When the iavf driver wants to reconfigure the VLAN filters
(iavf_add_vlan, iavf_del_vlan), it sets a flag in
aq_required:
adapter->aq_required |= IAVF_FLAG_AQ_ADD_VLAN_FILTER;
or:
adapter->aq_required |= IAVF_FLAG_AQ_DEL_VLAN_FILTER;
This is later processed by the watchdog_task, but it runs periodically
every 2 seconds, so it can be a long time before it processes the request.
In the worst case, the interface is unable to receive traffic for more
than 2 seconds for no objective reason.
Fixes: 5eae00c57f ("i40evf: main driver core")
Signed-off-by: Petr Oros <poros@redhat.com>
Co-developed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Co-developed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add helper for set iavf aq request AVF_FLAG_AQ_* and immediately
schedule watchdog_task. Helper will be used in cases where it is
necessary to run aq requests asap
Signed-off-by: Petr Oros <poros@redhat.com>
Co-developed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Co-developed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Prevent schedule operations for adminq during device remove and when
__IAVF_IN_REMOVE_TASK flag is set. Currently, the iavf_down function
adds operations for adminq that shouldn't be processed when the device
is in the __IAVF_REMOVE state.
Reproduction:
echo 4 > /sys/bus/pci/devices/0000:17:00.0/sriov_numvfs
ip link set dev ens1f0 vf 0 trust on
ip link set dev ens1f0 vf 1 trust on
ip link set dev ens1f0 vf 2 trust on
ip link set dev ens1f0 vf 3 trust on
ip link set dev ens1f0 vf 0 mac 00:22:33:44:55:66
ip link set dev ens1f0 vf 1 mac 00:22:33:44:55:67
ip link set dev ens1f0 vf 2 mac 00:22:33:44:55:68
ip link set dev ens1f0 vf 3 mac 00:22:33:44:55:69
echo 0000:17:02.0 > /sys/bus/pci/devices/0000\:17\:02.0/driver/unbind
echo 0000:17:02.1 > /sys/bus/pci/devices/0000\:17\:02.1/driver/unbind
echo 0000:17:02.2 > /sys/bus/pci/devices/0000\:17\:02.2/driver/unbind
echo 0000:17:02.3 > /sys/bus/pci/devices/0000\:17\:02.3/driver/unbind
sleep 10
echo 0000:17:02.0 > /sys/bus/pci/drivers/iavf/bind
echo 0000:17:02.1 > /sys/bus/pci/drivers/iavf/bind
echo 0000:17:02.2 > /sys/bus/pci/drivers/iavf/bind
echo 0000:17:02.3 > /sys/bus/pci/drivers/iavf/bind
modprobe vfio-pci
echo 8086 154c > /sys/bus/pci/drivers/vfio-pci/new_id
qemu-system-x86_64 -accel kvm -m 4096 -cpu host \
-drive file=centos9.qcow2,if=none,id=virtio-disk0 \
-device virtio-blk-pci,drive=virtio-disk0,bootindex=0 -smp 4 \
-device vfio-pci,host=17:02.0 -net none \
-device vfio-pci,host=17:02.1 -net none \
-device vfio-pci,host=17:02.2 -net none \
-device vfio-pci,host=17:02.3 -net none \
-daemonize -vnc :5
Current result:
There is a probability that the mac of VF in guest is inconsistent with
it in host
Expected result:
When passthrough NIC VF to guest, the VF in guest should always get
the same mac as it in host.
Fixes: 14756b2ae2 ("iavf: Fix __IAVF_RESETTING state usage")
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Previously CRC stripping was always enabled for VF.
Now it is possible to turn off CRC stripping via ethtool:
#ethtool -K <interface> rx-fcs on
To turn off CRC stripping, first VLAN stripping must be disabled:
#ethtool -K <interface> rx-vlan-offload off
if any VLAN interfaces exists, otherwise VLAN stripping will be turned
off by the driver.
In iavf_configure_queues add check if CRC stripping is enabled for
VF, if it's enabled then set crc_disabled to false on every VF's
queue. In iavf_set_features add check if CRC stripping setting was
changed then schedule reset.
Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently when configuring promiscuous mode on the AVF we detect a
change in the netdev->flags. We use IFF_PROMISC and IFF_ALLMULTI to
determine whether or not we need to request/release promiscuous mode
and/or multicast promiscuous mode. The problem is that the AQ calls for
setting/clearing promiscuous/multicast mode are treated separately. This
leads to a case where we can trigger two promiscuous mode AQ calls in
a row with the incorrect state. To fix this make a few changes.
Use IAVF_FLAG_AQ_CONFIGURE_PROMISC_MODE instead of the previous
IAVF_FLAG_AQ_[REQUEST|RELEASE]_[PROMISC|ALLMULTI] flags.
In iavf_set_rx_mode() detect if there is a change in the
netdev->flags in comparison with adapter->flags and set the
IAVF_FLAG_AQ_CONFIGURE_PROMISC_MODE aq_required bit. Then in
iavf_process_aq_command() only check for IAVF_FLAG_CONFIGURE_PROMISC_MODE
and call iavf_set_promiscuous() if it's set.
In iavf_set_promiscuous() check again to see which (if any) promiscuous
mode bits have changed when comparing the netdev->flags with the
adapter->flags. Use this to set the flags which get sent to the PF
driver.
Add a spinlock that is used for updating current_netdev_promisc_flags
and only allows one promiscuous mode AQ at a time.
[1] Fixes the fact that we will only have one AQ call in the aq_required
queue at any one time.
[2] Streamlines the change in promiscuous mode to only set one AQ
required bit.
[3] This allows us to keep track of the current state of the flags and
also makes it so we can take the most recent netdev->flags promiscuous
mode state.
[4] This fixes the problem where a change in the netdev->flags can cause
IAVF_FLAG_AQ_CONFIGURE_PROMISC_MODE to be set in iavf_set_rx_mode(),
but cleared in iavf_set_promiscuous() before the change is ever made via
AQ call.
Fixes: 47d3483988 ("i40evf: Add driver support for promiscuous mode")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As 32bits of dissector->used_keys are exhausted,
increase the size to 64bits.
This is base change for ESP/AH flow dissector patch.
Please find patch and discussions at
https://lore.kernel.org/netdev/ZMDNjD46BvZ5zp5I@corigine.com/T/#t
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Tested-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In iavf_adminq_task(), if the function can't acquire the
adapter->crit_lock, it checks if the driver is removing. If so, it simply
exits without re-enabling the interrupt. This is done to ensure that the
task stops processing as soon as possible once the driver is being removed.
However, if the IAVF_FLAG_PF_COMMS_FAILED is set, the function checks this
before attempting to acquire the lock. In this case, the function exits
early and re-enables the interrupt. This will happen even if the driver is
already removing.
Avoid this, by moving the check to after the adapter->crit_lock is
acquired. This way, if the driver is removing, we will not re-enable the
interrupt.
Fixes: fc2e6b3b13 ("iavf: Rework mutexes for better synchronisation")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In iavf_adminq_task(), if kzalloc() fails to allocate the event.msg_buf,
the function will exit without releasing the adapter->crit_lock.
This is unlikely, but if it happens, the next access to that mutex will
deadlock.
Fix this by moving the unlock to the end of the function, and adding a new
label to allow jumping to the unlock portion of the function exit flow.
Fixes: fc2e6b3b13 ("iavf: Rework mutexes for better synchronisation")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The reset task is currently scheduled from the watchdog or adminq tasks.
First, all direct calls to schedule the reset task are replaced with the
iavf_schedule_reset(), which is modified to accept the flag showing the
type of reset.
To prevent the reset task from starting once iavf_remove() starts, we need
to check the __IAVF_IN_REMOVE_TASK bit before we schedule it. This is now
easily added to iavf_schedule_reset().
Finally, remove the check for IAVF_FLAG_RESET_NEEDED in the watchdog task.
It is redundant since all callers who set the flag immediately schedules
the reset task.
Fixes: 3ccd54ef44 ("iavf: Fix init state closure on remove")
Fixes: 14756b2ae2 ("iavf: Fix __IAVF_RESETTING state usage")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
A driver's lock (crit_lock) is used to serialize all the driver's tasks.
Lockdep, however, shows a circular dependency between rtnl and
crit_lock. This happens when an ndo that already holds the rtnl requests
the driver to reset, since the reset task (in some paths) tries to grab
rtnl to either change real number of queues of update netdev features.
[566.241851] ======================================================
[566.241893] WARNING: possible circular locking dependency detected
[566.241936] 6.2.14-100.fc36.x86_64+debug #1 Tainted: G OE
[566.241984] ------------------------------------------------------
[566.242025] repro.sh/2604 is trying to acquire lock:
[566.242061] ffff9280fc5ceee8 (&adapter->crit_lock){+.+.}-{3:3}, at: iavf_close+0x3c/0x240 [iavf]
[566.242167]
but task is already holding lock:
[566.242209] ffffffff9976d350 (rtnl_mutex){+.+.}-{3:3}, at: iavf_remove+0x6b5/0x730 [iavf]
[566.242300]
which lock already depends on the new lock.
[566.242353]
the existing dependency chain (in reverse order) is:
[566.242401]
-> #1 (rtnl_mutex){+.+.}-{3:3}:
[566.242451] __mutex_lock+0xc1/0xbb0
[566.242489] iavf_init_interrupt_scheme+0x179/0x440 [iavf]
[566.242560] iavf_watchdog_task+0x80b/0x1400 [iavf]
[566.242627] process_one_work+0x2b3/0x560
[566.242663] worker_thread+0x4f/0x3a0
[566.242696] kthread+0xf2/0x120
[566.242730] ret_from_fork+0x29/0x50
[566.242763]
-> #0 (&adapter->crit_lock){+.+.}-{3:3}:
[566.242815] __lock_acquire+0x15ff/0x22b0
[566.242869] lock_acquire+0xd2/0x2c0
[566.242901] __mutex_lock+0xc1/0xbb0
[566.242934] iavf_close+0x3c/0x240 [iavf]
[566.242997] __dev_close_many+0xac/0x120
[566.243036] dev_close_many+0x8b/0x140
[566.243071] unregister_netdevice_many_notify+0x165/0x7c0
[566.243116] unregister_netdevice_queue+0xd3/0x110
[566.243157] iavf_remove+0x6c1/0x730 [iavf]
[566.243217] pci_device_remove+0x33/0xa0
[566.243257] device_release_driver_internal+0x1bc/0x240
[566.243299] pci_stop_bus_device+0x6c/0x90
[566.243338] pci_stop_and_remove_bus_device+0xe/0x20
[566.243380] pci_iov_remove_virtfn+0xd1/0x130
[566.243417] sriov_disable+0x34/0xe0
[566.243448] ice_free_vfs+0x2da/0x330 [ice]
[566.244383] ice_sriov_configure+0x88/0xad0 [ice]
[566.245353] sriov_numvfs_store+0xde/0x1d0
[566.246156] kernfs_fop_write_iter+0x15e/0x210
[566.246921] vfs_write+0x288/0x530
[566.247671] ksys_write+0x74/0xf0
[566.248408] do_syscall_64+0x58/0x80
[566.249145] entry_SYSCALL_64_after_hwframe+0x72/0xdc
[566.249886]
other info that might help us debug this:
[566.252014] Possible unsafe locking scenario:
[566.253432] CPU0 CPU1
[566.254118] ---- ----
[566.254800] lock(rtnl_mutex);
[566.255514] lock(&adapter->crit_lock);
[566.256233] lock(rtnl_mutex);
[566.256897] lock(&adapter->crit_lock);
[566.257388]
*** DEADLOCK ***
The deadlock can be triggered by a script that is continuously resetting
the VF adapter while doing other operations requiring RTNL, e.g:
while :; do
ip link set $VF up
ethtool --set-channels $VF combined 2
ip link set $VF down
ip link set $VF up
ethtool --set-channels $VF combined 4
ip link set $VF down
done
Any operation that triggers a reset can substitute "ethtool --set-channles"
As a fix, add a new task "finish_config" that do all the work which
needs rtnl lock. With the exception of iavf_remove(), all work that
require rtnl should be called from this task.
As for iavf_remove(), at the point where we need to call
unregister_netdevice() (and grab rtnl_lock), we make sure the finish_config
task is not running (cancel_work_sync()) to safely grab rtnl. Subsequent
finish_config work cannot restart after that since the task is guarded
by the __IAVF_IN_REMOVE_TASK bit in iavf_schedule_finish_config().
Fixes: 5ac49f3c27 ("iavf: use mutexes for locking of critical sections")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This reverts commit 08f1c147b7.
Netdev is no longer being detached during reset, so this fix can be
reverted. We leave the removal of "hacky" IFF_UP flag update.
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This reverts commit aa626da947.
Detaching device during reset was not fully fixing the rtnl locking issue,
as there could be a situation where callback was already in progress before
detaching netdev.
Furthermore, detaching netdevice causes TX timeouts if traffic is running.
To reproduce:
ip netns exec ns1 iperf3 -c $PEER_IP -t 600 --logfile /dev/null &
while :; do
for i in 200 7000 400 5000 300 3000 ; do
ip netns exec ns1 ip link set $VF1 mtu $i
sleep 2
done
sleep 10
done
Currently, callbacks such as iavf_change_mtu() wait for the reset.
If the reset fails to acquire the rtnl_lock, they schedule the netdev
update for later while continuing the reset flow. Operations like MTU
changes are performed under the rtnl_lock. Therefore, when the operation
finishes, another callback that uses rtnl_lock can start.
Signed-off-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There was a fail when trying to add the interface to bonding
right after changing the MTU on the interface. It was caused
by bonding interface unable to open the interface due to
interface being in __RESETTING state because of MTU change.
Add new reset_waitqueue to indicate that reset has finished.
Add waiting for reset to finish in callbacks which trigger hw reset:
iavf_set_priv_flags(), iavf_change_mtu() and iavf_set_ringparam().
We use a 5000ms timeout period because on Hyper-V based systems,
this operation takes around 3000-4000ms. In normal circumstances,
it doesn't take more than 500ms to complete.
Add a function iavf_wait_for_reset() to reuse waiting for reset code and
use it also in iavf_set_channels(), which already waits for reset.
We don't use error handling in iavf_set_channels() as this could
cause the device to be in incorrect state if the reset was scheduled
but hit timeout or the waitng function was interrupted by a signal.
Fixes: 4e5e6b5d9d ("iavf: Fix return of set the new channel count")
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Co-developed-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If the system tries to close the netdev while iavf_reset_task() is
running, __LINK_STATE_START will be cleared and netif_running() will
return false in iavf_reinit_interrupt_scheme(). This will result in
iavf_free_traffic_irqs() not being called and a leak as follows:
[7632.489326] remove_proc_entry: removing non-empty directory 'irq/999', leaking at least 'iavf-enp24s0f0v0-TxRx-0'
[7632.490214] WARNING: CPU: 0 PID: 10 at fs/proc/generic.c:718 remove_proc_entry+0x19b/0x1b0
is shown when pci_disable_msix() is later called. Fix by using the
internal adapter state. The traffic IRQs will always exist if
state == __IAVF_RUNNING.
Fixes: 5b36e8d04b ("i40evf: Enable VF to request an alternate queue allocation")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Make all possible functions static.
Move iavf_force_wb() up to avoid forward declaration.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Defer removal of current primary MAC until a replacement is successfully
added. Previous implementation would left filter list with no primary MAC.
This was found while reading the code.
The patch takes advantage of the fact that there can only be a single primary
MAC filter at any time ([1] by Piotr)
Piotr has also applied some review suggestions during our internal patch
submittal process.
[1] https://lore.kernel.org/netdev/20230614145302.902301-2-piotrx.gardocki@intel.com/
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Enable more than 32 IRQs by removing the u32 bit mask in
iavf_irq_enable_queues(). There is no need for the mask as there are no
callers that select individual IRQs through the bitmask. Also, if the PF
allocates more than 32 IRQs, this mask will prevent us from using all of
them.
Modify the comment in iavf_register.h to show that the maximum number
allowed for the IRQ index is 63 as per the iAVF standard 1.0 [1].
link: [1] https://www.intel.com/content/dam/www/public/us/en/documents/product-specifications/ethernet-adaptive-virtual-function-hardware-spec.pdf
Fixes: 5eae00c57f ("i40evf: main driver core")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230608200226.451861-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VLAN filters info is currently being held in a list and 2 bitmaps
(active_cvlans and active_svlans). We are experiencing some racing where
data is not in sync in the list and bitmaps. For example, the VLAN is
initially added to the list but only when the PF replies, it is added to
the bitmap. If a user adds many V2 VLANS before the PF responds:
while [ $((i++)) ]
ip l add l eth0 name eth0.$i type vlan id $i
we might end up with more VLAN list entries than the designated limit.
Also, The "ip link show" will show more links added than the PF limit.
On the other and, the bitmaps are only used to check the number of VLAN
filters and to re-enable the filters when the interface goes from DOWN to
UP.
This patch gets rid of the bitmaps and uses the list only. To do that,
the states of the VLAN filter are modified:
1 - IAVF_VLAN_REMOVE: the entry needs to be totally removed after informing
the PF. This is the "ip link del eth0.$i" path.
2 - IAVF_VLAN_DISABLE: (new) the netdev went down. The filter needs to be
removed from the PF and then marked INACTIVE.
3 - IAVF_VLAN_INACTIVE: (new) no PF filter exists, but the user did not
delete the VLAN.
Fixes: 48ccc43ecf ("iavf: Add support VIRTCHNL_VF_OFFLOAD_VLAN_V2 during netdev config")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The VLAN filter states are currently being saved as individual bits.
This is error prone as multiple bits might be mistakenly set.
Fix by replacing the bits with a single state enum. Also, add an
"ACTIVE" state for filters that are accepted by the PF.
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When a system with E810 with existing VFs gets rebooted the following
hang may be observed.
Pid 1 is hung in iavf_remove(), part of a network driver:
PID: 1 TASK: ffff965400e5a340 CPU: 24 COMMAND: "systemd-shutdow"
#0 [ffffaad04005fa50] __schedule at ffffffff8b3239cb
#1 [ffffaad04005fae8] schedule at ffffffff8b323e2d
#2 [ffffaad04005fb00] schedule_hrtimeout_range_clock at ffffffff8b32cebc
#3 [ffffaad04005fb80] usleep_range_state at ffffffff8b32c930
#4 [ffffaad04005fbb0] iavf_remove at ffffffffc12b9b4c [iavf]
#5 [ffffaad04005fbf0] pci_device_remove at ffffffff8add7513
#6 [ffffaad04005fc10] device_release_driver_internal at ffffffff8af08baa
#7 [ffffaad04005fc40] pci_stop_bus_device at ffffffff8adcc5fc
#8 [ffffaad04005fc60] pci_stop_and_remove_bus_device at ffffffff8adcc81e
#9 [ffffaad04005fc70] pci_iov_remove_virtfn at ffffffff8adf9429
#10 [ffffaad04005fca8] sriov_disable at ffffffff8adf98e4
#11 [ffffaad04005fcc8] ice_free_vfs at ffffffffc04bb2c8 [ice]
#12 [ffffaad04005fd10] ice_remove at ffffffffc04778fe [ice]
#13 [ffffaad04005fd38] ice_shutdown at ffffffffc0477946 [ice]
#14 [ffffaad04005fd50] pci_device_shutdown at ffffffff8add58f1
#15 [ffffaad04005fd70] device_shutdown at ffffffff8af05386
#16 [ffffaad04005fd98] kernel_restart at ffffffff8a92a870
#17 [ffffaad04005fda8] __do_sys_reboot at ffffffff8a92abd6
#18 [ffffaad04005fee0] do_syscall_64 at ffffffff8b317159
#19 [ffffaad04005ff08] __context_tracking_enter at ffffffff8b31b6fc
#20 [ffffaad04005ff18] syscall_exit_to_user_mode at ffffffff8b31b50d
#21 [ffffaad04005ff28] do_syscall_64 at ffffffff8b317169
#22 [ffffaad04005ff50] entry_SYSCALL_64_after_hwframe at ffffffff8b40009b
RIP: 00007f1baa5c13d7 RSP: 00007fffbcc55a98 RFLAGS: 00000202
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f1baa5c13d7
RDX: 0000000001234567 RSI: 0000000028121969 RDI: 00000000fee1dead
RBP: 00007fffbcc55ca0 R8: 0000000000000000 R9: 00007fffbcc54e90
R10: 00007fffbcc55050 R11: 0000000000000202 R12: 0000000000000005
R13: 0000000000000000 R14: 00007fffbcc55af0 R15: 0000000000000000
ORIG_RAX: 00000000000000a9 CS: 0033 SS: 002b
During reboot all drivers PM shutdown callbacks are invoked.
In iavf_shutdown() the adapter state is changed to __IAVF_REMOVE.
In ice_shutdown() the call chain above is executed, which at some point
calls iavf_remove(). However iavf_remove() expects the VF to be in one
of the states __IAVF_RUNNING, __IAVF_DOWN or __IAVF_INIT_FAILED. If
that's not the case it sleeps forever.
So if iavf_shutdown() gets invoked before iavf_remove() the system will
hang indefinitely because the adapter is already in state __IAVF_REMOVE.
Fix this by returning from iavf_remove() if the state is __IAVF_REMOVE,
as we already went through iavf_shutdown().
Fixes: 974578017f ("iavf: Add waiting so the port is initialized in remove")
Fixes: a8417330f8 ("iavf: Fix race condition between iavf_shutdown and iavf_remove")
Reported-by: Marius Cornea <mcornea@redhat.com>
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When an interface with the maximum number of VLAN filters is brought up,
a spurious error is logged:
[257.483082] 8021q: adding VLAN 0 to HW filter on device enp0s3
[257.483094] iavf 0000:00:03.0 enp0s3: Max allowed VLAN filters 8. Remove existing VLANs or disable filtering via Ethtool if supported.
The VF driver complains that it cannot add the VLAN 0 filter.
On the other hand, the PF driver always adds VLAN 0 filter on VF
initialization. The VF does not need to ask the PF for that filter at
all.
Fix the error by not tracking VLAN 0 filters altogether. With that, the
check added by commit 0e710a3ffd ("iavf: Fix VF driver counting VLAN 0
filters") in iavf_virtchnl.c is useless and might be confusing if left as
it suggests that we track VLAN 0.
Fixes: 0e710a3ffd ("iavf: Fix VF driver counting VLAN 0 filters")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this doesn't control interrupt generation by the Root Port; that
is controlled by the AER Root Error Command register, which is managed by
the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Since the latest Intel hardware does both IWARP and ROCE, rename the
term IWARP in the virtchnl header to be RDMA. Do this for both upper and
lower case instances. Many of the non-virtchnl.h changes were done with
regular expression replacements using perl like:
perl -p -i -e 's/_IWARP/_RDMA/' <files>
perl -p -i -e 's/_iwarp/_rdma/' <files>
and I had to pick up a few instances manually.
The virtchnl.h header has some comments and clarity added around when to
use certain defines.
note: had to fix a checkpatch warning for a long line by wrapping one of
the lines I changed.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jakub Andrysiak <jakub.andrysiak@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
iavf_replace_primary_mac() utilizes queue_work() to schedule the
watchdog task but that only ensures that the watchdog task is queued
to run. To make sure the watchdog is executed asap use
mod_delayed_work().
Without this patch it may take up to 2s until the watchdog task gets
executed, which may cause long delays when setting the MAC address.
Fixes: a3e839d539 ("iavf: Add usage of new virtchnl format to set default MAC")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove netdev_update_features() from iavf_adminq_task(), as it can cause
deadlocks due to needing rtnl_lock. Instead use the
IAVF_FLAG_SETUP_NETDEV_FEATURES flag to indicate that netdev features need
to be updated in the watchdog task. iavf_set_vlan_offload_features()
and iavf_set_queue_vlan_tag_loc() can be called directly from
iavf_virtchnl_completion().
Suggested-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We are seeing an issue where setting the MAC address on iavf fails with
EAGAIN after the 2.5s timeout expires in iavf_set_mac().
There is the following deadlock scenario:
iavf_set_mac(), holding rtnl_lock, waits on:
iavf_watchdog_task (within iavf_wq) to send a message to the PF,
and
iavf_adminq_task (within iavf_wq) to receive a response from the PF.
In this adapter state (>=__IAVF_DOWN), these tasks do not need to take
rtnl_lock, but iavf_wq is a global single-threaded workqueue, so they
may get stuck waiting for another adapter's iavf_watchdog_task to run
iavf_init_config_adapter(), which does take rtnl_lock.
The deadlock resolves itself by the timeout in iavf_set_mac(),
which results in EAGAIN returned to userspace.
Let's break the deadlock loop by changing iavf_wq into a per-adapter
workqueue, so that one adapter's tasks are not blocked by another's.
Fixes: 35a2443d09 ("iavf: Add waiting for response from PF in set mac")
Co-developed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This fixes a copy-paste issue where dev_err would log the dst mask even
though it is clearly talking about src.
Found by Linux Verification Center (linuxtesting.org) with the SVACE
static analysis tool.
Fixes: 0075fa0fad ("i40evf: Add support to apply cloud filters")
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The iavf_init_module() won't destroy workqueue when pci_register_driver()
failed. Call destroy_workqueue() when pci_register_driver() failed to
prevent the resource leak.
Similar to the handling of u132_hcd_init in commit f276e00279
("usb: u132-hcd: fix resource leak")
Fixes: 2803b16c10 ("i40e/i40evf: Use private workqueue")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix a deadlock introduced by commit
974578017f ("iavf: Add waiting so the port is initialized in remove")
due to race condition between iavf_shutdown and iavf_remove, where
iavf_remove stucks forever in while loop since iavf_shutdown already
set __IAVF_REMOVE adapter state.
Fix this by checking if the __IAVF_IN_REMOVE_TASK has already been
set and return if so.
Fixes: 974578017f ("iavf: Add waiting so the port is initialized in remove")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
IAVF_FLAG_INITIAL_MAC_SET prevents waiting on iavf_is_mac_set_handled()
the first time the MAC is set. This breaks gratuitous ARP because the
MAC address has not been updated yet when the gARP packet is sent out.
Current behaviour:
$ echo 1 > /sys/class/net/ens4f0/device/sriov_numvfs
iavf 0000:88:02.0: MAC address: ee:04:19:14:ec:ea
$ ip addr add 192.168.1.1/24 dev ens4f0v0
$ ip link set dev ens4f0v0 up
$ echo 1 > /proc/sys/net/ipv4/conf/ens4f0v0/arp_notify
$ ip link set ens4f0v0 addr 00:11:22:33:44:55
07:23:41.676611 ee:04:19:14:ec:ea > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Request who-has 192.168.1.1 tell 192.168.1.1, length 28
With IAVF_FLAG_INITIAL_MAC_SET removed:
$ echo 1 > /sys/class/net/ens4f0/device/sriov_numvfs
iavf 0000:88:02.0: MAC address: 3e:8a:16:a2:37:6d
$ ip addr add 192.168.1.1/24 dev ens4f0v0
$ ip link set dev ens4f0v0 up
$ echo 1 > /proc/sys/net/ipv4/conf/ens4f0v0/arp_notify
$ ip link set ens4f0v0 addr 00:11:22:33:44:55
07:28:01.836608 00:11:22:33:44:55 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Request who-has 192.168.1.1 tell 192.168.1.1, length 28
Fixes: 35a2443d09 ("iavf: Add waiting for response from PF in set mac")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Changed information about device removal in dmesg.
In function iavf_remove changed printed message from
"Remove" to "Removing" after hot vf plug/unplug.
Reason for this change is that, that "Removing" word
is better because it is clearer for the user that
the device is already being removed rather than implying
that the user should remove this device.
Signed-off-by: Bartosz Staszewski <bartoszx.staszewski@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
__FUNCTION__ exists only for backwards compatibility reasons with old
gcc versions. Replace it with __func__.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously changing mac address gives false negative because
ip link set <interface> address <MAC> return with
RTNLINK: Permission denied.
In iavf_set_mac was check if PF handled our mac set request,
even before filter was added to list.
Because this check returns always true and it never waits for
PF's response.
Move iavf_is_mac_handled to wait_event_interruptible_timeout
instead of false. Now it will wait for PF's response and then
check if address was added or rejected.
Fixes: 35a2443d09 ("iavf: Add waiting for response from PF in set mac")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Co-developed-by: Norbert Zulinski <norbertx.zulinski@intel.com>
Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
During stress tests with adding VF to namespace and changing vf's
trust there was a race between iavf_reset_task and iavf_close.
Sometimes when IAVF_FLAG_AQ_DISABLE_QUEUES from iavf_close was sent
to PF after reset and before IAVF_AQ_GET_CONFIG was sent then PF
returns error IAVF_NOT_SUPPORTED to disable queues request and
following requests. There is need to get_config before other
aq_required will be send but iavf_close clears all flags, if
get_config was not sent before iavf_close, then it will not be send
at all.
In case when IAVF_FLAG_AQ_GET_OFFLOAD_VLAN_V2_CAPS was sent before
IAVF_FLAG_AQ_DISABLE_QUEUES then there was rtnl_lock deadlock
between iavf_close and iavf_adminq_task until iavf_close timeouts
and disable queues was sent after iavf_close ends.
There was also a problem with sending delete/add filters.
Sometimes when filters was not yet added to PF and in
iavf_close all filters was set to remove there might be a try
to remove nonexistent filters on PF.
Add aq_required_tmp to save aq_required flags and send them after
disable_queues will be handled. Clear flags given to iavf_down
different than IAVF_FLAG_AQ_GET_CONFIG as this flag is necessary
to sent other aq_required. Remove some flags that we don't
want to send as we are in iavf_close and we want to disable
interface. Remove filters which was not yet sent and send del
filters flags only when there are filters to remove.
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
iavf_reset_task() takes crit_lock at the beginning and holds
it during whole call. The function subsequently calls
iavf_init_interrupt_scheme() that grabs RTNL. Problem occurs
when userspace initiates during the reset task any ndo callback
that runs under RTNL like iavf_open() because some of that
functions tries to take crit_lock. This leads to classic A-B B-A
deadlock scenario.
To resolve this situation the device should be detached in
iavf_reset_task() prior taking crit_lock to avoid subsequent
ndos running under RTNL and reattach the device at the end.
Fixes: 62fe2a865e ("i40evf: add missing rtnl_lock() around i40evf_set_interrupt_capability")
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Patryk Piotrowski <patryk.piotrowski@intel.com>
Cc: SlawomirX Laba <slawomirx.laba@intel.com>
Tested-by: Vitaly Grinberg <vgrinber@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix deadlock that occurs when iavf interface is a part of failover
configuration.
1. Mutex crit_lock is taken at the beginning of iavf_watchdog_task()
2. Function iavf_init_config_adapter() is called when adapter
state is __IAVF_INIT_CONFIG_ADAPTER
3. iavf_init_config_adapter() calls register_netdevice() that emits
NETDEV_REGISTER event
4. Notifier function failover_event() then calls
net_failover_slave_register() that calls dev_open()
5. dev_open() calls iavf_open() that tries to take crit_lock in
end-less loop
Stack trace:
...
[ 790.251876] usleep_range_state+0x5b/0x80
[ 790.252547] iavf_open+0x37/0x1d0 [iavf]
[ 790.253139] __dev_open+0xcd/0x160
[ 790.253699] dev_open+0x47/0x90
[ 790.254323] net_failover_slave_register+0x122/0x220 [net_failover]
[ 790.255213] failover_slave_register.part.7+0xd2/0x180 [failover]
[ 790.256050] failover_event+0x122/0x1ab [failover]
[ 790.256821] notifier_call_chain+0x47/0x70
[ 790.257510] register_netdevice+0x20f/0x550
[ 790.258263] iavf_watchdog_task+0x7c8/0xea0 [iavf]
[ 790.259009] process_one_work+0x1a7/0x360
[ 790.259705] worker_thread+0x30/0x390
To fix the situation we should check the current adapter state after
first unsuccessful mutex_trylock() and return with -EBUSY if it is
__IAVF_INIT_CONFIG_ADAPTER.
Fixes: 226d528512 ("iavf: fix locking of critical sections")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
