[Why]
Needs more frames waiting before the PSR_Exit sending for the specific
TCON.
[How]
Add relock_delay_frame_cnt to control how many frames waiting are needed
before the PSR_Exit sending. The default value is 0. The Driver side can
set this variable for specific TCONs.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Ryan Lin <tsung-hua.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[HOW&WHY]
Checking if both DSC and FEC supported from sink and
source before going with TPS3 pattern during link
training.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Iswara Nagulendran <iswara.nagulendran@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The Sink device string ID1/ID2 use 5 bytes instead of 6 bytes,
so the driver should compare the first 5 bytes only.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Robin Chen <po-tchen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSR-SU Rate Control - or PSR-SU-RC - enables PSR-SU panels to work with
variable refresh rate to allow for more power savings. Lowering the
refresh rate can increase PSR residency by expanding the eDP main link
shut down duration. It can also lower panel power consumption.
There is a complication with PSR, since the eDP main link can be shut
down. Therefore, the timing controller (TCON) on the eDP sink nees to be
able to scan out its remote buffer independent of the main link. To
allow the eDP source to specify the sink's refresh rate while the link
is off, vendor-specific DPCD registers are used. This allows the eDP
source to then "Rate Control" the panel during PSR active.
[How]
Add DC support to communicate with PSR-SU-RC supported eDP sinks. The
sink will need to know the desired VTotal during PSR active.
This change only adds support to DC, support in amdgpu_dm is still
pending to enable this fully.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some specific TCON chip has HW limitation to support PSRSU+DSC.
[how]
Force ffu mode when DSC enabled if we detect it is the specific
model from sink OUI DPCD. And disable ABM update for this case.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When DC driver send PSR exit dmub command to DMUB FW, it might not
wait until PSR exit. Then it may hit the following deadlock situation.
1. DC driver send HW LOCK command to DMUB FW due to frame update
2. DMUB FW Set the HW lock
3. DMUB execute PSR exit sequence and stuck at polling DPG Pending
register due to the HW Lock is set
4. DC driver ask DMUB FW to unlock HW lock, but DMUB FW is polling
DPG pending register
[how]
The reason why DC driver doesn't wait until PSR exit is because some of
the PSR state machine state is not update the dc driver. So when DC
driver read back the PSR state, it take the state for PSR inactive.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The current PSR SU programming margin is fixed base on FHD 60HZ
panel. If the resolution and refresh rate become higher, the time
of current margin might not cover the programming SU time.
[how]
Notice that the programming SU time is the same among different
panels.
Instead of fixing the margin with target line number, change the
margin unit to micro second which indicate the time needed for
programming SU. Then FW set the margin line number base on the
line time and margin time.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & how]
We only support line capture indication as 0 for PSRSU
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The Y-granularity panel parameter indicate the grid
pattern granularity in the Y direction for PSRSU.
[How]
Send the Y-granularity data by PSR_COPY_SETTINGS dmub command.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
set psr version as PSR-SU in kernel-FW interface function to ensure
the correct dmub command parameter is fed into FW.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix kernel-doc warnings for a comment that should not use
kernel-doc notation:
dmub_psr.c:235: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Set PSR power optimization flags.
dmub_psr.c:235: warning: missing initial short description on line:
* Set PSR power optimization flags.
Fixes: e5dfcd2727 ("drm/amd/display: dc_link_set_psr_allow_active refactoring")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Robin Chen <po-tchen@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSR Power on/off is done in PSR. Add a dc_debug option
and dmub setting to use PHY implementation of this instead.
[How]
Add a dc_debug option and dmub setting to use
PHY FSM Power up/down for PSR.
Co-authored-by: Shah Dharati <dharati.shah@amd.com>
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Shah Dharati <dharati.shah@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMCUB will hang if we send a PSR unsupported set version command.
This can occur if we fall-through into the default case in the switch
statement for PSR version.
[How]
Add an unsupported check after the switch statement.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
- Adding a DM interface to enable DSC over eDP on Linux
- DSC over eDP will allow to power savings by reducing
the bandwidth required to support panel's modes
- Apply link optimization algorithm to reduce link bandwidth
when DSC is enabled
[how]
- Read eDP panel's DSC capabilities
- Apply DSC policy on eDP panel based on its DSC capabilities
- Enable DSC encoder's on the pipe
- Enable DSC on panel's side by setting DSC_ENABLE DPCD register
- Adding link optimization algorithm to reduce link rate or lane
count based
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some panels require to use TPS3 pattern to wake up link in PSR mode.
[How]
To add TPS3 selection information in PSR settings command and pass to
DMUB FW.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Robin Chen <po-tchen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
PSR set power command wasn't setting panel instance
and command version which caused both streams
to overwrite the same PSR state.
[how]
Pass panel instance to the set power command function
and to DMUB and set command version enum
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To expose new power optimization flags to PSR interface. It allows the
PSR related power features can be enabled separately base on different
use scenarios.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Robin Chen <po-tchen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
PSR_STATE2b was introduced on DMCUB side, but not on the driver side,
which caused convert_psr_state helper function to return
PSR_STATE_INVALID. That caused visual lagging during state transition.
[how]
Add PSR_STATE2b to dc_psr_state and convert_psr_state
Reviewed-by: Wyatt Wood <Wyatt.Wood@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Building with W=1 complains about an empty 'else' statement, so use the
usual do-nothing-while-0 loop to quieten this warning.
../drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:113:53: warning: suggest braces around empty body in an 'else' statement [-Wempty-body]
113 | *state, retry_count);
Fixes: b30eda8d41 ("drm/amd/display: Add ETW log to dmub_psr_get_state")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Wyatt Wood <wyatt.wood@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
GPINT commands have the lowest priority in DMCUB, so it's possible
that the command isn't processed in time.
[How]
Add a log to help identify this case.
Reviewed-by: Koo Anthony <Anthony.Koo@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
For dual eDP when setting the new settings we need to set
command version to DMUB_CMD_PSR_CONTROL_VERSION_1, otherwise
DMUB will not read panel_inst parameter.
[how]
Instead of PSR_VERSION_1 pass DMUB_CMD_PSR_CONTROL_VERSION_1
Reviewed-by: Wood Wyatt <Wyatt.Wood@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Allow specifying which panel to take PSR Residency
measurements from.
[how]
Pass panel instance to DMUB through GPINT in the upper
8 bits of the parameter.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Updating PSR interfaces to allow PSR enablement
per eDP panel.
[how]
- Copying PSR command structures to DC
- Changing function interfaces to pass panel instance
- Communicating with DMUB per link instead of assuming
to use a single one
-Iterating through all PSR capable panels when enabling/disabling
all
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DSC is enabled before reset link and potentially cause DSC enable fail problem.
[How]
Enable DSC after link is reseted
Signed-off-by: Mike Hsieh <chun-wei.hsieh@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
GPINT command to get PSR state from FW times out.
[How]
Add retry to get valid PSR state.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable status is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
GPINT timeout is causing PSR_STATE_0 to be returned when it shouldn't.
We must guarantee that PSR is fully disabled before doing hw programming
on driver-side.
[How]
Return invalid state if GPINT command times out. Let existing retry
logic send the GPINT until successful.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Some existing DC interfaces are optimized to return a single eDP
link/stream. Refactored those DC interfaces to support multiple eDP.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warnings:
./drivers/gpu/drm/amd/display/dc/dce/dmub_psr.c:273:16-21: WARNING:
conversion to bool not needed here.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Since dmub_rb_cmds are not initialized to 0,
the header is filled with invalid data.
This is causing issues on the fw side.
[How]
Initialize dmub_rb_cmd unions to 0.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:38: warning: Function parameter or member 'raw_state' not described in 'convert_psr_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:81: warning: Function parameter or member 'dmub' not described in 'dmub_psr_get_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:81: warning: Function parameter or member 'state' not described in 'dmub_psr_get_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:97: warning: Function parameter or member 'dmub' not described in 'dmub_psr_set_version'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:97: warning: Function parameter or member 'stream' not described in 'dmub_psr_set_version'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:128: warning: Function parameter or member 'dmub' not described in 'dmub_psr_enable'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:128: warning: Function parameter or member 'enable' not described in 'dmub_psr_enable'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:128: warning: Function parameter or member 'wait' not described in 'dmub_psr_enable'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:177: warning: Function parameter or member 'dmub' not described in 'dmub_psr_set_level'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:177: warning: Function parameter or member 'psr_level' not described in 'dmub_psr_set_level'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:203: warning: Function parameter or member 'dmub' not described in 'dmub_psr_copy_settings'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:203: warning: Function parameter or member 'link' not described in 'dmub_psr_copy_settings'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:203: warning: Function parameter or member 'psr_context' not described in 'dmub_psr_copy_settings'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:284: warning: Function parameter or member 'dmub' not described in 'dmub_psr_force_static'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:301: warning: Function parameter or member 'dmub' not described in 'dmub_psr_get_residency'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:301: warning: Function parameter or member 'residency' not described in 'dmub_psr_get_residency'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:323: warning: Function parameter or member 'psr' not described in 'dmub_psr_construct'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:323: warning: Function parameter or member 'ctx' not described in 'dmub_psr_construct'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:332: warning: Function parameter or member 'ctx' not described in 'dmub_psr_create'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:349: warning: Function parameter or member 'dmub' not described in 'dmub_psr_destroy'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Wyatt Wood <wyatt.wood@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add a dual edp power optimization flag, so driver will
notify this flag to dmub FW to determine if apply the
power optimization.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Use GPINT command to get PSR residency from FW.
[How]
Hook up PSR residency command to DSAT.
Since PSR Count Request is deprecated, we will use this.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The intended use is to force PSR into active state and ignore all
events until explicit EXIT.
A new event force_static is added to power module. It is then sent
to FW.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some debug bits are not being copied from driver to fw.
[How]
Copy debug bits properly.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For DMUB implementation of PSR, the 'wait' parameter,
used to determine if driver should wait for PSR enable/disable,
is not implemented correctly.
[How]
Implement wait for PSR enable/disable.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Feature requires synchronization of dig, pipe, and cursor locking
between driver and fw.
[How]
Set flag to force psr to use hw lock mgr.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Debug flags are not set by default.
[How]
Set debug flags to 0
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The SDP deadline indicate the vertical time to send CRC
infopacket in PSR.
Signed-off-by: po-tchen <po-ting.chen@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Make a separation of what belongs in the differen dmub
headers
dmub_srv.h is for exposing dmub srv interface to rest of
driver.
other headers inside dmub/inc exposes cmds and definitions
that are owned by the firmware
[How]
keep firmware owned definitions in dmub/inc
move stuff that is purely driver interface headers to dmub/
since those are interface calls that are defined for rest of
driver to use
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For a type like PSR version, it makes sense for most of the code
to include a dc type, instead of having this a fw type define since
this is a capability and type exposed by dc.
Especially if it doesn't even need to communicate with the fw.
The code that is packing the firmware command message
should be the one who needs to translate the psr version
into a command that the firmware understands.
[How]
Add a dc_psr_version enum.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We read memory that we shouldn't be touching if the struct isn't
a full union dmub_rb_cmd.
[How]
Fix up all the callers and functions that take in the dmub_cmd_header
to use the dmub_rb_cmd instead.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some include paths don't need to have relative paths
And some types missing
[How]
make some changes to headers and modify include path
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
- Driver does not recognize new definitions of psr states.
- Internal tool is required for checking if psr is active.
[How]
- Parse psr state correctly so that driver will recognize psr state.
- Add visual confirmation that psr is active using existing mechanisms.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
As it stands, psr has feature flags in dm, stream, and link. Most are
not defined well enough, and different dm layers have different uses for
these same flags.
[How]
We define a new structure called psr_settings in dc_link that will hold
the following psr feature flags:
psr_feature_enable - psr is supported
psr_allow_active - psr is currently active
psr_version - internal psr version supported
psr_frame_capture_indication_req
psr_sdp_transmit_line_num_deadline
The last two flags were moved out of the power module
for the purposes of consolidating psr flags.
Their use is already well-defined.
Psr caps reported by sink will also be stored in dc_link,
in dpcd_caps.psr_caps.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can remove the NULL check for "res_ctx" and
"res_ctx->pipe_ctx[i].stream->link". Also it's nicer to align the
conditions using spaces so I re-indented a bit.
Longer explanation: The "res_ctx" pointer points to an address in the
middle of a struct so it can't be NULL. For
"res_ctx->pipe_ctx[i].stream->link" we know that it is equal to "link"
and "link" is non-NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:147:31: warning:
address of 'pipe_ctx->plane_res' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (!pipe_ctx || !&pipe_ctx->plane_res || !&pipe_ctx->stream_res)
~ ~~~~~~~~~~^~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:147:56: warning:
address of 'pipe_ctx->stream_res' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (!pipe_ctx || !&pipe_ctx->plane_res || !&pipe_ctx->stream_res)
~ ~~~~~~~~~~^~~~~~~~~~
2 warnings generated.
As long as pipe_ctx is not NULL, the address of members in this struct
cannot be NULL, which means these checks will always evaluate to false.
Fixes: 4c1a1335df ("drm/amd/display: Driverside changes to support PSR in DMCUB")
Link: https://github.com/ClangBuiltLinux/linux/issues/915
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is freeing the wrong variable so it will crash. It should be
freeing "*dmub" instead of "dmub".
Fixes: 4c1a1335df ("drm/amd/display: Driverside changes to support PSR in DMCUB")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
