Allow jumbo frames by changing maximum MTU size and number of RX queues.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If this hardware receives a jumbo frame like 2KiB or more, it will be
split into multiple queues. In the near future, to support this,
add handling specific descriptor types F{START,MID,END}. However, such
jumbo frames will not happen yet because the maximum MTU size is still
default for now.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support jumbo frames, set GWMDNC register with acceptable maximum
values for TX and RX.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver would like to transmit a jumbo frame like 2KiB or more,
it should be split into multiple queues. In the near future, to support
this, add unmap_addrs array to unmap dma mapping address instead of dma
address in each TX descriptor because the descriptors may not have
the top dma address.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If this hardware receives a jumbo frame like 2KiB or more, it will be
split into multiple queues. In the near future, to support this, use
build_skb() instead of netdev_alloc_skb_ip_align().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Array index should not be negative, so use unsigned int for
descriptors related array index.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Array index should not be negative, so modify the condition of
rswitch_for_each_enabled_port_continue_reverse() macro, and then
use unsigned int instead.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix the MPIC.PSMCS value following the programming example in the
section 6.4.2 Management Data Clock (MDC) Setting, Ethernet MAC IP,
S4 Hardware User Manual Rev.1.00.
The value is calculated by
MPIC.PSMCS = clk[MHz] / (MDC frequency[MHz] * 2) - 1
with the input clock frequency from clk_get_rate() and MDC frequency
of 2.5MHz. Otherwise, this driver cannot communicate PHYs on the R-Car
S4 Starter Kit board.
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Reported-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230926123054.3976752-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add spin lock protection for irq {un}mask registers' control.
After napi_complete_done() and this protection were applied,
a lot of redundant interrupts no longer occur.
For example: when "iperf3 -c <ipaddr> -R" on R-Car S4-8 Spider
Before the patches are applied: about 800,000 times happened
After the patches were applied: about 100,000 times happened
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The latest SoC version can support runtime speed change. So,
add detect SoC version by using soc_device_match() and then
reconfigure the hardware of this and SerDes if needed.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230807003231.1552062-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since this driver used the "global rate limiter" feature of GWCA,
the TX performance of each port was reduced when multiple ports
transmitted frames simultaneously. To improve performance, remove
the use of the "global rate limiter" feature and use "hardware pause"
features of the following:
- "per priority pause" of GWCA
- "global pause" of COMA
Note that these features are not related to the ethernet PAUSE frame.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the GWCA has the TX timestamp feature, this driver
should not disable it if one of ports is opened. So, fix it.
Reported-by: Phong Hoang <phong.hoang.wz@renesas.com>
Fixes: 33f5d733b5 ("net: renesas: rswitch: Improve TX timestamp accuracy")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous code, TX timestamp accuracy was bad because the irq
handler got the timestamp from the timestamp register at that time.
This hardware has "Timestamp capture" feature which can store
each TX timestamp into the timestamp descriptors. To improve
TX timestamp accuracy, implement timestamp descriptors' handling.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the previous code, the gptp flag was completely related to
the !dir_tx in struct rswitch_gwca_queue because
rswitch_gwca_queue_alloc() was called below:
< In rswitch_txdmac_alloc() >
err = rswitch_gwca_queue_alloc(ndev, priv, rdev->tx_queue, true, false,
TX_RING_SIZE);
So, dir_tx = true, and gptp = false.
< In rswitch_rxdmac_alloc() >
err = rswitch_gwca_queue_alloc(ndev, priv, rdev->rx_queue, false, true,
RX_RING_SIZE);
So, dir_tx = false, and gptp = true.
In the future, a new queue handling for timestamp will be implemented
and this gptp flag is confusable. So, remove the gptp flag.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To improve readability, move linkfix related variables to
struct rswitch_gwca. Also, rename function names "desc" with "linkfix".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To add a new ring which is really related to timestamp (ts_ring)
in the future, rename the following members to improve readability:
ring --> tx_ring
ts_ring --> rx_ring
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Intended to set phy_device->host_interfaces by phylink in the future.
But there is difficult to implement phylink properly, especially
supporting the in-band mode on this driver because extra initialization
is needed after linked the ethernet PHY up. So, convert to phy_device
from phylink.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify struct phy *serdes handling by keeping the valiable in
the struct rswitch_device.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If one of ports in the ethernet-ports was disabled, this driver
failed to probe all ports. So, fix it.
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230120001959.1059850-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Coverity reported that the error path in rswitch_gwca_queue_alloc_skb()
has an issue to cause endless loop. So, fix the issue by changing
variables' types from u32 to int. After changed the types,
rswitch_tx_free() should use rswitch_get_num_cur_queues() to
calculate number of current queues.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 1527147 ("Control flow issues")
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20221107081021.2955122-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add R-Car Gen4 gPTP support into the rswitch driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial support for Renesas "Ethernet Switch" device of R-Car S4-8.
The hardware has features about forwarding for an ethernet switch
device. But, for now, it acts as ethernet controllers so that any
forwarding offload features are not supported. So, any switchdev
header files and DSA framework are not used.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
