Broadcom PHYs have two LEDs selector registers which allow us to control
the LED assignment, including how to turn them on/off.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to have our interrupt descriptor fully setup and in particular
the action, ensure that we register a full fledged interrupt handler.
This also allow us to set the interrupt polarity and flow through the
same call.
This is specifically necessary for kernel/irq/pm.c::suspend_device_irq
to set the interrupt descriptor to the IRQD_WAKEUP_ARMED state and
enable the interrupt for wake-up since it was still in a disabled state.
Without an interrupt descriptor we would have ran into cases where the
wake-up interrupt is not capable of waking up the system, specifically
if we resumed the system ACPI S5 using the Ethernet PHY. In that case
the Ethernet PHY interrupt would be pending by the time the kernel
booted, which it would acknowledge but then we could never use it as
a wake-up source again.
Fixes: 8baddaa9d4 ("net: phy: broadcom: Add support for Wake-on-LAN")
Suggested-by: Doug Berger <doug.berger@broadcom.com>
Debugged-by: Doug Berger <doug.berger@broadcom.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for WAKE_UCAST, WAKE_MCAST, WAKE_BCAST, WAKE_MAGIC and
WAKE_MAGICSECURE. This is only supported with the BCM54210E and
compatible Ethernet PHYs. Using the in-band interrupt or an out of band
GPIO interrupts are supported.
Broadcom PHYs will generate a Wake-on-LAN level low interrupt on LED4 as
soon as one of the supported patterns is being matched. That includes
generating such an interrupt even if the PHY is operated during normal
modes. If WAKE_UCAST is selected, this could lead to the LED4 interrupt
firing up for every packet being received which is absolutely
undesirable from a performance point of view.
Because the Wake-on-LAN configuration can be set long before the system
is actually put to sleep, we cannot have an interrupt service routine to
clear on read the interrupt status register and ensure that new packet
matches will be detected.
It is desirable to enable the Wake-on-LAN interrupt as late as possible
during the system suspend process such that we limit the number of
interrupts to be handled by the system, but also conversely feed into
the Linux's system suspend way of dealing with interrupts in and around
the points of no return.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the driver works in the "legacy" addressing mode, we need to write
to the expansion register (0x17) with bits 11:8 set to 0xf to properly
select the expansion register passed as argument.
Fixes: f68d08c437 ("net: phy: bcm7xxx: Add EPHY entry for 72165")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230508231749.1681169-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add 'struct bcm_ptp_private' to bcm54xx_phy_priv which points to
an optional PTP structure attached to the PHY. This is allocated
on probe if PHY PTP support is configured, and if the driver supports
PTP for the specified PHY.
Add the bcm_ptp_probe(), bcm_ptp_config_init() and bcn_ptp_stop()
API functions to the bcm-phy library.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most modern broadcom PHYs support ECD (enhanced cable diagnostics). Add
support for it in the bcm-phy-lib so they can easily be used in the PHY
driver.
There are two access methods for ECD: legacy by expansion registers and
via the new RDB registers which are exclusive. Provide functions in two
variants where the PHY driver can choose from. To keep things simple for
now, we just switch the register access to expansion registers in the
RDB variant for now. On the flipside, we have to keep a bus lock to
prevent any other non-legacy access on the PHY.
The results of the intra-pair tests are inconclusive (at least for the
BCM54140). Most of the times half the length is reported but sometimes
the length is correct.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the convenience function to do a read-modify-write. This has the
additional benefit of saving one write to the selection register.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper to read and write expansion registers without taking the mdio
lock.
Please note, that this changes the semantics of the read and write.
Before there was no lock between selecting the expansion register and
the actual read/write. This may lead to access failures if there are
parallel accesses. Instead take the bus lock during the whole access
cycle.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDB (Register Data Base) registers are used on newer Broadcom PHYs. Add
helper to read, write and modify these registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM7XX PHY family requires special configuration to pass jumbo
frames. Do that during initial PHY setup.
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style in
header files related to PHY Layer for Ethernet drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used). This patch also gives an explicit
block comment to the SPDX License Identifier.
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Omega PHY entry was added to bcm7xxx.c out of convenience and this
breaks the one driver per product line paradigm that was applied up
until now. Since the AFE initialization is shared between Omega and
BCM7xxx move the relevant functions to bcm-phy-lib.[ch]. No functional
changes introduced.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On newer PHYs, we need to select the expansion register to write with
setting bits [11:8] to 0xf. This was done correctly by bcm7xxx.c prior
to being migrated to generic code under bcm-phy-lib.c which
unfortunately used the older implementation from the BCM54xx days.
Fix this by creating an inline stub: bcm_write_exp_sel() which adds the
correct value (MII_BCM54XX_EXP_SEL_ER) and update both the Cygnus PHY
and BCM7xxx PHY drivers which require setting these bits.
broadcom.c is unchanged because some PHYs even use a different selector
method, so let them specify it directly (e.g: SerDes secondary selector).
Fixes: a1cba5613e ("net: phy: Add Broadcom phy library for common interfaces")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom PHYs expose a number of PHY error counters: receive errors,
false carrier sense, SerDes BER count, local and remote receive errors.
Add support code to allow retrieving these error counters. Since the
Broadcom PHY library code is used by several drivers, make it possible
for them to specify the storage for the software copy of the statistics.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding support for Wirespeed/downshift, we need to
change bcm_phy_eee_enable() to allow enabling or disabling EEE, so make
the function take an extra enable/disable boolean parameter and rename
it to illustrate it sets EEE, not necessarily just enables it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom's Wirespeed feature allows us to configure how auto-negotiation
should behave with fewer working pairs of wires on a cable. Add support
code for retrieving and setting such downshift counters using the
recently added ethtool downshift tunables.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to need these functions to implement support for Broadcom
Wirespeed, aka downshift.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Broadcom phy library to consolidate common
interfaces shared by Broadcom phy's.
Moved the common interfaces to the 'bcm-phy-lib.c' and updated
the Broadcom PHY drivers to use the new APIs.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
