These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While add it, also remove commas after the sentinel entries.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240509174158.2211071-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some devices list 3 Gpio resources in the ACPI resource list for
the touchscreen:
1. GpioInt resource pointing to the GPIO used for the interrupt
2. GpioIo resource pointing to the reset GPIO
3. GpioIo resource pointing to the GPIO used for the interrupt
Note how the third extra GpioIo resource really is a duplicate
of the GpioInt provided info.
Ignore this extra GPIO, treating this setup the same as gpio_count == 2 &&
gpio_int_idx == 0 fixes the touchscreen not working on the Thunderbook
Colossus W803 rugged tablet and likely also on the CyberBook_T116K.
Reported-by: Maarten van der Schrieck
Closes: https://gitlab.com/AdyaAdya/goodix-touchscreen-linux-driver/-/issues/22
Suggested-by: Maarten van der Schrieck
Tested-by: Maarten van der Schrieck
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231223141650.10679-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add a special case for gpio_count == 1 && gpio_int_idx == 0 to
goodix_add_acpi_gpio_mappings().
It seems that on newer x86/ACPI devices the reset and irq GPIOs are no
longer listed as GPIO resources instead there is only 1 GpioInt resource
and _PS0 does the whole reset sequence for us.
This means that we must call acpi_device_fix_up_power() on these devices
to ensure that the chip is reset before we try to use it.
This part was already fixed in commit 3de93e6ed2 ("Input: goodix - call
acpi_device_fix_up_power() in some cases") by adding a call to
acpi_device_fix_up_power() to the generic "Unexpected ACPI resources"
catch all.
But it turns out that this case on some hw needs some more special
handling. Specifically the firmware may bootup with the IRQ pin in
output mode. The reset sequence from ACPI _PS0 (executed by
acpi_device_fix_up_power()) should put the pin in input mode,
but the GPIO subsystem has cached the direction at bootup, causing
request_irq() to fail due to gpiochip_lock_as_irq() failure:
[ 9.119864] Goodix-TS i2c-GDIX1002:00: Unexpected ACPI resources: gpio_count 1, gpio_int_idx 0
[ 9.317443] Goodix-TS i2c-GDIX1002:00: ID 911, version: 1060
[ 9.321902] input: Goodix Capacitive TouchScreen as /devices/pci0000:00/0000:00:17.0/i2c_designware.4/i2c-5/i2c-GDIX1002:00/input/input8
[ 9.327840] gpio gpiochip0: (INT3453:00): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[ 9.327856] gpio gpiochip0: (INT3453:00): unable to lock HW IRQ 26 for IRQ
[ 9.327861] genirq: Failed to request resources for GDIX1002:00 (irq 131) on irqchip intel-gpio
[ 9.327912] Goodix-TS i2c-GDIX1002:00: request IRQ failed: -5
Fix this by adding a special case for gpio_count == 1 && gpio_int_idx == 0
which adds an ACPI GPIO lookup table for the int GPIO even though we cannot
use it for reset purposes (as there is no reset GPIO).
Adding the lookup will make the gpiod_int = gpiod_get(..., GPIOD_IN) call
succeed, which will explicitly set the direction to input fixing the issue.
Note this re-uses the acpi_goodix_int_first_gpios[] lookup table, since
there is only 1 GPIO in the ACPI resources the reset entry in that
lookup table will amount to a no-op.
Reported-and-tested-by: Michael Smith <1973.mjsmith@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231003215144.69527-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Goodix touchscreen controller with ACPI ID GDX9110 was not recognized
by the goodix driver. This patch adds this ID to the list of supported IDs,
allowing the driver to be used with this device. The change will allow
Linux to be used on ~1 million tablet devices used in Kenyan primary
schools.
Signed-off-by: Felix Engelhardt <felix.engelhardt@eidu.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230807124723.382899-1-felix.engelhardt@eidu.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmSYzfYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/ucH/iOM/1Py/fSg0qSs
7NJ4XXlourT5zrnRMom3cm3d9gYqgTzgvKFL3kjMEexTRVYbhlcO4ZPRsiry8zxF
ToGX+V8tDMqb8WSdFHzkljRY+zDRyfEUDMlTzROAD9DunLmQtkJKyrggkeGdjkpP
OyfGqKpwlLXZRAXBil/U8Mx9MHdjJubloZwghLZr33VdUZa68+JJ9l6w163Oe/ET
K264NM0wxN/kvN57JvePgqMccQwpINylg8IhRI+XelgczjUXeJBsOA8TDv4bDN4Q
bjCLhkWbIaZtTYqvOXa/kD0T8wd7KETsMBQN8YzyDh6W0GmAlJjTawyAhA6jA5in
x3uz2W8=
=L3zp
-----END PGP SIGNATURE-----
Merge tag 'v6.4' into next
Sync up with mainline to bring in updates to shared infrastructure.
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230625162817.100397-14-krzysztof.kozlowski@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517164645.162294-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Android Lenovo Yoga Book X90F / X90L uses the same goodix touchscreen
with 9 bytes touch reports for its touch keyboard as the already supported
Windows Lenovo Yoga Book X91F/L, add a DMI match for this to
the nine_bytes_report DMI table.
When the quirk for the X91F/L was initially added it was written to
also apply to the X90F/L but this does not work because the Android
version of the Yoga Book uses completely different DMI strings.
Also adjust the X91F/L quirk to reflect that it only applies to
the X91F/L models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20230315134442.71787-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmO7AjceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG8dEH/RS/6CnVCJENY9AL
Th4+zvSUhPfmiY6UdubijGD7v+qfK6UVOhuSNkVJ9QlLFYOTTenapNBzOTGg10ND
PCwYtllmVw8m7eT1/k83DPbxZexhe8+e6dW/ktNefj7vbnqRuARGqtP5123GHLVF
ztdcYKj8t3XIP2Pid2eMFWGARFQ0GJ1ubbieK6a2XcAuQCZfhy2gV8otl2zDZZQd
d/5+0vgIDUYkMVU5cYmM5JJmvvTzhRVJ8b75LVqICEOakbUdyzW6EmKNCBDcCM92
M6AHbwTd44zZeJIxoPF0rB6VXa3f+NCCEcdUzzZlhqnOq3zmE7wNRBIRnxCysguV
q+NdLuQ=
=tBAq
-----END PGP SIGNATURE-----
Merge tag 'v6.2-rc3' into next
Merge with mainline to bring in timer_shutdown_sync() API.
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection
against unused function warnings. The new combination of pm_sleep_ptr()
and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions,
thus suppressing the warning, but still allowing the unused code to be
removed. Thus also drop the __maybe_unused markings.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230102181842.718010-47-jic23@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221118224540.619276-242-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On ACPI systems (irq_pin_access_method == IRQ_PIN_ACCESS_ACPI_*) the driver
does not reset the controller at probe time, because sometimes the system
firmware loads a config and resetting might loose this config.
On the Nanote UMPC-01 device OTOH the config is in flash of the controller,
the controller needs a reset to load this; and the system firmware does not
reset the controller on a cold boot.
To fix the Nanote UMPC-01 touchscreen not working on a cold boot, try
resetting the controller and then re-reading the config when encountering
a config with 0 width/height/max_touch_num value and the controller has
not already been reset by goodix_ts_probe().
This should be safe to do in general because normally we should never
encounter a config with 0 width/height/max_touch_num. Doing this in
general not only avoids the need for a DMI quirk, but also might help
other systems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20221025122930.421377-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This controller is used by PinePhone and PinePhone Pro. Support for
the PinePhone Pro will be added in a later patch set.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Jarrah Gosbell <kernel@undef.tools>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220809091200.290492-1-kernel@undef.tools
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On ACPI boards, when we cannot get the GPIOs to do a reset ourselves
if necessary, call acpi_device_fix_up_power() to force the ACPI _PS0
method to run.
On some devices without proper GPIO descriptions this will reset
the touchscreen for us and this may be necessary for us to be able
to communicate to the touchscreen at all.
Specifically on an Aya Neo Next this change will cause the _PS0()
ACPI function to call INIT() which does:
Method (INIT, 0, Serialized)
{
TP_I = 0x00A50000
TP_R = 0x00A50000
Sleep (0x0A)
TP_I = 0x00E50000
Sleep (One)
TP_R = 0x00E50000
Sleep (0x06)
TP_I = 0x00A50000
Sleep (0x3C)
TP_I = 0x00041800
}
On older kernels the ACPI core assumed a power-on was necessary by itself
and would run _PS0 before our probe function runs, which can be seen from
the GPIO pin ctrl registers in /sys/kernel/debug/gpio which match
the above hex values with older kernels.
With newer kernels before this change the GPIO pin ctrl registers do not
match, indicating INIT() has not run and probing the touchscreen fails.
This change makes Linux run _PS0() again fixing the touchscreen not working
on the Aya Neo Next.
Reported-and-tested-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220618210233.208027-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
No need to open code functionality that is provided by the
acpi_gpio_get_irq_resource() and acpi_gpio_get_io_resource().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220705180252.963-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmIuUskeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGCFkH/2n3mpGXuITp0ZXE
TNrpbdZOof5SgLw+w7THswXuo6m5yRGNKQs9fvIvDD8Vf7/OdQQfPOmF1cIE5+nk
wcz6aHKbdrok8Jql2qjJqWXZ5xbGj6qywg3zZrwOUsCKFP5p+AjBJcmZOsvQHjSp
ASODy1moOlK+nO52TrMaJw74a8xQPmQiNa+T2P+FedEYjlcRH/c7hLJ7GEnL6+cC
/R4bATZq3tiInbTBlkC0hR0iVNgRXwXNyv9PEXrYYYHnekh8G1mgSNf06iejLcsG
aAYsW9NyPxu8zPhhHNx79K9o8BMtxGD4YQpsfdfIEnf9Q3euqAKe2evRWqHHlDms
RuSCtsc=
=M9Nc
-----END PGP SIGNATURE-----
Merge tag 'v5.17-rc8' into next
Sync up with mainline to again get the latest changes in HID subsystem.
Because there is no way to detect if the touchscreen has pen support,
the driver is allocating and registering the input_pen input_dev on
receiving the first pen event.
But this means that the input_dev gets allocated after the request_irq()
call which means that the devm framework will free it before disabling
the irq, leaving a window where the irq handler may run and reference the
free-ed input_dev.
To fix this move the allocation of the input_pen input_dev to before
the request_irq() call, while still only registering it on the first pen
event so that the driver does not advertise pen capability on touchscreens
without it (most goodix touchscreens do not have pen support).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220131143539.109142-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the new input_copy_abs() helper and move the 2 input_abs_set_res()
calls up to be directly after the 2 input_copy_abs() calls, so that
the calls initializing the X and Y axis are all together.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220131143539.109142-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ACPI/x86 devices with a Cherry Trail SoC should have a GpioInt + a regular
GPIO ACPI resource in their ACPI tables.
Some CHT devices have a bug, where the also is bogus interrupt resource
(likely copied from a previous Bay Trail based generation of the device).
The i2c-core-acpi code will assign the bogus, non-working, interrupt
resource to client->irq. Add a workaround to fix this up.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=2043960
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220228111613.363336-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmHbZ+YeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGDs4H/RgC8JOV3Dki1VtO
6OwPxUKKojhVU9LJis7kyG5voB/zE7tK5nI+jC3gYGQUFKWaZ3YY8s3UcV1zvg/b
a44b91boA+dKxEwOq4RZNQ9mU+QWnNoG5+UqBkmB8vewi3QC3T8xEmpWcERLbU7d
KrI2T6i4ksJ9OYSYMEMyrvrpt7nt3n1tDX8b71faXjf1zbLeGo9zT53t6BJ/LknV
AK406Eq/3bg36OZrKFuG7hCJfRE/cSlxF9bxK3sIfMBMQ2YPe1S5+pxl5iBD0nyl
NaHOBYcLTxPAne3YgIvK0zDdsS+EtPSlaVdWfSmNjQhX2vqEixldgdrOCmwp37vd
3gV9D28=
=hrOo
-----END PGP SIGNATURE-----
Merge tag 'v5.16' into next
Sync up with mainline to bring in the latest API changes.
Pull input fixes from Dmitry Torokhov:
"A few small updates to drivers.
Of note we are now deferring probes of i8042 on some Asus devices as
the controller is not ready to respond to queries first time around
when the driver is compiled into the kernel"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elants_i2c - do not check Remark ID on eKTH3900/eKTH5312
Input: atmel_mxt_ts - fix double free in mxt_read_info_block
Input: goodix - fix memory leak in goodix_firmware_upload
Input: goodix - add id->model mapping for the "9111" model
Input: goodix - try not to touch the reset-pin on x86/ACPI devices
Input: i8042 - enable deferred probe quirk for ASUS UM325UA
Input: elantech - fix stack out of bound access in elantech_change_report_id()
Input: iqs626a - prohibit inlining of channel parsing functions
Input: i8042 - add deferred probe support
2 small fixes for pen support
1. Set the id.vendor field for the pen input_dev
2. Fix a typo in a comment
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211212124242.81019-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
goodix_get_gpio_config() errors are fatal (abort probe()) so log them
at KERN_ERR level rather then as debug messages.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211212124242.81019-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmF/AjYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1hkIAJ6sFDbvb4M4LMwf
Slh2NVL9o5sLMBDzVwnVlyMSKDbMn1WBKreGssaLgZjGDc74lxsdSmw5l9MZm0JN
xlq95Q6XFiuu+0qDHPWwfDz3JFO4TqW2ZLLPWk9NnkNbRXqccSrlVRi1RpgE1t3/
NUtS8CQLu6A2BYMc6mkk3aV6IwSNKOkWbM5eBHSvU4j8B6lLbNQop0AfO/wyY1xB
U6LiVE1RpN/b7Yv+75ITtNzuHzVIBx6305FvSnOlKbMKKvIClt96Vd2OeuoEkK+6
wGU8JraB1+fc0GckAhynNrjWQWdvi0MAhFWWEJxjS20OGcV1rXDduNfkVNauO1Zn
+dNyJ3s=
=g9fz
-----END PGP SIGNATURE-----
Merge tag 'v5.15' into next
Sync up with the mainline to get the latest APIs and DT bindings.
Add d->model mapping for the "9111" model, this fixes uses using
a wrong config_len of 240 bytes while the "9111" model uses
only 186 bytes of config.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206164747.197309-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unless the controller is not responding at boot or after suspend/resume,
the driver never resets the controller on x86/ACPI platforms. The driver
still requesting the reset pin at probe() though in case it needs it.
Until now the driver has always requested the reset pin with GPIOD_IN
as type. The idea being to put the pin in high-impedance mode to save
power until the driver actually wants to issue a reset.
But this means that just requesting the pin can cause issues, since
requesting it in another mode then GPIOD_ASIS may cause the pinctrl
driver to touch the pin settings. We have already had issues before
due to a bug in the pinctrl-cherryview.c driver which has been fixed in
commit 921daeeca9 ("pinctrl: cherryview: Preserve
CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs").
And now it turns out that requesting the reset-pin as GPIOD_IN also stops
the touchscreen from working on the GPD P2 max mini-laptop. The behavior
of putting the pin in high-impedance mode relies on there being some
external pull-up to keep it high and there seems to be no pull-up on the
GPD P2 max, causing things to break.
This commit fixes this by requesting the reset pin as is when using
the x86/ACPI code paths to lookup the GPIOs; and by not dropping it
back into input-mode in case the driver does end up issuing a reset
for error-recovery.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209061
Fixes: a7d4b17166 ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206091116.44466-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Just one new driver (Cypress StreetFighter touchkey), and no input
core changes this time.
Plus various fixes and enhancements to existing drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (54 commits)
Input: iforce - fix control-message timeout
Input: wacom_i2c - use macros for the bit masks
Input: ili210x - reduce sample period to 15ms
Input: ili210x - improve polled sample spacing
Input: ili210x - special case ili251x sample read out
Input: elantench - fix misreporting trackpoint coordinates
Input: synaptics-rmi4 - Fix device hierarchy
Input: i8042 - Add quirk for Fujitsu Lifebook T725
Input: cap11xx - add support for cap1206
Input: remove unused header <linux/input/cy8ctmg110_pdata.h>
Input: ili210x - add ili251x firmware update support
Input: ili210x - export ili251x version details via sysfs
Input: ili210x - use resolution from ili251x firmware
Input: pm8941-pwrkey - respect reboot_mode for warm reset
reboot: export symbol 'reboot_mode'
Input: max77693-haptic - drop unneeded MODULE_ALIAS
Input: cpcap-pwrbutton - do not set input parent explicitly
Input: max8925_onkey - don't mark comment as kernel-doc
Input: ads7846 - do not attempt IRQ workaround when deferring probe
Input: ads7846 - use input_set_capability()
...
Some Goodix touchscreen controllers, such as for example the GT912,
don't have flash-storage for their firmware.
These models require the OS to load the firmware at runtime, as well as
some other special handling. Add support for this to the goodix driver.
This patch was developed and tested on a Glavey TM800A550L tablet.
Note the "goodix,main-clk" and "firmware-name" device-properties used
by the new code are *not* documented in the
Documentation/devicetree/bindings/input/touchscreen/goodix.yaml
device-tree bindings for now.
Not documenting these is intentional. This is done because this code has
only been tested on x86/ACPI so far, where devicetree is not used.
Instead these properties are set through a software-fwnode attached to the
device by the drivers/platform/x86/touchscreen_dmi.c code. This means that
the use of this properties for now is purely a kernel-internal thing and
the name/working of the properties may still be changed for now.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-7-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The config which needs to be send to the controller on some device-models
is model-specific. Allow specifying a model-specific filename through
a device-property, rather then always using a fixed filename.
Note the "goodix,config-name" device-property used by this is
*not* documented in the
Documentation/devicetree/bindings/input/touchscreen/goodix.yaml
device-tree bindings for now.
Not documenting these is intentional. This is done because this code has
only been tested on x86/ACPI so far, where devicetree is not used.
Instead these properties are set through a software-fwnode attached to the
device by the drivers/platform/x86/touchscreen_dmi.c code. This means that
the use of this property for now is purely a kernel-internal thing and
the name/working of the property may still be changed for now.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-6-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make the goodix_i2c_read() and goodix_i2c_write*() helpers log errors
themselves. This allows removing all the error logging from their callers.
This already results in a nice cleanup with the current code and it also
helps to make the upcoming support for controllers without flash cleaner.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Refactor reset handling a bit, change the main reset handler
into a new goodix_reset_no_int_sync() helper and add a
goodix_reset() wrapper which calls goodix_int_sync()
separately.
Also push the dev_err() call on reset failure into the
goodix_reset_no_int_sync() and goodix_int_sync() functions,
so that we don't need to have separate dev_err() calls in
all their callers.
This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add a goodix.h header file, and move the register definitions,
and struct declarations there and add prototypes for various
helper functions.
This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.
Since MAINTAINERS needs updating because of this change anyways,
also add myself as co-maintainer.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Change the type of the goodix_i2c_write() len parameter to from 'unsigned'
to 'int' to avoid bare use of 'unsigned', changing it to 'int' makes
goodix_i2c_write()' prototype consistent with goodix_i2c_read().
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Move the DMI quirks for upside-down mounted Goodix touchscreens from
drivers/input/touchscreen/goodix.c to
drivers/platform/x86/touchscreen_dmi.c,
where all the other x86 touchscreen quirks live.
Note the touchscreen_dmi.c code attaches standard touchscreen
device-properties to an i2c-client device based on a combination of a
DMI match + a device-name match. I've verified that the: Teclast X98 Pro,
WinBook TW100 and WinBook TW700 uses an ACPI devicename of "GDIX1001:00"
based on acpidumps and/or dmesg output available on the web.
This patch was tested on a Teclast X89 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210504185746.175461-2-hdegoede@redhat.com
The Goodix GT9286 is a capacitive touch sensor IC based on GT1x.
This chip can be found on a number of smartphones, including the
F(x)tec Pro 1 and the Elephone U.
This has been tested on F(x)Tec Pro1 (MSM8998).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210109135512.149032-2-angelogioacchino.delregno@somainline.org
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen on the Teclast x98 Pro is also mounted upside-down in
relation to the display orientation.
Signed-off-by: Simon Beginn <linux@simonmicro.de>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20201117004253.27A5A27EFD@localhost
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/goodix.c:1168: warning: Function parameter or member 'ctx' not described in 'goodix_config_cb'
drivers/input/touchscreen/goodix.c:1168: warning: Excess function parameter 'ts' description in 'goodix_config_cb'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112110204.2083435-14-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
