The port is unused, but shares the same supply with port0, so fill the
DT property in. This fixes the following dtbs_check warning:
arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dt.yaml: usbphyc@5a006000: usb-phy@1: 'phy-supply' is a required property
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Use more specific custom GPIO line names which denote exactly where
the GPIO came from, i.e. the base board. Also, update the new blank
GPIO line names set up by stm32mp15xx-dhcom-som.dtsi back to their
original values.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
vdda1v1 and vdda1v8 supplies are required by USB PLL, not by the PHYs.
Remove them from usbphyc child phy nodes now that they are managed in
usbphyc parent node at SoC level.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Since GPIO_ACTIVE_HIGH is defined as 0, this change only increases the
correctness of the DT.
Fixes: fde180f06d ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The GPIO hog node name should match regex '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$',
make it so and fix the following two make dtbs_check warnings:
arch/arm/boot/dts/stm32mp157c-dhcom-picoitx.dt.yaml: hog-usb-port-power: $nodename:0: 'hog-usb-port-power' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'
arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dt.yaml: hog-usb-hub: $nodename:0: 'hog-usb-hub' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'
Fixes: ac68793f49 ("ARM: dts: stm32: Add DHCOM based PicoITX board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The DRC02 has no use for the on-SoM touchscreen controller, and the
on-SoM touchscreen controller may not even be populated, which then
results in error messages in kernel log. Disable the touchscreen
controller in DT.
Fixes: fde180f06d ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The uSD card detect signal on the DH DRC02 is active-high, with
a default pull down resistor on the board. Invert the polarity.
Fixes: fde180f06d ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
--
Note that this could not be tested on prototype SoMs, now that it is
tested, this issue surfaced, so it needs to be fixed.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add DT for DH DRC02 unit, which is a universal controller device.
The system has two ethernet ports, two CANs, RS485 and RS232, USB,
capacitive buttons and an OLED display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
