The driver neglects to check the result of platform_get_irq_optional()'s
call and blithely passes the negative error codes to devm_request_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL.
Stop calling devm_request_irq() with the invalid IRQ #s.
Fixes: 8562056f26 ("net: bcmgenet: request Wake-on-LAN interrupt")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 16nm internal EPHY that is present in 7712 is actually a 16nm
Gigabit PHY which has been forced to operate in 10/100 mode. Its
controls are therefore via the EXT_GPHY_CTRL registers and not via the
EXT_EPHY_CTRL which are used for all GENETv5 adapters. Add a match on
the 7712 compatible string to allow that differentiation to happen.
On previous GENETv4 chips the EXT_CFG_IDDQ_GLOBAL_PWR bit was cleared by
default, but this is not the case with this chip, so we need to make
sure we clear it to power on the EPHY.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new device_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.
@@
expression dev, np;
@@
- device_get_mac_address(np, dev->dev_addr, ETH_ALEN)
+ device_get_ethdev_address(np, dev)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers pass in ETH_ALEN and the function itself
will return -EINVAL for any other address length.
Just assume it's ETH_ALEN like all other mac address
helpers (nvm, of, platform).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fwnode_get_mac_address() and device_get_mac_address()
return a pointer to the buffer that was passed to them
on success or NULL on failure. None of the callers
care about the actual value, only if it's NULL or not.
These semantics differ from of_get_mac_address() which
returns an int so to avoid confusion make the device
helpers return an errno.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert Ethernet from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit extends the supported ethtool operations to allow MAC
level flow control to be configured for the bcmgenet driver.
The ethtool utility can be used to change the configuration of
auto-negotiated symmetric and asymmetric modes as well as manually
configuring support for RX and TX Pause frames individually.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY state machine has been fixed to only call the adjust_link
callback when the link state has changed. Therefore the old link
state variables are no longer needed to detect a change in link
state.
This commit effectively reverts
commit 5ad6e6c508 ("net: bcmgenet: improve bcmgenet_mii_setup()")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver has never used the netdev->{irq,base_addr,mem_start}
members, so this call is completely unnecessary.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that we disable each of the TX and RX queues in the TDMA and
RDMA control registers. This is a correctness change to be symmetrical
with the code that enables the TX and RX queues.
Tested-by: Maxime Ripard <maxime@cerno.tech>
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the EXT_ENERGY_DET_MASK bit allows the port energy detection
logic of the internal PHY to prevent the system from sleeping. Some
internal PHYs will report that energy is detected when the network
interface is closed which can prevent the system from going to sleep
if WoL is enabled when the interface is brought down.
Since the driver does not support waking the system on this logic,
this commit clears the bit whenever the internal PHY is powered up
and the other logic for manipulating the bit is removed since it
serves no useful function.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom UniMAC MDIO bus from mdio-bcm-unimac module comes too late.
So, GENET cannot find the ethernet PHY on UniMAC MDIO bus. This leads
GENET fail to attach the PHY as following log:
bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
...
could not attach to PHY
bcmgenet fd580000.ethernet eth0: failed to connect to PHY
uart-pl011 fe201000.serial: no DMA platform data
libphy: bcmgenet MII bus: probed
...
unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus
It is not just coming too late, there is also no way for the module
loader to figure out the dependency between GENET and its MDIO bus
driver unless we provide this MODULE_SOFTDEP hint.
This patch adds the soft dependency to load mdio-bcm-unimac module
before genet module to fix this issue.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=213485
Fixes: 9a4e796970 ("net: bcmgenet: utilize generic Broadcom UniMAC MDIO controller driver")
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the 'register_netdev()' call fails, we must undo a previous
'bcmgenet_mii_init()' call.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201212182005.120437-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
VALIDATE_MASK(eth_mask->h_source) is checked twice in a row in
bcmgenet_validate_flow(). Add VALIDATE_MASK(eth_mask->h_dest)
instead.
Fixes: 3e37095228 ("net: bcmgenet: add support for ethtool rxnfc flows")
Signed-off-by: Denis Efremov <efremov@linux.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver forgets to call clk_disable_unprepare() in error path after
a success calling for clk_prepare_enable().
Fix to goto err_clk_disable if clk_prepare_enable() is successful.
Fixes: c80d36ff63 ("net: bcmgenet: Use devm_clk_get_optional() to get the clocks")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver forgets to call clk_disable_unprepare() in error path after
a success calling for clk_prepare_enable().
Fix to goto err_clk_disable if clk_prepare_enable() is successful.
Fixes: 99d55638d4 ("net: bcmgenet: enable NETIF_F_HIGHDMA flag")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Hardware Filter Block RAM may not be preserved when the GENET
block is reset during a deep sleep, so it is not sufficient to
only backup and restore the enables.
This commit clears out the HFB block and reprograms the rxnfc
rules when the system resumes from a suspended state. To support
this the bcmgenet_hfb_create_rxnfc_filter() function is modified
to access the register space directly so that it can't fail due
to memory allocation issues.
Fixes: f50932cca6 ("net: bcmgenet: add WAKE_FILTER support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GENET driver interfaces with internal MoCA interface as well as
external MoCA chips like the BCM6802/6803 through a fixed link
interface. It is desirable for the mocad user-space daemon to be able to
control the carrier state based upon out of band messages that it
receives from the MoCA chip.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When commit 474ea9cafc ("net: bcmgenet: correctly pad short
packets") added the call to skb_padto() it should have been
located before the nr_frags parameter was read since that value
could be changed when padding packets with lengths between 55
and 59 bytes (inclusive).
The use of a stale nr_frags value can cause corruption of the
pad data when tx-scatter-gather is enabled. This corruption of
the pad can cause invalid checksum computation when hardware
offload of tx-checksum is also enabled.
Since the original reason for the padding was corrected by
commit 7dd399130e ("net: bcmgenet: fix skb_len in
bcmgenet_xmit_single()") we can remove the software padding all
together and make use of hardware padding of short frames as
long as the hardware also always appends the FCS value to the
frame.
Fixes: 474ea9cafc ("net: bcmgenet: correctly pad short packets")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 16-bit value that holds a short in network byte order should
be declared as a restricted big endian type to allow type checks
to succeed during assignment.
Fixes: 3e37095228 ("net: bcmgenet: add support for ethtool rxnfc flows")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function was originally removed by Baoyou Xie in
commit e2072600a2 ("net: bcmgenet: remove unused function in
bcmgenet.c") to prevent a build warning.
Some of the functions removed by Baoyou Xie are now used for
WAKE_FILTER support so his commit was reverted, but this function
is still unused and the kbuild test robot dutifully reported the
warning.
This commit once again removes the remaining unused hfb functions.
Fixes: 14da1510fe ("Revert "net: bcmgenet: remove unused function in bcmgenet.c"")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The side band interrupt service routine is not available on chips
like 7211, or rather, it does not permit the signaling of wake-up
events due to the complex interrupt hierarchy.
Move the wake-up event accounting into a .resume_noirq function,
account for possible wake-up events and clear the MPD/HFB interrupts
from there, while leaving the hardware untouched until the resume
function proceeds with doing its usual business.
Because bcmgenet_wol_power_down_cfg() now enables the MPD and HFB
interrupts, it is invoked by a .suspend_noirq function to prevent
the servicing of interrupts after the clocks have been disabled.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit enables support for the WAKE_FILTER method of Wake on
LAN for the GENET driver. The method can be enabled by adding 'f'
to the interface 'wol' setting specified by ethtool.
Rx network flow rules can be specified using ethtool. Rules that
define a flow-type with the RX_CLS_FLOW_WAKE action (i.e. -2) can
wake the system from the 'standby' power state when the WAKE_FILTER
WoL method is enabled.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit enables driver support for ethtool commands of this form:
ethtool -N|-U|--config-nfc|--config-ntuple devname
flow-type ether|ip4
[src xx:yy:zz:aa:bb:cc [m xx:yy:zz:aa:bb:cc]]
[dst xx:yy:zz:aa:bb:cc [m xx:yy:zz:aa:bb:cc]] [proto N [m N]]
[src-ip x.x.x.x [m x.x.x.x]] [dst-ip x.x.x.x [m x.x.x.x]] [tos N [m N]]
[l4proto N [m N]] [src-port N [m N]] [dst-port N [m N]] [spi N [m N]]
[l4data N [m N]] [vlan-etype N [m N]] [vlan N [m N]]
[dst-mac xx:yy:zz:aa:bb:cc [m xx:yy:zz:aa:bb:cc]] [action 0] [loc N] |
delete N
Since there is only one Rx Ring in this implementation action 0 behaves no
differently from not specifying a rule.
The rules can be seen with ethtool commands of this form:
ethtool -n|-u|--show-nfc|--show-ntuple devname [rule N]
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Hardware Filter Block code will be used by ethtool functions
when defining flow types so this commit moves the functions in the
file to prevent the need for prototype declarations.
This is broken out to facilitate review.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e2072600a2.
This commit restores the previous implementation of Hardware Filter
Block functions to the file for use in subsequent commits.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GENET_POWER_WOL_MAGIC power up and power down code configures
the device for WoL when suspending and disables the WoL logic when
resuming. It makes sense that this code should also manage the WoL
clocking.
This commit consolidates the logic and moves it earlier in the
resume sequence.
Since the clock is now only enabled if WoL is successfully entered
the wol_active flag is introduced to track that state to keep the
clock enables and disables balanced in case a suspend is aborted.
The MPD_EN hardware bit can't be used because it can be cleared
when the MAC is reset by a deep sleep.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit explicitly calls the bcmgenet_set_rx_mode() function when
the network interface is started. This function is normally called by
ndo_set_rx_mode when the flags are changed, but apparently not when
the driver is suspended and resumed.
This change ensures that address filtering or promiscuous mode are
properly restored by the driver after the MAC may have been reset.
Fixes: b6e978e504 ("net: bcmgenet: add suspend/resume callbacks")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is designed to drop Rx packets and reclaim the buffers
when an allocation fails, and the network interface needs to safely
handle this packet loss. Therefore, an allocation failure of Rx
SKBs is relatively benign.
However, the output of the warning message occurs with a high
scheduling priority that can cause excessive jitter/latency for
other high priority processing.
This commit suppresses the warning messages to prevent scheduling
problems while retaining the failure count in the statistics of
the network interface.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to track net_device_stats per ring to better support SMP
missed updating the rx_dropped member.
The ndo_get_stats method is also needed to combine the results for
ethtool statistics (-S) before filling in the ethtool structure.
Fixes: 37a30b435b ("net: bcmgenet: Track per TX/RX rings statistics")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to have parentheses around plain pointer variable or
negation operator. Drop them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's convenient to use get_unligned_beXX() and put_unaligned_beXX() helpers
to get or set MAC instead of open-coded variants.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conversion to devm_clk_get_optional() makes it explicit that clocks are
optional. This change allows to handle deferred probe in case clocks are
defined, but not yet probed. Due to above changes bail out in error case.
While here, check potential error when enable main clock.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing which needs a set of OF headers, followed by redundant
OF node ID check. Drop them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compiled with CONFIG_ACPI=n, ACPI_PTR() will be no-op, and thus
genet_acpi_match table defined, but not used. Compiler is not happy about
such data. Drop ACPI_PTR() for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware offloading of the NETIF_F_HW_CSUM and NETIF_F_RXCSUM
features requires the use of Transmit Status Blocks before transmit
frame data and Receive Status Blocks before receive frame data to
carry the checksum information.
Unfortunately, these status blocks are currently only enabled when
the NETIF_F_HW_CSUM feature is enabled. As a result NETIF_F_RXCSUM
will not actually be offloaded to the hardware unless both it and
NETIF_F_HW_CSUM are enabled. Fortunately, that is the default
configuration.
This commit addresses this issue by always enabling the use of
status blocks on both transmit and receive frames. Further, it
replaces the use of a dedicated flag within the driver private
data structure with direct use of the netdev features flags.
Fixes: 8101553978 ("net: bcmgenet: use CHECKSUM_COMPLETE for NETIF_F_RXCSUM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted in commit 28c2d1a7a0 ("net: bcmgenet: enable loopback
during UniMAC sw_reset") the UniMAC must be clocked at least 5
cycles while the sw_reset is asserted to ensure a clean reset.
That commit enabled local loopback to provide an Rx clock from the
GENET sourced Tx clk. However, when connected in MII mode the Tx
clk is sourced by the PHY so if an EPHY is not supplying clocks
(e.g. when the link is down) the UniMAC does not receive the
necessary clocks.
This commit extends the sw_reset window until the PHY reports that
the link is up thereby ensuring that the clocks are being provided
to the MAC to produce a clean reset.
One consequence is that if the system attempts to enter a Wake on
LAN suspend state when the PHY link has not been active the MAC
may not have had a chance to initialize cleanly. In this case, we
remove the sw_reset and enable the WoL reception path as normal
with the hope that the PHY will provide the necessary clocks to
drive the WoL blocks if the link becomes active after the system
has entered suspend.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3a55402c93.
This is not a good solution when connecting to an external switch
that may not support the isolation of the TXC signal resulting in
output driver contention on the pin.
A different solution is necessary.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject all unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use linux kernel version for ethtool and module versions.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If one types "failed to get enet clock" or similar into google
there are ~370k hits. The vast majority are people debugging
problems unrelated to this adapter, or bragging about their
rpi's. Further, the DT clock bindings here are optional.
Given that its not a fatal situation with common DT based
systems, lets reduce the severity so people aren't seeing failure
messages in everyday operation.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
