Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
kernel/bpf/verifier.c
829955981c ("bpf: Fix verifier log for async callback return values")
a923819fb2 ("bpf: Treat first argument as return value for bpf_throw")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add phylink capabilities for dsa_loop, which I believe being a software
construct means that it supports essentially all interface types and
all speeds.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add phylink capabilities for vsc73xx. Although this switch driver does
populates the .adjust_link method, dsa_slave_phy_setup() will still be
used to create phylink instances for the LAN ports, although phylink
won't be used for shared links.
There are two different classes of switch - 5+1 and 8 port. The 5+1
port switches uses port indicies 0-4 for the user interfaces and 6 for
the CPU port. The 8 port is confusing - some comments in the driver
imply that port index 7 is used, but the driver actually still uses 6,
so that is what we go with. Also, there appear to be no DTs in the
kernel tree that are using the 8 port variety.
It also looks like port 5 is always skipped.
The switch supports 10M, 100M and 1G speeds. It is not clear whether
all these speeds are supported on the CPU interface. It also looks like
symmetric pause is supported, whether asymmetric pause is as well is
unclear. However, it looks like the pause configuration is entirely
static, and doesn't depend on negotiation results.
So, let's do the best effort we can based on the information found in
the driver when creating vsc73xx_phylink_get_caps().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Address an issue in ksz9477_acl_move_entries() where, in the scenario
(src_idx == dst_idx), ksz9477_validate_and_get_src_count() returns 0,
leading to usage of uninitialized src_count and dst_count variables,
which causes undesired behavior as it attempts to move ACL entries
around.
Fixes: 002841be13 ("net: dsa: microchip: Add partial ACL support for ksz9477 switches")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231006115822.144152-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Besides the QCA8337 switch the Turris 1.x device has on it's MDIO bus
also Micron ethernet PHY (dedicated to the WAN port).
We've been experiencing a strange behavior of the WAN ethernet
interface, wherein the WAN PHY started timing out the MDIO accesses, for
example when the interface was brought down and then back up.
Bisecting led to commit 2cd5485663 ("net: dsa: qca8k: add support for
phy read/write with mgmt Ethernet"), which added support to access the
QCA8337 switch's internal PHYs via management ethernet frames.
Connecting the MDIO bus pins onto an oscilloscope, I was able to see
that the MDIO bus was active whenever a request to read/write an
internal PHY register was done via an management ethernet frame.
My theory is that when the switch core always communicates with the
internal PHYs via the MDIO bus, even when externally we request the
access via ethernet. This MDIO bus is the same one via which the switch
and internal PHYs are accessible to the board, and the board may have
other devices connected on this bus. An ASCII illustration may give more
insight:
+---------+
+----| |
| | WAN PHY |
| +--| |
| | +---------+
| |
| | +----------------------------------+
| | | QCA8337 |
MDC | | | +-------+ |
------o-+--|--------o------------o--| | |
MDIO | | | | | PHY 1 |-|--to RJ45
--------o--|---o----+---------o--+--| | |
| | | | | +-------+ |
| +-------------+ | o--| | |
| | MDIO MDC | | | | PHY 2 |-|--to RJ45
eth1 | | | o--+--| | |
-----------|-|port0 | | | +-------+ |
| | | | o--| | |
| | switch core | | | | PHY 3 |-|--to RJ45
| +-------------+ o--+--| | |
| | | +-------+ |
| | o--| ... | |
+----------------------------------+
When we send a request to read an internal PHY register via an ethernet
management frame via eth1, the switch core receives the ethernet frame
on port 0 and then communicates with the internal PHY via MDIO. At this
time, other potential devices, such as the WAN PHY on Turris 1.x, cannot
use the MDIO bus, since it may cause a bus conflict.
Fix this issue by locking the MDIO bus even when we are accessing the
PHY registers via ethernet management frames.
Fixes: 2cd5485663 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c766e077d9 ("net: dsa: qca8k: convert to regmap read/write
API") introduced bulk read/write methods to qca8k's regmap.
The regmap bulk read/write methods get the register address in a buffer
passed as a void pointer parameter (the same buffer contains also the
read/written values). The register address occupies only as many bytes
as it requires at the beginning of this buffer. For example if the
.reg_bits member in regmap_config is 16 (as is the case for this
driver), the register address occupies only the first 2 bytes in this
buffer, so it can be cast to u16.
But the original commit implementing these bulk read/write methods cast
the buffer to u32:
u32 reg = *(u32 *)reg_buf & U16_MAX;
taking the first 4 bytes. This works on little endian systems where the
first 2 bytes of the buffer correspond to the low 16-bits, but it
obviously cannot work on big endian systems.
Fix this by casting the beginning of the buffer to u16 as
u32 reg = *(u16 *)reg_buf;
Fixes: c766e077d9 ("net: dsa: qca8k: convert to regmap read/write API")
Signed-off-by: Marek Behún <kabel@kernel.org>
Tested-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the mt753x_phylink_pcs_link_up() function for two reasons:
1) priv->pcs[i].pcs.neg_mode is set true, meaning it doesn't take a
MLO_AN_FIXED anymore, but one of PHYLINK_PCS_NEG_*. However, this
is inconsequential due to...
2) priv->pcs[port].pcs.ops is always initialised to point at
mt7530_pcs_ops, which does not have a pcs_link_up() member.
So, let's remove mt753x_phylink_pcs_link_up() entirely.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1qlTQS-008BWe-Va@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds functions for providing in KSZ9477 switch HSR
(High-availability Seamless Redundancy) hardware offloading.
According to AN3474 application note following features are provided:
- TX packet duplication from host to switch (NETIF_F_HW_HSR_DUP)
- RX packet duplication discarding
- Prevention of packet loop
For last two ones - there is a probability that some packets will not
be filtered in HW (in some special cases - described in AN3474).
Hence, the HSR core code shall be used to discard those not caught frames.
Moreover, some switch registers adjustments are required - like setting
MAC address of HSR network interface.
Additionally, the KSZ9477 switch has been configured to forward frames
between HSR ports (e.g. 1,2) members to provide support for
NETIF_F_HW_HSR_FWD flag.
Join and leave functions are written in a way, that are executed with
single port - i.e. configuration is NOT done only when second HSR port
is configured.
Co-developed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Defining macros which have the same name but different values is bad
practice, because it makes it hard to avoid code duplication. The same
code does different things, depending on the file it's placed in.
Case in point, we want to access REG_SW_MAC_ADDR from ksz_common.c, but
currently we can't, because we don't know which kszXXXX_reg.h to include
from the common code.
Remove the REG_SW_MAC_ADDR_{0..5} macros from ksz8795_reg.h and
ksz9477_reg.h, and re-add this register offset to the dev->info->regs[]
array.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Drivers can provide meaningful error messages which state a reason why
they can't perform an offload, and dsa_slave_changeupper() already has
the infrastructure to propagate these over netlink rather than printing
to the kernel log. So pass the extack argument and modify the xrs700x
driver's port_hsr_join() prototype.
Also take the opportunity and use the extack for the 2 -EOPNOTSUPP cases
from xrs700x_hsr_join().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since commit 23d775f12d ("net: dsa: mv88e6xxx: Wait for EEPROM done
before HW reset") the following error is seen on a imx8mn board with
a 88E6320 switch:
mv88e6085 30be0000.ethernet-1:00: Timeout waiting for EEPROM done
This board does not have an EEPROM attached to the switch though.
This problem is well explained by Andrew Lunn:
"If there is an EEPROM, and the EEPROM contains a lot of data, it could
be that when we perform a hardware reset towards the end of probe, it
interrupts an I2C bus transaction, leaving the I2C bus in a bad state,
and future reads of the EEPROM do not work.
The work around for this was to poll the EEInt status and wait for it
to go true before performing the hardware reset.
However, we have discovered that for some boards which do not have an
EEPROM, EEInt never indicates complete. As a result,
mv88e6xxx_g1_wait_eeprom_done() spins for a second and then prints a
warning.
We probably need a different solution than calling
mv88e6xxx_g1_wait_eeprom_done(). The datasheet for 6352 documents the
EEPROM Command register:
bit 15 is:
EEPROM Unit Busy. This bit must be set to a one to start an EEPROM
operation (see EEOp below). Only one EEPROM operation can be
executing at one time so this bit must be zero before setting it to
a one. When the requested EEPROM operation completes this bit will
automatically be cleared to a zero. The transition of this bit from
a one to a zero can be used to generate an interrupt (the EEInt in
Global 1, offset 0x00).
and more interesting is bit 11:
Register Loader Running. This bit is set to one whenever the
register loader is busy executing instructions contained in the
EEPROM."
Change to using mv88e6xxx_g2_eeprom_wait() to fix the timeout error
when the EEPROM chip is not present.
Fixes: 23d775f12d ("net: dsa: mv88e6xxx: Wait for EEPROM done before HW reset")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate read-only const arrays on the stack, instead make them
static.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230919093606.24446-1-colin.i.king@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Don't populate the const read-only array lanes on the stack, instead make
it static.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert these drivers from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert these drivers from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds partial Access Control List (ACL) support for the
ksz9477 family of switches. ACLs enable filtering of incoming layer 2
MAC, layer 3 IP, and layer 4 TCP/UDP packets on each port. They provide
additional capabilities for filtering routed network protocols and can
take precedence over other forwarding functions.
ACLs can filter ingress traffic based on header fields such as
source/destination MAC address, EtherType, IPv4 address, IPv4 protocol,
UDP/TCP ports, and TCP flags. The ACL is an ordered list of up to 16
access control rules programmed into the ACL Table. Each entry specifies
a set of matching conditions and action rules for controlling packet
forwarding and priority.
The ACL also implements a count function, generating an interrupt
instead of a forwarding action. It can be used as a watchdog timer or an
event counter. The ACL consists of three parts: matching rules, action
rules, and processing entries. Multiple match conditions can be either
AND'ed or OR'ed together.
This patch introduces support for a subset of the available ACL
functionality, specifically layer 2 matching and prioritization of
matched packets. For example:
tc qdisc add dev lan2 clsact
tc filter add dev lan2 ingress protocol 0x88f7 flower action skbedit prio 7
tc qdisc add dev lan1 clsact
tc filter add dev lan1 ingress protocol 0x88f7 flower action skbedit prio 7
The hardware offloading implementation was benchmarked against a
configuration without hardware offloading. This latter setup relied on a
software-based Linux bridge. No noticeable differences were observed
between the two configurations. Here is an example of software-based
test:
ip l s dev enu1u1 up
ip l s dev enu1u2 up
ip l s dev enu1u4 up
ethtool -A enu1u1 autoneg off rx off tx off
ethtool -A enu1u2 autoneg off rx off tx off
ethtool -A enu1u4 autoneg off rx off tx off
ip l a name br0 type bridge
ip l s dev br0 up
ip l s enu1u1 master br0
ip l s enu1u2 master br0
ip l s enu1u4 master br0
tc qdisc add dev enu1u1 root handle 1: ets strict 4 priomap 3 3 2 2 1 1 0 0
tc qdisc add dev enu1u4 root handle 1: ets strict 4 priomap 3 3 2 2 1 1 0 0
tc qdisc add dev enu1u2 root handle 1: ets strict 4 priomap 3 3 2 2 1 1 0 0
tc qdisc add dev enu1u1 clsact
tc filter add dev enu1u1 ingress protocol ipv4 flower action skbedit prio 7
tc qdisc add dev enu1u4 clsact
tc filter add dev enu1u4 ingress protocol ipv4 flower action skbedit prio 0
On a system attached to the port enu1u2 I run two iperf3 server
instances:
iperf3 -s -p 5210 &
iperf3 -s -p 5211 &
On systems attached to enu1u4 and enu1u1 I run:
iperf3 -u -c 172.17.0.1 -p 5210 -b100M -l1472 -t100
and
iperf3 -u -c 172.17.0.1 -p 5211 -b100M -l1472 -t100
As a result, IP traffic on port enu1u1 will be prioritized and take
precedence over IP traffic on port enu1u4
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, the *_port_setup code is in dsa_switch_ops::port_enable(),
which is not the best place for it. This patch moves it to a more
suitable place, dsa_switch_ops::port_setup(), to match the function's
purpose and name.
This patch is a preparation for coming ACL support patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree based drive strength configuration support. It is needed to
pass EMI validation on our hardware.
Configuration values are based on the vendor's reference driver.
Tested on KSZ9563R.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We auto-negotiate most ports in the RTL8366RB driver, but
the CPU port is hard-coded to 1Gbit, full duplex, tx and
rx pause.
This isn't very nice. People may configure speed and
duplex differently in the device tree.
Actually respect the arguments passed to the function for
the CPU port, which get passed properly after Russell's
patch "net: dsa: realtek: add phylink_get_caps implementation"
After this the link is still set up properly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when we add the first sja1105 port to a bridge with
vlan_filtering 1, then we sometimes see this output:
sja1105 spi2.2: port 4 failed to read back entry for be:79:b4:9e:9e:96 vid 3088: -ENOENT
sja1105 spi2.2: Reset switch and programmed static config. Reason: VLAN filtering
sja1105 spi2.2: port 0 failed to add be:79:b4:9e:9e:96 vid 0 to fdb: -2
It is because sja1105_fdb_add() runs from the dsa_owq which is no longer
serialized with switch resets since it dropped the rtnl_lock() in the
blamed commit.
Either performing the FDB accesses before the reset, or after the reset,
is equally fine, because sja1105_static_fdb_change() backs up those
changes in the static config, but FDB access during reset isn't ok.
Make sja1105_static_config_reload() take the fdb_lock to fix that.
Fixes: 0faf890fc5 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sja1105_fdb_add() runs from the dsa_owq, and sja1105_port_mcast_flood()
runs from switchdev_deferred_process_work(). Prior to the blamed commit,
they used to be indirectly serialized through the rtnl_lock(), which
no longer holds true because dsa_owq dropped that.
So, it is now possible that we traverse the static config BLK_IDX_L2_LOOKUP
elements concurrently compared to when we change them, in
sja1105_static_fdb_change(). That is not ideal, since it might result in
data corruption.
Introduce a mutex which serializes accesses to the hardware FDB and to
the static config elements for the L2 Address Lookup table.
I can't find a good reason to add locking around sja1105_fdb_dump().
I'll add it later if needed.
Fixes: 0faf890fc5 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit cited in Fixes: did 2 things: it refactored the read-back
polling from sja1105_dynamic_config_read() into a new function,
sja1105_dynamic_config_wait_complete(), and it called that from
sja1105_dynamic_config_write() too.
What is problematic is the refactoring.
The refactored code from sja1105_dynamic_config_poll_valid() works like
the previous one, but the problem is that it uses another packed_buf[]
SPI buffer, and there was code at the end of sja1105_dynamic_config_read()
which was relying on the read-back packed_buf[]:
/* Don't dereference possibly NULL pointer - maybe caller
* only wanted to see whether the entry existed or not.
*/
if (entry)
ops->entry_packing(packed_buf, entry, UNPACK);
After the change, the packed_buf[] that this code sees is no longer the
entry read back from hardware, but the original entry that the caller
passed to the sja1105_dynamic_config_read(), packed into this buffer.
This difference is the most notable with the SJA1105_SEARCH uses from
sja1105pqrs_fdb_add() - used for both fdb and mdb. There, we have logic
added by commit 728db843df ("net: dsa: sja1105: ignore the FDB entry
for unknown multicast when adding a new address") to figure out whether
the address we're trying to add matches on any existing hardware entry,
with the exception of the catch-all multicast address.
That logic was broken, because with sja1105_dynamic_config_read() not
working properly, it doesn't return us the entry read back from
hardware, but the entry that we passed to it. And, since for multicast,
a match will always exist, it will tell us that any mdb entry already
exists at index=0 L2 Address Lookup table. It is index=0 because the
caller doesn't know the index - it wants to find it out, and
sja1105_dynamic_config_read() does:
if (index < 0) { // SJA1105_SEARCH
/* Avoid copying a signed negative number to an u64 */
cmd.index = 0; // <- this
cmd.search = true;
} else {
cmd.index = index;
cmd.search = false;
}
So, to the caller of sja1105_dynamic_config_read(), the returned info
looks entirely legit, and it will add all mdb entries to FDB index 0.
There, they will always overwrite each other (not to mention,
potentially they can also overwrite a pre-existing bridge fdb entry),
and the user-visible impact will be that only the last mdb entry will be
forwarded as it should. The others won't (will be flooded or dropped,
depending on the egress flood settings).
Fixing is a bit more complicated, and involves either passing the same
packed_buf[] to sja1105_dynamic_config_wait_complete(), or moving all
the extra processing on the packed_buf[] to
sja1105_dynamic_config_wait_complete(). I've opted for the latter,
because it makes sja1105_dynamic_config_wait_complete() a bit more
self-contained.
Fixes: df405910ab ("net: dsa: sja1105: wait for dynamic config command completion on writes too")
Reported-by: Yanan Yang <yanan.yang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, sja1105_dynamic_config_wait_complete() returns either 0 or
-ETIMEDOUT, because it just looks at the read_poll_timeout() return code.
There will be future changes which move some more checks to
sja1105_dynamic_config_poll_valid(). It is important that we propagate
their exact return code (-ENOENT, -EINVAL), because callers of
sja1105_dynamic_config_read() depend on them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4d94235495 ("net: dsa: sja1105: offload bridge port flags to
device") has partially hidden some multicast entries from showing up in
the "bridge fdb show" output, but it wasn't enough. Addresses which are
added through "bridge mdb add" still show up. Hide them all.
Fixes: 291d1e72b7 ("net: dsa: sja1105: Add support for FDB and MDB management")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9477 errata points out (in 'Module 4') the link up/down problems
when EEE (Energy Efficient Ethernet) is enabled in the device to which
the KSZ9477 tries to auto negotiate.
The suggested workaround is to clear advertisement of EEE for PHYs in
this chip driver.
To avoid regressions with other switch ICs the new MICREL_NO_EEE flag
has been introduced.
Moreover, the in-register disablement of MMD_DEVICE_ID_EEE_ADV.MMD_EEE_ADV
MMD register is removed, as this code is both; now executed too late
(after previous rework of the PHY and DSA for KSZ switches) and not
required as setting all members of eee_broken_modes bit field prevents
the KSZ9477 from advertising EEE.
Fixes: 69d3b36ca0 ("net: dsa: microchip: enable EEE support") # for KSZ9477
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # Confirmed disabled EEE with oscilloscope.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230905093315.784052-1-lukma@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The blamed commit left this delta behind:
struct sja1105_cbs_entry {
- u64 port;
- u64 prio;
+ u64 port; /* Not used for SJA1110 */
+ u64 prio; /* Not used for SJA1110 */
u64 credit_hi;
u64 credit_lo;
u64 send_slope;
u64 idle_slope;
};
but did not actually implement tc-cbs offload fully for the new switch.
The offload is accepted, but it doesn't work.
The difference compared to earlier switch generations is that now, the
table of CBS shapers is sparse, because there are many more shapers, so
the mapping between a {port, prio} and a table index is static, rather
than requiring us to store the port and prio into the sja1105_cbs_entry.
So, the problem is that the code programs the CBS shaper parameters at a
dynamic table index which is incorrect.
All that needs to be done for SJA1110 CBS shapers to work is to bypass
the logic which allocates shapers in a dense manner, as for SJA1105, and
use the fixed mapping instead.
Fixes: 3e77e59bf8 ("net: dsa: sja1105: add support for the SJA1110 switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After running command [2] too many times in a row:
[1] $ tc qdisc add dev sw2p0 root handle 1: mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0
[2] $ tc qdisc replace dev sw2p0 parent 1:1 cbs offload 1 \
idleslope 120000 sendslope -880000 locredit -1320 hicredit 180
(aka more than priv->info->num_cbs_shapers times)
we start seeing the following error message:
Error: Specified device failed to setup cbs hardware offload.
This comes from the fact that ndo_setup_tc(TC_SETUP_QDISC_CBS) presents
the same API for the qdisc create and replace cases, and the sja1105
driver fails to distinguish between the 2. Thus, it always thinks that
it must allocate the same shaper for a {port, queue} pair, when it may
instead have to replace an existing one.
Fixes: 4d7525085a ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More careful measurement of the tc-cbs bandwidth shows that the stream
bandwidth (effectively idleslope) increases, there is a larger and
larger discrepancy between the rate limit obtained by the software
Qdisc, and the rate limit obtained by its offloaded counterpart.
The discrepancy becomes so large, that e.g. at an idleslope of 40000
(40Mbps), the offloaded cbs does not actually rate limit anything, and
traffic will pass at line rate through a 100 Mbps port.
The reason for the discrepancy is that the hardware documentation I've
been following is incorrect. UM11040.pdf (for SJA1105P/Q/R/S) states
about IDLE_SLOPE that it is "the rate (in unit of bytes/sec) at which
the credit counter is increased".
Cross-checking with UM10944.pdf (for SJA1105E/T) and UM11107.pdf
(for SJA1110), the wording is different: "This field specifies the
value, in bytes per second times link speed, by which the credit counter
is increased".
So there's an extra scaling for link speed that the driver is currently
not accounting for, and apparently (empirically), that link speed is
expressed in Kbps.
I've pondered whether to pollute the sja1105_mac_link_up()
implementation with CBS shaper reprogramming, but I don't think it is
worth it. IMO, the UAPI exposed by tc-cbs requires user space to
recalculate the sendslope anyway, since the formula for that depends on
port_transmit_rate (see man tc-cbs), which is not an invariant from tc's
perspective.
So we use the offload->sendslope and offload->idleslope to deduce the
original port_transmit_rate from the CBS formula, and use that value to
scale the offload->sendslope and offload->idleslope to values that the
hardware understands.
Some numerical data points:
40Mbps stream, max interfering frame size 1500, port speed 100M
---------------------------------------------------------------
tc-cbs parameters:
idleslope 40000 sendslope -60000 locredit -900 hicredit 600
which result in hardware values:
Before (doesn't work) After (works)
credit_hi 600 600
credit_lo 900 900
send_slope 7500000 75
idle_slope 5000000 50
40Mbps stream, max interfering frame size 1500, port speed 1G
-------------------------------------------------------------
tc-cbs parameters:
idleslope 40000 sendslope -960000 locredit -1440 hicredit 60
which result in hardware values:
Before (doesn't work) After (works)
credit_hi 60 60
credit_lo 1440 1440
send_slope 120000000 120
idle_slope 5000000 5
5.12Mbps stream, max interfering frame size 1522, port speed 100M
-----------------------------------------------------------------
tc-cbs parameters:
idleslope 5120 sendslope -94880 locredit -1444 hicredit 77
which result in hardware values:
Before (doesn't work) After (works)
credit_hi 77 77
credit_lo 1444 1444
send_slope 11860000 118
idle_slope 640000 6
Tested on SJA1105T, SJA1105S and SJA1110A, at 1Gbps and 100Mbps.
Fixes: 4d7525085a ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Reported-by: Yanan Yang <yanan.yang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/process/license-rules.rst and checkpatch expect the SPDX
identifier syntax for multiple licenses to use capital "OR". Correct it
to keep consistent format and avoid copy-paste issues.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: FLorian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230823085632.116725-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove debug logs in port vlan management, since there are already multiple
tracepoints defined for those operations in DSA
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 91a98917a8 ("net: dsa: microchip: move switch chip_id detection to ksz_common")
removed ksz8_switch_detect() but not its declaration.
Commit 6ec23aaaac ("net: dsa: microchip: move ksz_dev_ops to ksz_common.c")
declared but never implemented other functions.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230821125501.19624-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The user ports use RSGMII, but we don't have that, and DT doesn't
specify a phy interface mode, so phylib defaults to GMII. These support
1G, 100M and 10M with flow control. It is unknown whether asymetric
pause is supported at all speeds.
The CPU port uses MII/GMII/RGMII/REVMII by hardware pin strapping,
and support speeds specific to each, with full duplex only supported
in some modes. Flow control may be supported again by hardware pin
strapping, and theoretically is readable through a register but no
information is given in the datasheet for that.
So, we do a best efforts - and be lenient.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
802.1X PAE frames are link-local frames, therefore they must be trapped to
the CPU port. Currently, the MT753X switches treat 802.1X PAE frames as
regular multicast frames, therefore flooding them to user ports. To fix
this, set 802.1X PAE frames to be trapped to the CPU port(s).
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit resolved a bug where frames would still get stuck at
egress, even though they're smaller than the maxSDU[tc], because the
driver did not take into account the extra 33 ns that the queue system
needs for scheduling the frame.
It now takes that into account, but the arithmetic that we perform in
vsc9959_tas_remaining_gate_len_ps() is buggy, because we operate on
64-bit unsigned integers, so gate_len_ns - VSC9959_TAS_MIN_GATE_LEN_NS
may become a very large integer if gate_len_ns < 33 ns.
In practice, this means that we've introduced a regression where all
traffic class gates which are permanently closed will not get detected
by the driver, and we won't enable oversize frame dropping for them.
Before:
mscc_felix 0000:00:00.5: port 0: max frame size 1526 needs 12400000 ps, 1152000 ps for mPackets at speed 1000
mscc_felix 0000:00:00.5: port 0 tc 0 min gate len 1000000, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 1 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 2 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 3 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 4 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 5 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 6 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 5120 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 615 octets including FCS
After:
mscc_felix 0000:00:00.5: port 0: max frame size 1526 needs 12400000 ps, 1152000 ps for mPackets at speed 1000
mscc_felix 0000:00:00.5: port 0 tc 0 min gate len 1000000, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 5120 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 615 octets including FCS
Fixes: 11afdc6526 ("net: dsa: felix: tc-taprio intervals smaller than MTU should send at least one packet")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230817120111.3522827-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
