Instead of querying the CTL for the flush mask (for SSPP, LM or DSPP),
storing the mask in the mixer configuration and then pushing the mask to
the CTL, tell CTL to cache the flush in place.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/473159/
Link: https://lore.kernel.org/r/20220209172520.3719906-9-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
There is no need to use the struct msm_display_dsc_config wrapper inside
the dpu driver, use the struct drm_dsc_config directly to pass pps data.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/493340/
Link: https://lore.kernel.org/r/20220711100432.455268-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
dpu_encoder_helper_phys_cleanup() was not populating neither
wb or intf to the intf_cfg before calling the reset_intf_cfg().
This causes the reset of the active bits of wb/intf to be
skipped which is incorrect.
Fix this by populating the relevant wb or intf indices correctly.
Fixes: ae4d721ce1 ("drm/msm/dpu: add an API to reset the encoder related hw blocks")
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Tested-by: Jessica Zhang <quic_jesszhan@quicinc.com> # Trogdor (SC8170)
Patchwork: https://patchwork.freedesktop.org/patch/494298/
Link: https://lore.kernel.org/r/1657912468-17254-1-git-send-email-quic_abhinavk@quicinc.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Remove extra nestting level from the dpu_encoder_get_intf(), replacing it
with the explicit return in case the INTF_WB was passed to the function.
While we are at it, also change dpu_encoder_get_wb() to also use
explicit return rather than the goto.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/491189/
Link: https://lore.kernel.org/r/20220625003028.383259-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add support for writing CRC values for the interface block to
the debugfs by calling the necessary MISR setup/collect methods.
Changes since V1:
- Set values_cnt to only include phys with backing hw_intf
- Loop over all drm_encs connected to crtc
Changes since V2:
- Remove vblank.h inclusion
- Change `pos + i` to `pos + entries`
- Initialize values_cnt to 0 for encoder
- Change DPU_CRTC_CRC_SOURCE_INTF to DPU_CRTC_CRC_SOURCE_ENCODER (and
"intf" to "enc")
- Change dpu_encoder_get_num_phys to dpu_encoder_get_num_hw_intfs
- Add checks for setup_misr and collect_misr in
dpu_encoder_get_num_hw_intfs
Changes since V3:
- Remove extra whitespace
- Change "enc" to "encoder"
- Move crcs array to dpu_crtc_get_encoder_crc
- Rename dpu_encoder_get_num_hw_intfs to dpu_encoder_get_crc_values_cnt
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/490736/
Link: https://lore.kernel.org/r/20220622171835.7558-5-quic_jesszhan@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
intf and wb resources are not dependent on the rm global
state so need not be allocated during dpu_encoder_virt_atomic_mode_set().
Move the allocation of intf and wb resources to dpu_encoder_setup_display()
so that we can utilize the hw caps even during atomic_check() phase.
Since dpu_encoder_setup_display() already has protection against
setting invalid intf_idx and wb_idx, these checks can now
be dropped as well.
changes in v2:
- add phys->hw_intf and phys->hw_wb checks back
changes in v3:
- correct the Fixes tag
Fixes: e02a559a72 ("drm/msm/dpu: make changes to dpu_encoder to support virtual encoder")
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/489885/
Link: https://lore.kernel.org/r/1655406084-17407-1-git-send-email-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
After the commit c46f0d6903 ("drm/msm: remove unused hotplug and edid
macros from msm_drv.h") the msm_display_caps enum contains two bits
describing whether the encoder should work in video or command mode.
Drop the enum and replace capabilities field in struct msm_display_info
with boolean is_cmd_mode field.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/485454/
Link: https://lore.kernel.org/r/20220507115942.1705872-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The 'vsync_cnt' is used to count the number of frames for a crtc.
Unfortunately, we increment the count after waking up userspace via
dpu_crtc_vblank_callback() calling drm_crtc_handle_vblank().
drm_crtc_handle_vblank() wakes up userspace processes that have called
drm_wait_vblank_ioctl(), and if that ioctl is expecting the count to
increase it won't.
Increment the count before calling into the drm APIs so that we don't
have to worry about ordering the increment with anything else in drm.
This fixes a software video decode test that fails to see frame counts
increase on Trogdor boards.
Cc: Mark Yacoub <markyacoub@chromium.org>
Cc: Jessica Zhang <quic_jesszhan@quicinc.com>
Fixes: 885455d6bf ("drm/msm: Change dpu_crtc_get_vblank_counter to use vsync count.")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Jessica Zhang <quic_jesszhan@quicinc.com> # Trogdor (sc7180)
Patchwork: https://patchwork.freedesktop.org/patch/490531/
Link: https://lore.kernel.org/r/20220622023855.2970913-1-swboyd@chromium.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Commit 58dca98107 ("drm/msm/disp/dpu1: Add support for DSC in
encoder") added dsc_common_mode variable which was set to zero but then
again programmed, so drop the superfluous init.
Fixes: 58dca98107 ("drm/msm/disp/dpu1: Add support for DSC in encoder")
Reported-by: kernel test robot <yujie.liu@intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/487208/
Link: https://lore.kernel.org/r/20220525073912.2706505-1-vkoul@kernel.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Add wb_idx to existing DRM prints in dpu_encoder and also
print the intf_mode so that its clear that for any INTF_CMD/VID
there will be a valid intf_idx and any INTF_WB_* there will be a
valid wb_idx.
Update the debugfs to add the same information. Here is a sample
output with this change:
root:/sys/kernel/debug/dri/0/encoder31# cat status
intf:1 wb:-1 vsync: 31 underrun: 0 mode: INTF_MODE_VIDEO
root:/sys/kernel/debug/dri/0/encoder33# cat status
intf:-1 wb:2 vsync: 7 underrun: 0 mode: INTF_MODE_WB_LINE
Also remove DPU_DEBUG_PHYS macros as its unused because the
respective dpu_encoder_phys_* files have their own macros.
changes in v2:
- use switch case instead of if/else-if for get_intf_type
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/483530/
Link: https://lore.kernel.org/r/1650984096-9964-19-git-send-email-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
kms_writeback test cases also verify with a null fb for the
writeback connector job. In addition there are also other
commit paths which can result in kickoffs without a valid
framebuffer like while closing the fb which results in the
callback to drm_atomic_helper_dirtyfb() which internally
triggers a commit.
Add protection in the dpu driver to ensure that commits for
writeback encoders without a valid fb are gracefully skipped.
changes in v2:
- rename dpu_encoder_has_valid_fb to dpu_encoder_is_valid_for_commit
changes in v3:
- none
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/483522/
Link: https://lore.kernel.org/r/1650984096-9964-17-git-send-email-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Initialize dpu encoder and connector for writeback if the
target supports it in the catalog.
changes in v2:
- start initialing the encoder for writeback since we
have migrated to using drm_writeback_connector_init_with_encoder()
- instead of checking for WB_2 inside _dpu_kms_initialize_writeback
call it only when its WB_2
- rebase on tip of msm-next and remove usage of priv->encoders
changes in v3:
- none
changes in v4:
- fix copyright years order
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/483526/
Link: https://lore.kernel.org/r/1650984096-9964-16-git-send-email-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
add dpu encoder APIs to prepare and cleanup writeback job
for the writeback encoder. These shall be invoked from the
prepare_wb_job/cleanup_wb_job hooks of the drm_writeback
framework.
changes in v3:
- none
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/483516/
Link: https://lore.kernel.org/r/1650984096-9964-12-git-send-email-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add an API to reset the encoder related hw blocks to ensure
a proper teardown of the pipeline. At the moment this is being
used only for the writeback encoder but eventually we can start
using this for all interfaces.
changes in v4:
- none
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/483512/
Link: https://lore.kernel.org/r/1650984096-9964-10-git-send-email-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Remove additional indirection: specify IRQ callbacks and IRQ indices
directly rather than through the pointer in the irq structure. For each
IRQ we have a constant IRQ callback. This change simplifies code review
as the reader no longer needs to remember which function is called.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/474700/
Link: https://lore.kernel.org/r/20220217043148.480898-6-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
DPU interrupts code allows multiple callbacks per interrut. In reality
none of the interrupts is shared between blocks (and will probably never
be). Drop support for registering multiple callbacks per interrupt to
simplify interrupt handling code.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/474701/
Link: https://lore.kernel.org/r/20220217043148.480898-4-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
For DSC to work we typically need a 2,2,1 configuration. This should
suffice for resolutions up to 4k. For more resolutions like 8k this won't
work.
Also, it is better to use 2 LMs and DSC instances as half width results
in lesser power consumption as compared to single LM, DSC at full width.
The panel has been tested only with 2,2,1 configuration, so for
now we blindly create 2,2,1 topology when DSC is enabled
Co-developed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/480925/
Link: https://lore.kernel.org/r/20220406094031.1027376-11-vkoul@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
DPU supports different topologies for the case when multiple INTFs are
being driven by the single phys_enc. The driver defaults to using 3DMux
in such cases. Don't use it if DSC merge is used instead.
Suggested-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/480922/
Link: https://lore.kernel.org/r/20220406094031.1027376-9-vkoul@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
We need to configure the encoder for DSC configuration and calculate DSC
parameters for the given timing so this patch adds that support by
adding dpu_encoder_prep_dsc() which is invoked when DSC is enabled.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/480920/
Link: https://lore.kernel.org/r/20220406094031.1027376-8-vkoul@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Widebus feature will transmit two pixel data per pixel clock to interface.
This feature now is required to be enabled to easy migrant to higher
resolution applications in future. However since some legacy chipsets
does not support this feature, this feature is enabled by setting
wide_bus_en flag to true within msm_dp_desc struct.
changes in v2:
-- remove compression related code from timing
-- remove op_info from struct msm_drm_private
-- remove unnecessary wide_bus_en variables
-- pass wide_bus_en into timing configuration by struct msm_dp
Changes in v3:
-- split patch into 3 patches
-- enable widebus feature base on chip hardware revision
Changes in v5:
-- DP_INTF_CONFIG_DATABUS_WIDEN
Changes in v6:
-- static inline bool msm_dp_wide_bus_enable() in msm_drv.h
Changes in v7:
-- add Tested-by
Changes in v9:
-- add wide_bus_en to msm_dp_desc
Changes in v10:
-- add wide_bus_en boolean to dp_catalog struc to avoid passing it as parameter
Changes in v11:
-- add const to dp_catalog_hw_revision()
-- add const to msm_dp_wide_bus_available()
Changes in v12:
-- dp_catalog_hw_revision(const struct dp_catalog *dp_catalog)
-- msm_dp_wide_bus_available(const struct msm_dp *dp_display)
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/476283/
Link: https://lore.kernel.org/r/1645824192-29670-5-git-send-email-quic_khsieh@quicinc.com
[DB: fixed the compilation]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Widebus feature will transmit two pixel data per pixel clock to interface.
Timing engine provides driving force for this purpose. This patch base
on HPG (Hardware Programming Guide) to revise timing engine register
setting to accommodate both widebus and non widebus application. Also
horizontal width parameters need to be reduced by half since two pixel
data are clocked out per pixel clock when widebus feature enabled.
Widebus can be enabled individually at DP. However at DSI, widebus have
to be enabled along with DSC to achieve pixel clock rate be scaled down
with same ratio as compression ratio when 10 bits per source component.
Therefore this patch add no supports of DSI related widebus and compression.
Changes in v2:
-- remove compression related code from timing
-- remove op_info from struct msm_drm_private
-- remove unnecessary wide_bus_en variables
-- pass wide_bus_en into timing configuration by struct msm_dp
Changes in v3:
-- split patch into 3 patches
Changes in v4:
-- rework timing engine to not interfere with dsi/hdmi
-- cover both widebus and compression
Changes in v5:
-- remove supports of DSI widebus and compression
Changes in v7:
-- split this patch into 3 patches
-- add Tested-by
Changes in v8:
-- move new registers writes under DATA_HCTL_EN features check.
Changes in v10:
-- add const inside dpu_encoder_is_widebus_enabled()
-- drop useless parenthesis please
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/476281/
Link: https://lore.kernel.org/r/1645824192-29670-4-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
All physical encoders used by virtual encoder share the same connector,
so pull the connector field from dpu_encoder_phys into dpu_encoder_virt
structure. Otherwise code suggests that different phys_encs
can have different connectors.
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220217035358.465904-8-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Make dpu_encoder use atomic_mode_set to receive connector and CRTC
states as arguments rather than finding connector and CRTC by manually
looping through the respective lists.
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220217035358.465904-7-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Both cmd and vid backends provide useless mode_fixup() callback. Drop
it.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220217035358.465904-6-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
We do not use MSM bus client, so drop bus_scaling_client field from
dpu_encoder_virt.
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220217035358.465904-5-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
DP audio enablement code which is comparing intf_type,
DRM_MODE_ENCODER_TMDS (= 2) with DRM_MODE_CONNECTOR_DisplayPort (= 10).
Which would never succeed. Fix it to check for DRM_MODE_ENCODER_TMDS.
Fixes: d13e36d7d2 ("drm/msm/dp: add audio support for Display Port on MSM")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220217035358.465904-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
INTF blocks are not really handled by resource manager, they are
assigned at dpu_encoder_setup_display using dpu_encoder_get_intf().
Then this allocation is passed to RM and then returned to then
dpu_encoder.
So allocate them outside of RM and use them directly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20220121210618.3482550-4-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
We get warning:
In function ‘dpu_encoder_virt_enable’: drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:1145:33:
warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
1145 | struct msm_drm_private *priv;
In function ‘dpu_encoder_virt_disable’: drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:1182:33:
warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
1182 | struct msm_drm_private *priv;
Remove these unused but set variables
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20220210114106.290669-1-vkoul@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently the msm_dp_*** functions implement the same sequence which would
happen when drm_bridge is used. hence get rid of this intermediate layer
and align with the drm_bridge usage to avoid customized implementation.
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Changes in v2:
-- revise commit text
-- rename dp_bridge to msm_dp_bridge
-- delete empty functions
Changes in v3:
-- replace kzalloc() with devm_kzalloc()
-- replace __dp_display_enable() with dp_display_enable()
-- replace __dp_display_disable() with dp_display_disable()
Changes in v4:
-- msm_dp_bridge_init() called from msm_dp_modeset_init() same as dsi
Changes in v5:
-- delete attach, mode_fixup and pre_enable from dp_bridge_ops
Changes in v6:
-- rebase on msm-next-plus-fixes branch
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/1638918933-2544-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Based on the removal of the g_dp_display and the movement of the
priv->dp lookup into the DP code it's now possible to have multiple
DP instances.
In line with the other controllers in the MSM driver, introduce a
per-compatible list of base addresses which is used to resolve the
"instance id" for the given DP controller. This instance id is used as
index in the priv->dp[] array.
Then extend the initialization code to initialize struct drm_encoder for
each of the registered priv->dp[] and update the logic for associating
each struct msm_dp with the struct dpu_encoder_virt.
A new enum is introduced to document the connection between the
instances referenced in the dpu_intf_cfg array and the controllers in
the DP driver and sc7180 is updated.
Lastly, bump the number of struct msm_dp instances carries by priv->dp
to 3, the currently known maximum number of controllers found in a
Qualcomm SoC.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211016221843.2167329-6-bjorn.andersson@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Functions in the DisplayPort code that relates to individual instances
(encoders) are passed both the struct msm_dp and the struct drm_encoder.
But in a situation where multiple DP instances would exist this means
that the caller need to resolve which struct msm_dp relates to the
struct drm_encoder at hand.
Store a reference to the struct msm_dp associated with each
dpu_encoder_virt to allow the particular instance to be associate with
the encoder in the following patch.
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211016221843.2167329-3-bjorn.andersson@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
[why]
vsync_cnt atomic counter increments for every hw vsync. On the other
hand, frame count is a register that increments when the frame gets
actually pushed out. We cannnot read this register whenever the timing
engine is off, but vblank counter should still return a valid number.
This behavior also matches the downstream driver.
[How]
Read the encoder vsync count instead of the dpu_encoder_phys frame
count.
Suggested-by: Abhinav Kumar <abhinavk@codeaurora.org>
CC: Rob Clark <robdclark@chromium.org>
Signed-off-by: Mark Yacoub <markyacoub@chromium.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210830181359.124267-1-markyacoub@chromium.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add some missing newlines to the various DRM printks in this file.
Noticed while looking at logs. While we're here unbreak quoted
strings so grepping them is easier.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210708065619.999199-1-swboyd@chromium.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The result of container_of() operations is never NULL unless the embedded
element is the first element of the structure. This is not the case here.
The NULL checks on the result of container_of() are therefore unnecessary
and misleading. Remove them.
This change was made automatically with the following Coccinelle script.
@@
type t;
identifier v;
statement s;
@@
<+...
(
t v = container_of(...);
|
v = container_of(...);
)
...
when != v
- if (\( !v \| v == NULL \) ) s
...+>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210525112904.1747066-1-linux@roeck-us.net
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
[DB: fixed patch subject]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
These prints flood the logs with drm debugging set to enable kms and
driver logging (DRM_UT_KMS and DRM_UT_DRIVER). Let's move these prints
to the atomic bucket (DRM_UT_ATOMIC) as they're related to the atomic
paths.
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Cc: Kuogee Hsieh <khsieh@codeaurora.org>
Cc: aravindh@codeaurora.org
Cc: Sean Paul <sean@poorly.run>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210430193104.1770538-7-swboyd@chromium.org
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Merge dpu_core_irq_enable() into dpu_core_irq_register_callback() and
dpu_core_irq_disable() into dpu_core_irq_unregister_callback(), because
they are called in pairs. There is no need to have separate
enable/disable pair, we can enable hardware IRQ when first callback is
registered and when the last callback is unregistered.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210516202910.2141079-7-dmitry.baryshkov@linaro.org
[fixup tracepoint compile warns]
Signed-off-by: Rob Clark <robdclark@chromium.org>
The IRQ table in the dpu_hw_interrupts.h is big, ugly, and hard to
maintain. There are only few interrupts used from that table. Newer
generations use different IRQ locations. Move this data to hw catalog.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210516202910.2141079-5-dmitry.baryshkov@linaro.org
[fixup tracepoint compile warns/err]
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add snapshot points across dpu driver to trigger dumps when critical
errors are hit.
changes in v5:
- change the callers to use the snapshot function directly
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/1618606645-19695-8-git-send-email-abhinavk@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Set the flag vblank_disable_immediate = true to turn off vblank irqs
immediately as soon as drm_vblank_put is requested so that there are
no irqs triggered during idle state. This will reduce cpu wakeups
and help in power saving.
To enable vblank_disable_immediate flag the underlying KMS driver
needs to support high precision vblank timestamping and also a
reliable way of providing vblank counter which is incrementing
at the leading edge of vblank.
This patch also brings in changes to support vblank_disable_immediate
requirement in dpu driver.
Changes in v1:
- Specify reason to add vblank timestamp support. (Rob).
- Add changes to provide vblank counter from dpu driver.
Changes in v2:
- Fix warn stack reported by Rob Clark with v2 patch.
Changes in v3:
- Move back to HW frame counter (Rob).
Changes in v4:
- Frame count mismatch was causing a DRM WARN stack spew.
DPU HW will increment the frame count at the end of
the sync, where as vblank will be triggered at the
fetch_start counter which is calculated as v_total - vfp.
This is to start fetching early for panels with low
vbp w.r.t hw latency lines.
Add logic to detect the line count if it falls between
vactive and v_total then return incremented frame count value.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Link: https://lore.kernel.org/r/1613651746-12783-1-git-send-email-kalyan_t@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
