Replace hwtstamp_source which is only used by the kernel_hwtstamp_config
structure by the more widely use timestamp_layer structure. This is done
to prepare the support of selectable timestamping source.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently all RX frames are timestamped which results in a performance
penalty when timestamping is not needed. The default is now being
changed to not timestamp any Rx frames (HWTSTAMP_FILTER_NONE), but
support has been added to allow changing the desired RX timestamping
mode (HWTSTAMP_FILTER_ALL - which was the previous setting and
HWTSTAMP_FILTER_PTP_V2_EVENT are now supported) using
SIOCSHWTSTAMP. All settings were tested using the hwstamp_ctl application.
It is also noted that ptp4l, when started, preconfigures the device to
timestamp using HWTSTAMP_FILTER_PTP_V2_EVENT, so this driver continues
to work properly "out of the box".
Test setup: x64 PC with LAN7430 ---> x64 PC as partner
iperf3 with - Timestamp all incoming packets:
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-5.05 sec 517 MBytes 859 Mbits/sec 0 sender
[ 5] 0.00-5.00 sec 515 MBytes 864 Mbits/sec receiver
iperf Done.
iperf3 with - Timestamp only PTP packets:
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-5.04 sec 563 MBytes 937 Mbits/sec 0 sender
[ 5] 0.00-5.00 sec 561 MBytes 941 Mbits/sec receiver
Signed-off-by: Vishvambar Panth S <vishvambarpanth.s@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231020185801.25649-1-vishvambarpanth.s@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
'err' is useless after break, remove this to save space and
be more clear.
Signed-off-by: Su Hui <suhui@nfschina.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vcap_decode_rule() never returns NULL. There is no need to check
for that. This code assumes that if it did return NULL we should
end abruptly and return success. It is confusing. Fix the check to
just be if (IS_ERR()) instead of if (IS_ERR_OR_NULL()).
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/r/202309070831.hTvj9ekP-lkp@intel.com/
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://lore.kernel.org/r/b88eba86-9488-4749-a896-7c7050132e7b@moroto.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert these drivers from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When operating in fixed phy mode and if there is repeated open/close
phy test cases, everytime the fixed phy is registered as a new phy
which leads to overrun after 32 iterations. It is solved by adding
fixed_phy_unregister() in the phy_close path.
In phy_close path, netdev->phydev cannot be used directly in
fixed_phy_unregister() due to two reasons,
- netdev->phydev is set to NULL in phy_disconnect()
- fixed_phy_unregister() can be called only after phy_disconnect()
So saving the netdev->phydev in local variable 'phydev' and
passing it to phy_disconnect().
Signed-off-by: Pavithra Sathyanarayanan <Pavithra.Sathyanarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 264a9c5c9d ("net: sparx5: Remove unused GLAG handling in PGID")
removed sparx5_pgid_alloc_glag() but not its declaration.
Commit 27d293ccee ("net: microchip: sparx5: Add support for rule count by cookie")
removed vcap_rule_iter() but not its declaration.
Commit 8beef08f46 ("net: microchip: sparx5: Adding initial VCAP API support")
declared but never implemented vcap_api_set_client().
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230821135556.43224-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fixed_phy_register() returns -EPROBE_DEFER, -EINVAL and -EBUSY,
etc, in addition to -EIO. The Best practice is to return these
error codes with PTR_ERR().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Simon Horman suggests, update vcap_get_rule() to always
return an ERR_PTR() and update the error detection conditions to
use IS_ERR(), so use IS_ERR() to check the return value.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Suggested-by: Simon Horman <horms@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Simon Horman suggests, update vcap_get_rule() to always
return an ERR_PTR() and update the error detection conditions to
use IS_ERR(), so use IS_ERR() to fix the return value issue.
Fixes: 72df3489fb ("net: lan966x: Add ptp trap rules")
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Suggested-by: Simon Horman <horms@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Simon Horman suggests, update vcap_get_rule() to always
return an ERR_PTR() and update the error detection conditions to
use IS_ERR(), which would be more cleaner in this case.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Suggested-by: Simon Horman <horms@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split types and pure function declarations from page_pool.h
and add them in page_page/types.h, so that C sources can
include page_pool.h and headers should generally only include
page_pool/types.h as suggested by jakub.
Rename page_pool.h to page_pool/helpers.h to have both in
one place.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://lore.kernel.org/r/20230804180529.2483231-2-aleksander.lobakin@intel.com
[Jakub: change microsoft/mana, fix kdoc paths in Documentation]
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since platform_get_irq_byname() never returned zero, so it need not to
check whether it returned zero, it returned -EINVAL or -ENXIO when
failed, so we replace the return error code with the result it returned.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a warning reported by coccinelle:
./drivers/net/ethernet/microchip/vcap/vcap_api.c:2399:9-16: WARNING:
ERR_CAST can be used with ri
Use ERR_CAST instead of ERR_PTR + PTR_ERR to simplify the
conversion process.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRdM/uy1Ege0+EN1fNar9k/UBDW4wUCZMvevwAKCRBar9k/UBDW
42Z0AP90hLZ9OmoghYAlALHLl8zqXuHCV8OeFXR5auqG+kkcCwEAx6h99vnh4zgP
Tngj6Yid60o39/IZXXblhV37HfSiyQ8=
=/kVE
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Martin KaFai Lau says:
====================
pull-request: bpf-next 2023-08-03
We've added 54 non-merge commits during the last 10 day(s) which contain
a total of 84 files changed, 4026 insertions(+), 562 deletions(-).
The main changes are:
1) Add SO_REUSEPORT support for TC bpf_sk_assign from Lorenz Bauer,
Daniel Borkmann
2) Support new insns from cpu v4 from Yonghong Song
3) Non-atomically allocate freelist during prefill from YiFei Zhu
4) Support defragmenting IPv(4|6) packets in BPF from Daniel Xu
5) Add tracepoint to xdp attaching failure from Leon Hwang
6) struct netdev_rx_queue and xdp.h reshuffling to reduce
rebuild time from Jakub Kicinski
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (54 commits)
net: invert the netdevice.h vs xdp.h dependency
net: move struct netdev_rx_queue out of netdevice.h
eth: add missing xdp.h includes in drivers
selftests/bpf: Add testcase for xdp attaching failure tracepoint
bpf, xdp: Add tracepoint to xdp attaching failure
selftests/bpf: fix static assert compilation issue for test_cls_*.c
bpf: fix bpf_probe_read_kernel prototype mismatch
riscv, bpf: Adapt bpf trampoline to optimized riscv ftrace framework
libbpf: fix typos in Makefile
tracing: bpf: use struct trace_entry in struct syscall_tp_t
bpf, devmap: Remove unused dtab field from bpf_dtab_netdev
bpf, cpumap: Remove unused cmap field from bpf_cpu_map_entry
netfilter: bpf: Only define get_proto_defrag_hook() if necessary
bpf: Fix an array-index-out-of-bounds issue in disasm.c
net: remove duplicate INDIRECT_CALLABLE_DECLARE of udp[6]_ehashfn
docs/bpf: Fix malformed documentation
bpf: selftests: Add defrag selftests
bpf: selftests: Support custom type and proto for client sockets
bpf: selftests: Support not connecting client socket
netfilter: bpf: Support BPF_F_NETFILTER_IP_DEFRAG in netfilter link
...
====================
Link: https://lore.kernel.org/r/20230803174845.825419-1-martin.lau@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Handful of drivers currently expect to get xdp.h by virtue
of including netdevice.h. This will soon no longer be the case
so add explicit includes.
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230803010230.1755386-2-kuba@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
It is desirable that the new .ndo_hwtstamp_set() API gives more
uniformity, less overhead and future flexibility w.r.t. the PHY
timestamping behavior.
Currently there are some drivers which allow PHY timestamping through
the procedure mentioned in Documentation/networking/timestamping.rst.
They don't do anything locally if phy_has_hwtstamp() is set, except for
lan966x which installs PTP packet traps.
Centralize that behavior in a new dev_set_hwtstamp_phylib() code
function, which calls either phy_mii_ioctl() for the phylib PHY,
or .ndo_hwtstamp_set() of the netdev, based on a single policy
(currently simplistic: phy_has_hwtstamp()).
Any driver converted to .ndo_hwtstamp_set() will automatically opt into
the centralized phylib timestamping policy. Unconverted drivers still
get to choose whether they let the PHY handle timestamping or not.
Netdev drivers with integrated PHY drivers that don't use phylib
presumably don't set dev->phydev, and those will always see
HWTSTAMP_SOURCE_NETDEV requests even when converted. The timestamping
policy will remain 100% up to them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20230801142824.1772134-13-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hardware timestamping through ndo_eth_ioctl() is going away.
Convert the lan966x driver to the new API before that can be removed.
After removing the timestamping logic from lan966x_port_ioctl(), the
rest is equivalent to phy_do_ioctl().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20230801142824.1772134-10-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hardware timestamping through ndo_eth_ioctl() is going away.
Convert the sparx5 driver to the new API before that can be removed.
After removing the timestamping logic from sparx5_port_ioctl(), the rest
is equivalent to phy_do_ioctl().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Link: https://lore.kernel.org/r/20230801142824.1772134-9-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As 32bits of dissector->used_keys are exhausted,
increase the size to 64bits.
This is base change for ESP/AH flow dissector patch.
Please find patch and discussions at
https://lore.kernel.org/netdev/ZMDNjD46BvZ5zp5I@corigine.com/T/#t
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Tested-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230727014944.3972546-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The blamed commit introduces usage of fixed_phy_register() but
not a corresponding dependency on FIXED_PHY.
This can result in a build failure.
s390-linux-ld: drivers/net/ethernet/microchip/lan743x_main.o: in function `lan743x_phy_open':
drivers/net/ethernet/microchip/lan743x_main.c:1514: undefined reference to `fixed_phy_register'
Fixes: 624864fbff ("net: lan743x: add fixed phy support for LAN7431 device")
Cc: stable@vger.kernel.org
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/netdev/725bf1c5-b252-7d19-7582-a6809716c7d6@infradead.org/
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_set_rx_mode() grabs a spin_lock, and the lan743x implementation
proceeds subsequently to go to sleep using readx_poll_timeout().
Introduce a helper wrapping the readx_poll_timeout_atomic() function
and use it to replace the calls to readx_polL_timeout().
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Cc: stable@vger.kernel.org
Cc: Bryan Whitehead <bryan.whitehead@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230627035000.1295254-1-moritzf@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Update Sparx5's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8EZ-00EaGF-6F@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update lan966x's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8E9-00EaFl-GN@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The gotos for cleanup aren't required, the function
might as well just return the actual error code.
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inspired from struct flow_cls_offload :: cmd, in order for taprio to be
able to report statistics (which is future work), it seems that we need
to drill one step further with the ndo_setup_tc(TC_SETUP_QDISC_TAPRIO)
multiplexing, and pass the command as part of the common portion of the
muxed structure.
Since we already have an "enable" variable in tc_taprio_qopt_offload,
refactor all drivers to check for "cmd" instead of "enable", and reject
every other command except "replace" and "destroy" - to be future proof.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> # for lan966x
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was noticing that after a while when unloading/loading the driver and
sending traffic through the switch, it would stop working. It would stop
forwarding any traffic and the only way to get out of this was to do a
power cycle of the board. The root cause seems to be that the switch
core is initialized twice. Apparently initializing twice the switch core
disturbs the pointers in the queue systems in the HW, so after a while
it would stop sending the traffic.
Unfortunetly, it is not possible to use a reset of the switch here,
because the reset line is connected to multiple devices like MDIO,
SGPIO, FAN, etc. So then all the devices will get reseted when the
network driver will be loaded.
So the fix is to check if the core is initialized already and if that is
the case don't initialize it again.
Fixes: db8bcaad53 ("net: lan966x: add the basic lan966x driver")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230522120038.3749026-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for DSCP rewrite in lan966x driver. On egress DSCP is
rewritten from either classified DSCP, or frame DSCP. Classified DSCP is
determined by the Analyzer Classifier on ingress, and is mapped from
classified QoS class and DP level. Classification of DSCP is by default
enabled for all ports.
It is required that DSCP is trusted for the egress port *and* rewrite
table is not empty, in order to rewrite DSCP based on classified DSCP,
otherwise DSCP is always rewritten from frame DSCP.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for rewrite of PCP and DEI value, based on QoS and DP level.
The DCB rewrite table is queried for mappings between priority and
PCP/DEI. The classified DP level is then encoded in the DEI bit, if a
mapping for DEI exists.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for offloading default prio.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for offloading dscp app entries. The dscp values are global
for all lan966x ports.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Make use of set/getapptrust() to implement per-selector trust
and trust order.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for offloading pcp app entries. Lan966x has 8 priority
queues per port and for each priority it also has a drop precedence.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add the registers that are needed to configure the PCP, DEI and DSCP
of the switch both at ingress and also at egress.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Remove the extra semicolon at end. Issue identified using
semicolon.cocci Coccinelle semantic patch.
drivers/net/ethernet/microchip/vcap/vcap_api.c:1124:3-4: Unneeded semicolon
drivers/net/ethernet/microchip/vcap/vcap_api.c:1165:3-4: Unneeded semicolon
drivers/net/ethernet/microchip/vcap/vcap_api.c:1239:3-4: Unneeded semicolon
drivers/net/ethernet/microchip/vcap/vcap_api.c:1287:3-4: Unneeded semicolon
Signed-off-by: Anup Sharma <anupnewsmail@gmail.com>
Changes:
V1 -> V2: Target tree included in the subject line.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Microchip ENC28J60 SPI Ethernet driver schedules a work item from
the interrupt handler because accesses to the SPI bus may sleep.
On PREEMPT_RT (which forces interrupt handling into threads) this
old-fashioned approach unnecessarily increases latency because an
interrupt results in first waking the interrupt thread, then scheduling
the work item. So, a double indirection to handle an interrupt.
Avoid by converting the driver to modern threaded interrupt handling.
Signed-off-by: Philipp Rosenberger <p.rosenberger@kunbus.com>
Signed-off-by: Zhi Han <hanzhi09@gmail.com>
[lukas: rewrite commit message, linewrap request_threaded_irq() call]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Link: https://lore.kernel.org/r/342380d989ce26bc49f0e5d45fbb0416a5f7809f.1683606193.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable the TC command to use the lan966x ES0 VCAP. Currently support
only one action which is vlan pop, other will be added later.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
