Don't populate various arrays on the stack but instead make them
static const. Also makes the object code smaller by a few hundred
bytes.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211129224236.506883-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These are only assigned to the ops fields in the snd_soc_dai_link struct
which is a pointer to const struct snd_soc_ops. Make them const to allow
the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211127091954.12075-1-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On my T14s Gen2 I saw the following:
[ 16.057258] skl_hda_dsp_generic skl_hda_dsp_generic: hda_dsp_hdmi_build_controls: no PCM in topology for HDMI converter 3
[ 16.057261] skl_hda_dsp_generic skl_hda_dsp_generic: hda_dsp_hdmi_build_controls: no PCM in topology for HDMI converter 4
[ 16.057263] skl_hda_dsp_generic skl_hda_dsp_generic: hda_dsp_hdmi_build_controls: no PCM in topology for HDMI converter 5
[...and so on.]
It looks like the double newline is a mistake, so remove one.
Signed-off-by: Chris Down <chris@chrisdown.name>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/YaOS0sBueAfApwOx@chrisdown.name
Signed-off-by: Mark Brown <broonie@kernel.org>
These are only assigned to the ops field in the snd_soc_dai_link which
is a pointer to const struct snd_soc_ops. Make them const to allow the
compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20211127093147.17368-1-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On the latest Lenovo Thinkstation laptops, we often experience the
speaker failure after rebooting, check the dmesg, we could see:
sof-audio-pci-intel-tgl 0000:00:1f.3: codec #0 probe error, ret: -5
The analogue codec on the machine is ALC287, then we designed a
testcase to reboot and check the codec probing result repeatedly, we
found the analogue codec probing always failed at least once within
several minutes to several hours (roughly 1 reboot per min). This
issue happens on all laptops of this Thinkstation model, but with
legacy HDA driver, we couldn't reproduce this issue on those laptops.
And so far, this issue is not reproduced on machines which don't
belong to this model.
We tried to make the hda_dsp_ctrl_init_chip() same as
hda_intel_init_chip() which is the controller init routine in the
legacy HDA driver, but it didn't help.
We found when issue happens, the resp is -1, and if we let driver
re-run send_cmd() and get_response(), it will get the correct response
10ec0287, then driver continues the rest work, finally boot to the
desktop and all audio function work well.
Here adding codec probing retries to 3 times, it could fix the issue
on this Thinkstation model, and it doesn't bring impact to other
machines.
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211130090606.529348-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The "index" is potentially used without being initialized on the error
path.
Fixes: fc329c1de4 ("ASoC: amd: add platform devices for acp6x pdm driver and dmic driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211130125633.GA24941@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously, the DAI template was used directly, which lead to
fun bugs such as "why is my channels_max changing?" when one
instantiated more than one i2s_tdm IP block in a device tree.
This change makes it so that we instead duplicate the template
struct, and then use that.
Fixes: 081068fd64 ("ASoC: rockchip: add support for i2s-tdm controller")
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20211125084900.417102-1-frattaroli.nicolas@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:
Current soc_pcm_pointer() is checking runtime->delay,
but it might be updated silently by component's .point callback.
It is strange and difficult to find/know the issue. This patch
adds .delay callback for component, and solve the issue.
HDA uses a timecounter to read a hardware clock running at 24 MHz. The
conversion factor is set with a mult value of 125 and a shift value of 0,
which is not converting the hardware clock to nanoseconds, it is converting
to 1/3 nanoseconds because the conversion factor from 24Mhz to nanoseconds
is 125/3. The usage sites divide the "nanoseconds" value returned by
timecounter_read() by 3 to get a real nanoseconds value.
There is a lengthy comment in azx_timecounter_init() explaining this
choice. That comment makes blatantly wrong assumptions about how
timecounters work and what can overflow.
The comment says:
* Applying the 1/3 factor as part of the multiplication
* requires at least 20 bits for a decent precision, however
* overflows occur after about 4 hours or less, not a option.
timecounters operate on time deltas between two readouts of a clock and use
the mult/shift pair to calculate a precise nanoseconds value:
delta_nsec = (delta_clock * mult) >> shift;
The fractional part is also taken into account and preserved to prevent
accumulated rounding errors. For details see cyclecounter_cyc2ns().
The mult/shift pair has to be chosen so that the multiplication of the
maximum expected delta value does not result in a 64bit overflow. As the
counter wraps around on 32bit, the maximum observable delta between two
reads is (1 << 32) - 1 which is about 178.9 seconds.
That in turn means the maximum multiplication factor which fits into an u32
will not cause a 64bit overflow ever because it's guaranteed that:
((1 << 32) - 1) ^ 2 < (1 << 64)
The resulting correct multiplication factor is 2796202667 and the shift
value is 26, i.e. 26 bit precision. The overflow of the multiplication
would happen exactly at a clock readout delta of 6597069765 which is way
after the wrap around of the hardware clock at around 274.8 seconds which
is off from the claimed 4 hours by more than an order of magnitude.
If the counter ever wraps around the last read value then the calculation
is off by the number of wrap arounds times 178.9 seconds because the
overflow cannot be observed.
Use clocks_calc_mult_shift(), which calculates the most accurate mult/shift
pair based on the given clock frequency, and remove the bogus comment along
with the divisions at the readout sites.
Fixes: 5d890f591d ("ALSA: hda: support for wallclock timestamps")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/871r35kwji.ffs@tglx
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Qcom machine driver adds rt5682s support in this patch.
Card name can be specified from dts by model property, and driver makes
use of the name to distinguish which headset codec is on the board.
Signed-off-by: lvzhaoxiong <lvzhaoxiong@huaqin.corp-partner.google.com>
Link: https://lore.kernel.org/r/20211123024329.21998-1-lvzhaoxiong@huaqin.corp-partner.google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows changing the volume of each digital input/output
independently, and provides the only "master volume" for the DAC.
(The ADC also has a gain control on the analog side.)
While the hardware supports digital gain up to +72dB, the controls here
are limited to +24dB maximum, as any gain above that level makes volume
sliders difficult to use, and is extremely likely to cause clipping.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20211118033645.43524-1-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Now ALSA SoC supports .delay for component.
This patch uses it, and not update runtime->delay on .pointer
directly / secretly.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/871r3gy25j.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now ALSA SoC supports .delay for component.
This patch uses it, and not update runtime->delay on .pointer
directly / secretly.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/8735nwy25o.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current soc-pcm.c :: soc_pcm_pointer() is assuming that
component driver might update runtime->delay silently in
snd_soc_pcm_component_pointer() (= A).
static snd_pcm_uframes_t soc_pcm_pointer(...)
{
...
/* clearing the previous total delay */
=> runtime->delay = 0;
(A) offset = snd_soc_pcm_component_pointer(substream);
/* base delay if assigned in pointer callback */
=> delay = runtime->delay;
...
}
1) The behavior that ".pointer callback secretly updates
runtime->delay" is strange and confusable.
2) Current snd_soc_pcm_component_pointer() uses 1st found component's
.pointer callback only, thus it is no problem for now.
But runtime->delay might be overwrote if it adjusted to multiple
components in the future.
3) Component delay is updated at .pointer callback timing (secretly).
But some components which doesn't have .pointer callback might want
to increase runtime->delay for some reasons.
We already have .delay function for DAI, but not have for Component.
This patch adds new snd_soc_pcm_component_delay() for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/874k8cy25t.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current soc_pcm_pointer() is manually calculating
both CPU-DAI's max delay (= A)
and Codec-DAI's max delay (= B).
static snd_pcm_uframes_t soc_pcm_pointer(...)
{
...
^ for_each_rtd_cpu_dais(rtd, i, cpu_dai)
(A) cpu_delay = max(cpu_delay, ...);
v delay += cpu_delay;
^ for_each_rtd_codec_dais(rtd, i, codec_dai)
(B) codec_delay = max(codec_delay, ...);
v delay += codec_delay;
runtime->delay = delay;
...
}
Current soc_pcm_pointer() and the total delay calculating
is not readable / difficult to understand.
This patch update snd_soc_dai_delay() to snd_soc_pcm_dai_delay(),
and calcule both CPU/Codec delay in one function.
Link: https://lore.kernel.org/r/87fszl4yrq.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/875yssy25z.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For cs8409, it is required to run Jack Detect on resume.
Jack Detect on cs8409+cs42l42 requires an interrupt from
cs42l42 to be sent to cs8409 which is propogated to the driver
via an unsolicited event.
However, the hda_codec drops unsolicited events if the power_state
is not set to PMSG_ON. Which is set at the end of the resume call.
This means there is a race condition between setting power_state
to PMSG_ON and receiving the interrupt.
To solve this, we can add an API to set the power_state earlier
and call that before we start Jack Detect.
This does not cause issues, since we know inside our driver that
we are already initialized, and ready to handle the unsolicited
events.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Cc: <stable@vger.kernel.org> # v5.15+
Link: https://lore.kernel.org/r/20211128115558.71683-1-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Kai Vehmanen <kai.vehmanen@linux.intel.com>:
Implement an updated programming sequence to handle DMA stop for Intel
HD-Audio DMA.
The new flow is only used if the firmware is sufficiently new to
support the feature. SOF1.9.2 is the first release with the updated
flow. The kernel changes are backwards compatible with old firmware
releases. Likewise new firmware releases will work with old kernel.
Series reviewed originally at:
https://github.com/thesofproject/linux/pull/3167
Merge series from Sameer Pujar <spujar@nvidia.com>:
This series addresses following problems:
* The runtime PM is not balanced in MVC driver, whenever
mute or volume mixer controls are set.
* Some of the AHUB devices (SFC, MVC, Mixer, AMX and ADX)
use late system sleep. Suspend failure is seen on Jetson
TX2 platform.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYaD8mwAKCRCAXGG7T9hj
vspAAPwLA5SUorji33PTetwmcpLcoRJ3Q4HAPz+bOPdm9iL/PgD/V8MtxFrFebBs
AJoa+GmBarUNn7XCqKnCcA64iXhrpQw=
=6GY3
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.16c-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- Kconfig fix to make it possible to control building of the privcmd
driver
- three fixes for issues identified by the kernel test robot
- a five-patch series to simplify timeout handling for Xen PV driver
initialization
- two patches to fix error paths in xenstore/xenbus driver
initialization
* tag 'for-linus-5.16c-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: make HYPERVISOR_set_debugreg() always_inline
xen: make HYPERVISOR_get_debugreg() always_inline
xen: detect uninitialized xenbus in xenbus_init
xen: flag xen_snd_front to be not essential for system boot
xen: flag pvcalls-front to be not essential for system boot
xen: flag hvc_xen to be not essential for system boot
xen: flag xen_drm_front to be not essential for system boot
xen: add "not_essential" flag to struct xenbus_driver
xen/pvh: add missing prototype to header
xen: don't continue xenstore initialization in case of errors
xen/privcmd: make option visible in Kconfig
On 32-bit with CONFIG_ARCH_DMA_ADDR_T_64BIT=n:
sound/soc/sof/mediatek/mt8195/mt8195.c: In function ‘platform_parse_resource’:
sound/soc/sof/mediatek/mt8195/mt8195.c:51:15: error: format ‘%llx’ expects argument of type ‘long long unsigned int’, but argument 4 has type ‘unsigned int’ [-Werror=format=]
51 | dev_dbg(dev, "DMA pbase=0x%llx, size=0x%llx\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sound/soc/sof/mediatek/mt8195/mt8195.c: In function ‘adsp_memory_remap_init’:
sound/soc/sof/mediatek/mt8195/mt8195.c:167:15: error: format ‘%llx’ expects argument of type ‘long long unsigned int’, but argument 4 has type ‘phys_addr_t’ {aka ‘unsigned int’} [-Werror=format=]
167 | dev_dbg(dev, "adsp->pa_dram %llx, offset %#x\n", adsp->pa_dram, offset);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sound/soc/sof/mediatek/mt8195/mt8195.c: In function ‘adsp_shared_base_ioremap’:
sound/soc/sof/mediatek/mt8195/mt8195.c:196:15: error: format ‘%llx’ expects argument of type ‘long long unsigned int’, but argument 5 has type ‘phys_addr_t’ {aka ‘unsigned int’} [-Werror=format=]
196 | dev_dbg(dev, "shared-dram vbase=%p, phy addr :%llx, size=%#x\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix the first cases by printing the full resource using %pR.
Fix the other cases by printing the physical addresses using %pa.
Reported-by: noreply@ellerman.id.au
Fixes: 32d7e03d26 ("ASoC: SOF: mediatek: Add mt8195 hardware support")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211123103013.73645-1-geert@linux-m68k.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Can't link I2C and SPI to the same binary, better
to move CS35L41 to 3 modules approach.
And instead of exposing cs35l41_reg, volatile_reg,
readable_reg and precious_reg arrays, move
cs35l41_regmap_i2c/spi to new module and expose it.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211125143501.7720-1-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The capture and playback paths both have a configurable gain after their
respective mixer, which can be set from -31 dB to 0 dB in 32 steps.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20211125232543.117074-1-paul@crapouillou.net
Signed-off-by: Mark Brown <broonie@kernel.org>
This was found by coccicheck:
./sound/soc/fsl/imx-hdmi.c,209,1-7,ERROR missing put_device; call
of_find_device_by_node on line 119, but without a corresponding object
release within this function.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Link: https://lore.kernel.org/r/20211110002910.134915-1-ye.guojin@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
For HDA DAI's the DMA must be paused after the RUN bit is cleared by the
host. So, send the DAI_CONFIG IPC with just the SOF_DAI_CONFIG_FLAGS_PAUSE
flag set to indicate this to the firmware.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211125101520.291581-11-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some DAI components, such as HDaudio, need to be stopped in two steps
a) stop the DAI component
b) stop the DAI DMA
This patch enables this two-step stop by expanding the DAI_CONFIG
IPC flags and split them into 2 parts.
The 4 LSB bits indicate when the DAI_CONFIG IPC is sent, ex: hw_params,
hw_free or pause. The 4 MSB bits are used as the quirk flags to be used
along with the command flags. The quirk flag called
SOF_DAI_CONFIG_FLAGS_2_STEP_STOP shall be set along with the HW_PARAMS
command flag, i.e. before the pipeline is started so that the stop/pause
trigger op in the FW can take the appropriate action to either
perform/skip the DMA stop. If set, the DMA stop will be executed when
the DAI_CONFIG IPC is sent during hw_free. In the case of pause, DMA
pause will be handled when the DAI_CONFIG IPC is sent with the PAUSE
command flag.
Along with this, modify the signature for the hda_ctrl_dai_widget_setup/
hda_ctrl_dai_widget_free() functions to take additional flags as an
argument and modify all users to pass the appropriate quirk flags. Only
the HDA DAI's need to pass the SOF_DAI_CONFIG_FLAGS_2_STEP_STOP quirk
flag during hw_params to indicate that it supports two-step stop and
pause.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211125101520.291581-10-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Even though the order of stopping the DMA and freeing the widget list is
not important, align the sequence to match with the stop trigger to
avoid confusion.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211125101520.291581-9-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the check for the prepared flag inside snd_pcm_dsp_pcm_free() to
avoid having to check it before every invocation of the function.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211125101520.291581-8-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a helper function to free PCM in the FW, stop the DMA and free the
widget list. These actions are performed both during PCM trigger STOP
and when a paused stream is freed during system suspend.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211125101520.291581-7-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Paused streams must be stopped and platform hw_free should be invoked
during system suspend so they can be restarted properly after system
resume.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211125101520.291581-6-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_sof_pcm_platform_hw_params() will be called when the stream is
restarted with a prepare ioctl. This happens in two cases i.e. when a
suspended stream is resumed or when a stream is restarted without
intermediate call to sof_pcm_hw_free(). Make sure to call
snd_sof_pcm_platform_hw_free() in both these cases to keep it balanced.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211125101520.291581-5-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The recommended programming sequence for HD-Audio DMA is to reset the
stream before coupling the link and host DMA's.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211125101520.291581-4-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a helper function to perform stream reset.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211125101520.291581-3-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI_CONFIG IPC that is sent during the STOP trigger is used for
stopping the DMA in the FW. This must be done after the DMA RUN bit is
cleared by the host. So move the call to snd_hdac_ext_link_stream_clear()
before hda_link_dai_widget_update() to follow the correct programming
sequence for DMA stop for HDA DAIs.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211125101520.291581-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the declaration of temporary arrays to somewhere that won't go out
of scope before the devm_clk_hw_register() call, lest we be at the whim
of the compiler for whether those stack variables get overwritten.
Fixes a crash seen with gcc version 11.2.1 20210728 (Red Hat 11.2.1-1)
Fixes: bdd229ab26 ("ASoC: rt5682s: Add driver for ALC5682I-VS codec")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211118010453.843286-2-robdclark@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the declaration of temporary arrays to somewhere that won't go out
of scope before the devm_clk_hw_register() call, lest we be at the whim
of the compiler for whether those stack variables get overwritten.
Fixes a crash seen with gcc version 11.2.1 20210728 (Red Hat 11.2.1-1)
Fixes: edbd24ea1e ("ASoC: rt5682: Drop usage of __clk_get_name()")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211118010453.843286-1-robdclark@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver currently subscribes for a late system sleep call.
The initcall_debug log shows that suspend call for ADX device
happens after the parent device (AHUB). This seems to cause
suspend failure on Jetson TX2 platform. Also there is no use
of having late system sleep specifically for ADX device. Fix
the order by using normal system sleep.
Fixes: a99ab6f395 ("ASoC: tegra: Add Tegra210 based ADX driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1637676459-31191-7-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver currently subscribes for a late system sleep call.
The initcall_debug log shows that suspend call for AMX device
happens after the parent device (AHUB). This seems to cause
suspend failure on Jetson TX2 platform. Also there is no use
of having late system sleep specifically for AMX device. Fix
the order by using normal system sleep.
Fixes: 77f7df346c ("ASoC: tegra: Add Tegra210 based AMX driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1637676459-31191-6-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver currently subscribes for a late system sleep call.
The initcall_debug log shows that suspend call for Mixer device
happens after the parent device (AHUB). This seems to cause
suspend failure on Jetson TX2 platform. Also there is no use
of having late system sleep specifically for Mixer device. Fix
the order by using normal system sleep.
Fixes: 05bb3d5ec6 ("ASoC: tegra: Add Tegra210 based Mixer driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1637676459-31191-5-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver currently subscribes for a late system sleep call.
The initcall_debug log shows that suspend call for MVC device
happens after the parent device (AHUB). This seems to cause
suspend failure on Jetson TX2 platform. Also there is no use
of having late system sleep specifically for MVC device. Fix
the order by using normal system sleep.
Fixes: e539891f96 ("ASoC: tegra: Add Tegra210 based MVC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1637676459-31191-4-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver currently subscribes for a late system sleep call.
The initcall_debug log shows that suspend call for SFC device
happens after the parent device (AHUB). This seems to cause
suspend failure on Jetson TX2 platform. Also there is no use
of having late system sleep specifically for SFC device. Fix
the order by using normal system sleep.
Fixes: b2f74ec53a ("ASoC: tegra: Add Tegra210 based SFC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1637676459-31191-3-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After successful application of volume/mute settings via mixer control
put calls, the control returns without balancing the runtime PM count.
This makes device to be always runtime active. Fix this by allowing
control to reach pm_runtime_put() call.
Fixes: e539891f96 ("ASoC: tegra: Add Tegra210 based MVC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1637676459-31191-2-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There's a large but repetitive set of fixes here for issues with the
Tegra kcontrols not correctly reporting changes to userspace, a fix for
some issues with matching on older x86 platforms introduced during the
merge window together with a set of smaller fixes and one new system
quirk.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmGfjyoACgkQJNaLcl1U
h9C4Rgf/fXw9hh2Z/lInp08+RTZ/0NHcluiCk6ku7w0ATF0RsvvDl7kwkg9893ID
Zm0H+L1kiSMiOXy+uZGyAM2EpXU/m+R4JDi+nKONcJg/PIFeK7t13Tzu/J1NYF3h
e2r5GXyLpXJC4en8EuA/OJm3w8thdOm0Qrindpw2Sgc13JJCGtlQOw08f6kAidX0
58kbBMZB5Ofet9L4LMRWNt5fRgMzP25j0GOFQt9ujwddl6Pod0aOz+zfkNF+loCW
wb1FpqoeJkANfkKEtopYhKu7uK7XsU727jL6tXVnBz7PKkcVrKWCu1Iek3YbT89u
LAmfbiMtxKI380H9hEHUZ3YgMrRSDg==
=ngct
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.16-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.16
There's a large but repetitive set of fixes here for issues with the
Tegra kcontrols not correctly reporting changes to userspace, a fix for
some issues with matching on older x86 platforms introduced during the
merge window together with a set of smaller fixes and one new system
quirk.
Commit 0454422288 ("ASoC: codecs: wcd938x: add audio routing and
Kconfig") adds SND_SOC_WCD937X, which does not exist, and
SND_SOC_WCD938X, which seems not really to be the intended config to be
selected, but only a supporting config symbol to the actual config
SND_SOC_WCD938X_SDW for the codec.
Add SND_SOC_WCD938_SDW to the list instead of SND_SOC_WCD93{7,8}X.
The issue was identified with ./scripts/checkkconfigsymbols.py.
Fixes: 0454422288 ("ASoC: codecs: wcd938x: add audio routing and Kconfig")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20211125095158.8394-3-lukas.bulwahn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit f37fe2f998 ("ASoC: uniphier: add support for UniPhier AIO common
driver") adds configs SND_SOC_UNIPHIER_{LD11,PXS2}, which select the
non-existing config SND_SOC_UNIPHIER_AIO_DMA.
Hence, ./scripts/checkkconfigsymbols.py warns:
SND_SOC_UNIPHIER_AIO_DMA
Referencing files: sound/soc/uniphier/Kconfig
Probably, there is actually no further config intended to be selected
here. So, just drop selecting the non-existing config.
Fixes: f37fe2f998 ("ASoC: uniphier: add support for UniPhier AIO common driver")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20211125095158.8394-2-lukas.bulwahn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The node pointer is returned by of_parse_phandle() with
refcount incremented in platform_parse_resource(). Calling
of_node_put() to aovid the refcount leak.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211125071608.3056715-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The unnecessary conditional inclusion caused the following warning.
Such as:
>> sound/soc/mediatek/mt8192/mt8192-afe-pcm.c:2368:32: warning: unused
>> variable 'mt8192_afe_pm_ops' [-Wunused-const-variable]
static const struct dev_pm_ops mt8192_afe_pm_ops = {
Because runtime_pm already handles the case without CONFIG_PM, we
can remove CONFIG_PM condition.
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20211125042422.2349-1-jiaxin.yu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
The use of the SPIB register helps reduce power consumption - though
to a smaller degree than DMI_L1. This hardware capability is however
incompatible with userspace-initiated rewinds typically used by
PulseAudio.
In the past (2015..2017) Intel suggested an API extension to let
applications disable rewinds. At the time the feedback was that such a
capability was too Intel-specific and SPIB remained unused except for
loading DSP code. We now see devices with smaller batteries being
released, and it's time to revisit Linux support for SPIB to extend
battery life.
In this update the rewinds are disabled via an opt-in kernel
parameter. In the previous reviews, there was consensus that a Kconfig
option was too complicated for distributions to set, and we are
missing a TBD API to expose such capabilities to user-space.
The debate on whether or not to use rewinds, and the impact of
disabling rewinds, will likely be closed when Intel releases the
'deep-buffer' support, currently under development [2][3]. With this
solution, rewinds will not be needed, ever. When an application deals
with content that is not latency-sensitive (e.g. music playback), it
will be able to reduce power consumption by selecting a different PCM
device with increased buffering capabilities. Low-latency streams
will be handled by the 'regular' path. In other words, the impossible
compromise between power and latency will be handled with different
PCM devices/profiles for the same endpoint, and we can push the design
of capability negotiation to a later time when all the building blocks
(firmware topology, kernel, userspace) are ready - we still have
firmware xruns, DPCM race conditions to solve, and a need to describe
these alternate PCM devices with UCM using 'modifiers'.
