In rvu_mbox_init(), mbox_regions is not freed or passed out
under the switch-default region, which could lead to a memory leak.
Fix this bug by changing 'return err' to 'goto free_regions'.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_OCTEONTX2_AF=y show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 98c5611163 (“octeontx2-af: cn10k: Add mbox support for CN10K platform”)
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130165039.192426-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Perform CPT LF teardown in non FLR path as well via cpt_lf_free()
Currently CPT LF teardown and reset sequence is only
done when FLR is handled with CPT LF still attached.
This patch also fixes cpt_lf_alloc() to set EXEC_LDWB in
CPT_AF_LFX_CTL2 when being completely overwritten as that is
the default value and is better for performance.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch enables and registers interrupt handler for CPT HW
interrupts.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> #mlx*
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP hardware block can be configured to utilize
the external clock. Also the current ptp timestamp
can be captured when external trigger is applied on
a gpio pin. These features are required in scenarios
like connecting a external timing device to the chip
for time synchronization. The timing device provides
the clock and trigger(PPS signal) to the PTP block.
This patch does the following:
1. configures PTP block to use external clock
frequency and timestamp capture on external event.
2. sends PTP_REQ_EXTTS events to kernel ptp phc susbsytem
with captured timestamps
3. aligns PPS edge to adjusted ptp clock in the ptp device
by setting the PPS_THRESH to the reminder of the last
timestamp value captured by external PPS
Signed-off-by: Yi Guo <yig@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The input clock frequency of PTP block is figured
out from hardware reset block currently. The firmware
data already has this info in sclk. Hence simplify
ptp driver to use sclk from firmware data.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable blkaddr is being initialized with a value that is never
read, it is being updated later on in a for-loop. The assignment is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On OcteonTX2/CN10K SoC, the admin function (AF) is the only one
with all priviliges to configure HW and alloc resources, PFs and
it's VFs have to request AF via mailbox for all their needs.
This patch adds new mailbox messages for CPT PFs and VFs to configure
HW resources for inline-IPsec.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Vidya Sagar Velumuri <vvelumuri@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to match 'rvu_alloc_bitmap()', add a 'rvu_free_bitmap()' function
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check one more time before exiting the API with an error.
Fix API to poll at least twice, in case there are other high priority
tasks and this API doesn't get CPU cycles for multiple jiffies update.
In addition, increase timeout from usecs_to_jiffies(10000) to
usecs_to_jiffies(20000), to prevent the case that for CONFIG_100HZ
timeout will be a single jiffies.
A single jiffies results actual timeout that can be any time between
1usec and 10msec. To solve this, a value of usecs_to_jiffies(20000)
ensures that timeout is 2 jiffies.
Signed-off-by: Smadar Fuks <smadarf@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed inconsistent license text across the RVU admin
function driver.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving the MBOX_MSG_FREE_RSRC_CNT, the AF will find out the
current number of free resources and reply it back to the requester. No
guarantee is given on the future state of the free resources yet.
If another requester sends MBOX_MSG_ATTACH_RESOURCES after this call,
the number of available resources might change.
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for packet IO via SDK links which is used when
Octeon is connected as a end-point. Traffic host to end-point
and vice versa flow through SDP links. This patch also support
dual SDP blocks supported in 98xx silicon.
Signed-off-by: Radha Mohan Chintakuntla <radhac@marvell.com>
Signed-off-by: Nalla Pradeep <pnalla@marvell.com>
Signed-off-by: Subrahmanyam Nilla <snilla@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from 96xx C0 onwards all silicons support traffic shaping.
This patch enables that feature along with other changes
- When PIR/CIR shaping config is modified, toggle SW_XOFF
for config to take effect
- Before SMQ flush, clear SW_XOFF at all parent schedulers
- Support to read current transmit scheduler configuration via mbox
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear and disable interrupt before queueing work as there might be
a chance that work gets completed on other core faster and
interrupt enable as a part of the work completes before
interrupt disable in the interrupt context. This leads to
permanent disable of interrupt.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print debug message if any of the RVU hardware blocks
reset fails.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change added error checking messages and failed to remove one
of the previous error checks. There are now two checks on variable err
so the second one is redundant dead code and can be removed.
Addresses-Coverity: ("Logically dead code")
Fixes: a83bdada06 ("octeontx2-af: Add debug messages for failures")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210818130927.33895-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Added debug messages for various failures during probe.
This will help in quickly identifying the API where the failure
is happening.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the number of VFs of a PF correctly by calling
rvu_get_pf_numvfs in rvu_switch_disable function.
Also hwvf is not required hence remove it.
Fixes: 23109f8dd0 ("octeontx2-af: Introduce internal packet switching")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of now any communication between CGXs PFs and
their VFs within the system is possible only by
external switches sending packets back to the
system. This patch adds internal switching support.
Broadcast packet replication is not covered here.
RVU admin function (AF) maintains MAC addresses
of all interfaces in the system. When switching is
enabled, MCAM entries are allocated to install rules
such that packets with DMAC matching any of the
internal interface MAC addresses is punted back
into the system via the loopback channel.
On the receive side the default unicast rules
are modified to not check for ingress channel.
So any packet with matching DMAC irrespective of
which interface it is coming from will be forwarded
to the respective PF/VF interface.
The transmit side rules and default unicast rules
are updated if user changes MAC address of an interface.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For enabling VF-VF switching the packets egressing
out of CGX mapped VFs needed to be sent to LBK
so that same packets are received back to the system.
But the LBK link also needs to be enabled in addition
to a VF's mapped CGX_LMAC link otherwise hardware
raises send error interrupt indicating selected LBK
link is not enabled in NIX_AF_TL3_TL2X_LINKX_CFG register.
Hence this patch enables all LBK links in
TL3_TL2_LINKX_CFG registers.
Also to enable packet flow between PFs/VFs of NIX0
to PFs/VFs of NIX1(in 98xx silicon) the NPC TX DMAC
rules has to be installed such that rules must be hit
for any TX interface i.e., NIX0-TX or NIX1-TX provided
DMAC match creteria is met. Hence this patch changes the
behavior such that MCAM is programmed to match with any
NIX0/1-TX interface for TX rules.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introducing a new mailbox to support updating lmt entries
and common lmt base address scheme i.e. multiple pcifuncs
can share lmt region to reduce L1 cache pressure for application.
Parameters passed to mailbox includes the primary pcifunc
value whose lmt regions will be shared by other secondary
pcifuncs. Here secondary pcifunc will be the one who is
calling the mailbox.
For example:
By default each pcifunc has its own LMT base address:
PCIFUNC1 LMT_BASE_ADDR A
PCIFUNC2 LMT_BASE_ADDR B
PCIFUNC3 LMT_BASE_ADDR C
PCIFUNC4 LMT_BASE_ADDR D
Application will choose PCIFUNC1 as base/primary pcifunc
and as and when other pcifunc(secondary pcifuncs) gets
probed, this mailbox will be called and LMTST table will
be updated as:
PCIFUNC1 LMT_BASE_ADDR A
PCIFUNC2 LMT_BASE_ADDR A
PCIFUNC3 LMT_BASE_ADDR A
PCIFUNC4 LMT_BASE_ADDR A
On FLR lmtst map table gets resetted to the default lmt
base addresses for all secondary pcifuncs.
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for dumping current resource status of bandwidth
profiles and contexts of allocated profiles via debugfs.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new mailbox to enable PF to configure VF as trusted VF.
Trusted VF feature allows VFs to perform priviliged operations
such as enabling VF promiscuous mode, all-multicast mode and
changing the VF MAC address configured by PF. Refactored the
VF interface flags maintained by the AF driver such that the
flags do not overlap for various configurations.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ability to load a set of custom KPU entries. This
allows for flexible support for custom protocol parsing.
AF driver will attempt to load the profile and verify if it can fit
hardware capabilities. If not, it will revert to the built-in profile.
Next it will replace the first KPU_MAX_CST_LT (2) entries in each KPU
in default profile with entries read from the profile image.
The built-in profile should always contain KPU_MAX_CSR_LT first no-match
entries and AF driver will disable those in the KPU unless custom
profile is loaded.
Profile file contains also a list of default protocol overrides to
allow for custom protocols to be used there.
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current devlink code try to free already freed irqs as the
irq_allocate flag is not cleared after free leading to kernel
crash while removing rvu driver. The patch fixes the irq free
sequence and clears the irq_allocate flag on free.
Fixes: 7304ac4567 ("octeontx2-af: Add mailbox IRQ and msg handlers")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OcteonTx3 CN10K silicon supports bigger MTU when compared
to 9216 MTU supported by OcteonTx2 silicon variants. Lookback
interface supports upto 64K and RPM LMAC interfaces support
upto 16K.
This patch does the necessary configuration and adds support
for PF/VF drivers to retrieve max packet size supported via mbox
This patch also configures tx link credit by considering supported
fifo size and max packet length for Octeontx3 silicon.
This patch also removes platform specific name from the driver name.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIX uses unique channel numbers to identify the packet sources/sinks
like CGX,LBK and SDP. The channel numbers assigned to each block are
hardwired in CN9xxx silicon.
The fixed channel numbers in CN9xxx are:
0x0 | a << 8 | b - LBK(0..3)_CH(0..63)
0x0 | a << 8 - Reserved
0x700 | a - SDP_CH(0..255)
0x800 | a << 8 | b << 4 | c - CGX(0..7)_LMAC(0..3)_CH(0..15)
All the channels in the above fixed enumerator(with maximum
number of blocks) are not required since some chips
have less number of blocks.
For CN10K silicon the channel numbers need to be programmed by
software in each block with the base channel number and range of
channels. This patch calculates and assigns the channel numbers
to efficiently distribute the channel number range(0-4095) among
all the blocks. The assignment is made based on the actual number of
blocks present and also contiguously leaving no holes.
The channel numbers remaining after the math are used as new CPT
replay channels present in CN10K. Also since channel numbers are
not fixed the transmit channel link number needed by AF consumers
is calculated by AF and sent along with nix_lf_alloc mailbox response.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware allocates memory regions for PFs and VFs in DRAM.
The PFs memory region is used for AF-PF and PF-VF mailbox.
This mbox facilitates communication between AF-PF and PF-VF.
On CN10K platform:
The DRAM region allocated to PF is enumerated as PF BAR4 memory.
PF BAR4 contains AF-PF mbox region followed by its VFs mbox region.
AF-PF mbox region base address is configured at RVU_AF_PFX_BAR4_ADDR
PF-VF mailbox base address is configured at
RVU_PF(x)_VF_MBOX_ADDR = RVU_AF_PF()_BAR4_ADDR+64KB. PF access its
mbox region via BAR4, whereas VF accesses PF-VF DRAM mailboxes via
BAR2 indirect access.
On CN9XX platform:
Mailbox region in DRAM is divided into two parts AF-PF mbox region and
PF-VF mbox region i.e all PFs mbox region is contiguous similarly all
VFs.
The base address of the AF-PF mbox region is configured at
RVU_AF_PF_BAR4_ADDR.
AF-PF1 mbox address can be calculated as RVU_AF_PF_BAR4_ADDR * mbox
size.
The base address of PF-VF mbox region for each PF is configure at
RVU_AF_PF(0..15)_VF_BAR4_ADDR.PF access its mbox region via BAR4 and its
VF mbox regions from RVU_PF_VF_BAR4_ADDR register, whereas VF access its
mbox region via BAR4.
This patch changes mbox initialization to support both CN9XX and CN10K
platform.
This patch also adds CN10K PTP subsystem and device IDs to ptp
driver id table.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When FLR is initiated for a VF (PCI function level reset),
the parent PF gets a interrupt. PF then sends a message to
admin function (AF), which then cleans up all resources
attached to that VF. This patch adds support to handle
CPT FLR.
Signed-off-by: Narayana Prasad Raju Atherya <pathreya@marvell.com>
Signed-off-by: Suheil Chandran <schandran@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add devlink support to AF driver. Basic devlink support is added.
Currently info_get is the only supported devlink ops.
devlink ouptput looks like this
# devlink dev
pci/0002:01:00.0
# devlink dev info
pci/0002:01:00.0:
driver octeontx2-af
#
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch handles the VF mac address changes as given below.
1. mac addr configrued by VF will be retained until VF module unload.
2. mac addr configred by PF for VF will be retained until power cycle.
3. mac addr confgired by PF for its VF can't be overwritten by VF.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds support to verify the channel number sent by
mailbox requester before writing MCAM entry for Ingress packets.
Similarly for Egress packets, verifying the PF_FUNC sent by the
mailbox user.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch puts together all mailbox changes
for 98xx silicon:
Attach ->
Modify resource attach mailbox handler to
request LFs from a block address out of multiple
blocks of same type. If a PF/VF need LFs from two
blocks of same type then attach mbox should be
called twice.
Example:
struct rsrc_attach *attach;
.. Allocate memory for message ..
attach->cptlfs = 3; /* 3 LFs from CPT0 */
.. Send message ..
.. Allocate memory for message ..
attach->modify = 1;
attach->cpt_blkaddr = BLKADDR_CPT1;
attach->cptlfs = 2; /* 2 LFs from CPT1 */
.. Send message ..
Detach ->
Update detach mailbox and its handler to detach
resources from CPT1 and NIX1 blocks.
MSIX ->
Updated the MSIX mailbox and its handler to return
MSIX offsets for the new block CPT1.
Free resources ->
Update free_rsrc mailbox and its handler to return
the free resources count of new blocks NIX1 and CPT1
Links ->
Number of CGX,LBK and SDP links may vary between
platforms. For example, in 98xx number of CGX and LBK
links are more than 96xx. Hence the info about number
of links present in hardware is useful for consumers to
request link configuration properly. This patch sends
this info in nix_lf_alloc_rsp.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On 98xx silicon, NPC block has additional
mcam entries, counters and NIX1 interfaces.
Extended set of registers are present for the
new mcam entries and counters.
This patch does the following:
- updates the register accessing macros
to use extended set if present.
- configures the MKEX profile for NIX1 interfaces also.
- updates mcam entry write functions to use assigned
NIX0/1 interfaces for the PF/VF.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Firmware configures NIX block mapping for all CGXs
to achieve maximum throughput. This patch reads
the configuration and create mapping between RVU
PF and NIX blocks. And for LBK VFs assign NIX0 for
even numbered VFs and NIX1 for odd numbered VFs.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch modifies NIX functions to operate
with nix_hw context so that existing functions
can be used for both NIX0 and NIX1 blocks. And
the NIX blocks present in the system are initialized
during driver init and freed during exit.
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
AF manages the tasks of allocating, freeing
LFs from RVU blocks to PF and VFs. With new
NIX1 and CPT1 blocks in 98xx, this patch
adds support for handling new blocks too.
Co-developed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since multiple blocks of same type are present in
98xx, modify functions which get resource count and
which update resource count to work with individual
block address instead of block type.
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Added tracepoints in mailbox code so that
the mailbox operations like message allocation,
sending message and message interrupts are traced.
Also the mailbox errors occurred like timeout
or wrong responses are traced.
These will help in debugging mailbox issues.
Here's an example output showing one of the mailbox
messages sent by PF to AF and AF responding to it:
~# mount -t tracefs none /sys/kernel/tracing/
~# echo 1 > /sys/kernel/tracing/events/rvu/enable
~# ifconfig eth0 up
~# cat /sys/kernel/tracing/trace
~# cat /sys/kernel/tracing/trace
tracer: nop
_-----=> irqs-off
/ _----=> need-resched
| / _---=> hardirq/softirq
|| / _--=> preempt-depth
||| / delay
TASK-PID CPU# |||| TIMESTAMP FUNCTION
| | | |||| | |
ifconfig-2382 [002] .... 756.161892: otx2_msg_alloc: [0002:02:00.0] msg:(0x400) size:40
ifconfig-2382 [002] ...1 756.161895: otx2_msg_send: [0002:02:00.0] sent 1 msg(s) of size:48
<idle>-0 [000] d.h1 756.161902: otx2_msg_interrupt: [0002:01:00.0] mbox interrupt PF(s) to AF (0x2)
kworker/u49:0-1165 [000] .... 756.162049: otx2_msg_process: [0002:01:00.0] msg:(0x400) error:0
kworker/u49:0-1165 [000] ...1 756.162051: otx2_msg_send: [0002:01:00.0] sent 1 msg(s) of size:32
kworker/u49:0-1165 [000] d.h. 756.162056: otx2_msg_interrupt: [0002:02:00.0] mbox interrupt AF to PF (0x1)
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Precision Timestamping block found on Octeontx2
platform is an independent coprocessor and has
internal PTP hardware clock. Once configured PTP
runs independently and when a packet arrives
CGX hardware block gets the current timestamp
from PTP block and forwards the packet to NIX
by prepending timestamp to the packet.
This patch adds the pci driver for PTP block.
The driver gets registered by AF driver and does
initial configuration and exposes a mailbox function to
read and adjust PTP hardware clock. The mailbox function
is called by AF consumers like netdev drivers or
userspace drivers. Since PTP being a single block
in platform this driver helps in accessing PTP
block by any AF consumer.
Co-developed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Aleksey Makarov <amakarov@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed MODULE_VERSION and fixed MODULE_AUTHOR.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently on the first check if the operation is still not
finished, the poll goes to sleep for 2-5 usecs. But if for
some reason (due to other priority stuff like interrupts etc) by
the time the poll wakes up the 10ms time is expired then we don't
check if operation is finished or not and return failure.
This patch modifies poll logic to check HW operation after sleep so
that the status is checked atleast twice.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bus mastering is enabled by firmware, but when this driver
is unbinded bus mastering gets disabled by the PCI subsystem
which results interrupts not working when driver is reloaded.
Hence set bus mastering everytime in probe().
Also
- Converted pci_set_dma_mask() and pci_set_consistent_dma_mask()
to dma_set_mask_and_coherent().
- Cleared transaction pending bit which gets set during
driver unbind due to clearing of bus mastering (ME bit).
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is no way for AF dependent drivers in
any domain to check if the AF driver is loaded. This
patch sets an ID for RVUM block which will automatically
reflects in PF/VFs discovery register which they can
check and defer their probe until AF is up.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For retrieving info like interface MAC addresses, packet
parser key extraction config etc currently a command
is sent to firmware and firmware which periodically polls
for commands, processes these and returns the info.
This is resulting in interface initialization taking lot
of time. To optimize this a memory region is shared between
firmware and this driver, firmware while booting puts
static info like these into that region for driver to
read directly without using commands.
With this
- Logic for retrieving packet parser extraction config
via commands is removed and repalced with using the
shared 'fwdata' structure.
- Now RVU MSIX vector address is also retrieved from this fwdata struct
instead of from CSR. Otherwise when kexec/kdump crash kernel loads
CSR will have a IOVA setup by primary kernel which impacts
RVU PF/VF's interrupts.
- Also added a mbox handler for PF/VF interfaces to retrieve their MAC
addresses from AF.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Traffic for a CGX mapped NIXLF can be stopped by disabling entries
in NPC MCAM or by configuring CGX and mailbox messages exist for the
two options. If traffic is stopped at CGX then VFs of that PF are
also effected hence CGX traffic should be started/stopped by
tracking all the users of it. This patch implements that CGX users
tracking. CGX is also configured along with NPC if required.
Also removed a check which mandates even number of LBK VFs.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ingress packet replication support has been added to 96xx B0
silicon. This patch enables using that feature to replicate
ingress broadcast packets to PF and it's VFs.
Also fixed below issues
- VFs can also install NPC MCAM entry to forward broadcast pkts.
Otherwise, unless PF's interface is UP, VFs will not receive
bcast packets.
- NPC MCAM entry is disabled when PF and all it's VFs are down.
- Few corner cases in installing multicast entry list.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
