Parse the device properties and register the rotation and orientation
V4L2 controls using v4l2_ctrl_new_fwnode_properties().
Remove the open-coded parsing of the rotation property and assume the
DTS is correct is providing either <0> or <180> as possible rotations.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Implement the get_selection pad operation for the OV5640 sensor driver.
The supported targets report the sensor's native size, the active pixel
array size and the analog crop rectangle from which the image is
produced.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Implement the init_cfg pad operation to initialize the subdev state
format to the default one.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Now that the frame duration can be controlled by tuning the VBLANK
duration in CSI-2 mode, fix all modes definitions to comply with the
reported FPS.
All modes run at 30 FPS except for full-resolution mode 2592x1944
which runs at 15FPS.
Tested on a 2 data lanes setup in UYVY and RGB565 modes in CSI-2 mode.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The current implementation of ov5640_find_mode() fails if the
frame rate programmed with s_frame_interval doesn't match the
maximum frame rate for the current mode.
This causes issues when moving from one mode with higher FPS to another
one which only supports a lower FPS range with tools like media-ctl.
It also forces users that do not use s_frame_interval(), but rather
configure blankings explicitly, to adjust the programmed FPS range to
avoid failures.
For this reason, remove the FPS check from ov5640_find_mode() and only
perform it at s_frame_interval() time.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Adjust the vertical blanking when s_frame_interval is used.
s_frame_interval allows to set a fixed frame rate, which gets stored as
the sensor's current one. When a new mode is applied, the current frame
rate is reset to the mode's default one. In order to correctly report
the currently configured vertical blanking for s_frame_interval users,
verify that the desired frame rate has not been changed. If that's the
case, compute the correct blanking value and reflect it through the
corresponding v4l2 control.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the VBLANK control which allows to select the duration of the
frame vertical blankings and allows to control the framerate.
The VBLANK control also modifies the exposure time range, which cannot
exceed the maximum frame length.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the HBLANK control as read-only.
The hblank value is fixed in the mode definition and is updated
everytime a new format is applied.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ov5640_mode_init_data is a fictional sensor more which is used to
program the initial sensor settings.
It is only used to initialize the sensor and can be replaced
it with a throw-away mode which just wraps the register table.
Also rename the register table to drop the format from the name to make
it clear an actual sensor mode has to be applied after the initial
programming.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The register tables for all resolutions smaller than 720p are now
identical.
Remove the duplicated ones and create a single ov5640_setting_low_res[]
register table.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Provide a function to shortcut access to the correct timings definition
to avoid repeating the same pattern when accessing the sensor timings.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Separate the timings for the DVP mode from the timings for the CSI-2
mode in the ov5640 modes definition.
The CSI-2 timings will deviate from the DVP ones as the clock tree is
calculated differently.
In CSI-2 mode change the analog crop rectangles as the OV5640 pixel
array is composed as:
- vertically: 16 dummy columns, 2592 valid ones and 16 dummy columns for
a total of 2624 columns
- horizontally: 8 optical black lines, 6 dummy ones, 1944 valid and 6
dummies for a total of 1964 lines
Adjust the analog crop rectangle in CSI-2 mode to:
- Skip the first 16 dummy columns
- Skip the first 14 black/dummy lines
- Pass the whole valid pixel array size to the ISP for all modes except
1024x768, 720p and 1080p which are obtained by cropping the valid pixel
array.
Tested in RGB565, UYVY and RGB888 modes in CSI-2 mode.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Adjust the left crop of 720x480 to enable capture in RGB888 format,
which is otherwise broken.
The 56 pixels alignment has been copied from the 720x576 mode.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The current definition of a sensor mode defines timings as follows:
- hact, vact: Visible width and height
- htot, vtot: Total sizes including blankings
This makes difficult to clearly separate the visible sizes from the
blankings and to make the vertical blanking programmable.
Rework the sensor modes sizes definition to:
- Report the analog crop sizes
- Report the visible crop size
- Report the total pixels per line as HBLANK is fixed
- Report the VBLANK value to make it programmable
Also modify the ov5640_set_timings() function to program all the
windowing registers are remove them from the per-mode register-value
tables.
Do not change the timing values from the ones reported in the register
tables to maintain bisectability.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Re-work the ov5640_set_mipi_pclk() function to calculate the
PLL configuration using the pixel_rate and link_freq values set at
s_fmt time.
Rework the DVP clock mode settings to calculate the pixel clock
internally and remove the assumption on the 16bpp format.
Tested in MIPI CSI-2 mode with 1 and 2 data lanes with:
- all the sensor supported resolutions in UYVY, RGB565 and MJPEG formats.
- resolutions >= 1280x720 in RAW Bayer format.
- resolutions < 1280x720 in RGB888 format.
[Rework pclk_period and link_freq computation]
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
After having set a new format re-calculate the pixel_rate and link_freq
control values and update them when in MIPI mode.
Take into account the limitation of the link frequency having to be
strictly smaller than 1GHz when computing the desired link_freq, and
adjust the resulting pixel_rate acounting for the clock tree
configuration.
[Adjust link_freq calculation]
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the V4L2_CID_LINK_FREQ control to the ov5640 driver.
Make the control read-only for the moment.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Associate the bit depth to each format supported by the sensor.
The bpp will be used to calculate the line length.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Checking if the sensor is used in DVP or MIPI CSI-2 mode is a repeated
pattern which is about to be repeated more often.
Provide an inline function to shortcut that.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The array of supported modes is close to unreadable.
Re-arrange it giving it some room to breath.
Cosmetic change only.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add to each mode supported by the sensor the ideal pixel rate, as
defined by Table 2.1 in the chip manual.
The ideal pixel rate will be used to compute the MIPI CSI-2 clock tree.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon-kit
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Expose RGB & YUV 1X16 serial pixel format variants to comply
with CSI-2 camera sensor pixel formats.
Signed-off-by: Hugues Fruchet <hugues.fruchet@foss.st.com>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Those two formats were missing in the list of supported MBUS
formats.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The s_stream callback had several issues:
- If pm_runtime_get_sync() fails, the usage_count is not put.
- The sensor wasn't suspended if s_stream(subdev, 1) failed.
Fix this.
Fixes: ("media: i2c: Add pm_runtime support to ov7251")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fix build error when VIDEO_ISL7998X=y and V4L2_FWNODE=m
by selecting V4L2_FWNODE.
microblaze-linux-ld: drivers/media/i2c/isl7998x.o: in function `isl7998x_probe':
(.text+0x8f4): undefined reference to `v4l2_fwnode_endpoint_parse'
Cc: stable@vger.kernel.org # 5.18 and above
Fixes: 51ef2be546 ("media: i2c: isl7998x: Add driver for Intersil ISL7998x")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ASoC core has now been changed to default to the non-legacy DAI
naming, as such drivers using the new scheme no longer need to specify
the non_legacy_dai_naming flag.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623125250.2355471-36-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This bit is marked as reserved in the ADV Hardware Reference Manual.
Resetting this bit seems to cause increased video noise. Setting this
bit according to the Hardware Reference Manual reduces the video noise
immediately.
Signed-off-by: Benjamin Marty <info@benjaminmarty.ch>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When logging the infoframes the adv7604 driver stopped reading
infoframes at the first missing infoframe type. Instead it should
try all supported infoframe types.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver should disable the regulator when failing to probe.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported by smatch/sparse:
drivers/media/i2c/ov7251.c:1381 ov7251_s_stream() warn: inconsistent returns '&ov7251->lock'.
Locked on : 1381
Unlocked on: 1377
There's a lock unbalance at this routine, as it keeps the lock on
certain errors. Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a vblank control to the ov7251 driver.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a hblank control to the ov7251 driver. This necessitates setting
a default mode, for which I am simply picking the first available.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
V4L2 controls initialisation takes up a sizeable portion of the
driver's .probe() function. To keep things neat, move it to a
dedicated function.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Extend the .get_selection() callback to support other values for
sel->target, primarily to satisfy libcamera's requirements.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The .s_power() callback is deprecated, and now that we have pm_runtime
functionality in the driver there's no further use for it. Delete the
function.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add pm_runtime support to the ov7251 driver.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe() is quite busy for this driver; make it cleaner by moving the
chip verification to a dedicated function.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The OV7251 sensor is used as the IR camera sensor on the Microsoft
Surface line of tablets; this provides a 19.2MHz external clock, and
the Windows driver for this sensor configures a 319.2MHz link freq to
the CSI-2 receiver. Add the ability to support those rate to the
driver by defining a new set of PLL configs.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Rather than having the pll settings hidden inside mode blobs, define
them in structs and use a dedicated function to set them. This makes
it simpler to extend the driver to support other frequencies for both
the external clock and desired link frequency.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Each of the defined modes in the ov7251 driver uses the same link
frequency and pixel rate; just drop those members of the modes and
set the controls to read only during initialisation. Add a new
table defining the supported pixel rates to substitue for the values
hardcoded in the modes.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move the endpoint checking from .probe() to a dedicated function,
and additionally check that the firmware provided link frequencies
are a match for those supported by the driver. Store the index to the
matching link frequency so it can be easily identified later.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for enumeration through ACPI to the ov7251 driver
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
of_match_ptr isn't required as CONFIG_OF is already a dependency in Kconfig
Signed-off-by: Moses Christopher Bollavarapu <mosescb.dev@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
MWB gain register are used to set gain for each mwb channel mannually.
However, it will involve some artifacts if gain cannot be applied to
each channel synchronously. Enable global gain control to set digital
global gain instead of setting AWB gain separately to fix this issue.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
IS_ERR() and PTR_ERR() use wrong pointer, it should be
sensor->dovdd, fix it.
Fixes: e43ccb0a04 ("media: i2c: Add support for the OV5648 image sensor")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add V4L2_ASYNC as a dependency to match other drivers and prevent failures
when compile testing.
Fixes: ff3cc65cad ("media: v4l: async, fwnode: Improve module organisation")
Signed-off-by: Mike Pagano <mpagano@gentoo.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
