Add support for OX810SE dwmac glue setup, which is a simplified version
of the OX820 introduced later with more control on the PHY interface.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In Linux bonding scenario, one packet is copied to several copies and sent
by all slave device of bond0 in mode 3(broadcast mode). The mode 3 xmit
function bond_xmit_broadcast() only ueses the last slave device's tx result
as the final result. In this case, if the last slave device is down, then
it always return NET_XMIT_DROP, even though the other slave devices xmit
success. It may cause the tx statistics error, and cause the application
(e.g. scp) consider the network is unreachable.
For example, use the following command to configure server A.
echo 3 > /sys/class/net/bond0/bonding/mode
ifconfig bond0 up
ifenslave bond0 eth0 eth1
ifconfig bond0 192.168.1.125
ifconfig eth0 up
ifconfig eth1 down
The slave device eth0 and eth1 are connected to server B(192.168.1.107).
Run the ping 192.168.1.107 -c 3 -i 0.2 command, the following information
is displayed.
PING 192.168.1.107 (192.168.1.107) 56(84) bytes of data.
64 bytes from 192.168.1.107: icmp_seq=1 ttl=64 time=0.077 ms
64 bytes from 192.168.1.107: icmp_seq=2 ttl=64 time=0.056 ms
64 bytes from 192.168.1.107: icmp_seq=3 ttl=64 time=0.051 ms
192.168.1.107 ping statistics
0 packets transmitted, 3 received
Actually, the slave device eth0 of the bond successfully sends three
ICMP packets, but the result shows that 0 packets are transmitted.
Also if we use scp command to get remote files, the command end with the
following printings.
ssh_exchange_identification: read: Connection timed out
So this patch modifies the bond_xmit_broadcast to return NET_XMIT_SUCCESS
if one slave device in the bond sends packets successfully. If all slave
devices send packets fail, the discarded packets stats is increased. The
skb is released when there is no slave device in the bond or the last slave
device is down.
Fixes: ae46f184bc ("bonding: propagate transmit status")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have seen cases where an endpoint RX completion interrupt arrives
while replenishing for the endpoint is underway. This causes another
instance of replenishing to begin as part of completing the receive
transaction. If this occurs it can lead to transaction corruption.
Use a new flag to ensure only one replenish instance for an endpoint
executes at a time.
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a new replenish_flags bitmap to contain Boolean flags
associated with an endpoint's replenishing state. Replace the
replenish_enabled field with a flag in that bitmap. This is to
prepare for the next patch, which adds another flag.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipa_endpoint_replenish(), if an error occurs when attempting to
replenish a receive buffer, we just quit and try again later. In
that case we increment the backlog count to reflect that the attempt
was unsuccessful. Then, if the add_one flag was true we increment
the backlog again.
This second increment is not included in the backlog local variable
though, and its value determines whether delayed work should be
scheduled. This is a bug.
Fix this by determining whether 1 or 2 should be added to the
backlog before adding it in a atomic_add_return() call.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the read-only const array offsets on the stack
but instead make it static. Also makes the object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220109231716.59012-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mask the ECN bits before calling mlx5e_route_lookup_ipv4_get(). The
tunnel key might have the last ECN bit set. This interferes with the
route lookup process as ip_route_output_key_hash() interpretes this bit
specially (to restrict the route scope).
Found by code inspection, compile tested only.
Fixes: c7b9038d8a ("net/mlx5e: TC preparation refactoring for routing update event")
Fixes: 9a941117fb ("net/mlx5e: Maximize ip tunnel key usage on the TC offloading path")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mask the ECN bits before calling ip_route_output_ports(). The tos
variable might be passed directly from an IPv4 header, so it may have
the last ECN bit set. This interferes with the route lookup process as
ip_route_output_key_hash() interpretes this bit specially (to restrict
the route scope).
Found by code inspection, compile tested only.
Fixes: 804c2f3e36 ("libcxgb,iw_cxgb4,cxgbit: add cxgb_find_route()")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch remove magic numbers in sun4i-emac.c and replace with macros
defined in sun4i-emac.h
Signed-off-by: Conley Lee <conleylee@foxmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Link: https://lore.kernel.org/r/tencent_71466C2135CD1780B19D7844BE3F167C940A@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 6bf950a8ff.
To align with other vendors, NET_VENDOR configs are supposed to be ON by
default, while their drivers should default to OFF.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20220110205246.66298-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Add new P-state driver for AMD processors (Huang Rui).
- Fix initialization of min and max frequency QoS requests in the
cpufreq core (Rafael Wysocki).
- Fix EPP handling on Alder Lake in intel_pstate (Srinivas Pandruvada).
- Make intel_pstate update cpuinfo.max_freq when notified of HWP
capabilities changes and drop a redundant function call from that
driver (Rafael Wysocki).
- Improve IRQ support in the Qcom cpufreq driver (Ard Biesheuvel,
Stephen Boyd, Vladimir Zapolskiy).
- Fix double devm_remap() in the Mediatek cpufreq driver (Hector Yuan).
- Introduce thermal pressure helpers for cpufreq CPU cooling (Lukasz
Luba).
- Make cpufreq use default_groups in kobj_type (Greg Kroah-Hartman).
- Make cpuidle use default_groups in kobj_type (Greg Kroah-Hartman).
- Fix two comments in cpuidle code (Jason Wang, Yang Li).
- Allow model-specific normal EPB value to be used in the intel_epb
sysfs attribute handling code (Srinivas Pandruvada).
- Simplify locking in pm_runtime_put_suppliers() (Rafael Wysocki).
- Add safety net to supplier device release in the runtime PM core
code (Rafael Wysocki).
- Capture device status before disabling runtime PM for it (Rafael
Wysocki).
- Add new macros for declaring PM operations to allow drivers to
avoid guarding them with CONFIG_PM #ifdefs or __maybe_unused and
update some drivers to use these macros (Paul Cercueil).
- Allow ACPI hardware signature to be honoured during restore from
hibernation (David Woodhouse).
- Update outdated operating performance points (OPP) documentation
(Tang Yizhou).
- Reduce log severity for informative message regarding frequency
transition failures in devfreq (Tzung-Bi Shih).
- Add DRAM frequency controller devfreq driver for Allwinner sunXi
SoCs (Samuel Holland).
- Add missing COMMON_CLK dependency to sun8i devfreq driver (Arnd
Bergmann).
- Add support for new layout of Psys PowerLimit Register on SPR to
the Intel RAPL power capping driver (Zhang Rui).
- Fix typo in a comment in idle_inject.c (Jason Wang).
- Remove unused function definition from the DTPM (Dynamit Thermal
Power Management) power capping framework (Daniel Lezcano).
- Reduce DTPM trace verbosity (Daniel Lezcano).
-----BEGIN PGP SIGNATURE-----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=1egI
-----END PGP SIGNATURE-----
Merge tag 'pm-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The most signigicant change here is the addition of a new cpufreq
'P-state' driver for AMD processors as a better replacement for the
venerable acpi-cpufreq driver.
There are also other cpufreq updates (in the core, intel_pstate, ARM
drivers), PM core updates (mostly related to adding new macros for
declaring PM operations which should make the lives of driver
developers somewhat easier), and a bunch of assorted fixes and
cleanups.
Summary:
- Add new P-state driver for AMD processors (Huang Rui).
- Fix initialization of min and max frequency QoS requests in the
cpufreq core (Rafael Wysocki).
- Fix EPP handling on Alder Lake in intel_pstate (Srinivas
Pandruvada).
- Make intel_pstate update cpuinfo.max_freq when notified of HWP
capabilities changes and drop a redundant function call from that
driver (Rafael Wysocki).
- Improve IRQ support in the Qcom cpufreq driver (Ard Biesheuvel,
Stephen Boyd, Vladimir Zapolskiy).
- Fix double devm_remap() in the Mediatek cpufreq driver (Hector
Yuan).
- Introduce thermal pressure helpers for cpufreq CPU cooling (Lukasz
Luba).
- Make cpufreq use default_groups in kobj_type (Greg Kroah-Hartman).
- Make cpuidle use default_groups in kobj_type (Greg Kroah-Hartman).
- Fix two comments in cpuidle code (Jason Wang, Yang Li).
- Allow model-specific normal EPB value to be used in the intel_epb
sysfs attribute handling code (Srinivas Pandruvada).
- Simplify locking in pm_runtime_put_suppliers() (Rafael Wysocki).
- Add safety net to supplier device release in the runtime PM core
code (Rafael Wysocki).
- Capture device status before disabling runtime PM for it (Rafael
Wysocki).
- Add new macros for declaring PM operations to allow drivers to
avoid guarding them with CONFIG_PM #ifdefs or __maybe_unused and
update some drivers to use these macros (Paul Cercueil).
- Allow ACPI hardware signature to be honoured during restore from
hibernation (David Woodhouse).
- Update outdated operating performance points (OPP) documentation
(Tang Yizhou).
- Reduce log severity for informative message regarding frequency
transition failures in devfreq (Tzung-Bi Shih).
- Add DRAM frequency controller devfreq driver for Allwinner sunXi
SoCs (Samuel Holland).
- Add missing COMMON_CLK dependency to sun8i devfreq driver (Arnd
Bergmann).
- Add support for new layout of Psys PowerLimit Register on SPR to
the Intel RAPL power capping driver (Zhang Rui).
- Fix typo in a comment in idle_inject.c (Jason Wang).
- Remove unused function definition from the DTPM (Dynamit Thermal
Power Management) power capping framework (Daniel Lezcano).
- Reduce DTPM trace verbosity (Daniel Lezcano)"
* tag 'pm-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (53 commits)
x86, sched: Fix undefined reference to init_freq_invariance_cppc() build error
cpufreq: amd-pstate: Fix Kconfig dependencies for AMD P-State
cpufreq: amd-pstate: Fix struct amd_cpudata kernel-doc comment
cpuidle: use default_groups in kobj_type
x86: intel_epb: Allow model specific normal EPB value
MAINTAINERS: Add AMD P-State driver maintainer entry
Documentation: amd-pstate: Add AMD P-State driver introduction
cpufreq: amd-pstate: Add AMD P-State performance attributes
cpufreq: amd-pstate: Add AMD P-State frequencies attributes
cpufreq: amd-pstate: Add boost mode support for AMD P-State
cpufreq: amd-pstate: Add trace for AMD P-State module
cpufreq: amd-pstate: Introduce the support for the processors with shared memory solution
cpufreq: amd-pstate: Add fast switch function for AMD P-State
cpufreq: amd-pstate: Introduce a new AMD P-State driver to support future processors
ACPI: CPPC: Add CPPC enable register function
ACPI: CPPC: Check present CPUs for determining _CPC is valid
ACPI: CPPC: Implement support for SystemIO registers
x86/msr: Add AMD CPPC MSR definitions
x86/cpufeatures: Add AMD Collaborative Processor Performance Control feature flag
cpufreq: use default_groups in kobj_type
...
Core
----
- Defer freeing TCP skbs to the BH handler, whenever possible,
or at least perform the freeing outside of the socket lock section
to decrease cross-CPU allocator work and improve latency.
- Add netdevice refcount tracking to locate sources of netdevice
and net namespace refcount leaks.
- Make Tx watchdog less intrusive - avoid pausing Tx and restarting
all queues from a single CPU removing latency spikes.
- Various small optimizations throughout the stack from Eric Dumazet.
- Make netdev->dev_addr[] constant, force modifications to go via
appropriate helpers to allow us to keep addresses in ordered data
structures.
- Replace unix_table_lock with per-hash locks, improving performance
of bind() calls.
- Extend skb drop tracepoint with a drop reason.
- Allow SO_MARK and SO_PRIORITY setsockopt under CAP_NET_RAW.
BPF
---
- New helpers:
- bpf_find_vma(), find and inspect VMAs for profiling use cases
- bpf_loop(), runtime-bounded loop helper trading some execution
time for much faster (if at all converging) verification
- bpf_strncmp(), improve performance, avoid compiler flakiness
- bpf_get_func_arg(), bpf_get_func_ret(), bpf_get_func_arg_cnt()
for tracing programs, all inlined by the verifier
- Support BPF relocations (CO-RE) in the kernel loader.
- Further the support for BTF_TYPE_TAG annotations.
- Allow access to local storage in sleepable helpers.
- Convert verifier argument types to a composable form with different
attributes which can be shared across types (ro, maybe-null).
- Prepare libbpf for upcoming v1.0 release by cleaning up APIs,
creating new, extensible ones where missing and deprecating those
to be removed.
Protocols
---------
- WiFi (mac80211/cfg80211):
- notify user space about long "come back in N" AP responses,
allow it to react to such temporary rejections
- allow non-standard VHT MCS 10/11 rates
- use coarse time in airtime fairness code to save CPU cycles
- Bluetooth:
- rework of HCI command execution serialization to use a common
queue and work struct, and improve handling errors reported
in the middle of a batch of commands
- rework HCI event handling to use skb_pull_data, avoiding packet
parsing pitfalls
- support AOSP Bluetooth Quality Report
- SMC:
- support net namespaces, following the RDMA model
- improve connection establishment latency by pre-clearing buffers
- introduce TCP ULP for automatic redirection to SMC
- Multi-Path TCP:
- support ioctls: SIOCINQ, OUTQ, and OUTQNSD
- support socket options: IP_TOS, IP_FREEBIND, IP_TRANSPARENT,
IPV6_FREEBIND, and IPV6_TRANSPARENT, TCP_CORK and TCP_NODELAY
- support cmsgs: TCP_INQ
- improvements in the data scheduler (assigning data to subflows)
- support fastclose option (quick shutdown of the full MPTCP
connection, similar to TCP RST in regular TCP)
- MCTP (Management Component Transport) over serial, as defined by
DMTF spec DSP0253 - "MCTP Serial Transport Binding".
Driver API
----------
- Support timestamping on bond interfaces in active/passive mode.
- Introduce generic phylink link mode validation for drivers which
don't have any quirks and where MAC capability bits fully express
what's supported. Allow PCS layer to participate in the validation.
Convert a number of drivers.
- Add support to set/get size of buffers on the Rx rings and size of
the tx copybreak buffer via ethtool.
- Support offloading TC actions as first-class citizens rather than
only as attributes of filters, improve sharing and device resource
utilization.
- WiFi (mac80211/cfg80211):
- support forwarding offload (ndo_fill_forward_path)
- support for background radar detection hardware
- SA Query Procedures offload on the AP side
New hardware / drivers
----------------------
- tsnep - FPGA based TSN endpoint Ethernet MAC used in PLCs with
real-time requirements for isochronous communication with protocols
like OPC UA Pub/Sub.
- Qualcomm BAM-DMUX WWAN - driver for data channels of modems
integrated into many older Qualcomm SoCs, e.g. MSM8916 or
MSM8974 (qcom_bam_dmux).
- Microchip LAN966x multi-port Gigabit AVB/TSN Ethernet Switch
driver with support for bridging, VLANs and multicast forwarding
(lan966x).
- iwlmei driver for co-operating between Intel's WiFi driver and
Intel's Active Management Technology (AMT) devices.
- mse102x - Vertexcom MSE102x Homeplug GreenPHY chips
- Bluetooth:
- MediaTek MT7921 SDIO devices
- Foxconn MT7922A
- Realtek RTL8852AE
Drivers
-------
- Significantly improve performance in the datapaths of:
lan78xx, ax88179_178a, lantiq_xrx200, bnxt.
- Intel Ethernet NICs:
- igb: support PTP/time PEROUT and EXTTS SDP functions on
82580/i354/i350 adapters
- ixgbevf: new PF -> VF mailbox API which avoids the risk of
mailbox corruption with ESXi
- iavf: support configuration of VLAN features of finer granularity,
stacked tags and filtering
- ice: PTP support for new E822 devices with sub-ns precision
- ice: support firmware activation without reboot
- Mellanox Ethernet NICs (mlx5):
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- support TC forwarding when tunnel encap and decap happen between
two ports of the same NIC
- dynamically size and allow disabling various features to save
resources for running in embedded / SmartNIC scenarios
- Broadcom Ethernet NICs (bnxt):
- use page frag allocator to improve Rx performance
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- Other Ethernet NICs:
- amd-xgbe: add Ryzen 6000 (Yellow Carp) Ethernet support
- Microsoft cloud/virtual NIC (mana):
- add XDP support (PASS, DROP, TX)
- Mellanox Ethernet switches (mlxsw):
- initial support for Spectrum-4 ASICs
- VxLAN with IPv6 underlay
- Marvell Ethernet switches (prestera):
- support flower flow templates
- add basic IP forwarding support
- NXP embedded Ethernet switches (ocelot & felix):
- support Per-Stream Filtering and Policing (PSFP)
- enable cut-through forwarding between ports by default
- support FDMA to improve packet Rx/Tx to CPU
- Other embedded switches:
- hellcreek: improve trapping management (STP and PTP) packets
- qca8k: support link aggregation and port mirroring
- Qualcomm 802.11ax WiFi (ath11k):
- qca6390, wcn6855: enable 802.11 power save mode in station mode
- BSS color change support
- WCN6855 hw2.1 support
- 11d scan offload support
- scan MAC address randomization support
- full monitor mode, only supported on QCN9074
- qca6390/wcn6855: report signal and tx bitrate
- qca6390: rfkill support
- qca6390/wcn6855: regdb.bin support
- Intel WiFi (iwlwifi):
- support SAR GEO Offset Mapping (SGOM) and Time-Aware-SAR (TAS)
in cooperation with the BIOS
- support for Optimized Connectivity Experience (OCE) scan
- support firmware API version 68
- lots of preparatory work for the upcoming Bz device family
- MediaTek WiFi (mt76):
- Specific Absorption Rate (SAR) support
- mt7921: 160 MHz channel support
- RealTek WiFi (rtw88):
- Specific Absorption Rate (SAR) support
- scan offload
- Other WiFi NICs
- ath10k: support fetching (pre-)calibration data from nvmem
- brcmfmac: configure keep-alive packet on suspend
- wcn36xx: beacon filter support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=KLm3
-----END PGP SIGNATURE-----
Merge tag '5.17-net-next' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core
----
- Defer freeing TCP skbs to the BH handler, whenever possible, or at
least perform the freeing outside of the socket lock section to
decrease cross-CPU allocator work and improve latency.
- Add netdevice refcount tracking to locate sources of netdevice and
net namespace refcount leaks.
- Make Tx watchdog less intrusive - avoid pausing Tx and restarting
all queues from a single CPU removing latency spikes.
- Various small optimizations throughout the stack from Eric Dumazet.
- Make netdev->dev_addr[] constant, force modifications to go via
appropriate helpers to allow us to keep addresses in ordered data
structures.
- Replace unix_table_lock with per-hash locks, improving performance
of bind() calls.
- Extend skb drop tracepoint with a drop reason.
- Allow SO_MARK and SO_PRIORITY setsockopt under CAP_NET_RAW.
BPF
---
- New helpers:
- bpf_find_vma(), find and inspect VMAs for profiling use cases
- bpf_loop(), runtime-bounded loop helper trading some execution
time for much faster (if at all converging) verification
- bpf_strncmp(), improve performance, avoid compiler flakiness
- bpf_get_func_arg(), bpf_get_func_ret(), bpf_get_func_arg_cnt()
for tracing programs, all inlined by the verifier
- Support BPF relocations (CO-RE) in the kernel loader.
- Further the support for BTF_TYPE_TAG annotations.
- Allow access to local storage in sleepable helpers.
- Convert verifier argument types to a composable form with different
attributes which can be shared across types (ro, maybe-null).
- Prepare libbpf for upcoming v1.0 release by cleaning up APIs,
creating new, extensible ones where missing and deprecating those
to be removed.
Protocols
---------
- WiFi (mac80211/cfg80211):
- notify user space about long "come back in N" AP responses,
allow it to react to such temporary rejections
- allow non-standard VHT MCS 10/11 rates
- use coarse time in airtime fairness code to save CPU cycles
- Bluetooth:
- rework of HCI command execution serialization to use a common
queue and work struct, and improve handling errors reported in
the middle of a batch of commands
- rework HCI event handling to use skb_pull_data, avoiding packet
parsing pitfalls
- support AOSP Bluetooth Quality Report
- SMC:
- support net namespaces, following the RDMA model
- improve connection establishment latency by pre-clearing buffers
- introduce TCP ULP for automatic redirection to SMC
- Multi-Path TCP:
- support ioctls: SIOCINQ, OUTQ, and OUTQNSD
- support socket options: IP_TOS, IP_FREEBIND, IP_TRANSPARENT,
IPV6_FREEBIND, and IPV6_TRANSPARENT, TCP_CORK and TCP_NODELAY
- support cmsgs: TCP_INQ
- improvements in the data scheduler (assigning data to subflows)
- support fastclose option (quick shutdown of the full MPTCP
connection, similar to TCP RST in regular TCP)
- MCTP (Management Component Transport) over serial, as defined by
DMTF spec DSP0253 - "MCTP Serial Transport Binding".
Driver API
----------
- Support timestamping on bond interfaces in active/passive mode.
- Introduce generic phylink link mode validation for drivers which
don't have any quirks and where MAC capability bits fully express
what's supported. Allow PCS layer to participate in the validation.
Convert a number of drivers.
- Add support to set/get size of buffers on the Rx rings and size of
the tx copybreak buffer via ethtool.
- Support offloading TC actions as first-class citizens rather than
only as attributes of filters, improve sharing and device resource
utilization.
- WiFi (mac80211/cfg80211):
- support forwarding offload (ndo_fill_forward_path)
- support for background radar detection hardware
- SA Query Procedures offload on the AP side
New hardware / drivers
----------------------
- tsnep - FPGA based TSN endpoint Ethernet MAC used in PLCs with
real-time requirements for isochronous communication with protocols
like OPC UA Pub/Sub.
- Qualcomm BAM-DMUX WWAN - driver for data channels of modems
integrated into many older Qualcomm SoCs, e.g. MSM8916 or MSM8974
(qcom_bam_dmux).
- Microchip LAN966x multi-port Gigabit AVB/TSN Ethernet Switch driver
with support for bridging, VLANs and multicast forwarding
(lan966x).
- iwlmei driver for co-operating between Intel's WiFi driver and
Intel's Active Management Technology (AMT) devices.
- mse102x - Vertexcom MSE102x Homeplug GreenPHY chips
- Bluetooth:
- MediaTek MT7921 SDIO devices
- Foxconn MT7922A
- Realtek RTL8852AE
Drivers
-------
- Significantly improve performance in the datapaths of: lan78xx,
ax88179_178a, lantiq_xrx200, bnxt.
- Intel Ethernet NICs:
- igb: support PTP/time PEROUT and EXTTS SDP functions on
82580/i354/i350 adapters
- ixgbevf: new PF -> VF mailbox API which avoids the risk of
mailbox corruption with ESXi
- iavf: support configuration of VLAN features of finer
granularity, stacked tags and filtering
- ice: PTP support for new E822 devices with sub-ns precision
- ice: support firmware activation without reboot
- Mellanox Ethernet NICs (mlx5):
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- support TC forwarding when tunnel encap and decap happen between
two ports of the same NIC
- dynamically size and allow disabling various features to save
resources for running in embedded / SmartNIC scenarios
- Broadcom Ethernet NICs (bnxt):
- use page frag allocator to improve Rx performance
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- Other Ethernet NICs:
- amd-xgbe: add Ryzen 6000 (Yellow Carp) Ethernet support
- Microsoft cloud/virtual NIC (mana):
- add XDP support (PASS, DROP, TX)
- Mellanox Ethernet switches (mlxsw):
- initial support for Spectrum-4 ASICs
- VxLAN with IPv6 underlay
- Marvell Ethernet switches (prestera):
- support flower flow templates
- add basic IP forwarding support
- NXP embedded Ethernet switches (ocelot & felix):
- support Per-Stream Filtering and Policing (PSFP)
- enable cut-through forwarding between ports by default
- support FDMA to improve packet Rx/Tx to CPU
- Other embedded switches:
- hellcreek: improve trapping management (STP and PTP) packets
- qca8k: support link aggregation and port mirroring
- Qualcomm 802.11ax WiFi (ath11k):
- qca6390, wcn6855: enable 802.11 power save mode in station mode
- BSS color change support
- WCN6855 hw2.1 support
- 11d scan offload support
- scan MAC address randomization support
- full monitor mode, only supported on QCN9074
- qca6390/wcn6855: report signal and tx bitrate
- qca6390: rfkill support
- qca6390/wcn6855: regdb.bin support
- Intel WiFi (iwlwifi):
- support SAR GEO Offset Mapping (SGOM) and Time-Aware-SAR (TAS)
in cooperation with the BIOS
- support for Optimized Connectivity Experience (OCE) scan
- support firmware API version 68
- lots of preparatory work for the upcoming Bz device family
- MediaTek WiFi (mt76):
- Specific Absorption Rate (SAR) support
- mt7921: 160 MHz channel support
- RealTek WiFi (rtw88):
- Specific Absorption Rate (SAR) support
- scan offload
- Other WiFi NICs
- ath10k: support fetching (pre-)calibration data from nvmem
- brcmfmac: configure keep-alive packet on suspend
- wcn36xx: beacon filter support"
* tag '5.17-net-next' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2048 commits)
tcp: tcp_send_challenge_ack delete useless param `skb`
net/qla3xxx: Remove useless DMA-32 fallback configuration
rocker: Remove useless DMA-32 fallback configuration
hinic: Remove useless DMA-32 fallback configuration
lan743x: Remove useless DMA-32 fallback configuration
net: enetc: Remove useless DMA-32 fallback configuration
cxgb4vf: Remove useless DMA-32 fallback configuration
cxgb4: Remove useless DMA-32 fallback configuration
cxgb3: Remove useless DMA-32 fallback configuration
bnx2x: Remove useless DMA-32 fallback configuration
et131x: Remove useless DMA-32 fallback configuration
be2net: Remove useless DMA-32 fallback configuration
vmxnet3: Remove useless DMA-32 fallback configuration
bna: Simplify DMA setting
net: alteon: Simplify DMA setting
myri10ge: Simplify DMA setting
qlcnic: Simplify DMA setting
net: allwinner: Fix print format
page_pool: remove spinlock in page_pool_refill_alloc_cache()
amt: fix wrong return type of amt_send_membership_update()
...
Merge cpuidle updates, PM core updates and one hiberation-related
update for 5.17-rc1:
- Make cpuidle use default_groups in kobj_type (Greg Kroah-Hartman).
- Fix two comments in cpuidle code (Jason Wang, Yang Li).
- Simplify locking in pm_runtime_put_suppliers() (Rafael Wysocki).
- Add safety net to supplier device release in the runtime PM core
code (Rafael Wysocki).
- Capture device status before disabling runtime PM for it (Rafael
Wysocki).
- Add new macros for declaring PM operations to allow drivers to
avoid guarding them with CONFIG_PM #ifdefs or __maybe_unused and
update some drivers to use these macros (Paul Cercueil).
- Allow ACPI hardware signature to be honoured during restore from
hibernation (David Woodhouse).
* pm-cpuidle:
cpuidle: use default_groups in kobj_type
cpuidle: Fix cpuidle_remove_state_sysfs() kerneldoc comment
cpuidle: menu: Fix typo in a comment
* pm-core:
PM: runtime: Simplify locking in pm_runtime_put_suppliers()
mmc: mxc: Use the new PM macros
mmc: jz4740: Use the new PM macros
PM: runtime: Add safety net to supplier device release
PM: runtime: Capture device status before disabling runtime PM
PM: core: Add new *_PM_OPS macros, deprecate old ones
PM: core: Redefine pm_ptr() macro
r8169: Avoid misuse of pm_ptr() macro
* pm-sleep:
PM: hibernate: Allow ACPI hardware signature to be honoured
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Moreover, dma_set_mask_and_coherent() returns 0 or -EIO, so the return
code of the function can be used directly.
Finally, inline bnx2x_set_coherency_mask() because it is now only a wrapper
for a single dma_set_mask_and_coherent() call.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/29608a525876afddceabf8f11b2ba606da8748fc.1641730747.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Moreover, dma_set_mask_and_coherent() returns 0 or -EIO, so the return
code of the function can be used directly. There is no need to 'rc = -EIO'
explicitly.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/b9aa46e7e5a5aa61f56aac5ea439930f41ad9946.1641726804.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So if dma_set_mask_and_coherent() succeeds, 'netdev->features' will have
NETIF_F_HIGHDMA in all cases. Move the assignment of this feature in
be_netdev_init() instead be_probe() which is a much logical place.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/637696d7141faa68c29fc34b70f9aa67d5e605f0.1641718999.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask will never fail if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So, if dma_set_mask_and_coherent() succeeds, 'using_dac' is known to be
'true'. This variable can be removed.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/1d5a7b3f4fa735f1233c3eb3fa07e71df95fad75.1641658516.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask will never fail if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
If dma_set_mask_and_coherent() succeeds, 'ap->pci_using_dac' is known to be
1. So 'pci_using_dac' can be removed from the 'struct ace_private'.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/1a414c05c27b21c661aef61dffe1adcd1578b1f5.1641651917.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask will never fail if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So qlcnic_set_dma_mask(), (in qlcnic_main.c) can be simplified a lot and
inlined directly in its only caller.
If dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be 1.
So it can be removed from all the calling chain.
qlcnic_setup_netdev() can finally be simplified as-well.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/4996ab0337d62ec6a54b2edf234cd5ced4b4d7ad.1641649611.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kees reports quoted commit introduced the following warning on arm64:
drivers/net/ethernet/allwinner/sun4i-emac.c:922:60: error: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
922 | netdev_info(ndev, "get io resource from device: 0x%x, size = %u\n",
| ~^
| | | unsigned int
| %llx
923 | regs->start, resource_size(regs));
| ~~~~~~~~~~~
| |
| resource_size_t {aka long long unsigned int}
.. and another one like that for resource_size().
Switch to %pa and a cast.
Reported-by: Kees Cook <keescook@chromium.org>
Fixes: 47869e82c8 ("sun4i-emac.c: add dma support")
Link: https://lore.kernel.org/r/20220108034438.2227343-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
amt_send_membership_update() would return -1 but it's return type is bool.
So, it should be used TRUE instead of -1.
Fixes: cbc21dc1cf ("amt: add data plane of amt interface")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://lore.kernel.org/r/20220109163702.6331-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Syzbot reported uninit value in mcs7830_bind(). The problem was in
missing validation check for bytes read via usbnet_read_cmd().
usbnet_read_cmd() internally calls usb_control_msg(), that returns
number of bytes read. Code should validate that requested number of bytes
was actually read.
So, this patch adds missing size validation check inside
mcs7830_get_reg() to prevent uninit value bugs
Reported-and-tested-by: syzbot+003c0a286b9af5412510@syzkaller.appspotmail.com
Fixes: 2a36d70834 ("USB: driver for mcs7830 (aka DeLOCK) USB ethernet adapter")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220106225716.7425-1-paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Build bot reports:
drivers/net/ethernet/mellanox/mlx5/core/en_stats.c: In function 'fec_set_block_stats':
drivers/net/ethernet/mellanox/mlx5/core/en_stats.c:1235:48: error: 'outl' undeclared (first use in this function); did you mean 'out'?
1235 | if (mlx5_core_access_reg(mdev, in, sz, outl, sz, MLX5_REG_PPCNT, 0, 0))
| ^~~~
| out
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20220109213321.2292830-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While it has always been possible to infer that an HWRM command was
abandoned due to an unhealthy firmware status by the shortened timeout
reported, this change improves the log messaging to account for this
case explicitly. In the interests of further clarity, the firmware
status is now also reported in these new messages.
v2: Remove inline keyword for hwrm_wait_must_abort() in .c file.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some older devices cannot accommodate the 40 seconds timeout
cap for long running commands (such as NVRAM commands) due to
hardware limitations. Allow these devices to request more time for
these long running commands, but print a warning, since the longer
timeout may cause the hung task watchdog to trigger. In the case of a
firmware update operation, this is preferable to failing outright.
v2: Use bp->hwrm_cmd_max_timeout directly without the constants.
Fixes: 881d8353b0 ("bnxt_en: Add an upper bound for all firmware command timeouts.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current driver design relies on the PF netdev being open in order
to intercept the following HWRM commands from a VF:
- HWRM_FUNC_VF_CFG
- HWRM_CFA_L2_FILTER_ALLOC
- HWRM_PORT_PHY_QCFG (only if FW_CAP_LINK_ADMIN is not supported)
If the PF is closed, then VFs are subjected to rather inscrutable error
messages in response to any configuration requests involving the above
command types. Recent firmware distinguishes this problem case from
other errors by returning HWRM_ERR_CODE_PF_UNAVAILABLE. In most cases,
the appropriate course of action is still to fail, but this can now be
accomplished with the aid of more user informative log messages. For L2
filter allocations that are already asynchronous, an automatic retry
seems more appropriate.
v2: Delete extra newline.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add logging of firmware messages. These can be useful for diagnosing
issues in the field, but due to their verbosity are only appropriate
at a debug message level.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When building ARCH=arm allmodconfig:
drivers/net/wireless/intel/iwlwifi/mvm/ftm-initiator.c: In function ‘iwl_mvm_ftm_rtt_smoothing’:
./include/asm-generic/div64.h:222:35: error: comparison of distinct pointer types lacks a cast [-Werror]
222 | (void)(((typeof((n)) *)0) == ((uint64_t *)0)); \
| ^~
drivers/net/wireless/intel/iwlwifi/mvm/ftm-initiator.c:1070:9: note: in expansion of macro ‘do_div’
1070 | do_div(rtt_avg, 100);
| ^~~~~~
do_div() has to be used with an unsigned 64-bit integer dividend but
rtt_avg is a signed 64-bit integer.
div_s64() expects a signed 64-bit integer dividend and signed 32-bit
divisor, which fits this scenario, so use that function here to fix the
warning.
Fixes: 8b0f92549f ("iwlwifi: mvm: fix 32-bit build in FTM")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211227191757.2354329-1-nathan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
No information is deliberately sent in hf->flags in host -> device
communications, but the open-source candleLight firmware echoes it
back, which can result in the GS_CAN_FLAG_OVERFLOW flag being set and
generating spurious ERRORFRAMEs.
While there also initialize the reserved member with 0.
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20220106002952.25883-1-brian.silverman@bluerivertech.com
Link: https://github.com/candle-usb/candleLight_fw/issues/87
Cc: stable@vger.kernel.org
Signed-off-by: Brian Silverman <brian.silverman@bluerivertech.com>
[mkl: initialize the reserved member, too]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make sure we free CAN network device in the error path. There are
several jumps to fail label after allocating the CAN network device
successfully. This patch places the free_candev() under fail label so
that in failure path a jump to fail label frees the CAN network
device.
Fixes: 76e9353a80 ("can: rcar_canfd: Add support for RZ/G2L family")
Link: https://lore.kernel.org/all/20220106114801.20563-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq()
effectively convert that into -EINVAL, even at probe time rather than
later on. So it might be better to check just now.
Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Link: https://lore.kernel.org/all/20211224021324.1447494-1-jiasheng@iscas.ac.cn
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the function softing_startstop() the variable error_reporting is
assigned but not used. The code that uses this variable is commented
out. Its stated that the functionality is not finally verified.
To fix the warning:
| drivers/net/can/softing/softing_fw.c:424:9: error: variable 'error_reporting' set but not used [-Werror,-Wunused-but-set-variable]
remove the comment, activate the code, but add a "0 &&" to the if
expression and rely on the optimizer rather than the preprocessor to
remove the code.
Link: https://lore.kernel.org/all/20220109103126.1872833-1-mkl@pengutronix.de
Fixes: 03fd3cf5a1 ("can: add driver for Softing card")
Cc: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case device registration fails during probe, the driver state and
the embedded platform device structure needs to be freed using
platform_device_put() to properly free all resources (e.g. the device
name).
Fixes: 0a0b7a5f7a ("can: add driver for Softing card")
Link: https://lore.kernel.org/all/20211222104843.6105-1-johan@kernel.org
Cc: stable@vger.kernel.org # 2.6.38
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds ethtool support to get the number of message buffers
configured for reception/transmission, which may also depends on
runtime configurations such as the 'rx-rtr' flag state.
Link: https://lore.kernel.org/all/20220108181633.420433-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
[mkl: port to net-next/master, replace __sw_hweight64 by simpler calculation]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a private flag to the flexcan driver to switch the
"rx-rtr" setting on and off.
"rx-rtr" on - Receive RTR frames. (default)
The CAN controller can and will receive RTR frames.
On some IP cores the controller cannot receive RTR
frames in the more performant "RX mailbox" mode and
will use "RX FIFO" mode instead.
"rx-rtr" off - Waive ability to receive RTR frames. (not supported on all IP cores)
This mode activates the "RX mailbox mode" for better
performance, on some IP cores RTR frames cannot be
received anymore.
The "RX FIFO" mode uses a FIFO with a depth of 6 CAN frames.
The "RX mailbox" mode uses up to 62 mailboxes.
Link: https://lore.kernel.org/all/20220107193105.1699523-6-mkl@pengutronix.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Co-developed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Most flexcan IP cores support 2 RX modes:
- FIFO
- mailbox
Some IP core versions cannot receive CAN RTR messages via mailboxes.
This patch adds quirks to document this.
This information will be used in a later patch to switch from FIFO to
more performant mailbox mode at the expense of losing the ability to
receive RTR messages. This trade off is beneficial in certain use
cases.
Link: https://lore.kernel.org/all/20220107193105.1699523-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Most flexcan IP cores support 2 RX modes:
- FIFO
- mailbox
The names for these modes were chosen to reflect the name of the
rx-offload mode they are using.
The name of the RX modes should better reflect their difference with
regards the flexcan IP core. So this patch renames the various
occurrences of OFF_FIFO to RX_FIFO and OFF_TIMESTAMP to RX_MAILBOX:
| FLEXCAN_TX_MB_RESERVED_OFF_FIFO -> FLEXCAN_TX_MB_RESERVED_RX_FIFO
| FLEXCAN_TX_MB_RESERVED_OFF_TIMESTAMP -> FLEXCAN_TX_MB_RESERVED_RX_MAILBOX
| FLEXCAN_QUIRK_USE_OFF_TIMESTAMP -> FLEXCAN_QUIRK_USE_RX_MAILBOX
Link: https://lore.kernel.org/all/20220107193105.1699523-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
