Add the necessary structures and functions to handle reading and
unpacking Adaptive Sync Secondary Data Packets. Also add support
to write and pack AS SDP.
--v2:
- Correct use of REG_BIT and REG_GENMASK. [Jani]
- Use as_sdp instead of async. [Jani]
- Remove unrelated comments and changes. [Jani]
- Correct code indent. [Jani]
--v3:
- Update definition names for AS SDP which are starting from
HSW, as these defines are applicable for ADLP+.(Ankit)
--v4:
- Remove as_sdp_mode from crtc_state.
- Drop metadata keyword.
- For consistency, update ADL_ prefix or post fix as required.
--v5:
- Check if AS_SDP bit is set in crtc_state->infoframes.enable. If not
return.
- Check for HAS_AS_SDP() before setting VIDEO_DIP_ENABLE_AS_ADL mask.
--v6:
- Rename intel_read_dp_infoframe_as_sdp to intel_read_dp_as_sdp.
--v7:
- Add read back for length and vtotal correction.
--v8:
- Use as_sdp->target_rr & 0xFF.
- Shift by 8 instead of 32, and drop casting to u64.
- Remove changes which are does not belong to this patch.
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322031157.3823909-5-mitulkumar.ajitkumar.golani@intel.com
Rename hdcp_capable and hdcp_2_2_capable to hdcp_get_capability
and hdcp_2_2_get_capability to properly reflect what these functions
are doing.
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240223081453.1576918-7-suraj.kandpal@intel.com
As described in the previous two patches an unexpected connector
detection can happen during the init/shutdown sequences. Prevent these
by returning the connector's current status from the detection handlers.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-10-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
After an HPD IRQ storm on a connector intel_hpd_irq_storm_detect() will
set the connector's HPD pin state to HPD_MARK_DISABLED and the IRQ gets
disabled. Subsequently intel_hpd_irq_storm_switch_to_polling() will
enable polling for these connectors, setting the pin state to
HPD_DISABLED, but only if the connector's base.polled field is set to
DRM_CONNECTOR_POLL_HPD. intel_hpd_irq_storm_reenable_work() will
reenable the IRQ - after 2 minutes - if the pin state is HPD_DISABLED.
The connectors will be created with their base.polled field set to 0,
which gets initialized only later in i915_hpd_poll_init_work() (using
intel_connector::polled). If a storm is detected on a connector after
it's created and IRQs are enabled on it - by intel_hpd_init() - and
before its bease.polled field is initialized in the above work, the
connector's HPD pin will stay in the HPD_MARK_DISABLED state - leaving
the IRQ disabled indefinitely - and polling will not get enabled on it as
intended.
I can't see a reason for initializing base.polled in a delayed manner,
so do this already when creating the connector, to prevent the above
race condition.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-2-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
We need to configure VSC Select field in video dip ctl if we want to have
e.g. colorimetry date in our VSC SDP.
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Shawn Lee <shawn.c.lee@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231220103609.1384523-8-jouni.hogander@intel.com
Apparently some BXT/GLK systems have DSI panels whose timings
don't agree with the normal cpu transcoder hblank>=32 limitation.
This is perhaps fine as there are no specific hblank/etc. limits
listed for the BXT/GLK DSI transcoders.
Move those checks out from the global intel_mode_valid() into
into connector specific .mode_valid() hooks, skipping BXT/GLK
DSI connectors. We'll leave the basic [hv]display/[hv]total
checks in intel_mode_valid() as those seem like sensible upper
limits regardless of the transcoder used.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9720
Fixes: 8f4b1068e7 ("drm/i915: Check some transcoder timing minimum limits")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127145028.4899-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We are asked to reprogram PEG_BAND_GAP_DATA prior to enabling
hotplug detection on the g45 HDMI/DP ports. Currently we do said
reprogamming from the DP/HDMI connector initialization functions.
That code should be mostly platform agnostic so clearly not the
best place for this. Move the workaround to the place where we
actually enable HPD detection.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231012124033.26983-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Remove the i915 specific i2c-N symlink from HDMI connectors.
This was added to sort of mirror the DP connectors that alreayd
had their aux ch based i2c adapter sitting beneath them in the
sysfs hierarchy. But now that we have the standard "ddc" symlink
approach provided by the core let's switch to that fully.
I don't think anything beyond igt depends on this.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230829113920.13713-12-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Remove the mostly redundant hdmi->ddc_bus. The only thing that needs
it anymore is get_encoder_by_ddc_bus(), but that can be replaced with
a slight detour through attached_connector+intel_gmbus_get_adapter().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230829113920.13713-11-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Rename the various names we've used for the DDC bus
i2c adapter ("i2c", "adapter", etc.) to just "ddc".
This differentiates it from the various other i2c
busses we might have (DSI panel stuff, DVO control bus, etc.).
v2: Don't add a bogus drm_get_edid() call (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230831104300.29688-1-ville.syrjala@linux.intel.com
Use intel_connector as argument instead of intel_digital_port in
hdcp_2_2_capable function and dig_port can be later derived from
connector. This will help with getting the correct hdcp version of
particular monitor in a MST setup.
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830073437.666263-2-suraj.kandpal@intel.com
Update intel_hdcp_shim funcs specifically read_2_2_message,
write_2_2_message and config_stream_type to use intel_connector
argument instead of intel_digital_port as this will help in getting
correct aux later for dp mst scenarios also already hdcp funcs
derive digital_port from connector and then many funcs again get back
the connector from dig_port which doesn't seem right.
Connector specific hdcp functions can derive dig_port on need basis.
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230828063401.600414-2-suraj.kandpal@intel.com
The issue fixed in
commit a8ddac7c9f ("drm/i915: Avoid HPD poll detect triggering a new detect cycle")
on VLV, CHV is still present on platforms where the display hotplug
detection functionality is available whenever the device is in D0 state
(hence these platforms switch to HPD polling only when the device is
runtime suspended).
The above commit avoids an endless i915_hpd_poll_init_work() ->
connector detect loop by making sure that by the end of
i915_hpd_poll_init_work() all display power references acquired by the
connector detect functions which can trigger a new cycle (display core
power domain) are dropped. However on platforms where HPD polling is
enabled/disabled only from the runtime suspend/resume handlers, this is
not ensured: for instance eDP VDD, TypeC port PHYs and the runtime
autosuspend delay may still keep the device runtime resumed (via a power
reference acquired during connector detection and hence result in an
endless loop like the above).
Solve the problem described in the above commit on all platforms, by
making sure that a i915_hpd_poll_init_work() -> connector detect
sequence can't take any power reference in the first place which would
trigger a new cycle, instead of relying on these power references to be
dropped by the end of the sequence.
With the default runtime autosuspend delay (10 sec) this issue didn't
happen in practice, since the device remained runtime resumed for the
whole duration of the above sequence. CI/IGT tests however set the
autosuspend delay to 0, which makes the problem visible, see References:
below.
Tested on GLK, CHV.
v2: Don't warn about a requeued work, to account for disabling
polling directly during driver loading, reset and system resume.
References: https://gitlab.freedesktop.org/drm/intel/-/issues/7940#note_1997403
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230809104307.1218058-1-imre.deak@intel.com
Stop with the VBT DDC pin sanitation, and instead just check
that the appropriate DDC pin is still available when initializing
a HDMI connector.
The reason being that we want to start initializing ports in
VBT order to deal with VBTs that declare child devices with
seemingly conflicting ports. As the encoder initialization can
fail for other reasons (at least for eDP+AUX) we can't know
upfront which way the conflicts should be resolved.
Note that the old way of sanitizing gave priority to the last
port declared in the VBT, but now we sort of do the opposite by
favoring the first encoder to successfully initialize. So far
we're not aware of HDMI/DDC use cases where this would matter
but for AUX CH (will be subject to a similar change) there are
known cases where it matters.
Also note that the old code fell back to the platform default DDC
pin if the VBT pin was populated but invalid. That doesn't seem like
such a great idea because the VBT might have later declared another
port using that platform default pin, and so we might just be
creating more DDC pin conflicts here. So lets not second guess the
VBT and simply reject the entire HDMI encoder if the VBT DDC pin is
invalid.
v2: Pimp the commit message (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230630155846.29931-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Now that we have encoder->devdata everwhere we don't need
the intel_bios_is_port_dp_dual_mode() wrapper any more.
And while at it let's include it in the child device log
dump as well since the logic in there is a bit more complex
than just DP&&HDMI.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230509160206.25971-3-ville.syrjala@linux.intel.com
Acked-by: Gustavo Sousa <gustavo.sousa@intel.com>
On g4x the hardware has only one audio/video DIP block. Thus
only one HDMI port can transmit audio/infoframes at a time.
Currently we pretend that multiple ports can do it at the same
time, but that doesn't actually work for two reasons:
- the state of the single hw block will get clobbered by
the multiple ports, leading to state checker failures
- the hardware will automagically disable audio/infoframe
transmission when enabled on multiple ports
To fix this let's allow only one of the ports to transmit
audio/infoframes at a time. We'll just go over all the HDMI
ports and pick the first one that is otherwise capable of
audio/infoframes. Further HDMI ports will be treated as if
they had a DVI sink connected.
In order to compute this consistently we'll also need to
always add all HDMI ports to the atomic state.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221107194604.15227-6-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
We'll be wanting to compute has_hdmi_sink a bit differently
for some platforms. To that end compute it in the encoder
.compute_config_hook() before we call intel_hdmi_compute_config().
intel_hdmi_compute_has_hdmi_sink() will do the basic lifting
beyond any platform specific stuff.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221107194604.15227-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Start passing the sink_format, to all functions that take a bool
ycbcr420_output as parameter. This will make the functions generic,
and will serve as a slight step towards 4:2:2 support later.
v2: Rebased.
v3: Correct the checks in places concerned with pipe output. (Ville)
Other minor styling and refactoring fixes, as suggested by Ville.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427125605.487769-5-ankit.k.nautiyal@intel.com
The decision to use DFP output format conversion capabilities should be
during compute_config phase.
This patch adds new member to crtc_state to represent the final
output_format to the sink. In case of a DFP this can be different than
the output_format, as per the format conversion done via the PCON.
This will help to store only the format conversion capabilities of the
DP device in intel_dp->dfp, and use crtc_state to compute and store the
configuration for color/format conversion for a given mode.
v2: modified the new member to crtc_state to represent the final
output_format that eaches the sink, after possible conversion by
PCON kind of devices. (Ville)
v3: Addressed comments from Ville:
-Added comments to clarify difference between sink_format and
output_format.
-Corrected the order of setting sink_format and output_format.
-Added readout for sink_format in get_pipe_config hooks.
v4: Set sink_format for intel_sdvo too. (Ville)
v5: Rebased.
v6: Fixed condition to go for YCbCr420 format for dp and hdmi. (Ville)
v7: Fix the condition to set sink_format for HDMI.
Set hdmi output_format simply as sink_format. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v3)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427125605.487769-2-ankit.k.nautiyal@intel.com
Create a table for C20 DP1.4, DP2.0 and HDMI2.1 rates.
The PLL settings are based on table, not for algorithmic alternative.
For DP 1.4 only MPLLB is in use.
Once register settings are done, we read back C20 HW state.
BSpec: 64568
v2: Updated pll tables (RK)
MPLLB selection fix (RK)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-3-mika.kahola@intel.com
Like DG2, we still don't have a proper algorithm that can be used
for calculating PHY settings, but we do have tables of register
values for a handful of the more common link rates. Some support is
better than none, so let's go ahead and add/use these tables when we
can, and also add some logic to hdmi_port_clock_valid() to filter the
modelist to just the modes we can actually support with these link
rates.
Hopefully we'll have a proper / non-encumbered algorithm to calculate
these registers by the time we upstream and we'll be able to replace
this patch with something more general purpose.
Bspec: 64568
v2: Rebasing with Clint's HDMI C10 PLL tables (Mika)
v3: Remove the extra hdmi clock check pruning.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-8-radhakrishna.sripada@intel.com
Include the device and connector information in the SCDC
debugs. Makes it easier to figure out who did what.
v2: Rely on connector->ddc (Maxime)
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Robert Foss <rfoss@kernel.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Emma Anholt <emma@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230403223652.18848-1-ville.syrjala@linux.intel.com
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Rename PIPECONF to TRANSCONF to make it clear what it actually
applies to.
While the usual convention is to pick the earliers name I think
in this case it's more clear to use the later name. Especially
as even the register offset is in the wrong range (0x70000 vs.
0x60000) and thus makes it look like this is per-pipe.
There is one place in gvt that's doing something with TRANSCONF
while iterating with for_each_pipe(). So that might not be doing
the right thing for TRANSCODER_EDP, dunno. Not knowing what it
does I left it as is to avoid breakage.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Switch a lot of the intel_bios_foo() stuff to just accept the
devdata (VBT child device info) directly, instead of taking
detours via vbt.ports[].
Also unify the function naming scheme.
v2: Drop the redundant "encoder" from the dp/hdmi specific functions
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216000425.32216-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We always have encoder->devdata available on the platforms
that can have LSPCON. So let's start looking there instead
of digging it out from vbt.ports[].
And let's rename the function to fit the common pattern
for these things.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
There are cases, where devices have an HDMI1.4 retimer, and TMDS clock rate
is capped to 340MHz via VBT. In such cases scrambling might be supported
by the platform and an HDMI2.0 sink for lower TMDS rates, but not
supported by the retimer, causing blankouts.
So avoid enabling scrambling, if the TMDS clock is capped to <= 340MHz.
v2: Added comment, documenting the rationale to check for TMDS clock,
before going for scrambling. (Arun)
v3: Fixed the function name to check if source supports scrambling. (Jani)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221222040851.3029514-1-ankit.k.nautiyal@intel.com
Convert all the connectors that use cached connector edid and
detect_edid to drm_edid.
Since drm_get_edid() calls drm_connector_update_edid_property() while
drm_edid_read*() do not, we need to call drm_edid_connector_update()
separately, in part due to the EDID caching behaviour in HDMI and
DP. Especially DP depends on the details parsed from EDID. (The big
behavioural change conflating EDID reading with parsing and property
update was done in commit 5186421cbf ("drm: Introduce epoch counter to
drm_connector"))
v6: Rebase on drm_edid_connector_add_modes()
v5: Fix potential uninitialized var use (kernel test robot <lkp@intel.com>)
v4: Call drm_edid_connector_update() after reading HDMI/DP EDID
v3: Don't leak vga switcheroo EDID in LVDS init (Ville)
v2: Don't leak opregion fallback EDID (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/eabb4de932841b38b34cc2818ea9fbf7c10224fd.1674643465.git.jani.nikula@intel.com
Stash the ELD into the crtc_state and precompute it. This gets
rid of the ugly ELD mutation during intel_audio_codec_enable(),
and opens the door for the state checker.
v2: Make another copy for the acomp hooks (Chaitanya)
Split out the bogus ELD handling change (Jani)
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-5-ville.syrjala@linux.intel.com
Defeature Display Interlace support.
Support for interlace modes is removed from Gen 12 onwards.
Pruning the interlace modes for HDMI for Display >=12.
Bspec: 50490
v2: Add check for both DP and HDMI. (Ville)
Get rid of redundant check for interlace mode in modevalid. (Ville)
v3: Simplify the condition to avoid interlace modes. (Jani)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230105124125.1129653-1-ankit.k.nautiyal@intel.com
Since the DP/HDMI connector do not set connector->doublescan_allowed,
the doublescan modes will get automatically filtered during
drm_helper_probe_single_connector_modes().
Therefore check for double scan modes is not required and is dropped
from modevalid functions for both DP and HDMI.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221017143038.1748319-2-ankit.k.nautiyal@intel.com
This patch introduces initial workarounds for mtl platform
v2: switch IS_MTL_DISPLAY_STEP to use IS_METEORLAKE from testing display
ver. (Tvrtko)
v3: clerical issues, extend 16015201720 to mtl. (MattR)
v4: make sure 16015201720 includes display 13. (MattR)
Bspec: 66624
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221209220543.502047-1-matthew.s.atwood@intel.com
Replace integrated with discrete for dgfx platforms.
v2: commit title reword (Jani)
v3: use variable name i915 (Jani)
v4: commit message reword (MattR)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Taylor, Clinton A <clinton.a.taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221129203343.720860-1-clinton.a.taylor@intel.com
When doing HDMI+non-HDMI cloning the other sink can't get
the infoframes/etc. so stuff like limited range output is
not a good idea.
Similarly when doing HDMI+HDMI cloning on g4x (only platform
where we allow it) only one of the ports can receive infoframes
and so again using any fancy stuff is a bad idea. We also don't
track the inforames/audio state per-port so we'd end up with
some kind of random mismash state when multipled encoders try
to compute the same stuff. And the hardware will in fact
automagically disable audio/infoframe transmission if you try
to enable it for multiple HDMI ports at the same time.
Thus disable all HDMI specific features when cloning.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221107194604.15227-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
