Recently we introduced a patch for fixing an MST issue, but it caused a
regression on Club 3D since we could not set a refresh rate higher than
60Hz. This commit fixes this issue by adding a proper check after
validating the stream.
Fixes: f04d275d94 ("drm/amd/display: add mst port output bw check")
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC debug option to configure dpia hpd processing delay is not required.
[How]
Remove dc debug option for dpia hpd delay and also added log for
querying dpia hpd state.
Reviewed-by: Mustapha Ghaddar <Mustapha.Ghaddar@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With ODM policy 2 to 1, there exists a new use case
scenario where stream content is unchanged, but ODM
may be used. When this happens, the stream needs
to be committed with a new pipe setting.
This did not happen due to stream change
detection logic not accounting for ODM.
[How]
Set ODM flag in stream and commit stream when change
in ODM has been detected due to policy change.
Reviewed-by: Samson Tam <Samson.Tam@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This w/a has a bad interaction with seamless boot toggling an
active stream. Most panels recover, however some fail leading
to display corruption.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unexpected change of aux hw mapping causes dmub soft hang when
initiate aux transation at wrong aux channel.
ddc_channel stands for hw dp aux index which is from vbios,
but link_index is pure software concept for link count depending on which link
is probed first. They are not interchangeable.
dmub aux transaction could pass if happens eDP link_index gets
the same value as vbios ddc_channel, e.g., ddc_channel = 1, link_index = 1
if they gets different, e.g., ddc_channel = 2, link_index = 0, overwrite
ddc_channel with link_index will have wrong ddc channel being used for aux
transaction in dmub PSR, cause aux transaction soft hang.
[How]
ddc_channel mapping to each link is determined by vbios and further
parsed in dc. Such info. should not be touched in any kind, otherwise
the mapping is screwed up leading to aux transaction timeout.
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Check lenc is not NULL since dynamic link encoder assignment could
end up assigning a NULL link encoder.
Reviewed-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It's possible that we don't have a link encoder assignment if the
context is NULL but we're calling dc_add_stream_to_ctx from DM directly.
Link encoder assignment will happen later after global validation
runs with fast_validate = false.
[How]
Remove the ASSERTION. We already guard against NULL link_enc.
Reviewed-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In the case where we don't support DMUB aux but we have DPIA links
in the configuration we might try to message AUX using the legacy
path - where DDC pin is NULL. This causes a NULL pointer dereference.
[How]
Guard against NULL DDC pin, return a failure for aux engine acquire.
Reviewed-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Setup the shift and mask of HDMI_ACP_SEND register
- Program the register in hdmi stream encoder
- Also update ACP register in azalia configuration
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alan Liu <HaoPing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
In general cases we want to keep the dram clock change requirement (we
prefer configs that support MCLK switch). Only override to false for
SubVP.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some parts are consuming dangerously close to maximum number of states
supported when updating the BB (i.e. 8).
[how]
Change maximum stages from 9 to 20.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jun Lei <jun.lei@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
While applying a state to hardware, there is a transition period where
the back-end is reset using the old state; then enabled using the new
state.
Generally, the link encoder configuration module queries
stream-to-encoder assignments in either the new or old state based on a
mode variable. During the transition there is a need to query both
states, however toggling this mode variable can lead to incorrect
programming of encoders.
[How]
- Add new function to explicity query stream-to-encoder assignment
in the current state rather than intermittently switch the mode
of operation of the link encoder assignment module.
- Add additional checks for encoder assignment defects.
- Explicitly reset the mode of operation if application of state
to hardware ends prematurely.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]:
On power down, virtual dal may try to delete link_encoders by
referencing uninitialized res_pool.
[How]:
Added guard against empty res_pool.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Martin Leung <martin.leung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix for a bug where we would try to timing sync 2 odm halves.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
When adding/removing a plane to some configurations, unsupported pipe
programming can occur when moving to a new plane. Such cases include pipe
split on multi-display, with MPO, and/or ODM.
[HOW?]
Add a safe transistion state that minimizes pipe usage before programming
new configuration. When adding a plane, the current state has the least
pipes required so it is applied without splitting. This must be applied
prior to updating the plane_state for seamless transition. When removing a
plane, the new state has the least pieps required so it is applied without
splitting.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Found when running igt@kms_atomic.
Userspace attempts to do a TEST_COMMIT when 0 streams which calls
dc_remove_stream_from_ctx. This in turn calls link_enc_unassign which
ends up modifying stream->link = NULL directly, causing the global
link_enc to be removed preventing further link activity and future link
validation from passing.
[How]
We take care of link_enc unassignment at the start of
link_enc_cfg_link_encs_assign so this call is no longer necessary.
Fixes global state from being modified while unlocked.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We want to enable Firmware Assisted Memory (FAMS) Switching, but first,
we need to add the required code infrastructure in DC before allowing it
in amdgpu_dm.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Newer DCN should use optc3
[How]
Declare optc3 vmin/vmax function in header.
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After some experimental tests, we noticed that we need to set
gpuvm_max_page_table_levels to '4' to meet the hardware requirements.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For Pixel Rate control, when on HDMI, HDMI DTO should be selected
instead of DP DTO.
[How]
Pass HDMI parameter for HDMI stream, and select correct DTO.
Signed-off-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For MPO we want to allocate less than maximum DET for MPO pipes because
we need enogh buffer to move DET back to other pipes when removing an
MPO plane. Also update regular DET allocation to use DET override (DCN32
has an internal policy which driver does not want to use)
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, we check if pixel_encoding is equal to
PIXEL_ENCODING_YCBCR422 to get the k1/k2 div parameters. This commit
changes this logic slightly by checking if two pixels per container are
used.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Most of the time, a single display uses the ODM combine. When using
multi-display, we use ODM combine only if it is necessary. These cases
are not flexible enough for us, and we can improve them to take
advantage of our hardware. We want to have more control over the ODM
policy.
[How]
This commit add a new debug flag named
enable_single_display_2to1_odm_policy to control the ODM policy and
another flag named enable_dp_dig_pixel_rate_div_policy to fine control
the ODM combine. This is possible by adding a new "pipe.dest" parameter
that can be set to ODM 2:1 combined if we use a single display. For
dynamic ODM combine, when using DP-DIG, DCN applies K2=2 settings for
ODM combine. Note that this feature affects the following registers:
- timing.pix_clk_100khz -> DP_VID_M, DP_VID_N
- requested_pix_clk_100hz -> DP_DTOn_PHASE
- OTGn_PIXEL_RATE_DIVK2
- DP_PIXEL_PER_CYCLE_PROCESSING_MODE
- DIG_FIFO_OUTPUT_PIXEL_MODE
- DP_VID_N_MUL
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add function to set pixels per cycle in DIG stream encoder
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]:
Lut pipeline will be hooked up differently in some asics
need to add new interfaces and missing registers.
[HOW]:
Add missing registers and hook up programming from DPP for pre-blend
lut.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit enables the SubVP feature. To achieve that, we need to:
- Don't force p-state disallow on SubVP (can't block dummy p-state)
- Send calculated watermark to DMCUB for SubVP
- Adjust CAB mode message to PMFW
- Add a proper locking sequence for SubVP
- Various fixes to SubVP static analysis and determining SubVP config
- Currently SubVP not supported with pipe split so merge all pipes
before setting up SubVp
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are missing some ACP registers/mask value for some specific ASICs.
This commit includes it to those ASICs that support it.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It should not init whole ras bad page framework on sriov guest side
due to it is handled on host side.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFX is the only IP block that RAS TA needs to program
the hardware when receiving enable_feature command.
Changed from V1:
remove amdgpu_ras_need_send_ras_feature inline function,
use GFX RAS block check directly.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
And bump the version to 0x2A.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We don't need to validate and map root PD specially here,
it would be validated and mapped by amdgpu_vm_validate_pt_bos
if it is evicted.
The special case is when turning a GFX VM to a compute VM,
if vm_update_mode changed, we should make sure root PD gets
mapped. So just map root PD after updating vm->update_funcs
in amdgpu_vm_make_compute whether the vm_update_mode changed
or not.
v3:
- Add some comments suggested by Christian.
v2:
- Don't rename vm_validate_pt_pd_bos and make it public.
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Expose a new dc debug mask enum to force a subviewport memory clock switch
to facilitate easy testing.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When we tried to compile DCN32/321 for 32-bit architecture, we got this
error message:
ERROR: modpost: "__nedf2" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
This commit fixes this issue by rewriting a small part of the
dcn32_build_wm_range_table.
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Fixes: 265280b998 ("drm/amd/display: add CLKMGR changes for DCN32/321")
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Sometimes when trying to enable some feature, we have to define some
values with educated guesses, but we mark those values as TBD, which
means "To Be Determined". However, the correct way to approach it is by
loading that information from the firmware. Anyway, some of the values
that we were experimenting with caused this issue:
ERROR: modpost: "__muldf3" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
This commit fixes this issue by removing the division by two since it is
harmless in this case.
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Fixes: 265280b998 ("drm/amd/display: add CLKMGR changes for DCN32/321")
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When we tried to compile DCN32/321 for 32-bit architecture, we got this
error message:
ERROR: modpost: "__floatunsidf" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
This was caused because we were trying to assign an unsigned int to a
double value which causes issues for 32-bit architecture. This issue can
be fixed by changing the value type.
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Fixes: 265280b998 ("drm/amd/display: add CLKMGR changes for DCN32/321")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
While we tried to build amdgpu on i386, we got this error:
ERROR: modpost: "__umoddi3" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
This commit fixes this issue by replacing the standard module operator
with div_u64_rem.
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Fixes: d3dfceb58d ("drm/amd/display: Add dependant changes for DCN32/321")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The synchronize_rcu may take several ms, which noticeably slows down
applications close SMI event handle. Use call_rcu to free client->fifo
and client asynchronously and eliminate the synchronize_rcu call in the
user thread.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SVM range unmapped from GPUs when range is unmapped from CPU, or with
xnack on from MMU notifier when range is evicted or migrated.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Output user queue eviction and restore event. User queue eviction may be
triggered by svm or userptr MMU notifier, TTM eviction, device suspend
and CRIU checkpoint and restore.
User queue restore may be rescheduled if eviction happens again while
restore.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For migration start and end event, output timestamp when migration
starts, ends, svm range address and size, GPU id of migration source and
destination and svm range attributes,
Migration trigger could be prefetch, CPU or GPU page fault and TTM
eviction.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use ktime_get_boottime_ns() as timestamp to correlate with other
APIs. Output timestamp when GPU recoverable fault starts and ends to
recover the fault, if migration happened or only GPU page table is
updated to recover, fault address, if read or write fault.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Process receive event from same process by default. Add a flag to be
able to receive event from all processes, this requires super user
permission.
Event using pid 0 to send the event to all processes, to keep the
default behavior of existing SMI events.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 8748de873f
since drv enabled mes to access registers.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable mes to access registers.
v2: squash mes sched ring enablement flag
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add misc op commands in mes11.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFX10 and up have work group processors (WGP) and WGP mode is the native
compile mode.
KFD and ROCr have no visibility into whether a dispatch is operating
in CU or WGP mode.
Enforce CU masking to be pairwise continguous in enablement and
round robin distribute CUs across the SEs in a pairwise manner to
assume WGP mode at all times.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
