Marek reports that a deadlock occurs with the AX88772A PHY used on the
ASIX USB network driver:
asix 1-1.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:003:10] driver [Asix Electronics AX88772A] (irq=POLL)
Asix Electronics AX88772A usb-001:003:10: attached PHY driver(mii_bus:phy_addr=usb-001:003:10, irq=POLL)
asix 1-1.4:1.0 eth0: register 'asix' at usb-12110000.usb-1.4, ASIX AX88772 USB 2.0 Ethernet, a2:99:b6💿11:eb
asix 1-1.4:1.0 eth0: configuring for phy/internal link mode
============================================
WARNING: possible recursive locking detected
6.6.0-rc1-00239-g8da77df649c4-dirty #13949 Not tainted
--------------------------------------------
kworker/3:3/71 is trying to acquire lock:
c6c704cc (&dev->lock){+.+.}-{3:3}, at: phy_start_aneg+0x1c/0x38
but task is already holding lock:
c6c704cc (&dev->lock){+.+.}-{3:3}, at: phy_state_machine+0x100/0x2b8
This is because we now consistently call phy_process_state_change()
while holding phydev->lock, but the AX88772A PHY driver then goes on
to call phy_start_aneg() which tries to grab the same lock - causing
deadlock.
Fix this by exporting the unlocked version, and use this in the PHY
driver instead.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: ef113a60d0 ("net: phy: call phy_error_precise() while holding the lock")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1qiEFs-007g7b-Lq@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Convert phy_stop() to use the new locked-section and unlocked-section
parts of the PHY state machine.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split out the locked and unlocked sections of phy_state_machine() into
two separate functions which can be called inside the phydev lock and
outside the phydev lock as appropriate, thus allowing us to combine
the locked regions in the caller of phy_state_machine() with the
locked region inside phy_state_machine().
This avoids unnecessarily dropping the phydev lock which may allow
races to occur.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move phy_state_machine() before phy_stop() to avoid subsequent patches
introducing forward references.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the call to phy_suspend() to the end of phy_state_machine() after
we release the lock so that we can combine the locked areas.
phy_suspend() can not be called while holding phydev->lock as it has
caused deadlocks in the past.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the call to start auto-negotiation inside the lock in the PHYLIB
state machine, calling the locked variant _phy_start_aneg(). This
avoids unnecessarily releasing and re-acquiring the lock.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the locking out of phy_error_precise() and to its only call site,
merging with the locked region that has already been taken.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_stop() calls phy_process_state_change() while holding the phydev
lock, so also arrange for phy_state_machine() to do the same, so that
this function is called with consistent locking.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 91a7cda1f4 ("net: phy: Fix race condition on link status
change") all the phy_error() method invocations have been causing the
nested-mutex-lock deadlock because it's normally done in the PHY-driver
threaded IRQ handlers which since that change have been called with the
phydev->lock mutex held. Here is the calls thread:
IRQ: phy_interrupt()
+-> mutex_lock(&phydev->lock); <--------------------+
drv->handle_interrupt() | Deadlock due
+-> ERROR: phy_error() + to the nested
+-> phy_process_error() | mutex lock
+-> mutex_lock(&phydev->lock); <-+
phydev->state = PHY_ERROR;
mutex_unlock(&phydev->lock);
mutex_unlock(&phydev->lock);
The problem can be easily reproduced just by calling phy_error() from any
PHY-device threaded interrupt handler. Fix it by dropping the phydev->lock
mutex lock from the phy_process_error() method and printing a nasty error
message to the system log if the mutex isn't held in the caller execution
context.
Note for the fix to work correctly in the PHY-subsystem itself the
phydev->lock mutex locking must be added to the phy_error_precise()
function.
Link: https://lore.kernel.org/netdev/20230816180944.19262-1-fancer.lancer@gmail.com
Fixes: 91a7cda1f4 ("net: phy: Fix race condition on link status change")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/core/dev_ioctl.c (built-in code) will want to call phy_mii_ioctl()
for hardware timestamping purposes. This is not directly possible,
because phy_mii_ioctl() is a symbol provided under CONFIG_PHYLIB.
Do something similar to what was done in DSA in commit 5a17818682
("net: dsa: replace NETDEV_PRE_CHANGE_HWTSTAMP notifier with a stub"),
and arrange some indirect calls to phy_mii_ioctl() through a stub
structure containing function pointers, that's provided by phylib as
built-in even when CONFIG_PHYLIB=m, and which phy_init() populates at
runtime (module insertion).
Note: maybe the ownership of the ethtool_phy_ops singleton is backwards,
and the methods exposed by that should be later merged into phylib_stubs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230801142824.1772134-12-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When taking a network interface down (or removing a SFP module) after
the PHY has encountered an error, phy_stop() complains incorrectly
that it was called from HALTED state.
The reason this is incorrect is that the network driver will have
called phy_start() when the interface was brought up, and the fact
that the PHY has a problem bears no relationship to the administrative
state of the interface. Taking the interface administratively down
(which calls phy_stop()) is always the right thing to do after a
successful phy_start() call, whether or not the PHY has encountered
an error.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PHY library calls phy_error() something bad has happened, and
we halt the PHY state machine. Calling phy_error() from the main state
machine however is not precise enough to know whether the issue is
reading the link status or starting auto-negotiation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the phy_disconnect() -> phy_stop() path, we will be forcibly setting
the PHY state machine to PHY_HALTED. This invalidates the old_state !=
phydev->state condition in phy_state_machine() such that we will neither
display the state change for debugging, nor will we invoke the
link_change_notify() callback.
Factor the code by introducing phy_process_state_change(), and ensure
that we process the state change from phy_stop() as well.
Fixes: 5c5f626bca ("net: phy: improve handling link_change_notify callback")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phydev lock should be held while accessing members of phydev,
or calling into the driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All preparations are done. Now we can start using new functions and remove
the old code.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce code duplicated by migrating phy_init_eee() to
genphy_c45_eee_is_active().
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be needed for genphy_c45_ethtool_get_eee() provided
by next patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the required connection between netlink ethtool and
phylib to resolve PLCA get/set config and get status messages.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous attempt to augment carrier_down (see Link)
was not met with much enthusiasm so let's do the simple
thing of exposing what some devices already maintain.
Add a common ethtool statistic for link going down.
Currently users have to maintain per-driver mapping
to extract the right stat from the vendor-specific ethtool -S
stats. carrier_down does not fit the bill because it counts
a lot of software related false positives.
Add the statistic to the extended link state API to steer
vendors towards implementing all of it.
Implement for bnxt and all Linux-controlled PHYs. mlx5 and (possibly)
enic also have a counter for this but I leave the implementation
to their maintainers.
Link: https://lore.kernel.org/r/20220520004500.2250674-1-kuba@kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20221104190125.684910-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This adds support for rate matching (also known as rate adaptation) to
the phy subsystem. The general idea is that the phy interface runs at
one speed, and the MAC throttles the rate at which it sends packets to
the link speed. There's a good overview of several techniques for
achieving this at [1]. This patch adds support for three: pause-frame
based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and
2BASE-TL), and open-loop-based (such as in 10GBASE-W).
This patch makes a few assumptions and a few non assumptions about the
types of rate matching available. First, it assumes that different phys
may use different forms of rate matching. Second, it assumes that phys
can use rate matching for any of their supported link speeds (e.g. if a
phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T).
Third, it does not assume that all interface modes will use the same
form of rate matching. Fourth, it does not assume that all phy devices
will support rate matching (even if some do). Relaxing or strengthening
these (non-)assumptions could result in a different API. For example, if
all interface modes were assumed to use the same form of rate matching,
then a bitmask of interface modes supportting rate matching would
suffice.
For some better visibility into the process, the current rate matching
mode is exposed as part of the ethtool ksettings. For the moment, only
read access is supported. I'm not sure what userspace might want to
configure yet (disable it altogether, disable just one mode, specify the
mode to use, etc.). For the moment, since only pause-based rate
adaptation support is added in the next few commits, rate matching can
be disabled altogether by adjusting the advertisement.
802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and
"rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls
this feature "rate adaptation". I chose "rate matching" because it is
shorter, and because Russell doesn't think "adaptation" is correct in this
context.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon system sleep, mdio_bus_phy_suspend() stops the phy_state_machine(),
but subsequent interrupts may retrigger it:
They may have been left enabled to facilitate wakeup and are not
quiesced until the ->suspend_noirq() phase. Unwanted interrupts may
hence occur between mdio_bus_phy_suspend() and dpm_suspend_noirq(),
as well as between dpm_resume_noirq() and mdio_bus_phy_resume().
Retriggering the phy_state_machine() through an interrupt is not only
undesirable for the reason given in mdio_bus_phy_suspend() (freezing it
midway with phydev->lock held), but also because the PHY may be
inaccessible after it's suspended: Accesses to USB-attached PHYs are
blocked once usb_suspend_both() clears the can_submit flag and PHYs on
PCI network cards may become inaccessible upon suspend as well.
Amend phy_interrupt() to avoid triggering the state machine if the PHY
is suspended. Signal wakeup instead if the attached net_device or its
parent has been configured as a wakeup source. (Those conditions are
identical to mdio_bus_phy_may_suspend().) Postpone handling of the
interrupt until the PHY has resumed.
Before stopping the phy_state_machine() in mdio_bus_phy_suspend(),
wait for a concurrent phy_interrupt() to run to completion. That is
necessary because phy_interrupt() may have checked the PHY's suspend
status before the system sleep transition commenced and it may thus
retrigger the state machine after it was stopped.
Likewise, after re-enabling interrupt handling in mdio_bus_phy_resume(),
wait for a concurrent phy_interrupt() to complete to ensure that
interrupts which it postponed are properly rerun.
The issue was exposed by commit 1ce8b37241 ("usbnet: smsc95xx: Forward
PHY interrupts to PHY driver to avoid polling"), but has existed since
forever.
Fixes: 541cd3ee00 ("phylib: Fix deadlock on resume")
Link: https://lore.kernel.org/netdev/a5315a8a-32c2-962f-f696-de9a26d30091@samsung.com/
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org # v2.6.33+
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/b7f386d04e9b5b0e2738f0125743e30676f309ef.1656410895.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This fixes the following error caused by a race condition between
phydev->adjust_link() and a MDIO transaction in the phy interrupt
handler. The issue was reproduced with the ethernet FEC driver and a
micrel KSZ9031 phy.
[ 146.195696] fec 2188000.ethernet eth0: MDIO read timeout
[ 146.201779] ------------[ cut here ]------------
[ 146.206671] WARNING: CPU: 0 PID: 571 at drivers/net/phy/phy.c:942 phy_error+0x24/0x6c
[ 146.214744] Modules linked in: bnep imx_vdoa imx_sdma evbug
[ 146.220640] CPU: 0 PID: 571 Comm: irq/128-2188000 Not tainted 5.18.0-rc3-00080-gd569e86915b7 #9
[ 146.229563] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 146.236257] unwind_backtrace from show_stack+0x10/0x14
[ 146.241640] show_stack from dump_stack_lvl+0x58/0x70
[ 146.246841] dump_stack_lvl from __warn+0xb4/0x24c
[ 146.251772] __warn from warn_slowpath_fmt+0x5c/0xd4
[ 146.256873] warn_slowpath_fmt from phy_error+0x24/0x6c
[ 146.262249] phy_error from kszphy_handle_interrupt+0x40/0x48
[ 146.268159] kszphy_handle_interrupt from irq_thread_fn+0x1c/0x78
[ 146.274417] irq_thread_fn from irq_thread+0xf0/0x1dc
[ 146.279605] irq_thread from kthread+0xe4/0x104
[ 146.284267] kthread from ret_from_fork+0x14/0x28
[ 146.289164] Exception stack(0xe6fa1fb0 to 0xe6fa1ff8)
[ 146.294448] 1fa0: 00000000 00000000 00000000 00000000
[ 146.302842] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 146.311281] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 146.318262] irq event stamp: 12325
[ 146.321780] hardirqs last enabled at (12333): [<c01984c4>] __up_console_sem+0x50/0x60
[ 146.330013] hardirqs last disabled at (12342): [<c01984b0>] __up_console_sem+0x3c/0x60
[ 146.338259] softirqs last enabled at (12324): [<c01017f0>] __do_softirq+0x2c0/0x624
[ 146.346311] softirqs last disabled at (12319): [<c01300ac>] __irq_exit_rcu+0x138/0x178
[ 146.354447] ---[ end trace 0000000000000000 ]---
With the FEC driver phydev->adjust_link() calls fec_enet_adjust_link()
calls fec_stop()/fec_restart() and both these function reset and
temporary disable the FEC disrupting any MII transaction that
could be happening at the same time.
fec_enet_adjust_link() and phy_read() can be running at the same time
when we have one additional interrupt before the phy_state_machine() is
able to terminate.
Thread 1 (phylib WQ) | Thread 2 (phy interrupt)
|
| phy_interrupt() <-- PHY IRQ
| handle_interrupt()
| phy_read()
| phy_trigger_machine()
| --> schedule phylib WQ
|
|
phy_state_machine() |
phy_check_link_status() |
phy_link_change() |
phydev->adjust_link() |
fec_enet_adjust_link() |
--> FEC reset | phy_interrupt() <-- PHY IRQ
| phy_read()
|
Fix this by acquiring the phydev lock in phy_interrupt().
Link: https://lore.kernel.org/all/20220422152612.GA510015@francesco-nb.int.toradex.com/
Fixes: c974bdbc3e ("net: phy: Use threaded IRQ, to allow IRQ from sleeping devices")
cc: <stable@vger.kernel.org>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220506060815.327382-1-francesco.dolcini@toradex.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stop using the helpers to construct a special phy address which
indicates C45. Instead use the C45 accessors, which will call the
busses C45 specific read/write API.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As reported by Zhang there's a small issue if in forced mode the duplex
mode changes with the link staying up [0]. In this case the MAC isn't
notified about the change.
The proposed patch relies on the phylib state machine and ignores the
fact that there are drivers that uses phylib but not the phylib state
machine. So let's don't change the behavior for such drivers and fix
it w/o re-adding state PHY_FORCING for the case that phylib state
machine is used.
[0] https://lore.kernel.org/netdev/a5c26ffd-4ee4-a5e6-4103-873208ce0dc5@huawei.com/T/
Fixes: 2bd229df5e ("net: phy: remove state PHY_FORCING")
Reported-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Tested-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/7b8b9456-a93f-abbc-1dc5-a2c2542f932c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a race condition where the PHY state machine can change
members of the phydev structure at the same time userspace requests a
change via ethtool. To prevent this, have phy_ethtool_ksettings_set
take the PHY lock.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Reported-by: Walter Stoll <Walter.Stoll@duagon.com>
Suggested-by: Walter Stoll <Walter.Stoll@duagon.com>
Tested-by: Walter Stoll <Walter.Stoll@duagon.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split phy_start_aneg into a wrapper which takes the PHY lock, and a
helper doing the real work. This will be needed when
phy_ethtook_ksettings_set takes the lock.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows it to make use of a helper which assume the PHY is already
locked.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY structure should be locked while copying information out if
it, otherwise there is no guarantee of self consistency. Without the
lock the PHY state machine could be updating the structure.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following format issues:
1. open brace '{' following function definitions should go to the next
line.
2. braces {} are not necessary for single line statements.
3. else should follow close brace '}'.
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case phy_state_machine() works on top of USB device, we can get -ENODEV
at any point. So, be less noisy if device was removed.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of loopback, in most cases we need to disable autoneg support
and force some speed configuration. Otherwise, depending on currently
active auto negotiated link speed, the loopback may or may not work.
This patch was tested with following PHYs: TJA1102, KSZ8081, KSZ9031,
AT8035, AR9331.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If phy uses generic driver and autoneg is on, enter command
"ethtool -s eth0 speed 50" will not change phy speed actually, but
command "ethtool eth0" shows speed is 50Mb/s because phydev->speed
has been set to 50 and no update later.
And duplex setting has same problem too.
However, if autoneg is on, phy only changes speed and duplex according to
phydev->advertising, but not phydev->speed and phydev->duplex. So in this
case, phydev->speed and phydev->duplex don't need to be set in function
phy_ethtool_ksettings_set() if autoneg is on.
Fixes: 51e2a3846e ("PHY: Avoid unnecessary aneg restarts")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some internal PHY's have their events like link change reported by the
MAC interrupt. We have PHY_IGNORE_INTERRUPT to deal with this scenario.
I'm not too happy with this name. We don't ignore interrupts, typically
there is no interrupt exposed at a PHY level. So let's rename it to
PHY_MAC_INTERRUPT. This is in line with phy_mac_interrupt(), which is
called from the MAC interrupt handler to handle PHY events.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, PORT_MII is reported in the ethtool ops. This is odd
because it is an interface between the MAC and the PHY and no external
port. Some network card drivers will overwrite the port to twisted pair
or fiber, though. Even worse, the MDI/MDIX setting is only used by
ethtool if the port is twisted pair.
Set the port to PORT_TP by default because most PHY drivers are copper
ones. If there is fibre support and it is enabled, the PHY driver will
set it to PORT_FIBRE.
This will change reporting PORT_MII to either PORT_TP or PORT_FIBRE;
except for the genphy fallback driver.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to lockdep_assert_held(_once), similar to what is being done
in other subsystems. One advantage is that there's zero runtime
overhead if lockdep support isn't enabled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/ccc40b9d-8ee0-43a1-5009-2cc95ca79c85@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that all the PHY drivers have been migrated to directly implement
the generic .handle_interrupt() callback for a seamless support of
shared IRQs and all the .config_inter() implementations clear any
pending interrupts, we can safely remove the two callbacks.
With this patch, phylib has a proper support for shared IRQs (and not
just for multi-PHY devices. A PHY driver must implement both the
.handle_interrupt() and .config_intr() callbacks for the IRQs to be
actually used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some functions have different names between their prototypes
and the kernel-doc markup.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These functions are currently used by phy_interrupt() to either signal
an error condition or to trigger the link state machine. In an attempt
to actually support shared PHY IRQs, export these two functions so that
the actual PHY drivers can use them.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add kerneldoc for the core PHY data structures, a few inline functions
and exported functions which are not already documented.
v2
Typos
g/phy/PHY/s
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When phy_is_started() was added to catch incorrect PHY states,
phy_stop() would not be qualified against PHY_DOWN. It is possible to
reach that state when the PHY driver has been unbound and the network
device is then brought down.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have moved the PHY ethtool statistics to be dynamically
registered, we no longer need to inline those for ethtool. This used to
be done to avoid cross symbol referencing and allow ethtool to be
decoupled from PHYLIB entirely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We face an issue with rtl8211f, a pin is shared between INTB and PMEB,
and the PHY Register Accessible Interrupt is enabled by default, so
the INTB/PMEB pin is always active in polling mode case.
As Heiner pointed out "I was thinking about calling
phy_disable_interrupts() in phy_init_hw(), to have a defined init
state as we don't know in which state the PHY is if the PHY driver is
loaded. We shouldn't assume that it's the chip power-on defaults, BIOS
or boot loader could have changed this. Or in case of dual-boot
systems the other OS could leave the PHY in whatever state."
Make phy_disable_interrupts() non-static so that it could be used in
phy_init_hw() to have a defined init state.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the user to configure where on the cable the TDR data should be
retrieved, in terms of first and last sample, and the step between
samples. Also add the ability to ask for TDR data for just one pair.
If this configuration is not provided, it defaults to 1-150m at 1m
intervals for all pairs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Update nxp-tja11xx for API change.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a recurring pattern throughout some of the PHY code converting
a devad and regnum to our packed clause 45 representation. Rather than
having this scattered around the code, let's put a common translation
function in mdio.h, and provide some register accessors.
Convert the phylib core, phylink, bcm87xx and cortina to use these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
