This patch adds functions for providing in KSZ9477 switch HSR
(High-availability Seamless Redundancy) hardware offloading.
According to AN3474 application note following features are provided:
- TX packet duplication from host to switch (NETIF_F_HW_HSR_DUP)
- RX packet duplication discarding
- Prevention of packet loop
For last two ones - there is a probability that some packets will not
be filtered in HW (in some special cases - described in AN3474).
Hence, the HSR core code shall be used to discard those not caught frames.
Moreover, some switch registers adjustments are required - like setting
MAC address of HSR network interface.
Additionally, the KSZ9477 switch has been configured to forward frames
between HSR ports (e.g. 1,2) members to provide support for
NETIF_F_HW_HSR_FWD flag.
Join and leave functions are written in a way, that are executed with
single port - i.e. configuration is NOT done only when second HSR port
is configured.
Co-developed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Defining macros which have the same name but different values is bad
practice, because it makes it hard to avoid code duplication. The same
code does different things, depending on the file it's placed in.
Case in point, we want to access REG_SW_MAC_ADDR from ksz_common.c, but
currently we can't, because we don't know which kszXXXX_reg.h to include
from the common code.
Remove the REG_SW_MAC_ADDR_{0..5} macros from ksz8795_reg.h and
ksz9477_reg.h, and re-add this register offset to the dev->info->regs[]
array.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch adds partial Access Control List (ACL) support for the
ksz9477 family of switches. ACLs enable filtering of incoming layer 2
MAC, layer 3 IP, and layer 4 TCP/UDP packets on each port. They provide
additional capabilities for filtering routed network protocols and can
take precedence over other forwarding functions.
ACLs can filter ingress traffic based on header fields such as
source/destination MAC address, EtherType, IPv4 address, IPv4 protocol,
UDP/TCP ports, and TCP flags. The ACL is an ordered list of up to 16
access control rules programmed into the ACL Table. Each entry specifies
a set of matching conditions and action rules for controlling packet
forwarding and priority.
The ACL also implements a count function, generating an interrupt
instead of a forwarding action. It can be used as a watchdog timer or an
event counter. The ACL consists of three parts: matching rules, action
rules, and processing entries. Multiple match conditions can be either
AND'ed or OR'ed together.
This patch introduces support for a subset of the available ACL
functionality, specifically layer 2 matching and prioritization of
matched packets. For example:
tc qdisc add dev lan2 clsact
tc filter add dev lan2 ingress protocol 0x88f7 flower action skbedit prio 7
tc qdisc add dev lan1 clsact
tc filter add dev lan1 ingress protocol 0x88f7 flower action skbedit prio 7
The hardware offloading implementation was benchmarked against a
configuration without hardware offloading. This latter setup relied on a
software-based Linux bridge. No noticeable differences were observed
between the two configurations. Here is an example of software-based
test:
ip l s dev enu1u1 up
ip l s dev enu1u2 up
ip l s dev enu1u4 up
ethtool -A enu1u1 autoneg off rx off tx off
ethtool -A enu1u2 autoneg off rx off tx off
ethtool -A enu1u4 autoneg off rx off tx off
ip l a name br0 type bridge
ip l s dev br0 up
ip l s enu1u1 master br0
ip l s enu1u2 master br0
ip l s enu1u4 master br0
tc qdisc add dev enu1u1 root handle 1: ets strict 4 priomap 3 3 2 2 1 1 0 0
tc qdisc add dev enu1u4 root handle 1: ets strict 4 priomap 3 3 2 2 1 1 0 0
tc qdisc add dev enu1u2 root handle 1: ets strict 4 priomap 3 3 2 2 1 1 0 0
tc qdisc add dev enu1u1 clsact
tc filter add dev enu1u1 ingress protocol ipv4 flower action skbedit prio 7
tc qdisc add dev enu1u4 clsact
tc filter add dev enu1u4 ingress protocol ipv4 flower action skbedit prio 0
On a system attached to the port enu1u2 I run two iperf3 server
instances:
iperf3 -s -p 5210 &
iperf3 -s -p 5211 &
On systems attached to enu1u4 and enu1u1 I run:
iperf3 -u -c 172.17.0.1 -p 5210 -b100M -l1472 -t100
and
iperf3 -u -c 172.17.0.1 -p 5211 -b100M -l1472 -t100
As a result, IP traffic on port enu1u1 will be prioritized and take
precedence over IP traffic on port enu1u4
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, the *_port_setup code is in dsa_switch_ops::port_enable(),
which is not the best place for it. This patch moves it to a more
suitable place, dsa_switch_ops::port_setup(), to match the function's
purpose and name.
This patch is a preparation for coming ACL support patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree based drive strength configuration support. It is needed to
pass EMI validation on our hardware.
Configuration values are based on the vendor's reference driver.
Tested on KSZ9563R.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9477 errata points out (in 'Module 4') the link up/down problems
when EEE (Energy Efficient Ethernet) is enabled in the device to which
the KSZ9477 tries to auto negotiate.
The suggested workaround is to clear advertisement of EEE for PHYs in
this chip driver.
To avoid regressions with other switch ICs the new MICREL_NO_EEE flag
has been introduced.
Moreover, the in-register disablement of MMD_DEVICE_ID_EEE_ADV.MMD_EEE_ADV
MMD register is removed, as this code is both; now executed too late
(after previous rework of the PHY and DSA for KSZ switches) and not
required as setting all members of eee_broken_modes bit field prevents
the KSZ9477 from advertising EEE.
Fixes: 69d3b36ca0 ("net: dsa: microchip: enable EEE support") # for KSZ9477
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # Confirmed disabled EEE with oscilloscope.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230905093315.784052-1-lukma@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit (SHA1: 5c844d57aa) provided code
to apply "Module 6: Certain PHY registers must be written as pairs instead
of singly" errata for KSZ9477 as this chip for certain PHY registers
(0xN120 to 0xN13F, N=1,2,3,4,5) must be accesses as 32 bit words instead
of 16 or 8 bit access.
Otherwise, adjacent registers (no matter if reserved or not) are
overwritten with 0x0.
Without this patch some registers (e.g. 0x113c or 0x1134) required for 32
bit access are out of valid regmap ranges.
As a result, following error is observed and KSZ9477 is not properly
configured:
ksz-switch spi1.0: can't rmw 32bit reg 0x113c: -EIO
ksz-switch spi1.0: can't rmw 32bit reg 0x1134: -EIO
ksz-switch spi1.0 lan1 (uninitialized): failed to connect to PHY: -EIO
ksz-switch spi1.0 lan1 (uninitialized): error -5 setting up PHY for tree 0, switch 0, port 0
The solution is to modify regmap_reg_range to allow accesses with 4 bytes
boundaries.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230724211859.805481-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since DSA no longer marks anything as phylink-legacy, there is now no
need for DSA drivers to set this member to false. Remove all instances
of this.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The KSZ8795 driver code was modified to use on KSZ8863/73, which has
different register definitions. Some of the new KSZ8795 register
information are wrong compared to previous code.
KSZ8795 also behaves differently in that the STATIC_MAC_TABLE_USE_FID
and STATIC_MAC_TABLE_FID bits are off by 1 when doing MAC table reading
than writing. To compensate that a special code was added to shift the
register value by 1 before applying those bits. This is wrong when the
code is running on KSZ8863, so this special code is only executed when
KSZ8795 is detected.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9477 PHY errata handling code has now been moved into the Micrel
PHY driver, so it is no longer needed inside the DSA switch driver.
Remove it.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This update introduces specific register access boundaries for the
KSZ8873 and KSZ8863 chips within the DSA Microchip driver. The outlined
ranges target global control registers, port registers, and advanced
control registers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It is not immediately obvious that this driver allocates, via the
KSZ_REGMAP_TABLE() macro, 3 regmaps for register access: dev->regmap[0]
for 8-bit access, dev->regmap[1] for 16-bit and dev->regmap[2] for
32-bit access.
In future changes that add support for reg_fields, each field will have
to specify through which of the 3 regmaps it's going to go. Add an enum
now, to denote one of the 3 register access widths, and make the code go
through some wrapper functions for easier review and further
modification.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for add/del_fdb operations and utilize the refactored static
MAC table code. This resolves kernel warnings caused by the lack of fdb
add function support in the current driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
FID is directly mapped to VID. However, configuring a MAC address with a
VID != 0 resulted in incorrect configuration due to an incorrect bit
mask. This kernel commit fixed the issue by correcting the bit mask and
ensuring proper configuration of MAC addresses with non-zero VID.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the dynamic MAC table is empty, we will still extract one outdated
entry. Fix it by using correct bit offset.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are using wrong offset, so we will get not a timestamp.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current ksz8_fdb_dump() is able to extract only max 249 entries on
the ksz8863/ksz8873 series of switches. This happened due to wrong
bit mask and offset calculation.
This commit corrects the issue and allows for the complete extraction of
all 1024 entries.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit has replaced a ksz_write8() call to address
REG_PORT_5_CTRL_6 (0x56) with a ksz_set_xmii() -> ksz_pwrite8() call to
regs[P_XMII_CTRL_1], which is also defined as 0x56 for ksz8795_regs[].
The trouble is that, when compared to ksz_write8(), ksz_pwrite8() also
adjusts the register offset with the port base address. So in reality,
ksz_pwrite8(offset=0x56) accesses register 0x56 + 0x50 = 0xa6, which in
this switch appears to be unmapped, and the RGMII delay configuration on
the CPU port does nothing.
So if the switch wasn't fine with the RGMII delay configuration done
through pin strapping and relied on Linux to apply a different one in
order to pass traffic, this is now broken.
Using the offset translation logic imposed by ksz_pwrite8(), the correct
value for regs[P_XMII_CTRL_1] should have been 0x6 on ksz8795_regs[], in
order to really end up accessing register 0x56.
Static code analysis shows that, despite there being multiple other
accesses to regs[P_XMII_CTRL_1] in this driver, the only code path that
is applicable to ksz8795_regs[] and ksz8_dev_ops is ksz_set_xmii().
Therefore, the problem is isolated to RGMII delays.
In its current form, ksz8795_regs[] contains the same value for
P_XMII_CTRL_0 and for P_XMII_CTRL_1, and this raises valid suspicions
that writes made by the driver to regs[P_XMII_CTRL_0] might overwrite
writes made to regs[P_XMII_CTRL_1] or vice versa.
Again, static analysis shows that the only accesses to P_XMII_CTRL_0
from the driver are made from code paths which are not reachable with
ksz8_dev_ops. So the accesses made by ksz_set_xmii() are safe for this
switch family.
[ vladimiroltean: rewrote commit message ]
Fixes: c476bede4b ("net: dsa: microchip: ksz8795: use common xmii function")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230315231916.2998480-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add ETS Qdisc support for KSZ9477 of switches. Current implementation is
limited to strict priority mode.
Tested on KSZ8563R with following configuration:
tc qdisc replace dev lan2 root handle 1: ets strict 4 \
priomap 3 3 2 2 1 1 0 0
ip link add link lan2 name v1 type vlan id 1 \
egress-qos-map 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7
and patched iperf3 version:
https://github.com/esnet/iperf/pull/1476
iperf3 -c 172.17.0.1 -b100M -l1472 -t100 -u -R --sock-prio 2
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ksz_setup_tc_mode() to make queue scheduling and shaping
configuration more visible.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of KSZ9477 family switches provides EEE support. To enable it, we
just need to register set_mac_eee/set_mac_eee handlers and validate
supported chip version and port.
Currently supported chip variants are: KSZ8563, KSZ9477, KSZ9563,
KSZ9567, KSZ9893, KSZ9896, KSZ9897. KSZ8563 supports EEE only with
100BaseTX/Full. Other chips support 100BaseTX/Full and 1000BaseTX/Full.
Low Power Idle configuration is not supported and currently not
documented in the datasheets.
EEE PHY specific tunings are not documented in the switch datasheets, but can
overlap with KSZ9131 specification.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ9477, KSZ9567, KSZ9563, KSZ8563 and LAN937x supports Credit based
shaper. To differentiate the chip supporting cbs, tc_cbs_supported
flag is introduced in ksz_chip_data.
And KSZ series has 16bit Credit increment registers whereas LAN937x has
24bit register. The value to be programmed in the credit increment is
determined using the successive multiplication method to convert decimal
fraction to hexadecimal fraction.
For example: if idleslope is 10000 and sendslope is -90000, then
bandwidth is 10000 - (-90000) = 100000.
The 10% bandwidth of 100Mbps means 10/100 = 0.1(decimal). This value has
to be converted to hexa.
1) 0.1 * 16 = 1.6 --> fraction 0.6 Carry = 1 (MSB)
2) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
3) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
4) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
5) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
6) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9 (LSB)
Now 0.1(decimal) becomes 0.199999(Hex).
If it is LAN937x, 24 bit value will be programmed to Credit Inc
register, 0x199999. For others 16 bit value will be prgrammed, 0x1999.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LAN937x family of switches has 8 queues per port where the KSZ switches
has 4 queues per port. By default, only one queue per port is enabled.
The queues are configurable in 2, 4 or 8. This patch add 8 number of
queues for LAN937x and 4 for other switches.
In the tag_ksz.c file, prioirty of the packet is queried using the skb
buffer and the corresponding value is updated in the tag.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MDIO core should not pass a C45 request via the C22 API call any
more. So remove the tests from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds the routines for transmission of ptp packets. When the
ptp pdelay_req packet to be transmitted, it uses the deferred xmit
worker to schedule the packets.
During irq_setup, interrupt for Sync, Pdelay_req and Pdelay_rsp are
enabled. So interrupt is triggered for all three packets. But for
p2p1step, we require only time stamp of Pdelay_req packet. Hence to
avoid posting of the completion from ISR routine for Sync and
Pdelay_resp packets, ts_en flag is introduced. This controls which
packets need to processed for timestamp.
After the packet is transmitted, ISR is triggered. The time at which
packet transmitted is recorded to separate register.
This value is reconstructed to absolute time and posted to the user
application through socket error queue.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx Timestamping is done through 4 additional bytes in tail tag.
Whenever the ptp packet is received, the 4 byte hardware time stamped
value is added before 1 byte tail tag. Also, bit 7 in tail tag indicates
it as PTP frame. This 4 byte value is extracted from the tail tag and
reconstructed to absolute time and assigned to skb hwtstamp.
If the packet received in PDelay_Resp, then partial ingress timestamp
is subtracted from the correction field. Since user space tools expects
to be done in hardware.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP Interrupt mask and status register differ from the global and port
interrupt mechanism by two methods. One is that for global/port
interrupt enabling we have to clear the bit but for ptp interrupt we
have to set the bit. And other is bit12:0 is reserved in ptp interrupt
registers. This forced to not use the generic implementation of
global/port interrupt method routine. This patch implement the ptp
interrupt mechanism to read the timestamp register for sync, pdelay_req
and pdelay_resp.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the routine for get_ts_info, hwstamp_get, set. This enables
the PTP support towards userspace applications such as linuxptp.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implement routines (adjfine, adjtime, gettime and settime)
for manipulating the chip's PTP clock. It registers the ptp caps
to posix clock register.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com> # mostly api
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ swithes used interrupts for detecting the phy link up and down.
During registering the interrupt handler, it used IRQF_TRIGGER_FALLING
flag. But this flag has to be retrieved from device tree instead of hard
coding in the driver, so removing the flag.
Fixes: ff319a6448 ("net: dsa: microchip: move interrupt handling logic from lan937x to ksz_common")
Reported-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20221213101440.24667-1-arun.ramadoss@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make MTU configurable on KSZ87xx and KSZ88xx series of switches.
Before this patch, pre-configured behavior was different on different
switch series, due to opposite meaning of the same bit:
- KSZ87xx: Reg 4, Bit 1 - if 1, max frame size is 1532; if 0 - 1514
- KSZ88xx: Reg 4, Bit 1 - if 1, max frame size is 1514; if 0 - 1532
Since the code was telling "... SW_LEGAL_PACKET_DISABLE, true)", I
assume, the idea was to set max frame size to 1532.
With this patch, by setting MTU size 1500, both switch series will be
configured to the 1532 frame limit.
This patch was tested on KSZ8873.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are no HW specific registers, so we can process all of them
in one location.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Arun Ramadoss <arun.ramadoss@microchip.com> (KSZ9893 and LAN937x)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
KSZ8563 have three port interrupts: PTP, PHY and ACL. Add
port_nirq as 3 for KSZ8563 inside ksz_chip_data.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add KSZ9563 inside ksz_switch_chips structure with
port_nirq as 3. KSZ9563 use KSZ9893 switch parameters
but port_nirq count is 3 for KSZ9563 whereas 2 for
KSZ9893. Add KSZ9563 inside ksz_switch_chips as a separate
member and from device tree map compatible string into
KSZ9563 inside ksz_spi.c and ksz9477_i2c.c.
Global Chip ID 1 and 2 registers read value 9893, select
sku based on Global Chip ID 4 Register which read 0x1c
for KSZ9563.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The global port interrupt routines and individual ports interrupt
routines has similar implementation except the mask & status register
and number of nested irqs in them. The mask & status register and
pointer to ksz_device is added to ksz_irq and uses the ksz_irq as
irq_chip_data.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To support the phy link detection through interrupt method for ksz9477
based switch, the interrupt handling routines are moved from
lan937x_main.c to ksz_common.c. The only changes made are functions
names are prefixed with ksz_ instead of lan937x_.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the number of port irqs is hard coded for the lan937x switch
as 6. In order to make the generic interrupt handler for ksz switches,
number of port irq supported by the switch is added to the
ksz_chip_data. It is 4 for ksz9477, 2 for ksz9897 and 3 for ksz9567.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
KSZ9477 has the 11 bit ageing count value which is split across the two
registers. And LAN937x has the 20 bit ageing count which is also split
into two registers. Each count in the registers represents 1 second.
This patch add the support for ageing time for KSZ9477 and LAN937x
series of switch.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
According to the KSZ9477S datasheet, there is no global register
at 0x033C and 0x033D addresses.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the KSZ9896 6-port Gigabit Ethernet Switch to the
ksz9477 driver.
Although the KSZ9896 is already listed in the device tree binding
documentation since a1c0ed24fe (dt-bindings: net: dsa: document
additional Microchip KSZ9477 family switches) the chip id
(0x00989600) is not recognized by ksz_switch_detect() and rejected
by the driver.
The KSZ9896 is similar to KSZ9897 but has only one configurable
MII/RMII/RGMII/GMII cpu port.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the interrupts for internal phy link detection for
LAN937x. The interrupt enable bits are active low. There is global
interrupt mask for each port. And each port has the individual interrupt
mask for TAS. QCI, SGMII, PTP, PHY and ACL.
The first level of interrupt domain is registered for global port
interrupt and second level of interrupt domain for the individual port
interrupts. The phy interrupt is enabled in the lan937x_mdio_register
function. Interrupt from which port is raised will be detected based on
the interrupt host data.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct ksz_port doesn't have reference to ksz_device as of now. In order
to find out from which port interrupt has triggered, we need to pass the
struct ksz_port as a host data. When the interrupt is triggered, we can
get the port from which interrupt triggered, but to identify it is phy
interrupt we have to read status register. The regmap structure for
accessing the device register is present in the ksz_device struct. To
access the ksz_device from the ksz_port, the reference is added to it
with port number as well.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
