The mainline MTK ethernet driver suffers long time from rarly but
annoying tx queue timeouts. We think that this is caused by fixed
dma sizes hardcoded for all SoCs.
We suspect this problem arises from a low level of free TX DMADs,
the TX Ring alomost full.
The transmit timeout is caused by the Tx queue not waking up. The
Tx queue stops when the free counter is less than ring->thres, and
it will wake up once the free counter is greater than ring->thres.
If the CPU is too late to wake up the Tx queues, it may cause a
transmit timeout.
Therefore, we increased the TX and RX DMADs to improve this error
situation.
Use the dma-size implementation from SDK in a per SoC manner. In
difference to SDK we have no RSS feature yet, so all RX/TX sizes
should be raised from 512 to 2048 byte except fqdma on mt7988 to
avoid the tx timeout issue.
Fixes: 656e705243 ("net-next: mediatek: add support for MT7623 ethernet")
Suggested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ADMAv2.0 is plagued by RX hangs which can't easily detected and happen upon
receival of a corrupted Ethernet frame.
Use ADMAv1 instead which is also still present and usable, and doesn't
suffer from that problem.
Fixes: 197c9e9b17 ("net: ethernet: mtk_eth_soc: introduce support for mt7986 chipset")
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/57cef74bbd0c243366ad1ff4221e3f72f437ec80.1715164770.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Split tx and rx fields in mtk_soc_data struct. This is a preliminary
patch to roll back to ADMAv1 for MT7986 and MT7981 SoC in order to fix a
hw hang if the device receives a corrupted packet when using ADMAv2.0.
Fixes: 197c9e9b17 ("net: ethernet: mtk_eth_soc: introduce support for mt7986 chipset")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/70a799b1f060ec2f57883e88ccb420ac0fb0abb5.1715164770.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c945 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from the private struct by converting it
into a pointer. Then use the leverage the new alloc_netdev_dummy()
helper to allocate and initialize dummy devices.
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing bit MAC_MCR_FORCE_LINK which forces the link down too early
can result in MAC ending up in a broken/blocked state.
Fix this by handling this bit in the .mac_link_up and .mac_link_down
calls instead of in .mac_finish.
Fixes: b8fc9f3082 ("net: ethernet: mediatek: Add basic PHYLINK support")
Suggested-by: Mason-cw Chang <Mason-cw.Chang@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set DMA coherent mask to 32-bit which makes PPE offloading engine start
working on BPi-R4 which got 4 GiB of RAM.
Fixes: 2d75891ebc ("net: ethernet: mtk_eth_soc: support 36-bit DMA addressing on MT7988")
Suggested-by: Elad Yifee <eladwf@users.github.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/97e90925368b405f0974b9b15f1b7377c4a329ad.1706113251.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use more inclusive terms throughout the DSA subsystem by moving away
from "master" which is replaced by "conduit" and "slave" which is
replaced by "user". No functional changes.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231023181729.1191071-2-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While searching for possible refactor of napi_schedule_prep and
__napi_schedule it was notice that the mtk eth driver disable the
interrupt for rx and tx AFTER napi is scheduled.
While this is a very hard to repro case it might happen to have
situation where the interrupt is disabled and never enabled again as the
napi completes and the interrupt is enabled before.
This is caused by the fact that a napi driven by interrupt expect a
logic with:
1. interrupt received. napi prepared -> interrupt disabled -> napi
scheduled
2. napi triggered. ring cleared -> interrupt enabled -> wait for new
interrupt
To prevent this case, disable the interrupt BEFORE the napi is
scheduled.
Fixes: 656e705243 ("net-next: mediatek: add support for MT7623 ethernet")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20231002140805.568-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
xdp_do_flush_map() is deprecated and new code should use xdp_do_flush()
instead.
Replace xdp_do_flush_map() with xdp_do_flush().
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: Clark Wang <xiaoning.wang@nxp.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: David Arinzon <darinzon@amazon.com>
Cc: Edward Cree <ecree.xilinx@gmail.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: John Crispin <john@phrozen.org>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: Louis Peens <louis.peens@corigine.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Mark Lee <Mark-MC.Lee@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Noam Dagan <ndagan@amazon.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Saeed Bishara <saeedb@amazon.com>
Cc: Saeed Mahameed <saeedm@nvidia.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Shay Agroskin <shayagr@amazon.com>
Cc: Shenwei Wang <shenwei.wang@nxp.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Arthur Kiyanovski <akiyano@amazon.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230908143215.869913-2-bigeasy@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to MT7986 and MT7622, enable Wireless Ethernet Ditpatcher for
MT7988 in order to offload traffic forwarded from LAN/WLAN to WLAN/LAN
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Variable dma_addr in function mtk_poll_rx can be uninitialized on
some of the error paths. In practise this doesn't matter, even random
data present in uninitialized stack memory can safely be used in the
way it happens in the error path.
However, in order to make Smatch happy make sure the variable is
always initialized.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rule_locs is allocated in ethtool_get_rxnfc and the size is determined by
rule_cnt from user space. So rule_cnt needs to be check before using
rule_locs to avoid NULL pointer dereference.
Fixes: 7aab747e55 ("net: ethernet: mediatek: add ethtool functions to configure RX flows of HW LRO")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Systems having 4 GiB of RAM and more require DMA addressing beyond the
current 32-bit limit. Starting from MT7988 the hardware now supports
36-bit DMA addressing, let's use that new capability in the driver to
avoid running into swiotlb on systems with 4 GiB of RAM or more.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/95b919c98876c9e49761e44662e7c937479eecb8.1692721443.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MT7981, MT7986 and MT7988 come with in-SoC SRAM dedicated for Ethernet
DMA rings. Support using the SRAM without breaking existing device tree
bindings, ie. only new SoC starting from MT7988 will have the SRAM
declared as additional resource in device tree. For MT7981 and MT7986
an offset on top of the main I/O base is used.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/e45e0f230c63ad58869e8fe35b95a2fb8925b625.1692721443.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Split types and pure function declarations from page_pool.h
and add them in page_page/types.h, so that C sources can
include page_pool.h and headers should generally only include
page_pool/types.h as suggested by jakub.
Rename page_pool.h to page_pool/helpers.h to have both in
one place.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://lore.kernel.org/r/20230804180529.2483231-2-aleksander.lobakin@intel.com
[Jakub: change microsoft/mana, fix kdoc paths in Documentation]
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
NETSYS_V3 uses 64 bits for each counters while older SoCs are using
48/40 bits for each counter.
Support reading per-flow byte and package counters on NETSYS_V3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/37a0928fa8c1253b197884c68ce1f54239421ac5.1690946442.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230727014944.3972546-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce support for ethernet chip available in MT7988 SoC to
mtk_eth_soc driver. As a first step support only the first GMAC which
is hard-wired to the internal DSA switch having 4 built-in gigabit
Ethernet PHYs.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/25c8377095b95d186872eeda7aa055da83e8f0ca.1690246605.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce version field in mtk_soc_data data structure in order to
make mtk_eth driver easier to maintain for chipset configuration
codebase. Get rid of MTK_NETSYS_V2 bit in chip capabilities.
This is a preliminary patch to introduce support for MT7988 SoC.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/e52fae302ca135436e5cdd26d38d87be2da63055.1690246066.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the .mac_pcs_get_state function, since as far as I can tell is
never called - no DT appears to specify an in-band-status management
nor SFP support for this driver.
Removal of this, along with the previous patch to remove the incorrect
clocking configuration, means that the driver becomes non-legacy, so
we can remove the "legacy_pre_march2020" status from this driver.
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
MT7623 GMAC0 attempts to configure the system clocking according to the
required speed in the .mac_config callback for non-SGMII, non-baseX and
non-TRGMII modes.
state->speed setting has never been reliable in the .mac_config
callback - there are cases where this is not the link speed,
particularly via ethtool paths, so this has always been unreliable (as
detailed in phylink's documentation.)
There is the additional issue that mtk_gmac0_rgmii_adjust() will only
be called if state->interface changes, which means it only configures
the system clocking on the very first .mac_config call, which will be
made when the network device is first brought up before any link is
established.
Essentially, this code is incredibly buggy, and probably never worked.
Moreover, checking the in-kernel DT files, it seems no platform makes
use of this code path.
Therefore, let's remove it, and disable interface modes for port 0 that
are not SGMII, 1000base-X, 2500base-X or TRGMII on the MT7623.
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce MTK_FOE_ENTRY_V{1,2}_SIZE macros in order to make more
explicit foe_entry size for different chipset revisions.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the call to of_get_ethdev_address to mtk_add_mac which is part of
the probe function and can hence itself return -EPROBE_DEFER should
of_get_ethdev_address return -EPROBE_DEFER. This allows us to entirely
get rid of the mtk_init function.
The problem of of_get_ethdev_address returning -EPROBE_DEFER surfaced
in situations in which the NVMEM provider holding the MAC address has
not yet be loaded at the time mtk_eth_soc is initially probed. In this
case probing of mtk_eth_soc should be deferred instead of falling back
to use a random MAC address, so once the NVMEM provider becomes
available probing can be repeated.
Fixes: 656e705243 ("net-next: mediatek: add support for MT7623 ethernet")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit c6d96df9fa ("net: ethernet: mtk_eth_soc: drop generic vlan rx
offload, only use DSA untagging") makes VLAN RX offloading to be only used
on the SoCs without the MTK_NETSYS_V2 ability (which are not just MT7621
and MT7622). The commit disables the proper handling of special tagged
(DSA) frames, added with commit 87e3df4961 ("net-next: ethernet:
mediatek: add CDM able to recognize the tag for DSA"), for non
MTK_NETSYS_V2 SoCs when it finds a MAC that does not use DSA. So if the
other MAC uses DSA, the CDMQ component transmits DSA tagged frames to the
CPU improperly. This issue can be observed on frames with TCP, for example,
a TCP speed test using iperf3 won't work.
The commit disables the proper handling of special tagged (DSA) frames
because it assumes that these SoCs don't use more than one MAC, which is
wrong. Although I made Frank address this false assumption on the patch log
when they sent the patch on behalf of Felix, the code still made changes
with this assumption.
Therefore, the proper handling of special tagged (DSA) frames must be kept
enabled in all circumstances as it doesn't affect non DSA tagged frames.
Hardware DSA untagging, introduced with the commit 2d7605a729 ("net:
ethernet: mtk_eth_soc: enable hardware DSA untagging"), and VLAN RX
offloading are operations on the two CDM components of the frame engine,
CDMP and CDMQ, which connect to Packet DMA (PDMA) and QoS DMA (QDMA) and
are between the MACs and the CPU. These operations apply to all MACs of the
SoC so if one MAC uses DSA and the other doesn't, the hardware DSA
untagging operation will cause the CDMP component to transmit non DSA
tagged frames to the CPU improperly.
Since the VLAN RX offloading feature configuration was dropped, VLAN RX
offloading can only be used along with hardware DSA untagging. So, for the
case above, we need to disable both features and leave it to the CPU,
therefore software, to untag the DSA and VLAN tags.
So the correct way to handle this is:
For all SoCs:
Enable the proper handling of special tagged (DSA) frames
(MTK_CDMQ_IG_CTRL).
For non MTK_NETSYS_V2 SoCs:
Enable hardware DSA untagging (MTK_CDMP_IG_CTRL).
Enable VLAN RX offloading (MTK_CDMP_EG_CTRL).
When a non MTK_NETSYS_V2 SoC MAC does not use DSA:
Disable hardware DSA untagging (MTK_CDMP_IG_CTRL).
Disable VLAN RX offloading (MTK_CDMP_EG_CTRL).
Fixes: c6d96df9fa ("net: ethernet: mtk_eth_soc: drop generic vlan rx offload, only use DSA untagging")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Through testing I found out that hardware vlan rx offload support seems to
have some hardware issues. At least when using multiple MACs and when
receiving tagged packets on the secondary MAC, the hardware can sometimes
start to emit wrong tags on the first MAC as well.
In order to avoid such issues, drop the feature configuration and use
the offload feature only for DSA hardware untagging on MT7621/MT7622
devices where this feature works properly.
Fixes: 08666cbb7d ("net: ethernet: mtk_eth_soc: add support for configuring vlan rx offload")
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230426172153.8352-1-linux@fw-web.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Based on further tests, it seems that the QDMA shaper is not able to
perform shaping close to the MAC link rate without throughput loss.
This cannot be compensated by increasing the shaping rate, so it seems
to be an internal limit.
Fix the remaining throughput regression by detecting that condition and
limiting shaping to ports with lower link speed.
This patch intentionally ignores link speed gain from TRGMII, because
even on such links, shaping to 1000 Mbit/s incurs some throughput
degradation.
Fixes: f63959c7ee ("net: ethernet: mtk_eth_soc: implement multi-queue support for per-port queues")
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Check for skb metadata in order to detect the case where the DSA header
is not present.
Fixes: 2d7605a729 ("net: ethernet: mtk_eth_soc: enable hardware DSA untagging")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230330120840.52079-2-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using the QDMA tx scheduler to throttle tx to line speed works fine for
switch ports, but apparently caused a regression on non-switch ports.
Based on a number of tests, it seems that this throttling can be safely
dropped without re-introducing the issues on switch ports that the
tx scheduling changes resolved.
Link: https://lore.kernel.org/netdev/trinity-92c3826f-c2c8-40af-8339-bc6d0d3ffea4-1678213958520@3c-app-gmx-bs16/
Fixes: f63959c7ee ("net: ethernet: mtk_eth_soc: implement multi-queue support for per-port queues")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Reported-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230324140404.95745-1-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that we got a PCS driver, use it and remove the now redundant
PCS code and it's header macros from the Ethernet driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PPE units found in MT7622 and newer support packet and byte
accounting of hw-offloaded flows. Add support for reading those counters
as found in MediaTek's SDK[1].
[1]: bc6a6a375c
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Set MDIO bus clock frequency and allow setting a custom maximum
frequency from device tree.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MediaTek MT7981 SoC comes with two 1G/2.5G SGMII ports, just like
MT7986.
In addition MT7981 is equipped with a built-in 1000Base-T PHY which can
be used with GMAC1.
As many MT7981 boards make use of inverting SGMII signal polarity, add
new device-tree attribute 'mediatek,pn_swap' to support them.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the conversion of mtk_eth_soc to phylink's supported_interfaces
bitmap, these two modes have not been selectable. No one has raised
this as an issue. Checking the in-kernel DT files, none of them use
either of these modes with this hardware.
Daniel Golle concurs:
A quick grep through the device trees of the more than 650 ramips and
mediatek boards we support in OpenWrt has revealed that *none* of them
uses either reduced-MII or reverse-MII PHY modes. I could imaging that
some more specialized ramips boards may use the RMII 100M PHY mode to
connect with exotic PHYs for industrial or automotive applications
(think: for 100BASE-T1 PHY connected via RMII). I have never seen or
touched such boards, but there are hints that they do exist.
For reverse-MII there are cases in which the Ralink SoC (Rt305x, for
example) is used in iNIC mode, ie. connected as a PHY to another SoC,
and running only a minimal firmware rather than running Linux. Due to
the lack of external DRAM for the Ralink SoC on this kind of boards,
the Ralink SoC there will anyway never be able to boot Linux.
I've seen this e.g. in multimedia devices like early WiFi-connected
not-yet-so-smart TVs.
Consequently, the conclusion is that no one uses these modes with this
hardware, so we might as well drop support for them.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
mtk_mac_config() checks that the interface mode is permitted for the
capabilities, but we already do these checks in mtk_add_mac() when
initialising phylink's supported_interfaces bitmap. Remove the
unnecessary tests.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If TRGMII mode is not permitted when using DDR2 mode, we should handle
that when setting up phylink's ->supported_interfaces so phylink knows
that this is not supported by the hardware. Move this check to
mtk_add_mac().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Get rid of the multiple tenary operators in mtk_gmac0_rgmii_adjust()
replacing them with a single if(), thus making the code easier to read.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix data corruption issue with SerDes connected PHYs operating at 1.25
Gbps speed where we could previously observe about 30% packet loss while
the bad packet counter was increasing.
As almost all boards with MediaTek MT7622 or MT7986 use either the MT7531
switch IC operating at 3.125Gbps SerDes rate or single-port PHYs using
rate-adaptation to 2500Base-X mode, this issue only got exposed now when
we started trying to use SFP modules operating with 1.25 Gbps with the
BananaPi R3 board.
The fix is to set bit 12 which disables the RX FIFO clear function when
setting up MAC MCR, MediaTek SDK did the same change stating:
"If without this patch, kernel might receive invalid packets that are
corrupted by GMAC."[1]
[1]: d8a2975939
Fixes: 42c03844e9 ("net-next: mediatek: add support for MediaTek MT7622 SoC")
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/138da2735f92c8b6f8578ec2e5a794ee515b665f.1677937317.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
