child devices for the same DDI port
by attempting to initialize them in VBT defined order The first
on to succeed for a specific DDI port will be the one we use.
We'll also get rid of i915->display.vbt.ports[] here as any conflicts
will now be handled at encoder registration time rather than during
VBT parsing. Note that intel_bios_encoder_data_lookup() still remaims
for pre-DDI DP/HDMI ports as those don't (at least yet) use VBT
driven initialization.
TODO: DSI dual link handling is sketchy at best
v2: Leave intel_bios_encoder_port() to the encoder callback (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230630155846.29931-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The encoder hooks already get passed the crtc state so just
grab the crtc from there instead of from the connector state.
This is generally what everyone else does, so no reason for
icl_dsi.c to be different.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230608203057.23759-13-ville.syrjala@linux.intel.com
encoder->disable() is supposed to happen before the pipe/transcoder
gets disabled. The icl+ DSI code screwed that up and put most things
(including the transcoder disable itself) into encoder->disable().
Follow the common rules and hoist most things into the
encoder->post_disable() hook.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230608203057.23759-9-ville.syrjala@linux.intel.com
The programming of the DPHY vs. DSI _TIMING registers are
two separate steps in the TGL+ bspec sequence, with some
other stuff in between. Implement the same split.
Windows also seems follow the bspec TGL+ sequence, even
on ICL/JSL.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230608203057.23759-5-ville.syrjala@linux.intel.com
Doing the init OTP and display on DSI sequences back to back
doesn't really make any sense (a single sequence would suffice
then). Move the display on sequence to be done just before
backlight on, which is also what Windows does.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230608203057.23759-3-ville.syrjala@linux.intel.com
Looks like we're trying to talk to the DSI panel even before turning
it on, on icl+. Bspec doesn't actually specify when these should be
done, but certainly we need to turn the panel on at least before
talking to it. So let's move the power on + reset deassert steps to
be the first thing we do. This is also what Windows does.
v2: s/intel_dsi_msleep/msleep/
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230608203057.23759-2-ville.syrjala@linux.intel.com
The decision to use DFP output format conversion capabilities should be
during compute_config phase.
This patch adds new member to crtc_state to represent the final
output_format to the sink. In case of a DFP this can be different than
the output_format, as per the format conversion done via the PCON.
This will help to store only the format conversion capabilities of the
DP device in intel_dp->dfp, and use crtc_state to compute and store the
configuration for color/format conversion for a given mode.
v2: modified the new member to crtc_state to represent the final
output_format that eaches the sink, after possible conversion by
PCON kind of devices. (Ville)
v3: Addressed comments from Ville:
-Added comments to clarify difference between sink_format and
output_format.
-Corrected the order of setting sink_format and output_format.
-Added readout for sink_format in get_pipe_config hooks.
v4: Set sink_format for intel_sdvo too. (Ville)
v5: Rebased.
v6: Fixed condition to go for YCbCr420 format for dp and hdmi. (Ville)
v7: Fix the condition to set sink_format for HDMI.
Set hdmi output_format simply as sink_format. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v3)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427125605.487769-2-ankit.k.nautiyal@intel.com
The intel_dsi_msleep() helper skips sleeping if the MIPI-sequences have
a version of 3 or newer and the panel is in vid-mode.
This is based on the big comment around line 730 which starts with
"Panel enable/disable sequences from the VBT spec.", where
the "v3 video mode seq" column does not have any wait t# entries.
Checking the Windows driver shows that it does always honor
the VBT delays independent of the version of the VBT sequences.
Commit 6fdb335f1c ("drm/i915/dsi: Use unconditional msleep for
the panel_on_delay when there is no reset-deassert MIPI-sequence")
switched to a direct msleep() instead of intel_dsi_msleep()
when there is no MIPI_SEQ_DEASSERT_RESET sequence, to fix
the panel on an Acer Aspire Switch 10 E SW3-016 not turning on.
And now testing on a Nextbook Ares 8A shows that panel_on_delay
must always be honored otherwise the panel will not turn on.
Instead of only always using regular msleep() for panel_on_delay
do as Windows does and always use regular msleep() everywhere
were intel_dsi_msleep() is used and drop the intel_dsi_msleep()
helper.
Changes in v2:
- Replace all intel_dsi_msleep() calls instead of just
the intel_dsi_msleep(panel_on_delay) call
Cc: stable@vger.kernel.org
Fixes: 6fdb335f1c ("drm/i915/dsi: Use unconditional msleep for the panel_on_delay when there is no reset-deassert MIPI-sequence")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230425194441.68086-1-hdegoede@redhat.com
Now that we have laid the groundwork for YUV420 Enablement
we fill up native_420 field in vdsc_cfg and add appropriate
checks wherever required.
---v2
-adding native_422 field as 0 [Vandita]
-filling in second_line_bpg_offset, second_line_offset_adj
and nsl_bpg_offset in vds_cfg when native_420 is true
---v3
-adding display version check to solve igt issue
--v7
-remove is_pipe_dsc check as its always true for D14 [Jani]
--v10
-keep sink capability check [Jani]
-move from !(x == y || w == z) to x !=y && w != z [Jani]
--v11
-avoid native_420 computation if not gen14 [Uma]
--v12
-fix state mismatch issue of compressed_bpp
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230309062855.393087-6-suraj.kandpal@intel.com
On TGL+ the DSS control registers are at different offsets, and there's
one per pipe. Fix the offsets to fix dual link DSI for TGL+.
There would be helpers for this in the DSC code, but just do the quick
fix now for DSI. Long term, we should probably move all the DSS handling
into intel_vdsc.c, so exporting the helpers seems counter-productive.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8232
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230301151409.1581574-1-jani.nikula@intel.com
The DSI code has some local hacks to program TRANS_VBLANK on
TGL+ (ICL DSI transcoders didn't have this register). That
will not work when we need to start using the delayed vblank
(for DSB purposes). Too lazy to figure out what the is going
on there, so just sprinkle FIXMEs in the hopes someone else
will spot them eventually.
v2: Only TRANS_{HBLANK,SET_CONTEXT_LATENCY} still no not
exist for DSI transcoders, only TRANS_VBLANK
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-12-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Define the contents of the transcoder timing registers using
REG_GENMASK() & co. For ease of maintenance let's just define
the bitmasks with the full 16bit width (also used by the
current hand rolled stuff) even though not all bits are actually
used. None of the unsued bits have ever contained anything.
Jani spotted that the CRT load detection code did use narrower
bitmasks, so that is now going to change. But that is fine
since any garbage in the high bits would have been caught by
the state checker that always used the full 16bit masks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-10-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Rename PIPECONF to TRANSCONF to make it clear what it actually
applies to.
While the usual convention is to pick the earliers name I think
in this case it's more clear to use the later name. Especially
as even the register offset is in the wrong range (0x70000 vs.
0x60000) and thus makes it look like this is per-pipe.
There is one place in gvt that's doing something with TRANSCONF
while iterating with for_each_pipe(). So that might not be doing
the right thing for TRANSCODER_EDP, dunno. Not knowing what it
does I left it as is to avoid breakage.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Name the CPU transcoder timing registers TRANS_FOO rather than
just FOO. This is the modern name, after the pipe/transcoder split
happened. Makes it a bit more obvious whether you pass in a pipe or
a transcoder.
PIPESRC is a bit special as it's a pipe register, even though it
lives in the transcoder registers range (0x60000 instead of 0x70000).
And BCLRPAT I suppose is a transcoder register (since it has something
to do with the timing generator), but it doesn't even exist after gen4
so I left it to use the only name it ever had in bspec.
And while at it let's pass in the correct enum in few more
places why don't we. Although in all those places the distinction
doesn't matter.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We now have some eDP+DSI dual panel systems floating around
where the DSI panel is the secondary LFP and thus needs to
consult "panel type 2" in VBT in order to locate all the
other panel type dependant stuff correctly.
To that end we need to pass in the devdata to
intel_bios_init_panel_late(), otherwise it'll just assume
we want the primary panel type. So let's try to just populate
the vbt.ports[] stuff and encoder->devdata for icl+ DSI
panels as well.
We can't do this on older platforms as there we risk a DSI
port aliasing with a HDMI/DP port, which is a totally legal
thing as the DSI ports live in their own little parallel
universe.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8016
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230207064337.18697-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
It's a bit confusing to have two cached EDIDs in struct intel_connector
with slightly different purposes. Make the distinction a bit clearer by
moving the EDID cached for eDP and LVDS panels at connector init time to
struct intel_panel, and name it fixed_edid. That's what it is, a fixed
EDID for the panels.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/328350ef918638928a8286cdbab3107c8258332d.1674643465.git.jani.nikula@intel.com
Lots of ADL machines out there with bogus VBTs that declare
two eDP child devices. In order for those to work we need to
figure out which power sequencer to use before we try the EDID
read. So let's do the panel VBT init early if we can, falling
back to the post-EDID init otherwise.
The post-EDID init panel_type=0xff approach of assuming the
power sequencer should already be enabled doesn't really work
with multiple eDP panels, and currently we just end up using
the same power sequencer for both eDP ports, which at least
confuses the wakeref tracking, and potentially also causes us
to toggle the VDD for the panel when we should not.
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221125173156.31689-3-ville.syrjala@linux.intel.com
Turns out many of the files that need i915_reg.h get it implicitly via
{display/intel_de.h, gt/intel_context.h} -> i915_trace.h -> i915_irq.h
-> i915_reg.h. Since i915_trace.h doesn't actually need i915_irq.h,
makes sense to drop it, but that requires adding quite a few new
includes all over the place.
Prefer including i915_reg.h where needed instead of adding another
implicit include, because eventually we'll want to split up i915_reg.h
and only include the specific registers at each place.
Also some places actually needed i915_irq.h too.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e78a2e0ac1bffaf5af3b5ccc21dff05e6518cef.1668008071.git.jani.nikula@intel.com
All the connectors are zero initialized so no need to clear
the *_allowed flags we don't support. Only leave the ones we want
to set. And while at it switch to booleans instead of ints.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Consolidate the scaling_mode property setup into a single
place.
The one slight complicateion here is that GMCH platforms can't
do the CENTER mode except on the LVDS port. But we can deal with
that by just checking the connector type.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-12-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Currently, pic_height of vdsc_cfg structure is being used to calculate
slice_height, before it is set for DP.
So taking out the lines to set pic_height from the helper
intel_dp_dsc_compute_params() to individual encoders, and setting
pic_height, before it is used to calculate slice_height for DP.
Fixes: 5a6d866f8e ("drm/i915: Get slice height before computing rc params")
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220902103219.1168781-1-ankit.k.nautiyal@intel.com
Declutter i915_reg.h by splitting backlight registers to a separate
file. Also include the utility pin definitions, even though they are
used for non-backlight things too.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220815094838.3511723-1-jani.nikula@intel.com
Each LFP may have different panel type which is stored in LFP data
data block. Based on the child device index respective panel-type/
panel-type2 field will be used.
v1: Initial rfc verion.
v2: Based on review comments from Jani,
- Used panel-type instead addition panel-index variable.
- DEVICE_HANDLE_* name changed and placed before DEVICE_TYPE_*
macro.
v3:
- passing intel_bios_encoder_data as argument of
intel_bios_init_panel(). Passing NULL to indicate encoder is not
initialized yet for dsi as current focus is to enable dual EDP. [Jani]
v4:
- encoder->devdata used which is initialized before from vbt
structure. [Jani]
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220620065138.5126-1-animesh.manna@intel.com
Apparently when the VBT panel_type==0xff we should trawl through
the PNPID table and check for a match against the EDID. If a
match is found the index gives us the panel_type.
Tried to match the Windows behaviour here with first looking
for an exact match, and if one isn't found we fall back to
looking for a match w/o the mfg year/week.
v2: Rebase due to vlv_dsi changes
v3: Adjust to .get_panel_type() vfunc
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5545
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510104242.6099-14-ville.syrjala@linux.intel.com
Move the panel specific VBT parsing to happen during the
output probing stage. Needs to be done because the VBT
parsing will need to look at the EDID to determine
the correct panel_type on some machines.
We split the parsed VBT data (i915->vbt) along the same
boundary. For the moment we just hoist all the panel
specific stuff into connector->panel.vbt since that seems
like the most convenient place for eg. the backlight code.
Note that we simply drop the drrs type check from
intel_drrs_frontbuffer_update() since that operates on the whole
device rather than a specific connector/encoder. But the check
was just a micro optimization so removing it doesn't actually
mattter for correctness.
TODO: Lot's of cleanup to be done in the future. Eg. most of
the DSI stuff could probably be eliminated entirely and just
parsed on demand during DSI init.
v2: Note the intel_drrs_frontbuffer_update() change
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510104242.6099-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
drm/i915 feature pull #2 for v5.19:
Features and functionality:
- Add first set of DG2 PCI IDs for "motherboard down" designs (Matt Roper)
- Add initial RPL-P PCI IDs as ADL-P subplatform (Matt Atwood)
Refactoring and cleanups:
- Power well refactoring and cleanup (Imre)
- GVT-g refactor and mdev API cleanup (Christoph, Jason, Zhi)
- DPLL refactoring and cleanup (Ville)
- VBT panel specific data parsing cleanup (Ville)
- Use drm_mode_init() for on-stack modes (Ville)
Fixes:
- Fix PSR state pipe A/B confusion by clearing more state on disable (José)
- Fix FIFO underruns caused by not taking DRAM channel into account (Vinod)
- Fix FBC flicker on display 11+ by enabling a workaround (José)
- Fix VBT seamless DRRS min refresh rate check (Ville)
- Fix panel type assumption on bogus VBT data (Ville)
- Fix panel data parsing for VBT that misses panel data pointers block (Ville)
- Fix spurious AUX timeout/hotplug handling on LTTPR links (Imre)
Merges:
- Backmerge drm-next (Jani)
- GVT changes (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87bkwbkkdo.fsf@intel.com
DSC is the Display Stream Compression standard for DisplayPort. Move
the DSC code into display/ and split the header into files for protocol
core and DRM helpers. Adapt all users of the code. No functional
changes.
To avoid the proliferation of Kconfig options, DSC is part of DRM's
support for DisplayPort. If necessary, a new option could make DSC an
independent feature.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-6-tzimmermann@suse.de
