There are a few PHY drivers that can handle SFP modules through their
sfp_upstream_ops. Introduce Phylib helpers to keep track of connected
SFP PHYs in a netdevice's namespace, by adding the SFP PHY to the
upstream PHY's netdev's namespace.
By doing so, these SFP PHYs can be enumerated and exposed to users,
which will be able to use their capabilities.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stmmac controllers connected to an at803x PHY cannot resume properly after
suspend when WoL is enabled. This happens because the MAC requires an RX
clock generated by the PHY to initialize its hardware properly. But the RX
clock is cut when the PHY suspends and isn't brought up until the MAC
driver resumes the phylink.
Prevent the at803x PHY driver from going into suspend if the attached MAC
driver always requires an RX clock signal.
Reported-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/all/20230202081559.3553637-1-xiaoning.wang@nxp.com/
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
[rgantois: commit log]
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240326-rxc_bugfix-v6-6-24a74e5c761f@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On reworking and splitting the at803x driver, in splitting function of
at803x PHYs it was added a NULL dereference bug where priv is referenced
before it's actually allocated and then is tried to write to for the
is_1000basex and is_fiber variables in the case of at8031, writing on
the wrong address.
Fix this by correctly setting priv local variable only after
at803x_probe is called and actually allocates priv in the phydev struct.
Reported-by: William Wortel <wwortel@dorpstraat.com>
Cc: <stable@vger.kernel.org>
Fixes: 25d2ba9400 ("net: phy: at803x: move specific at8031 probe mode check to dedicated probe")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240325190621.2665-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kernel bot has discovered that if CONFIG_GPIOLIB is not set compilation
will fail.
Upon investigation the issue is that qca807x_gpio() is guarded by a
preprocessor check but then it is called under
if (IS_ENABLED(CONFIG_GPIOLIB)) in the probe call so the compiler will
error out since qca807x_gpio() has not been declared if CONFIG_GPIOLIB has
not been set.
Fixes: d1cb613efb ("net: phy: qcom: add support for QCA807x PHY Family")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202403031332.IGAbZzwq-lkp@intel.com/
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Link: https://lore.kernel.org/r/20240305142113.795005-1-robimarko@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently QCA808x driver does not fill the possible_interfaces.
2.5G QCA808x support SGMII and 2500Base-X while 1G model only supports
SGMII, so fill the possible_interfaces accordingly.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 versions of QCA808x, one 2.5G capable and one 1G capable.
Currently, this matter only in the .get_features call however, it will
be required for filling supported interface modes so lets add a helper
that can be reused.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we are checking whether the PHY package mode matches the
individual PHY interface modes at PHY package probe time, but at that time
we only know the PHY package mode and not the individual PHY interface
modes as of_get_phy_mode() that populates it will only get called once the
netdev to which PHY-s are attached to is being probed and thus this check
will always fail and return -EINVAL.
So, lets move this check to .config_init_once as at that point individual
PHY interface modes should be populated.
Fixes: d1cb613efb ("net: phy: qcom: add support for QCA807x PHY Family")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240212115043.1725918-1-robimarko@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
QCA8072/5 have up to 2 LEDs attached for PHY.
LEDs can be configured to be ON/hw blink or be set to HW control.
Hw blink mode is set to blink at 4Hz or 250ms.
PHY can support both copper (TP) or fiber (FIBRE) kind and supports
different HW control modes based on the port type.
HW control modes supported for netdev trigger for copper ports are:
- LINK_10
- LINK_100
- LINK_1000
- TX
- RX
- FULL_DUPLEX
- HALF_DUPLEX
HW control modes supported for netdev trigger for fiber ports are:
- LINK_100
- LINK_1000
- TX
- RX
- FULL_DUPLEX
- HALF_DUPLEX
LED support conflicts with GPIO controller feature and must be disabled
if gpio-controller is used for the PHY.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generalize some qca808x LED functions in preparation for qca807x LED
support.
The LED implementation of qca808x and qca807x is the same but qca807x
supports also Fiber port and have different hw control bits for Fiber
port. To limit code duplication introduce micro functions that takes reg
instead of LED index to tweak all the supported LED modes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LED implementation of qca808x and qca807x is the same but qca807x
supports also Fiber port and have different hw control bits for Fiber
port.
In preparation for qca807x introduction, move all the common define to
shared header.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds driver for the Qualcomm QCA8072 and QCA8075 PHY-s.
They are 2 or 5 port IEEE 802.3 clause 22 compliant 10BASE-Te,
100BASE-TX and 1000BASE-T PHY-s.
They feature 2 SerDes, one for PSGMII or QSGMII connection with
MAC, while second one is SGMII for connection to MAC or fiber.
Both models have a combo port that supports 1000BASE-X and
100BASE-FX fiber.
PHY package can be configured in 3 mode following this table:
First Serdes mode Second Serdes mode
Option 1 PSGMII for copper Disabled
ports 0-4
Option 2 PSGMII for copper 1000BASE-X / 100BASE-FX
ports 0-4
Option 3 QSGMII for copper SGMII for
ports 0-3 copper port 4
Each PHY inside of QCA807x series has 4 digitally controlled
output only pins that natively drive LED-s.
But some vendors used these to driver generic LED-s controlled
by userspace, so lets enable registering each PHY as GPIO
controller and add driver for it.
These are commonly used in Qualcomm IPQ40xx, IPQ60xx and IPQ807x
boards.
Co-developed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY driver might require additional regs call after
genphy_c37_read_status() is called.
Expand genphy_c37_read_status to provide a bool wheather the link has
changed or not to permit PHY driver to skip additional regs call if
nothing has changed.
Every user of genphy_c37_read_status() is updated with the new
additional bool.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move more function to shared library in preparation for introduction of
new PHY Family qca807x that will make use of both functions from at803x
and qca808x as it's a transition PHY with some implementation of at803x
and some from the new qca808x.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca808x PHY provide support for the led_polarity_set OP to configure
and apply the active-low property but on PHY reset, the Active High bit
is not set resulting in the LED driven as active-low.
To fix this, check if active-low is not set in DT and enable Active High
polarity by default to restore correct funcionality of the LED.
Fixes: 7196062b64 ("net: phy: at803x: add LED support for qca808x")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In switching to using phy_modify_mmd and a more short version of the
LED ON/OFF condition in later revision, it was made a logic error where
value ? QCA808X_LED_FORCE_ON : QCA808X_LED_FORCE_OFF is always true as
value is always OR with QCA808X_LED_FORCE_EN due to missing ()
resulting in the testing condition being QCA808X_LED_FORCE_EN | value.
Add the () to apply the correct condition and restore correct
functionality of the brightness ON/OFF.
Fixes: 7196062b64 ("net: phy: at803x: add LED support for qca808x")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Almost all the QCA8081 PHY driver OPs are specific and only some of them
use the generic at803x.
To make the at803x code slimmer, move all the specific qca808x regs and
functions to a dedicated PHY driver.
Probe function and priv struct is reworked to allocate and use only the
qca808x specific data. Unused data from at803x PHY driver are dropped
from at803x priv struct.
Also a new Kconfig is introduced QCA808X_PHY, to compile the newly
introduced PHY driver for QCA8081 PHY.
As the Kconfig name starts with Qualcomm the same order is kept.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240129141600.2592-6-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move additional functions to shared library in preparation for qca808x
PHY Family to be detached from at803x driver.
Only the shared defines are moved to the shared qcom.h header.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240129141600.2592-5-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Deatch qca83xx PHY driver from at803x.
The QCA83xx PHYs implement specific function and doesn't use generic
at803x so it can be detached from the driver and moved to a dedicated
one.
Probe function and priv struct is reimplemented to allocate and use
only the qca83xx specific data. Unused data from at803x PHY driver
are dropped from at803x priv struct.
This is to make slimmer PHY drivers instead of including lots of bloat
that would never be used in specific SoC.
A new Kconfig flag QCA83XX_PHY is introduced to compile the new
introduced PHY driver.
As the Kconfig name starts with Qualcomm the same order is kept.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240129141600.2592-4-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create and move functions to shared library in preparation for qca83xx
PHY Family to be detached from at803x driver.
Only the shared defines are moved to the shared qcom.h header.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240129141600.2592-3-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for addition of other Qcom PHY and to tidy things up,
move the at803x PHY driver to dedicated directory.
The same order in the Kconfig selection is saved.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240129141600.2592-2-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
