Introduce n_regions in spi_nor_erase_map structure and remove
SNOR_LAST_REGION flag. Loop logics that depend on the flag are also
reworked to use n_regions as loop condition.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Suggested-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/eded84294bd81e966d6f423e578fc2cfb9a4a5b6.1708404584.git.Takahiro.Kuwano@infineon.com
[ta: update spi_nor_init_erase_cmd_list() and break the for loop sooner.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Encoding bitmask flags into offset worsen the code readability. The
erase type mask and flags should be stored in dedicated members. Also,
erase_map.uniform_erase_type can be removed as it is redundant.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Suggested-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/8e5e9e4081ed9f16ea9dce30693304a4b54d19b1.1708404584.git.Takahiro.Kuwano@infineon.com
[ta: remove spi_nor_region_end()]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
JESD216 mentions die erase, but does not provide an opcode for it.
Check BFPT dword 11, bits 30:24, "Chip Erase, Typical time", it says:
"Typical time to erase one chip (die). User must poll device busy to
determine if the operation has completed. For a device consisting of
multiple dies, that are individually accessed, the time is for each die
to which a chip erase command is applied."
So when a flash consists of a single die, this is the erase time for the
full chip (die) erase, and when it consists of multiple dies, it's the
die erase time. Chip and die are the same thing.
Add support for die erase. For now, benefit of the die erase when addr
and len are aligned with die size. This could be improved however for
the uniform and non-uniform erases cases to use the die erase when
possible. For example if one requests that an erase of a 2 die device
starting from the last 64KB of the first die to the end of the flash
size, we could use just 2 commands, a 64KB erase and a die erase.
This improvement is left as an exercise for the reader.
Tested-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20231125123529.55686-2-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Setting the status register write disable (SRWD) bit in the status
register (SR) with WP# signal of the flash left floating or wrongly tied to
GND (that includes internal pull-downs), will configure the SR permanently
as read-only. If WP# signal is left floating or wrongly tied to GND, avoid
setting SRWD bit while writing the SR during flash protection.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20230630142233.63585-3-amit.kumar-mahapatra@amd.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
* dt-bindings: Drop unneeded quotes
* mtdblock: Tolerate corrected bit-flips
* Use of_property_read_bool() for boolean properties
* Avoid magic values
* Avoid printing error messages on probe deferrals
* Prepare mtd_otp_nvmem_add() to handle -EPROBE_DEFER
* Fix error path for nvmem provider
* Fix nvmem error reporting
* Provide unique name for nvmem device
MTD device changes:
* lpddr_cmds: Remove unused words variable
* bcm63xxpart: Remove MODULE_LICENSE in non-modules
SPI NOR core changes:
* Introduce Read While Write support for flashes featuring several banks
* Set the 4-Byte Address Mode method based on SFDP data
* Allow post_sfdp hook to return errors
* Parse SCCR MC table and introduce support for multi-chip devices
SPI NOR manufacturer drivers changes:
* macronix: Add support for mx25uw51245g with RWW
* spansion:
- Determine current address mode at runtime as it can be changed in a
non-volatile way and differ from factory defaults or from what SFDP
advertises.
- Enable JFFS2 write buffer mode for few ECC'd NOR flashes: S25FS256T,
s25hx and s28hx
- Add support for s25hl02gt and s25hs02gt
Raw NAND core changes:
* Convert to platform remove callback returning void
* Fix spelling mistake waifunc() -> waitfunc()
Raw NAND controller driver changes:
* imx: Remove unused is_imx51_nfc and imx53_nfc functions
* omap2: Drop obsolete dependency on COMPILE_TEST
* orion: Use devm_platform_ioremap_resource()
* qcom:
- Use of_property_present() for testing DT property presence
- Use devm_platform_get_and_ioremap_resource()
* stm32_fmc2: Depends on ARCH_STM32 instead of MACH_STM32MP157
* tmio: Remove reference to config MTD_NAND_TMIO in the parsers
Raw NAND manufacturer driver changes:
* hynix: Fix up bit 0 of sdr_timing_mode
SPI-NAND changes:
* Add support for ESMT F50x1G41LB
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmRANmIACgkQJWrqGEe9
VoRU2QgAl8XFkLs1h88wGi6ln/MSK0cQJZWUzteGgWuaBQCMNfgGFzqPHyJ7ygO9
l4U4O1L/IvACvJx5QHm/lH5Mig23jym9J8YfV1Kf9aVYOlBKRNysbi+DdktESGG9
6HmpS0nQfkC84qA8ouInOp+AZYjFEPRrBfp5UWkSRHiQJvcYnt2iS2oOLk3LNY6y
zduBOno3mric2ZlBbg+ZCURhQzrr3k8c4VXV+LHSslqsmH/2sOFlg78hLJx922Y+
FTfYnx82iLIvFAJttRi2bXWKuE1Yr2XWJ3iEHKxmOA2vPmYi6mDBHTYhnikGSpm+
GhARHH+JhW7qzLbaq5ZC3HGH58aC/g==
=aYlo
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"Core MTD changes:
- dt-bindings: Drop unneeded quotes
- mtdblock: Tolerate corrected bit-flips
- Use of_property_read_bool() for boolean properties
- Avoid magic values
- Avoid printing error messages on probe deferrals
- Prepare mtd_otp_nvmem_add() to handle -EPROBE_DEFER
- Fix error path for nvmem provider
- Fix nvmem error reporting
- Provide unique name for nvmem device
MTD device changes:
- lpddr_cmds: Remove unused words variable
- bcm63xxpart: Remove MODULE_LICENSE in non-modules
SPI NOR core changes:
- Introduce Read While Write support for flashes featuring several
banks
- Set the 4-Byte Address Mode method based on SFDP data
- Allow post_sfdp hook to return errors
- Parse SCCR MC table and introduce support for multi-chip devices
SPI NOR manufacturer drivers changes:
- macronix: Add support for mx25uw51245g with RWW
- spansion:
- Determine current address mode at runtime as it can be changed
in a non-volatile way and differ from factory defaults or from
what SFDP advertises.
- Enable JFFS2 write buffer mode for few ECC'd NOR flashes:
S25FS256T, s25hx and s28hx
- Add support for s25hl02gt and s25hs02gt
Raw NAND core changes:
- Convert to platform remove callback returning void
- Fix spelling mistake waifunc() -> waitfunc()
Raw NAND controller driver changes:
- imx: Remove unused is_imx51_nfc and imx53_nfc functions
- omap2: Drop obsolete dependency on COMPILE_TEST
- orion: Use devm_platform_ioremap_resource()
- qcom:
- Use of_property_present() for testing DT property presence
- Use devm_platform_get_and_ioremap_resource()
- stm32_fmc2: Depends on ARCH_STM32 instead of MACH_STM32MP157
- tmio: Remove reference to config MTD_NAND_TMIO in the parsers
Raw NAND manufacturer driver changes:
- hynix: Fix up bit 0 of sdr_timing_mode
SPI-NAND changes:
- Add support for ESMT F50x1G41LB"
* tag 'mtd/for-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (55 commits)
mtd: nand: Convert to platform remove callback returning void
mtd: onenand: omap2: Drop obsolete dependency on COMPILE_TEST
mtd: spi-nor: spansion: Add support for s25hl02gt and s25hs02gt
mtd: spi-nor: spansion: Add a new ->ready() hook for multi-chip device
mtd: spi-nor: spansion: Rework cypress_nor_quad_enable_volatile() for multi-chip device support
mtd: spi-nor: spansion: Rework cypress_nor_get_page_size() for multi-chip device support
mtd: spi-nor: sfdp: Add support for SCCR map for multi-chip device
mtd: spi-nor: Extract volatile register offset from SCCR map
mtd: spi-nor: Allow post_sfdp hook to return errors
mtd: spi-nor: spansion: Rename method to cypress_nor_get_page_size
mtd: spi-nor: spansion: Enable JFFS2 write buffer for S25FS256T
mtd: spi-nor: spansion: Enable JFFS2 write buffer for Infineon s25hx SEMPER flash
mtd: spi-nor: spansion: Enable JFFS2 write buffer for Infineon s28hx SEMPER flash
mtd: spi-nor: spansion: Determine current address mode
mtd: spi-nor: core: Introduce spi_nor_set_4byte_addr_mode()
mtd: spi-nor: core: Update flash's current address mode when changing address mode
mtd: spi-nor: Stop exporting spi_nor_restore()
mtd: spi-nor: Set the 4-Byte Address Mode method based on SFDP data
mtd: spi-nor: core: Make spi_nor_set_4byte_addr_mode_brwr public
mtd: spi-nor: core: Update name and description of spi_nor_set_4byte_addr_mode
...
Infineon(Cypress) SEMPER NOR flash family has on-die ECC and its program
granularity is 16-byte ECC data unit size. JFFS2 supports write buffer
mode for ECC'd NOR flash. Provide a way to clear the MTD_BIT_WRITEABLE
flag in order to enable JFFS2 write buffer mode support.
A new SNOR_F_ECC flag is introduced to determine if the part has on-die
ECC and if it has, MTD_BIT_WRITEABLE is unset.
In vendor specific driver, a common cypress_nor_ecc_init() helper is
added. This helper takes care for ECC related initialization for SEMPER
flash family by setting up params->writesize and SNOR_F_ECC.
Fixes: c3266af101 ("mtd: spi-nor: spansion: add support for Cypress Semper flash")
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/d586723f6f12aaff44fbcd7b51e674b47ed554ed.1680760742.git.Takahiro.Kuwano@infineon.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Introduce a new (no SFDP) flag for the feature that we are about to
support: Read While Write. This means, if the chip has several banks and
supports RWW, once a page of data to write has been transferred into the
chip's internal SRAM, another read operation happening on a different
bank can be performed during the tPROG delay.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230328154105.448540-7-miquel.raynal@bootlin.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To solve this, remove the
lookup and create the directory on the first device found, and then
remove it when the module is unloaded.
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: Pratyush Yadav <pratyush@kernel.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20230208160230.2179905-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sort headers alphabetically - it helps locating duplicates, and makes it
easier to figure out where to insert new headers. Alphabetic order should
also prove that each header is self-contained, i.e. can be included without
prerequisites.
Link: https://lore.kernel.org/r/20230202144628.14443-1-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
At the moment, we print the JEDEC ID that is stored in our database. The
generic flash support won't have such an entry in our database. To find
out the JEDEC ID later we will have to cache it. There is also another
advantage: If the flash is found in the database, the ID could be
truncated because the ID of the entry is used which can be shorter. Some
flashes still holds valuable information in the bytes after the JEDEC ID
and come in handy during debugging of when coping with INFO6() entries.
These are not accessible for now.
Save a copy of the ID bytes after reading and display it via debugfs.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-4-michael@walle.cc
Address width was an unfortunate name, as it means the number of IO lines
used for the address, whereas in the code it is used as the number of
address bytes. s/addr_width/addr_nbytes throughout the entire SPI NOR
framework.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220725092505.446315-2-tudor.ambarus@microchip.com
The intention was to print the JEDEC ID in the following format:
nn nn nn
In this case format specifier has to be "%*ph". Fix it.
Fixes: 0257be79fc ("mtd: spi-nor: expose internal parameters via debugfs")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220512112027.3771734-1-michael@walle.cc
There is no way to gather all information to verify support for a new
flash chip. Also if you want to convert an existing flash chip to the
new SFDP parsing, there is not enough information to determine if the
flash will work like before. To ease this development, expose internal
parameters via the debugfs.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429102018.2361038-2-michael@walle.cc
