The BR_BCAST_FLOOD bridge port flag is now accepted by the driver and a
change in its state will determine a reconfiguration of the broadcast
egress flooding list on the FDB associated with the port.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring the learning state of a switch port.
When the user requests the HW learning to be disabled, a fast-age
procedure on that specific port is run so that previously learnt
addresses do not linger.
At device probe as well as on a bridge leave action, the ports are
configured with HW learning disabled since they are basically a
standalone port.
At the same time, at bridge join we inherit the bridge port BR_LEARNING
flag state and configure it on the switch port.
There were already some MC firmware ABI functions for changing the
learning state, but those were per FDB (bridging domain) and not per
port so we need to adjust those to use the new MC fw command which is
per port.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the code that determines the list of egress flood interfaces for
a specific flood type into a new function -
dpaa2_switch_fdb_get_flood_cfg().
This will help us to not duplicate code when the broadcast and
unknown ucast/mcast flooding domains will be individually configurable.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid a forward declaration in the next patches, move the
dpaa2_switch_fdb_set_egress_flood() function to the top of the file.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael reports that after the blamed patch, unbinding a VF would cause
these transactions to remain pending, and trigger some warnings with the
DMA API debug:
$ echo 1 > /sys/bus/pci/devices/0000\:00\:00.0/sriov_numvfs
pci 0000:00:01.0: [1957:ef00] type 00 class 0x020001
fsl_enetc_vf 0000:00:01.0: Adding to iommu group 19
fsl_enetc_vf 0000:00:01.0: enabling device (0000 -> 0002)
fsl_enetc_vf 0000:00:01.0 eno0vf0: renamed from eth0
$ echo 0 > /sys/bus/pci/devices/0000\:00\:00.0/sriov_numvfs
DMA-API: pci 0000:00:01.0: device driver has pending DMA allocations while released from device [count=1]
One of leaked entries details: [size=2048 bytes] [mapped with DMA_BIDIRECTIONAL] [mapped as coherent]
WARNING: CPU: 0 PID: 2547 at kernel/dma/debug.c:853 dma_debug_device_change+0x174/0x1c8
(...)
Call trace:
dma_debug_device_change+0x174/0x1c8
blocking_notifier_call_chain+0x74/0xa8
device_release_driver_internal+0x18c/0x1f0
device_release_driver+0x20/0x30
pci_stop_bus_device+0x8c/0xe8
pci_stop_and_remove_bus_device+0x20/0x38
pci_iov_remove_virtfn+0xb8/0x128
sriov_disable+0x3c/0x110
pci_disable_sriov+0x24/0x30
enetc_sriov_configure+0x4c/0x108
sriov_numvfs_store+0x11c/0x198
(...)
DMA-API: Mapped at:
dma_entry_alloc+0xa4/0x130
debug_dma_alloc_coherent+0xbc/0x138
dma_alloc_attrs+0xa4/0x108
enetc_setup_cbdr+0x4c/0x1d0
enetc_vf_probe+0x11c/0x250
pci 0000:00:01.0: Removing from iommu group 19
This happens because stupid me moved enetc_teardown_cbdr outside of
enetc_free_si_resources, but did not bother to keep calling
enetc_teardown_cbdr from all the places where enetc_free_si_resources
was called. In particular, now it is no longer called from the main
unbind function, just from the probe error path.
Fixes: 4b47c0b81f ("net: enetc: don't initialize unused ports from a separate code path")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to change the current ndo_xdp_xmit drop semantics because it will
allow us to implement better queue overflow handling. This is working
towards the larger goal of a XDP TX queue-hook. Move XDP_REDIRECT error
path handling from each XDP ethernet driver to devmap code. According to
the new APIs, the driver running the ndo_xdp_xmit pointer, will break tx
loop whenever the hw reports a tx error and it will just return to devmap
caller the number of successfully transmitted frames. It will be devmap
responsibility to free dropped frames.
Move each XDP ndo_xdp_xmit capable driver to the new APIs:
- veth
- virtio-net
- mvneta
- mvpp2
- socionext
- amazon ena
- bnxt
- freescale (dpaa2, dpaa)
- xen-frontend
- qede
- ice
- igb
- ixgbe
- i40e
- mlx5
- ti (cpsw, cpsw-new)
- tun
- sfc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/bpf/ed670de24f951cfd77590decf0229a0ad7fd12f6.1615201152.git.lorenzo@kernel.org
Running kernel-doc over the dpaa2-eth driver generates a bunch of
warnings. Fix them up by removing code comments for macros which are
self-explanatory, respecting the kdoc format for macro documentation and
other small changes like describing the expected return values of
functions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple ABI function declarations are split unnecessarry on multiple
lines. Fix this so that we have a consistent coding style.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum number of DPAA2 switch interfaces, including the control
interface, is 64. Even though this restriction existed from the first
place, the command structures which use an interface id bitmap were
poorly described and even though a single uint64_t is enough, all of
them used an array of 4 uint64_t's.
Fix this by reducing the size of the interface id field to a single
uint64_t.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Running kernel-doc over the dpaa2-switch driver generates a bunch of
warnings. Fix them up by removing code comments for macros which are
self-explanatory and adding a bit more context for the
dpsw_if_get_port_mac_addr() function and the fields of the
dpsw_vlan_if_cfg structure.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup the dpaa2-switch driver a bit by removing any unused MC firmware
ABI definitions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will allow users to configures packet-per-second policing
in the software datapath. In preparation for this, teach all drivers that
support offload of the policer action to reject such configuration as
currently none of them support it.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the dpaa2-switch driver has basic I/O capabilities on the
switch port net_devices and multiple bridging domains are supported,
move the driver out of staging.
The dpaa2-switch driver is placed right next to the dpaa2-eth driver
since, in the near future, they will be sharing most of the data path.
I didn't implement code reuse in this patch series because I wanted to
keep it as small as possible.
Also, the README is removed from staging with the intention to add
proper rst documentation afterwards to actually match was is supported
by the driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit fd5736bf9f ("enetc: Workaround for MDIO register access
issue"), enetc_refill_rx_ring no longer updates the RX BD ring's
consumer index, that is left to be done by the caller. This has led to
bugs such as the ones found in 96a5223b91 ("net: enetc: remove bogus
write to SIRXIDR from enetc_setup_rxbdr") and 3a5d12c9be ("net: enetc:
keep RX ring consumer index in sync with hardware"), so it is desirable
that we move back the update of the consumer index into enetc_refill_rx_ring.
The trouble with that is the different MDIO locking context for the two
callers of enetc_refill_rx_ring:
- enetc_clean_rx_ring runs under enetc_lock_mdio()
- enetc_setup_rxbdr runs outside enetc_lock_mdio()
Simplify the callers of enetc_refill_rx_ring by making enetc_setup_rxbdr
explicitly take enetc_lock_mdio() around the call. It will be the only
place in need of ensuring the hot accessors can be used.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no other reason why this forward declaration exists rather than
poor ordering of the functions.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the NAPI enetc_poll after enetc_clean_rx_ring such that
we can delete the forward declarations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The active_offloads variable of enetc_ndev_priv has an enum type, use it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we iterate through the BDs in the RX ring, the software producer
index (which is already passed by value to enetc_rxbd_next) lags behind,
and we end up with this funny looking "++i == rx_ring->bd_count" check
so that we drag it after us.
Let's pass the software producer index "i" by reference, so that
enetc_rxbd_next can increment it by itself (mod rx_ring->bd_count),
especially since enetc_rxbd_next has to increment the index anyway.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 3222b5b613 ("net: enetc: initialize RFS/RSS memories for
unused ports too") there is a requirement to initialize the memories of
unused PFs too, which has left the probe path in a bit of a rough shape,
because we basically have a minimal initialization path for unused PFs
which is separate from the main initialization path.
Now that initializing a control BD ring is as simple as calling
enetc_setup_cbdr, let's move that outside of enetc_alloc_si_resources
(unused PFs don't need classification rules, so no point in allocating
them just to free them later).
But enetc_alloc_si_resources is called both for PFs and for VFs, so now
that enetc_setup_cbdr is no longer called from this common function, it
means that the VF probe path needs to explicitly call enetc_setup_cbdr
too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It makes no sense from an API perspective to first initialize some
portion of struct enetc_cbdr outside enetc_setup_cbdr, then leave that
function to initialize the rest. enetc_setup_cbdr should be able to
perform all initialization given a zero-initialized struct enetc_cbdr.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All call sites call enetc_clear_cbdr and enetc_free_cbdr one after
another, so let's combine the two functions into a single method named
enetc_teardown_cbdr which does both, and in the same order.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enetc_clear_cbdr depends on struct enetc_hw because it must disable the
ring through a register write. We'd like to remove that dependency, so
let's do what's already done with the producer and consumer indices,
which is to save the iomem address in a variable kept in struct enetc_cbdr.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enetc_alloc_cbdr and enetc_setup_cbdr are always called one after
another, so we can simplify the callers and make enetc_setup_cbdr do
everything that's needed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't need to pass the struct device *dev to enetc CBDR APIs over
and over again, so save this inside struct enetc_cbdr::dma_dev and avoid
calling it from the enetc_free_cbdr functions.
This breaks the dependency of the cbdr API from struct enetc_si (the
station interface).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there is a dedicated file in this driver for interacting with
control BD rings, it makes sense to move these functions there.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in commit 29d98f54a4 ("net: enetc: allow hardware
timestamping on TX queues with tc-etf enabled"), hardware TX
timestamping requires an skb with skb->tstamp = 0. When a packet is sent
with SO_TXTIME, the skb->skb_mstamp_ns corrupts the value of skb->tstamp,
so the drivers need to explicitly reset skb->tstamp to zero after
consuming the TX time.
Create a helper named skb_txtime_consumed() which does just that. All
drivers which offload TC_SETUP_QDISC_ETF should implement it, and it
would make it easier to assess during review whether they do the right
thing in order to be compatible with hardware timestamping or not.
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The txtime is passed to the driver in skb->skb_mstamp_ns, which is
actually in a union with skb->tstamp (the place where software
timestamps are kept).
Since commit b50a5c70ff ("net: allow simultaneous SW and HW transmit
timestamping"), __sock_recv_timestamp has some logic for making sure
that the two calls to skb_tstamp_tx:
skb_tx_timestamp(skb) # Software timestamp in the driver
-> skb_tstamp_tx(skb, NULL)
and
skb_tstamp_tx(skb, &shhwtstamps) # Hardware timestamp in the driver
will both do the right thing and in a race-free manner, meaning that
skb_tx_timestamp will deliver a cmsg with the software timestamp only,
and skb_tstamp_tx with a non-NULL hwtstamps argument will deliver a cmsg
with the hardware timestamp only.
Why are races even possible? Well, because although the software timestamp
skb->tstamp is private per skb, the hardware timestamp skb_hwtstamps(skb)
lives in skb_shinfo(skb), an area which is shared between skbs and their
clones. And skb_tstamp_tx works by cloning the packets when timestamping
them, therefore attempting to perform hardware timestamping on an skb's
clone will also change the hardware timestamp of the original skb. And
the original skb might have been yet again cloned for software
timestamping, at an earlier stage.
So the logic in __sock_recv_timestamp can't be as simple as saying
"does this skb have a hardware timestamp? if yes I'll send the hardware
timestamp to the socket, otherwise I'll send the software timestamp",
precisely because the hardware timestamp is shared.
Instead, it's quite the other way around: __sock_recv_timestamp says
"does this skb have a software timestamp? if yes, I'll send the software
timestamp, otherwise the hardware one". This works because the software
timestamp is not shared with clones.
But that means we have a problem when we attempt hardware timestamping
with skbs that don't have the skb->tstamp == 0. __sock_recv_timestamp
will say "oh, yeah, this must be some sort of odd clone" and will not
deliver the hardware timestamp to the socket. And this is exactly what
is happening when we have txtime enabled on the socket: as mentioned,
that is put in a union with skb->tstamp, so it is quite easy to mistake
it.
Do what other drivers do (intel igb/igc) and write zero to skb->tstamp
before taking the hardware timestamp. It's of no use to us now (we're
already on the TX confirmation path).
Fixes: 0d08c9ec7d ("enetc: add support time specific departure base on the qos etf")
Cc: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On LS1028A, the MAC RX FIFO defaults to the value 2, which is too high
and may lead to RX lock-up under traffic at a rate higher than 6 Gbps.
Set it to 1 instead, as recommended by the hardware design team and by
later versions of the ENETC block guide.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using jumbo packets and overrunning rx queue with napi enabled,
the following sequence is observed in gfar_add_rx_frag:
| lstatus | | skb |
t | lstatus, size, flags | first | len, data_len, *ptr |
---+--------------------------------------+-------+-----------------------+
13 | 18002348, 9032, INTERRUPT LAST | 0 | 9600, 8000, f554c12e |
12 | 10000640, 1600, INTERRUPT | 0 | 8000, 6400, f554c12e |
11 | 10000640, 1600, INTERRUPT | 0 | 6400, 4800, f554c12e |
10 | 10000640, 1600, INTERRUPT | 0 | 4800, 3200, f554c12e |
09 | 10000640, 1600, INTERRUPT | 0 | 3200, 1600, f554c12e |
08 | 14000640, 1600, INTERRUPT FIRST | 0 | 1600, 0, f554c12e |
07 | 14000640, 1600, INTERRUPT FIRST | 1 | 0, 0, f554c12e |
06 | 1c000080, 128, INTERRUPT LAST FIRST | 1 | 0, 0, abf3bd6e |
05 | 18002348, 9032, INTERRUPT LAST | 0 | 8000, 6400, c5a57780 |
04 | 10000640, 1600, INTERRUPT | 0 | 6400, 4800, c5a57780 |
03 | 10000640, 1600, INTERRUPT | 0 | 4800, 3200, c5a57780 |
02 | 10000640, 1600, INTERRUPT | 0 | 3200, 1600, c5a57780 |
01 | 10000640, 1600, INTERRUPT | 0 | 1600, 0, c5a57780 |
00 | 14000640, 1600, INTERRUPT FIRST | 1 | 0, 0, c5a57780 |
So at t=7 a new packets is started but not finished, probably due to rx
overrun - but rx overrun is not indicated in the flags. Instead a new
packets starts at t=8. This results in skb->len to exceed size for the LAST
fragment at t=13 and thus a negative fragment size added to the skb.
This then crashes:
kernel BUG at include/linux/skbuff.h:2277!
Oops: Exception in kernel mode, sig: 5 [#1]
...
NIP [c04689f4] skb_pull+0x2c/0x48
LR [c03f62ac] gfar_clean_rx_ring+0x2e4/0x844
Call Trace:
[ec4bfd38] [c06a84c4] _raw_spin_unlock_irqrestore+0x60/0x7c (unreliable)
[ec4bfda8] [c03f6a44] gfar_poll_rx_sq+0x48/0xe4
[ec4bfdc8] [c048d504] __napi_poll+0x54/0x26c
[ec4bfdf8] [c048d908] net_rx_action+0x138/0x2c0
[ec4bfe68] [c06a8f34] __do_softirq+0x3a4/0x4fc
[ec4bfed8] [c0040150] run_ksoftirqd+0x58/0x70
[ec4bfee8] [c0066ecc] smpboot_thread_fn+0x184/0x1cc
[ec4bff08] [c0062718] kthread+0x140/0x144
[ec4bff38] [c0012350] ret_from_kernel_thread+0x14/0x1c
This patch fixes this by checking for computed LAST fragment size, so a
negative sized fragment is never added.
In order to prevent the newer rx frame from getting corrupted, the FIRST
flag is checked to discard the incomplete older frame.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX rings have a producer index owned by hardware, where newly
received frame buffers are placed, and a consumer index owned by
software, where newly allocated buffers are placed, in expectation of
hardware being able to place frame data in them.
Hardware increments the producer index when a frame is received, however
it is not allowed to increment the producer index to match the consumer
index (RBCIR) since the ring can hold at most RBLENR[LENGTH]-1 received
BDs. Whenever the producer index matches the value of the consumer
index, the ring has no unprocessed received frames and all BDs in the
ring have been initialized/prepared by software, i.e. hardware owns all
BDs in the ring.
The code uses the next_to_clean variable to keep track of the producer
index, and the next_to_use variable to keep track of the consumer index.
The RX rings are seeded from enetc_refill_rx_ring, which is called from
two places:
1. initially the ring is seeded until full with enetc_bd_unused(rx_ring),
i.e. with 511 buffers. This will make next_to_clean=0 and next_to_use=511:
.ndo_open
-> enetc_open
-> enetc_setup_bdrs
-> enetc_setup_rxbdr
-> enetc_refill_rx_ring
2. then during the data path processing, it is refilled with 16 buffers
at a time:
enetc_msix
-> napi_schedule
-> enetc_poll
-> enetc_clean_rx_ring
-> enetc_refill_rx_ring
There is just one problem: the initial seeding done during .ndo_open
updates just the producer index (ENETC_RBPIR) with 0, and the software
next_to_clean and next_to_use variables. Notably, it will not update the
consumer index to make the hardware aware of the newly added buffers.
Wait, what? So how does it work?
Well, the reset values of the producer index and of the consumer index
of a ring are both zero. As per the description in the second paragraph,
it means that the ring is full of buffers waiting for hardware to put
frames in them, which by coincidence is almost true, because we have in
fact seeded 511 buffers into the ring.
But will the hardware attempt to access the 512th entry of the ring,
which has an invalid BD in it? Well, no, because in order to do that, it
would have to first populate the first 511 entries, and the NAPI
enetc_poll will kick in by then. Eventually, after 16 processed slots
have become available in the RX ring, enetc_clean_rx_ring will call
enetc_refill_rx_ring and then will [ finally ] update the consumer index
with the new software next_to_use variable. From now on, the
next_to_clean and next_to_use variables are in sync with the producer
and consumer ring indices.
So the day is saved, right? Well, not quite. Freeing the memory
allocated for the rings is done in:
enetc_close
-> enetc_clear_bdrs
-> enetc_clear_rxbdr
-> this just disables the ring
-> enetc_free_rxtx_rings
-> enetc_free_rx_ring
-> sets next_to_clean and next_to_use to 0
but again, nothing is committed to the hardware producer and consumer
indices (yay!). The assumption is that the ring is disabled, so the
indices don't matter anyway, and it's the responsibility of the "open"
code path to set those up.
.. Except that the "open" code path does not set those up properly.
While initially, things almost work, during subsequent enetc_close ->
enetc_open sequences, we have problems. To be precise, the enetc_open
that is subsequent to enetc_close will again refill the ring with 511
entries, but it will leave the consumer index untouched. Untouched
means, of course, equal to the value it had before disabling the ring
and draining the old buffers in enetc_close.
But as mentioned, enetc_setup_rxbdr will at least update the producer
index though, through this line of code:
enetc_rxbdr_wr(hw, idx, ENETC_RBPIR, 0);
so at this stage we'll have:
next_to_clean=0 (in hardware 0)
next_to_use=511 (in hardware we'll have the refill index prior to enetc_close)
Again, the next_to_clean and producer index are in sync and set to
correct values, so the driver manages to limp on. Eventually, 16 ring
entries will be consumed by enetc_poll, and the savior
enetc_clean_rx_ring will come and call enetc_refill_rx_ring, and then
update the hardware consumer ring based upon the new next_to_use.
So.. it works?
Well, by coincidence, it almost does, but there's a circumstance where
enetc_clean_rx_ring won't be there to save us. If the previous value of
the consumer index was 15, there's a problem, because the NAPI poll
sequence will only issue a refill when 16 or more buffers have been
consumed.
It's easiest to illustrate this with an example:
ip link set eno0 up
ip addr add 192.168.100.1/24 dev eno0
ping 192.168.100.1 -c 20 # ping this port from another board
ip link set eno0 down
ip link set eno0 up
ping 192.168.100.1 -c 20 # ping it again from the same other board
One by one:
1. ip link set eno0 up
-> calls enetc_setup_rxbdr:
-> calls enetc_refill_rx_ring(511 buffers)
-> next_to_clean=0 (in hw 0)
-> next_to_use=511 (in hw 0)
2. ping 192.168.100.1 -c 20 # ping this port from another board
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=1 next_to_clean 0 (in hw 1) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=2 next_to_clean 1 (in hw 2) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=3 next_to_clean 2 (in hw 3) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=4 next_to_clean 3 (in hw 4) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=5 next_to_clean 4 (in hw 5) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=6 next_to_clean 5 (in hw 6) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=7 next_to_clean 6 (in hw 7) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=8 next_to_clean 7 (in hw 8) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=9 next_to_clean 8 (in hw 9) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=10 next_to_clean 9 (in hw 10) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=11 next_to_clean 10 (in hw 11) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=12 next_to_clean 11 (in hw 12) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=13 next_to_clean 12 (in hw 13) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=14 next_to_clean 13 (in hw 14) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=15 next_to_clean 14 (in hw 15) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: enetc_refill_rx_ring(16) increments next_to_use by 16 (mod 512) and writes it to hw
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=0 next_to_clean 15 (in hw 16) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=1 next_to_clean 16 (in hw 17) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=2 next_to_clean 17 (in hw 18) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=3 next_to_clean 18 (in hw 19) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=4 next_to_clean 19 (in hw 20) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=5 next_to_clean 20 (in hw 21) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=6 next_to_clean 21 (in hw 22) next_to_use 15 (in hw 15)
20 packets transmitted, 20 packets received, 0% packet loss
3. ip link set eno0 down
enetc_free_rx_ring: next_to_clean 0 (in hw 22), next_to_use 0 (in hw 15)
4. ip link set eno0 up
-> calls enetc_setup_rxbdr:
-> calls enetc_refill_rx_ring(511 buffers)
-> next_to_clean=0 (in hw 0)
-> next_to_use=511 (in hw 15)
5. ping 192.168.100.1 -c 20 # ping it again from the same other board
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=1 next_to_clean 0 (in hw 1) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=2 next_to_clean 1 (in hw 2) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=3 next_to_clean 2 (in hw 3) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=4 next_to_clean 3 (in hw 4) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=5 next_to_clean 4 (in hw 5) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=6 next_to_clean 5 (in hw 6) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=7 next_to_clean 6 (in hw 7) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=8 next_to_clean 7 (in hw 8) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=9 next_to_clean 8 (in hw 9) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=10 next_to_clean 9 (in hw 10) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=11 next_to_clean 10 (in hw 11) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=12 next_to_clean 11 (in hw 12) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=13 next_to_clean 12 (in hw 13) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=14 next_to_clean 13 (in hw 14) next_to_use 511 (in hw 15)
20 packets transmitted, 12 packets received, 40% packet loss
And there it dies. No enetc_refill_rx_ring (because cleaned_cnt must be equal
to 15 for that to happen), no nothing. The hardware enters the condition where
the producer (14) + 1 is equal to the consumer (15) index, which makes it
believe it has no more free buffers to put packets in, so it starts discarding
them:
ip netns exec ns0 ethtool -S eno0 | grep -v ': 0'
NIC statistics:
Rx ring 0 discarded frames: 8
Summarized, if the interface receives between 16 and 32 (mod 512) frames
and then there is a link flap, then the port will eventually die with no
way to recover. If it receives less than 16 (mod 512) frames, then the
initial NAPI poll [ before the link flap ] will not update the consumer
index in hardware (it will remain zero) which will be ok when the buffers
are later reinitialized. If more than 32 (mod 512) frames are received,
the initial NAPI poll has the chance to refill the ring twice, updating
the consumer index to at least 32. So after the link flap, the consumer
index is still wrong, but the post-flap NAPI poll gets a chance to
refill the ring once (because it passes through cleaned_cnt=15) and
makes the consumer index be again back in sync with next_to_use.
The solution to this problem is actually simple, we just need to write
next_to_use into the hardware consumer index at enetc_open time, which
always brings it back in sync after an initial buffer seeding process.
The simpler thing would be to put the write to the consumer index into
enetc_refill_rx_ring directly, but there are issues with the MDIO
locking: in the NAPI poll code we have the enetc_lock_mdio() taken from
top-level and we use the unlocked enetc_wr_reg_hot, whereas in
enetc_open, the enetc_lock_mdio() is not taken at the top level, but
instead by each individual enetc_wr_reg, so we are forced to put an
additional enetc_wr_reg in enetc_setup_rxbdr. Better organization of
the code is left as a refactoring exercise.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Station Interface Receive Interrupt Detect Register (SIRXIDR)
contains a 16-bit wide mask of 'interrupt detected' events for each ring
associated with a port. Bit i is write-1-to-clean for RX ring i.
I have no explanation whatsoever how this line of code came to be
inserted in the blamed commit. I checked the downstream versions of that
patch and none of them have it.
The somewhat comical aspect of it is that we're writing a binary number
to the SIRXIDR register, which is derived from enetc_bd_unused(rx_ring).
Since the RX rings have 512 buffer descriptors, we end up writing 511 to
this register, which is 0x1ff, so we are effectively clearing the
'interrupt detected' event for rings 0-8.
This register is not what is used for interrupt handling though - it
only provides a summary for the entire SI. The hardware provides one
separate Interrupt Detect Register per RX ring, which auto-clears upon
read. So there doesn't seem to be any adverse effect caused by this
bogus write.
There is, however, one reason why this should be handled as a bugfix:
next_to_clean _should_ be committed to hardware, just not to that
register, and this was obscuring the fact that it wasn't. This is fixed
in the next patch, and removing the bogus line now allows the fix patch
to be backported beyond that point.
Fixes: fd5736bf9f ("enetc: Workaround for MDIO register access issue")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ENETC port 0 MAC supports in-band status signaling coming from a PHY
when operating in RGMII mode, and this feature is enabled by default.
It has been reported that RGMII is broken in fixed-link, and that is not
surprising considering the fact that no PHY is attached to the MAC in
that case, but a switch.
This brings us to the topic of the patch: the enetc driver should have
not enabled the optional in-band status signaling for RGMII unconditionally,
but should have forced the speed and duplex to what was resolved by
phylink.
Note that phylink does not accept the RGMII modes as valid for in-band
signaling, and these operate a bit differently than 1000base-x and SGMII
(notably there is no clause 37 state machine so no ACK required from the
MAC, instead the PHY sends extra code words on RXD[3:0] whenever it is
not transmitting something else, so it should be safe to leave a PHY
with this option unconditionally enabled even if we ignore it). The spec
talks about this here:
https://e2e.ti.com/cfs-file/__key/communityserver-discussions-components-files/138/RGMIIv1_5F00_3.pdf
Fixes: 71b77a7a27 ("enetc: Migrate to PHYLINK and PCS_LYNX")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting from the blamed commit:
In promiscuous mode, it is more intuitive that all traffic is received,
including VLAN tagged traffic. It appears that it is necessary to set
the flag in PSIPVMR for that to be the case, so VLAN promiscuous mode is
also temporarily enabled. On exit from promiscuous mode, the setting
made by ethtool is restored.
Intuitive or not, there isn't any definition issued by a standards body
which says that promiscuity has anything to do with VLAN filtering - it
only has to do with accepting packets regardless of destination MAC address.
In fact people are already trying to use this misunderstanding/bug of
the enetc driver as a justification to transform promiscuity into
something it never was about: accepting every packet (maybe that would
be the "rx-all" netdev feature?):
https://lore.kernel.org/netdev/20201110153958.ci5ekor3o2ekg3ky@ipetronik.com/
This is relevant because there are use cases in the kernel (such as
tc-flower rules with the protocol 802.1Q and a vlan_id key) which do not
(yet) use the vlan_vid_add API to be compatible with VLAN-filtering NICs
such as enetc, so for those, disabling rx-vlan-filter is currently the
only right solution to make these setups work:
https://lore.kernel.org/netdev/CA+h21hoxwRdhq4y+w8Kwgm74d4cA0xLeiHTrmT-VpSaM7obhkg@mail.gmail.com/
The blamed patch has unintentionally introduced one more way for this to
work, which is to enable IFF_PROMISC, however this is non-portable
because port promiscuity is not meant to disable VLAN filtering.
Therefore, it could invite people to write broken scripts for enetc, and
then wonder why they are broken when migrating to other drivers that
don't handle promiscuity in the same way.
Fixes: 7070eea5e9 ("enetc: permit configuration of rx-vlan-filter with ethtool")
Cc: Markus Blöchl <Markus.Bloechl@ipetronik.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the enetc ports have rx-vlan-offload enabled, they report a TPID of
ETH_P_8021Q regardless of what was actually in the packet. When
rx-vlan-offload is disabled, packets have the proper TPID. Fix this
inconsistency by finishing the TODO left in the code.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workaround for the ENETC MDIO erratum caused a performance
degradation of 82 Kpps (seen with IP forwarding of two 1Gbps streams of
64B packets). This is due to excessive locking and unlocking in the fast
path, which can be avoided.
By taking the MDIO read-side lock only once per NAPI poll cycle, we are
able to regain 54 Kpps (65%) of the performance hit. The rest of the
performance degradation comes from the TX data path, but unfortunately
it doesn't look like we can optimize that away easily, even with
netdev_xmit_more(), there just isn't any skb batching done, to help with
taking the MDIO lock less often than once per packet.
We need to change the register accessor type for enetc_get_tx_tstamp,
because it now runs under the enetc_lock_mdio as per the new call path
detailed below:
enetc_msix
-> napi_schedule
-> enetc_poll
-> enetc_lock_mdio
-> enetc_clean_tx_ring
-> enetc_get_tx_tstamp
-> enetc_clean_rx_ring
-> enetc_unlock_mdio
Fixes: fd5736bf9f ("enetc: Workaround for MDIO register access issue")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael reports that since linux-next-20210211, the AER messages for ECC
errors have started reappearing, and this time they can be reliably
reproduced with the first ping on one of his LS1028A boards.
$ ping 1[ 33.258069] pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0
72.16.0.1
PING [ 33.267050] pcieport 0000:00:1f.0: AER: can't find device of ID0000
172.16.0.1 (172.16.0.1): 56 data bytes
64 bytes from 172.16.0.1: seq=0 ttl=64 time=17.124 ms
64 bytes from 172.16.0.1: seq=1 ttl=64 time=0.273 ms
$ devmem 0x1f8010e10 32
0xC0000006
It isn't clear why this is necessary, but it seems that for the errors
to go away, we must clear the entire RFS and RSS memory, not just for
the ports in use.
Sadly the code is structured in such a way that we can't have unified
logic for the used and unused ports. For the minimal initialization of
an unused port, we need just to enable and ioremap the PF memory space,
and a control buffer descriptor ring. Unused ports must then free the
CBDR because the driver will exit, but used ports can not pick up from
where that code path left, since the CBDR API does not reinitialize a
ring when setting it up, so its producer and consumer indices are out of
sync between the software and hardware state. So a separate
enetc_init_unused_port function was created, and it gets called right
after the PF memory space is enabled.
Fixes: 07bf34a50e ("net: enetc: initialize the RFS and RSS memories")
Reported-by: Michael Walle <michael@walle.cc>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the blamed patch, all RX traffic gets hashed to CPU 0 because the
hashing indirection table set up in:
enetc_pf_probe
-> enetc_alloc_si_resources
-> enetc_configure_si
-> enetc_setup_default_rss_table
is overwritten later in:
enetc_pf_probe
-> enetc_init_port_rss_memory
which zero-initializes the entire port RSS table in order to avoid ECC errors.
The trouble really is that enetc_init_port_rss_memory really neads
enetc_alloc_si_resources to be called, because it depends upon
enetc_alloc_cbdr and enetc_setup_cbdr. But that whole enetc_configure_si
thing could have been better thought out, it has nothing to do in a
function called "alloc_si_resources", especially since its counterpart,
"free_si_resources", does nothing to unwind the configuration of the SI.
The point is, we need to pull out enetc_configure_si out of
enetc_alloc_resources, and move it after enetc_init_port_rss_memory.
This allows us to set up the default RSS indirection table after
initializing the memory.
Fixes: 07bf34a50e ("net: enetc: initialize the RFS and RSS memories")
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When accessing the timecounter register on an i.MX8MQ the kernel hangs.
This is only the case when the interface is down. This can be reproduced
by reading with 'phc_ctrl eth0 get'.
Like described in the change in 91c0d987a9
the igp clock is disabled when the interface is down and leads to a
system hang.
So we check if the ptp clock status before reading the timecounter
register.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20210225211514.9115-1-heiko.thiery@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current use of container_of is flawed and unnecessary. Obtain
the dpaa_napi_portal reference from the private percpu data instead.
Fixes: a1e031ffb4 ("dpaa_eth: add XDP_REDIRECT support")
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/r/20210218182106.22613-1-camelia.groza@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The following call path suggests that calling unregister_netdev on an
interface that is up will first bring it down.
enetc_pf_remove
-> unregister_netdev
-> unregister_netdevice_queue
-> unregister_netdevice_many
-> dev_close_many
-> __dev_close_many
-> enetc_close
-> enetc_stop
-> phylink_stop
However, enetc first destroys the phylink instance, then calls
unregister_netdev. This is already dissimilar to the setup (and error
path teardown path) from enetc_pf_probe, but more than that, it is buggy
because it is invalid to call phylink_stop after phylink_destroy.
So let's first unregister the netdev (and let the .ndo_stop events
consume themselves), then destroy the phylink instance, then free the
netdev.
Fixes: 71b77a7a27 ("enetc: Migrate to PHYLINK and PCS_LYNX")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If xdp_do_redirect() fails, the calling driver should handle recycling
or freeing of the page associated with the frame. The dpaa2-eth driver
didn't do either of them and just incremented a counter.
Fix this by trying to DMA map back the page and recycle it or, if the
mapping fails, just free it.
Fixes: d678be1dc1 ("dpaa2-eth: add XDP_REDIRECT support")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FSL_ENETC_MDIO use symbols from PHYLIB (MDIO_BUS) and MDIO_DEVRES,
however there are no dependency specified in Kconfig
ERROR: modpost: "__mdiobus_register" [drivers/net/ethernet/freescale/enetc/fsl-enetc-mdio.ko] undefined!
ERROR: modpost: "mdiobus_unregister" [drivers/net/ethernet/freescale/enetc/fsl-enetc-mdio.ko] undefined!
ERROR: modpost: "devm_mdiobus_alloc_size" [drivers/net/ethernet/freescale/enetc/fsl-enetc-mdio.ko] undefined!
add depends on MDIO_DEVRES && MDIO_BUS
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for backplane link mode, which is, according to discussions
with NXP earlier in the year, is a mode where the OS (Linux) is able to
manage the PCS and Serdes itself.
This commit prepares the ground work for allowing 1G fiber connections
to be used with DPAA2 on the SolidRun CEX7 platforms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that pcs-lynx supports 1000BASE-X, add support for this interface
mode to dpaa2-mac. pcs-lynx can be switched at runtime between SGMII
and 1000BASE-X mode, so allow dpaa2-mac to switch between these as
well.
This commit prepares the ground work for allowing 1G fiber connections
to be used with DPAA2 on the SolidRun CEX7 platforms.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The napi_alloc_frag_align() will guarantee that a correctly align
buffer address is returned. So use this function to simplify the buffer
alloc and avoid the unnecessary memory waste.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the following coccicheck warnings:
./drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c:1651:36-38: WARNING
!A || A && B is equivalent to !A || B.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1612260157-128026-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The XDP frame's headroom might be large enough to accommodate the
xdpf backpointer as well as shifting the data to an aligned address.
Try this first before resorting to allocating a new buffer and copying
the data.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 256 byte data alignment is required for preventing DMA transaction
splits when crossing 4K page boundaries. Since XDP deals only with page
sized buffers or less, this restriction isn't needed. Instead, the data
only needs to be aligned to 64 bytes to prevent DMA transaction splits.
These lessened restrictions can increase performance by widening the pool
of permitted data alignments and preventing unnecessary realignments.
Fixes: ae680bcbd0 ("dpaa_eth: implement the A050385 erratum workaround for XDP")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
