[WHY?]
Max number of lines that can be used for prefetch due to type constraints is
63.75.
[HOW?]
Enforce maximum prefetch lines as 63.75.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
DCN32 uses fclk pstate watermarks for dummy pstate, and must always be
supported.
[HOW?]
Validation needs to be run with fclk pstate latency set
as the dummy pstate latency to get correct prefetch and bandwidth outputs.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Prefetch calculation loop was not exiting until utilizing all of vstartup if it
failed once. Locals need to be reset on each iteration of the loop.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- When transitioning a pipe in use (non-phantom) to become
a phantom pipe, we must fully disable the pipe first before
doing any phantom pipe programming
- Move phantom OTG enablement to after "regular" front-end
programming sequence (including wait for vupdate)
- If a pipe is being transitioned into a phantom pipe,
fully disable it first
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn314 uses optc2_configure_crc() that wraps
optc1_configure_crc() + set additional registers
not applicable to dcn314.
It's not critical but when used leads to warning like:
WARNING: drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c
Call Trace:
<TASK>
generic_reg_set_ex+0x6d/0xe0 [amdgpu]
optc2_configure_crc+0x60/0x80 [amdgpu]
dc_stream_configure_crc+0x129/0x150 [amdgpu]
amdgpu_dm_crtc_configure_crc_source+0x5d/0xe0 [amdgpu]
[How]
Use optc1_configure_crc() directly
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Firmware headers dictate that gpio_pin array only has a size of 8. The
count returned from vbios however is greater than 8.
Fix this by not using array indexing but incrementing the pointer since
gpio_pin definition in atomfirmware.h is hardcoded to size 8
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why and how:
causes unstable on certain surface format/mpo transitions
This reverts commit de020e5fa9
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- If we're enabling phantom pipe for a high
link rate display we could
fail DML on the phantom pipe since it's
set to virtual signal
- Therefore don't consider Output BPP for
phantom pipe
Reviewed-by: Dillon Varone <Dillon.Varone@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Unbounded requesting is getting configured for odm mode calculations which
is incorrect. This change checks whether mode requires odm ahead of time.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The cursor size (in memory) is currently incorrectly calculated,
resulting not enough CAB being allocated for static screen cursor
in MALL refresh. This results in cursor image corruption.
[How]
Use cursor pitch instead of cursor width when calculating cursor size.
Update num cache lines calculation to use the result of the cursor size
calculation instead of manually recalculating again.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Subvp src/dst stream rectangles are not being created with the same scaling
factors as the main stream.
[HOW?]
Make sure subvp stream src rectangle scales its height to have the same src/dst
ratio as the main stream.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
After applying pipesplit flags, DML can select a different configuration upon
revalidation, despite the desired one still being valid.
[HOW?]
Check the configuration is still has mode support, and apply it.
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
1. correct dram_channel_width (was hard coded to 4 for 32bit)
2. use dm's is_hvm_enable status flag for hostvm_en input for dml.
3. add a function to override to all dcn3.1x.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain high resolution displays exhibit DCC line corruption with SubVP
enabled. This is likely due to insufficient DCC meta data buffered
immediately after the mclk switch.
[How]
Add workaround to increase phantom pipe vactive height by
meta_row_height number of lines, thus increasing the amount of meta data
buffered immediately after mclk switch finishes.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HW recommend we enable this for better DF QoS for DCN 3.2.x
[how]
Add interfaces to hubbub to program register
Add initialization as part of init_hw
Add default settings for DCN 3.2.x
Add registry override for debug/tuning
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Jun Lei <jun.lei@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The workaround designed for some specific ASICs is wrongly applied
to SMU13 ASICs. That leads to some runpm hang.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
If we enable virtual display functionality on parts with
no display hardware we can end up trying to check for and
reserve the vbios FB area on devices where it doesn't exist.
Check if display hardware is actually present on the hardware
before trying to reserve the memory.
v2: move the check into common code
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is to resolve a regression, which fails to allocate
VRAM due to no free memory in application, the reason
is we add check of vram_pin_size for memory limit, and
application is pinning the memory for Peerdirect, KFD
should not count it in memory limit. So removing
vram_pin_size will resolve it.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise, some unexpected PCIE AER errors will be observed
in runtime suspend/resume cycle.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DM maps DRM CRTC degamma to DPP (pre-blending) degamma block, but DCE doesn't
support programmable degamma curve anywhere. Currently, a custom degamma is
accepted by DM but just ignored by DCE driver and degamma correction isn't
actually applied. There is no way to map custom degamma in DCE, therefore, DRM
CRTC degamma property shouldn't be enabled for DCE drivers.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[WHY?]
Max number of lines that can be used for prefetch due to type constraints is
63.75.
[HOW?]
Enforce maximum prefetch lines as 63.75.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
DCN32 uses fclk pstate watermarks for dummy pstate, and must always be
supported.
[HOW?]
Validation needs to be run with fclk pstate latency set
as the dummy pstate latency to get correct prefetch and bandwidth outputs.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Prefetch calculation loop was not exiting until utilizing all of vstartup if it
failed once. Locals need to be reset on each iteration of the loop.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
[Why]
dcn314 uses optc2_configure_crc() that wraps
optc1_configure_crc() + set additional registers
not applicable to dcn314.
It's not critical but when used leads to warning like:
WARNING: drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c
Call Trace:
<TASK>
generic_reg_set_ex+0x6d/0xe0 [amdgpu]
optc2_configure_crc+0x60/0x80 [amdgpu]
dc_stream_configure_crc+0x129/0x150 [amdgpu]
amdgpu_dm_crtc_configure_crc_source+0x5d/0xe0 [amdgpu]
[How]
Use optc1_configure_crc() directly
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
[Why]
The cursor size (in memory) is currently incorrectly calculated,
resulting not enough CAB being allocated for static screen cursor
in MALL refresh. This results in cursor image corruption.
[How]
Use cursor pitch instead of cursor width when calculating cursor size.
Update num cache lines calculation to use the result of the cursor size
calculation instead of manually recalculating again.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
[Why]
For DCN3.2 and DCN3.21, VBIOS has switch to using v3.0 of the VRAM
info struct. We should read and override the VRAM info in driver with
values provided by VBIOS to support memory downbin cases.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
[Why]
Some DPIA AUX replies have incorrect data length from original request.
This could lead to overwriting of destination buffer if reply length is
larger, which could cause invalid access to stack since many destination
buffers are declared as local variables.
[How]
Check for invalid length from DPIA AUX replies and trigger a retry if
reply length is not the same as original request. A DRM_WARN() dmesg log
is also produced.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
TA firmware loaded on psp v13_0_10, but it is missing in modinfo.
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On IGT, there is a test named amd_hotplug, and when the subtest basic is
executed on DCN31, we get the following error:
[drm] *ERROR* [CRTC:71:crtc-0] flip_done timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [CRTC:71:crtc-0] commit wait timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [CONNECTOR:88:DP-1] commit wait timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [PLANE:59:plane-3] commit wait timed out
After enable the page flip log with the below command:
echo -n 'format "[PFLIP]" +p' > /sys/kernel/debug/dynamic_debug/control
It is possible to see that the flip was submitted, but DC never replied
back, which generates time-out issues. This is an indication that the
HUBP surface flip is missing. This commit fixes this issue by adding
hubp1_set_flip_int to DCN31.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
Since introduction of patch "Query DPIA HPD status.", link detection at
boot could be accessing DPIA AUX, which will not succeed until
DMUB outbox messaging is enabled and results in below dmesg logs:
[ 160.840227] [drm:amdgpu_dm_process_dmub_aux_transfer_sync [amdgpu]] *ERROR* wait_for_completion_timeout timeout!
[How]
Enable DMUB outbox messaging before link detection at boot time.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
When p->gang_size equals 0, amdgpu_cs_pass1() will return directly
without freeing chunk_array, which will cause a memory leak issue,
this patch fixes it.
Fixes: 4624459c84 ("drm/amdgpu: add gang submit frontend v6")
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Dong Chenchen <dongchenchen2@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For DCN3.2 and DCN3.21, VBIOS has switch to using v3.0 of the VRAM
info struct. We should read and override the VRAM info in driver with
values provided by VBIOS to support memory downbin cases.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stream only configurations do not require DCFCLK, SOCCLK, DPPCLK
or FCLK. They also always allow pstate change.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Whenever disabling a phantom pipe, we must run through the
minimal transition sequence
- In the case where SetVisibility = false for the main pipe,
we also need to run through the min transtion when disabling
the phantom pipes
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Software state expects pipes to be configured for ODM, but due to the transition
occurring on a plane disable, the ODM enablement code is not run.
[HOW?]
Update ODM when removing a plane, and dynamic ODM is active. Also acquire pipe
lock when removing a plane.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why and how]
Clean up some irq service code for dcn201.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Liu Xi <xi.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The visual confirm bar is displayed on all displays, but is only
updated on a flip. If an update causes SubVP to be disabled on
all displays, but there are no updates on the other displays, it
will lead to stale information displayed on the non-active
displays. An example of this is playing a fullscreen video on a
rotated display.
[How]
Add a procedure to update visual confirm color for all pipes when
committing a plane.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
disable_vbios_mode_if_required() will set dpms_off to false
during boot when pixel clk dismatches with driver requires.
This will cause extra backlight on and off if OS call 2
times setmode.
[How]
Set dpms_off to true to keep power_off and
let OS control BL by display's powerState.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Zhongwei Zhang <Zhongwei.Zhang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some DPIA AUX replies have incorrect data length from original request.
This could lead to overwriting of destination buffer if reply length is
larger, which could cause invalid access to stack since many destination
buffers are declared as local variables.
[How]
Check for invalid length from DPIA AUX replies and trigger a retry if
reply length is not the same as original request. A DRM_WARN() dmesg log
is also produced.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
TA firmware loaded on psp v13_0_10, but it is missing in modinfo.
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On IGT, there is a test named amd_hotplug, and when the subtest basic is
executed on DCN31, we get the following error:
[drm] *ERROR* [CRTC:71:crtc-0] flip_done timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [CRTC:71:crtc-0] commit wait timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [CONNECTOR:88:DP-1] commit wait timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [PLANE:59:plane-3] commit wait timed out
After enable the page flip log with the below command:
echo -n 'format "[PFLIP]" +p' > /sys/kernel/debug/dynamic_debug/control
It is possible to see that the flip was submitted, but DC never replied
back, which generates time-out issues. This is an indication that the
HUBP surface flip is missing. This commit fixes this issue by adding
hubp1_set_flip_int to DCN31.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Since introduction of patch "Query DPIA HPD status.", link detection at
boot could be accessing DPIA AUX, which will not succeed until
DMUB outbox messaging is enabled and results in below dmesg logs:
[ 160.840227] [drm:amdgpu_dm_process_dmub_aux_transfer_sync [amdgpu]] *ERROR* wait_for_completion_timeout timeout!
[How]
Enable DMUB outbox messaging before link detection at boot time.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
There are several places where we don't want to check
if a particular asic could support DC, but rather, if
DC is enabled. Set a flag if DC is enabled and check
for that rather than if a device supports DC or not.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move it into the DCE code for each generation. This avoids
confusion with the different display paths.
v2: no need for a hotplug worker for vkms
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
virtual display is enabled unconditionally in SR-IOV, but
without specifying the virtual_display module, the number
of crtcs defaults to 0. Set a single display by default
for SR-IOV if the virtual_display parameter is not set.
Only enable virtual display by default on SR-IOV on asics
which actually have display hardware.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_device_asic_has_dc_support() just checks the asic itself.
amdgpu_device_has_dc_support() is a runtime check which not
only checks the asic, but also other things in the driver
like whether virtual display is enabled. We want the latter
here.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
GCMC_VM related registers should be programmed by PSP on host side.
L1 and RLCG will block these regisers on VF.
[How]
Remove programming GCMC_VM_FB_LOCATION_BASE/TOP on gfxhub_v3_0_3 under SRIOV VF.
Signed-off-by: Yifan Zha <Yifan.Zha@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Do not clear kiq position in RLC_CP_SCHEDULER so that CP could perform
IDLE-SAVE after VF fini. CPG also needs to be active in save command.
v2: drop unused variable (Alex)
Signed-off-by: YuBiao Wang <YuBiao.Wang@amd.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
