The Bspec does not mention polling the FEC Enable
Live status bit. That is only there for debug purposes.
So remove the polling from driver.
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201125072634.27664-1-manasi.d.navare@intel.com
Lspcon has Infoframes as well as DIP for HDR metadata(DRM Infoframe).
Create a separate mechanism for lspcon compared to HDMI in order to
address the same and ensure future scalability.
v2: Streamlined this as per Ville's suggestions, making sure that
HDMI infoframe versions are directly returned instead of a redundant
and confusing DIP overhead.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130204738.2443-12-uma.shankar@intel.com
Skip iterating over bigjoiner slaves, only the master has the state we
care about.
Add the width of the bigjoiner slave to the reconstructed fb.
Hide the bigjoiner slave to userspace, and double the mode on bigjoiner
master.
And last, disable bigjoiner slave from primary if reconstruction fails.
v3:
* Fix the ddi_get_config slave error (Ankit Nautiyal)
v2:
* Unsupported bigjoiner config for initial fb (Ville)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
[vsyrjala:
* Don't do any hw->uapi state copy for bigjoiner slave
* We still have hw.mode so no need to pass it in
* Appease checkpatch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-7-manasi.d.navare@intel.com
Enabling is done in a special sequence and so should plane updates
be. Ideally the end user never notices the second pipe is used.
This way ideally everything will be tear free, and updates are
really atomic as userspace expects it.
This uses generic modeset_enables() calls like trans port sync
but still has special handling for disable since for slave we
should not disable things like encoder, plls that are not enabled
for slave.
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
[vsyrjala: Appease checkpatch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-6-manasi.d.navare@intel.com
Make vdsc work when no output is enabled. The big joiner needs VDSC
on the slave, so enable it and set the appropriate bits.
So remove encoder usage from dsc functions.
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-5-manasi.d.navare@intel.com
I totally fumbled the ?: usage when generating the DDI encoder
names. Reverse the things that need reversing, and to make it
a bit less messy add a few macros to hide the arithmetic on the
port enums.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Fixes: 2d709a5a62 ("drm/i915: Give DDI encoders even better names")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117154028.8516-1-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Currently the DPLL .get_freq() uses pll->state.hw_state which
is not the thing we actually read out (except during driver
load/resume). Outside of that pll->state.hw_state is just the
thing we committed last time around. During state check we
just read the thing into crtc_state->dpll_hw_state, so that
is what we should use for calculating the DPLL output frequency.
I think we used to do this so that the results of the readout
were actually used, but somehow it got changed when the
.get_freq() refactoring happened.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201109231239.17002-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
JSL has update in vswing table for eDP.
BSpec: 21257
Changes since V1:
- Fixed few checkpatch errors
Cc: Souza Jose <jose.souza@intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020053657.99890-1-tejaskumarx.surendrakumar.upadhyay@intel.com
DG1 uses 2 registers for the ddi clock mapping, with PHY A and B using
DPCLKA_CFGCR0 and PHY C and D using DPCLKA1_CFGCR0. Hide this behind a
single macro that chooses the correct register according to the phy
being accessed, use the correct bitfields for each pll/phy and implement
separate functions for DG1 since it doesn't share much with ICL/TGL
anymore.
The previous values were correct for PHY A and B since they were using
the same register as before and the bitfields were matching.
v2: Add comment and try to simplify DG1_DPCLKA* macros by reusing
previous ones
v3:
- Fix DG1_DPCLKA_CFGCR0_DDI_CLK_SEL_MASK() after wrong macro reuse
- Move phy -> id map to a separate macro (Aditya)
- Remove DG1_DPCLKA_CFGCR0_DDI_CLK_SEL_MASK where not required
(Aditya)
- Use drm_WARN_ON
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Aditya Swarup <aditya.swarup@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201106210006.837953-1-lucas.demarchi@intel.com
Let's pimp the DDI encoder->name to reflect what the spec calls them.
Ie. on pre-tgl DDI A-F, on tgl+ DDI A-C or DDI TC1-6.
Also since each encoder is really a combination of the DDI and the PHY
we include the PHY name as well.
ICL is a bit special since it already has the two different types
of DDIs (combo or TC) but it still calls them just DDI A-F regarless
of the type. For that let's add an extra "(TC)" note to remind
is which type of DDI it really is.
The code is darn ugly, but not sure there's much we can do about it.
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-4-ville.syrjala@linux.intel.com
DG1 has one more combo phy port, no TC and all irq handling goes through
SDE, like for MCC.
v2: Also change intel_hpd_pin_default() to include DG1 mapping
v3, v4: Rebase on hpd refactor
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201021082034.3170478-2-lucas.demarchi@intel.com
Rename intel_dp_sink_dpms() to intel_dp_set_power()
so one doesn't always have to convert from the DPMS
enum values to the actual DP D-states.
Also when dealing with a branch device this has nothing to
do with any sink, so the old name was nonsense anyway.
Also adjust the debug message accordingly, and pimp it
with the standard encoder id+name thing.
Trivial bits done with cocci:
@@
expression DP;
@@
(
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_OFF)
+ intel_dp_set_power(DP, DP_SET_POWER_D3)
|
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_ON)
+ intel_dp_set_power(DP, DP_SET_POWER_D0)
)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Recently we came across requirement to identify EHL and JSL
platform to program them differently. Thus Split the basic
platform definition, macros, and PCI IDs to differentiate
between EHL and JSL platforms. Also, IS_ELKHARTLAKE is replaced
with IS_JSL_EHL everywhere.
Changes since V1 :
- Rebased to avoid merge conflicts
- Added missed check for jasperlake in intel_uc_fw.c
Cc : Matt Roper <matthew.d.roper@intel.com>
Cc : Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201013192948.63470-1-tejaskumarx.surendrakumar.upadhyay@intel.com
An LTTPR can be trained with training pattern 4 even if the DPCD
revision is < 1.4, but drm_dp_training_pattern_mask() would change
pattern 4 to pattern 3 on those DPCD revisions.
Since intel_dp_training_pattern() makes already sure that the proper
training pattern is used, all that needs to be masked out is the
scrambling disable flag, which is or'd to the mask later based on the
training pattern.
v2:
- Use a helper instead of open-coding the masking. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-2-imre.deak@intel.com
Extend the eDP panel power cycle delay wait on reboot handling
to cover all platforms. No reason to think that VLV/CHV are
in any way special since the documentation states that the
hardware power cycle delay goes back to its default value on
reset, and that may not be enough for all panels.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001151640.14590-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Recent update in documentation defeatured eDP HBR3 for EHL and JSL.
v2:
- Remove dead code in ehl_get_combo_buf_trans()
v3:
- Rebase
BSpec: 32247
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005175447.93430-1-jose.souza@intel.com
Atm, if a full modeset is performed during the initial modeset the link
training will happen with uninitialized max DP rate and lane count. Make
sure the corresponding encoder state is initialized by adding an encoder
hook called during driver init and system resume.
A better alternative would be to store all states in the CRTC state and
make this state available for the link re-training code. Also instead of
the DPCD read in the hook there should be really a proper sink HW
readout in place. Both of these require a bigger rework, so for now opting
for this minimal fix to make at least full initial modesets work.
The patch is based on
https://patchwork.freedesktop.org/patch/101473/?series=10354&rev=3
v2: (Ville)
- s/sanitize_state/sync_state/
- No point in calling the hook when CRTC is disabled, remove the call.
- No point in calling the hook for MST, remove it.
v3: Check only DPCD_REV to avoid clobbering intel_dp->dpcd. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005230154.1477653-1-imre.deak@intel.com
Move the checks to decide whether a fastset is possible during the
initial commit to an encoder hook. This check is really encoder specific
and the next patch will also require this adding a DP encoder specific
check.
v2: Fix negated condition in gen11_dsi_initial_fastset_check().
v3: Make sure to call the hook for all encoders on the crtc. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005215311.1475666-1-imre.deak@intel.com
On HP 800 G4 DM, if HDMI cable isn't plugged before boot, the HDMI port
becomes useless and never responds to cable hotplugging:
[ 3.031904] [drm:lspcon_init [i915]] *ERROR* Failed to probe lspcon
[ 3.031945] [drm:intel_ddi_init [i915]] *ERROR* LSPCON init failed on port D
Seems like the lspcon chip on the system only gets powered after the
cable is plugged.
Consilidate lspcon_init() into lspcon_resume() to dynamically init
lspcon chip, and make HDMI port work.
v6:
- Rebase on latest for-linux-next.
v5:
- Consolidate lspcon_resume() with lspcon_init().
- Move more logic into lspcon code.
v4:
- Trust VBT in intel_infoframe_init().
- Init lspcon in intel_dp_detect().
v3:
- Make sure it's handled under long HPD case.
v2:
- Move lspcon_init() inside of intel_dp_hpd_pulse().
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/203
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200610075542.12882-1-kai.heng.feng@canonical.com
Now that we've plumbed the crtc state all the way down we can
eliminate the DP_TP_{CTL,STATUS} register offsets from intel_dp,
and instead we derive them directly from the crtc state.
And thus we can get rid of the nasty hack in intel_ddi_get_config()
which mutates intel_dp during the readout.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-12-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Get rid of mode crtc->config usage, and some ad-hoc intel_dp state
usage by plumbing the crtc state all the way down to the link training
code.
Unfortunately we do have to keep some cached state in intel_dp so
that we can do the "does the link need retraining?" checks from
the short hpd handler.
v2: Add intel_crtc_state forward declaration
v3: Don't kill the PHY test code totally since it's
now in the hotplug work where we can get at the states
v4: Don't resurrect the debug scrambling disable bit (Imre)
Use intel_dp_mst_is_master_trans() (Imre)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001111053.24451-1-ville.syrjala@linux.intel.com
The HDMI vs. not-HDMI check got inverted whem the bogus encoder->type
checks were eliminated. So now we're using 0 as the link rate on DP
and potentially non-zero on HDMI, which is exactly the opposite of
what we want. The original bogus check actually worked more correctly
by accident since if would always evaluate to true. Due to this we
now always use the RBR/HBR1 vswing table and never ever the HBR2+
vswing table. That is probably not a good way to get a high quality
signal at HBR2+ rates. Fix the check so we pick the right table.
Cc: stable@vger.kernel.org
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Fixes: 94641eb6c6 ("drm/i915/display: Fix the encoder type check")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200930223642.28565-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
DP 1.3 adds some extra control knobs for DP->HDMI protocol conversion.
Let's use that to configure the "HDMI mode" (ie. infoframes vs. not)
based on the capabilities of the sink.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-13-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Non-HDMI sinks shouldn't be sent infoframes. Check for that when
using LSPCON.
FIXME: How do we turn off infoframes once enabled? Do we even
have to?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-3-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make a clean split between hpd pins for DDI vs. TC. This matches
how the actual hardware is split.
And with this we move the DDI/PHY->HPD pin mapping into the encoder
init instead of having to remap yet again in the interrupt code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-11-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Currently DP/HDMI/DDI encoders init their hpd_pin from the
connector init. Let's move it to the encoder init so that
we don't need to add platform specific junk to the connector
init (which is shared by all g4x+ platforms).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-10-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9VerweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGhc4H/iHD6qLdB36gZB6K
oc2nJyrqyWitv4ti2Mnt5PA7o4wX4l6nnr1QvoaJ4BRs5Ja1czRvb2XDmdzqAoIA
xITGoafqaAeDfxQ91bWrJsVN0pCRKiGwddXlU7TWmqw/riAkfOqi6GYKvav4biJH
+n1mUPQb1M2IbRFsqkAS+ebKHq3CWaRvzKOEneS88nGlL5u31S9NAru8Ru/fkxRn
6CwGcs1XRaBPYaZAhdfIb0NuatUlpkhPC9yhNS9up6SqrWmK3m65vmFVng6H0eCF
fwn1jVztboY/XcNAi5sM9ExpQCql6WLQEEktVikqRDojC8fVtSx6W55tPt7qeaoO
Z6t4/DA=
=bcA4
-----END PGP SIGNATURE-----
Merge tag 'v5.9-rc4' into drm-next
Backmerge 5.9-rc4 as there is a nasty qxl conflict
that needs to be resolved.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reusing icl_get_combo_buf_trans() for eDP was causing the wrong table
being used when the eDP port don't support low power voltage swing table.
v2: Only use icl_combo_phy_ddi_translations_edp_hbr3 if low_vswing is
set as EHL combo phy supports HBR3 (Matt R)
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826201549.83658-2-jose.souza@intel.com
Reusing icl_get_combo_buf_trans() for eDP was causing the wrong table
being used when the eDP port don't support low power voltage swing table.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826201549.83658-1-jose.souza@intel.com
This new HBR2 table for TGL-U and TGL-Y is required to pass
DisplayPort compliance.
BSpec: 49291
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Khaled Almahallawy<khaled.almahallawy@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200807192629.64134-2-jose.souza@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
If HTI (also sometimes called HDPORT) is enabled at startup, it may be
using some of the PHYs and DPLLs making them unavailable for general
usage. Let's read out the HDPORT_STATE register and avoid making use of
resources that HTI is already using.
v2:
- Fix minor checkpatch warnings
v3:
- Just readout HDPORT_STATE register once during init and then parse it
later as needed.
- Add a 'has_hti' device info flag to track whether we should readout
HDPORT_STATE or not. We can skip the platform/flag tests later since
the hti_state in dev_priv will remain 0 for platforms it does not
apply to.
- Move PLL masking into icl_get_combo_phy_dpll() since at the moment
RKL is the only platform that has HTI. (Jose)
Bspec: 49189
Bspec: 53707
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716220551.2730644-5-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Hours Of Battery Life is a new GEN12+ power-saving feature that allows
supported motherboards to use a special voltage swing table for eDP
panels that uses less power.
So here if supported by HW, OEM will set it in VBT and i915 will try
to train link with HOBL vswing table if link training fails it fall
back to the original table.
intel_ddi_dp_preemph_max() was optimized to only check the HOBL flag
instead of do something like is done in intel_ddi_dp_voltage_max()
because it is only called after the first entry of the voltage swing
table was loaded so the HOBL flag is valid at that point.
v3:
- removed a few parameters of icl_ddi_combo_vswing_program() that
can be taken from encoder
v4:
- using the HOBL vswing table until training fails completely (Ville)
v5:
- not reducing lane or link rate when link training fails with HOBL
active
- duplicated the HOBL voltage swing entry to match DP spec requirement
v6:
- removed the optional VS 3 & pre-emp 0 from HOBL table
- changed from u8:1 to bool to store hobl_failed/active
BSpec: 49291
BSpec: 49399
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200715175637.33763-1-jose.souza@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
