During devlink reload it is needed to remove debugfs entries
correlated with only one PF. ice_debugfs_exit() removes all
entries created by ice driver so we can't use it.
Introduce ice_debugfs_pf_deinit() in order to release PF's
debugfs entries. Move ice_debugfs_exit() call to ice_module_exit(),
it makes more sense since ice_debugfs_init() is called in
ice_module_init() and not in ice_probe().
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Recent changes to the devlink reload (commit 9b2348e2d6
("devlink: warn about existing entities during reload-reinit"))
force the drivers to destroy devlink ports during reinit.
Adjust ice driver to this requirement, unregister netdvice, destroy
devlink port. ice_init_eth() was removed and all the common code
between probe and reload was moved to ice_load().
During devlink reload we can't take devl_lock (it's already taken)
and in ice_probe() we have to lock it. Use devl_* variant of the API
which does not acquire and release devl_lock. Guard ice_load()
with devl_lock only in case of probe.
Suggested-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
HW incorrectly reports EIPE errors on encapsulated packets
with L2 padding inside inner packet. HW shows outer UDP/IPV4
packet checksum errors as part of the EIPE flags of the
Rx descriptor. These are reported only if checksum offload
is enabled and L3/L4 parsed flag is valid in Rx descriptor.
When that error is reported by HW, we don't act on it
instead of incrementing main Rx errors statistic as it
would normally happen.
Add a new statistic to count these errors since we still want
to print them.
Signed-off-by: Aniruddha Paul <aniruddha.paul@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jan Glaza <jan.glaza@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add PTP state machine so that the driver can correctly identify PTP
state around resets.
When the driver got information about ungraceful reset, PTP was not
prepared for reset and it returned error. When this situation occurs,
prepare PTP before rebuilding its structures.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce new capability - Low Latency Timestamping with Interrupt.
On supported devices, driver can request a single timestamp from FW
without polling the register afterwards. Instead, FW can issue
a dedicated interrupt when the timestamp was read from the PHY register
and its value is available to read from the register.
This eliminates the need of bottom half scheduling, which results in
minimal delay for timestamping.
For this mode, allocate TS indices sequentially, so that timestamps are
always completed in FIFO manner.
Co-developed-by: Yochai Hagvi <yochai.hagvi@intel.com>
Signed-off-by: Yochai Hagvi <yochai.hagvi@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Schedule service task and EXTTS in the top half to avoid bottom half
scheduling if possible, which significantly reduces timestamping delay.
Co-developed-by: Michal Michalik <michal.michalik@intel.com>
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-----BEGIN PGP SIGNATURE-----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=stU2
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Alexei Starovoitov says:
====================
pull-request: bpf-next 2023-12-18
This PR is larger than usual and contains changes in various parts
of the kernel.
The main changes are:
1) Fix kCFI bugs in BPF, from Peter Zijlstra.
End result: all forms of indirect calls from BPF into kernel
and from kernel into BPF work with CFI enabled. This allows BPF
to work with CONFIG_FINEIBT=y.
2) Introduce BPF token object, from Andrii Nakryiko.
It adds an ability to delegate a subset of BPF features from privileged
daemon (e.g., systemd) through special mount options for userns-bound
BPF FS to a trusted unprivileged application. The design accommodates
suggestions from Christian Brauner and Paul Moore.
Example:
$ sudo mkdir -p /sys/fs/bpf/token
$ sudo mount -t bpf bpffs /sys/fs/bpf/token \
-o delegate_cmds=prog_load:MAP_CREATE \
-o delegate_progs=kprobe \
-o delegate_attachs=xdp
3) Various verifier improvements and fixes, from Andrii Nakryiko, Andrei Matei.
- Complete precision tracking support for register spills
- Fix verification of possibly-zero-sized stack accesses
- Fix access to uninit stack slots
- Track aligned STACK_ZERO cases as imprecise spilled registers.
It improves the verifier "instructions processed" metric from single
digit to 50-60% for some programs.
- Fix verifier retval logic
4) Support for VLAN tag in XDP hints, from Larysa Zaremba.
5) Allocate BPF trampoline via bpf_prog_pack mechanism, from Song Liu.
End result: better memory utilization and lower I$ miss for calls to BPF
via BPF trampoline.
6) Fix race between BPF prog accessing inner map and parallel delete,
from Hou Tao.
7) Add bpf_xdp_get_xfrm_state() kfunc, from Daniel Xu.
It allows BPF interact with IPSEC infra. The intent is to support
software RSS (via XDP) for the upcoming ipsec pcpu work.
Experiments on AWS demonstrate single tunnel pcpu ipsec reaching
line rate on 100G ENA nics.
8) Expand bpf_cgrp_storage to support cgroup1 non-attach, from Yafang Shao.
9) BPF file verification via fsverity, from Song Liu.
It allows BPF progs get fsverity digest.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (164 commits)
bpf: Ensure precise is reset to false in __mark_reg_const_zero()
selftests/bpf: Add more uprobe multi fail tests
bpf: Fail uprobe multi link with negative offset
selftests/bpf: Test the release of map btf
s390/bpf: Fix indirect trampoline generation
selftests/bpf: Temporarily disable dummy_struct_ops test on s390
x86/cfi,bpf: Fix bpf_exception_cb() signature
bpf: Fix dtor CFI
cfi: Add CFI_NOSEAL()
x86/cfi,bpf: Fix bpf_struct_ops CFI
x86/cfi,bpf: Fix bpf_callback_t CFI
x86/cfi,bpf: Fix BPF JIT call
cfi: Flip headers
selftests/bpf: Add test for abnormal cnt during multi-kprobe attachment
selftests/bpf: Don't use libbpf_get_error() in kprobe_multi_test
selftests/bpf: Add test for abnormal cnt during multi-uprobe attachment
bpf: Limit the number of kprobes when attaching program to multiple kprobes
bpf: Limit the number of uprobes when attaching program to multiple uprobes
bpf: xdp: Register generic_kfunc_set with XDP programs
selftests/bpf: utilize string values for delegate_xxx mount options
...
====================
Link: https://lore.kernel.org/r/20231219000520.34178-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Users want the ability to debug FW issues by retrieving the
FW logs from the E8xx devices. Use debugfs to allow the user to
configure the log level and number of messages for FW logging.
If FW logging is supported on the E8xx then the file 'fwlog' will be
created under the PCI device ID for the ice driver. If the file does not
exist then either the E8xx doesn't support FW logging or debugfs is not
enabled on the system.
One thing users want to do is control which events are reported. The
user can read and write the 'fwlog/modules/<module name>' to get/set
the log levels. Each module in the FW that supports logging ht as a file
under 'fwlog/modules' that supports reading (to see what the current log
level is) and writing (to change the log level).
The format to set the log levels for a module are:
# echo <log level> > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/<module>
The supported log levels are:
* none
* error
* warning
* normal
* verbose
Each level includes the messages from the previous/lower level
The modules that are supported are:
* general
* ctrl
* link
* link_topo
* dnl
* i2c
* sdp
* mdio
* adminq
* hdma
* lldp
* dcbx
* dcb
* xlr
* nvm
* auth
* vpd
* iosf
* parser
* sw
* scheduler
* txq
* rsvd
* post
* watchdog
* task_dispatch
* mng
* synce
* health
* tsdrv
* pfreg
* mdlver
* all
The module 'all' is a special module which allows the user to read or
write to all of the modules.
The following example command would set the DCB module to the 'normal'
log level:
# echo normal > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/dcb
If the user wants to set the DCB, Link, and the AdminQ modules to
'verbose' then the commands are:
# echo verbose > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/dcb
# echo verbose > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/link
# echo verbose > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/adminq
If the user wants to set all modules to the 'warning' level then the
command is:
# echo warning > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/all
If the user wants to disable logging for a module then they can set the
level to 'none'. An example setting the 'watchdog' module is:
# echo none > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/watchdog
If the user wants to see what the log level is for a specific module
then the command is:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/dcb
This will return the log level for the DCB module. If the user wants to
see the log level for all the modules then the command is:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/all
Writing to the module file will update the configuration, but NOT enable the
configuration (that is a separate command).
In addition to configuring the modules, the user can also configure the
number of log messages (nr_messages) to include in a single Admin Receive
Queue (ARQ) event.The range is 1-128 (1 means push every log message, 128
means push only when the max AQ command buffer is full). The suggested
value is 10.
To see/change the resolution the user can read/write the
'fwlog/nr_messages' file. An example changing the value to 50 is
# echo 50 > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/nr_messages
To see the current value of 'nr_messages' then the command is:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/nr_messages
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Allow the user to set the symmetric Toeplitz hash function via:
# ethtool -X eth0 hfunc toeplitz symmetric-xor
All existing RSS configurations will be converted to symmetric unless they
have a non-symmetric field (other than IP src/dst and L4 src/dst ports)
used for hashing. The driver will reject a new RSS configuration if such
a field is requested.
The hash function in the E800 NICs is set per-VSI and a specific AQ
command is needed to modify the hash function. Use the AQ command to
enable setting the symmetric Toeplitz RSS hash function for any VSI
in the new ice_set_rss_hfunc().
When the Symmetric Toeplitz hash function is used, the hardware sets the
input set of the RSS (Toeplitz) algorithm to be the XOR of the fields
index by HSYMM and the fields index by the INSET registers. We use this
to create a symmetric hash by setting the HSYMM registers to point to
their counterparts in the INSET registers:
HSYMM [src_fv] = dst_fv;
HSYMM [dst_fv] = src_fv;
where src_fv and dst_fv are the indexes of the protocol's src and dst
fields.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Jeff Guo <jia.guo@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-8-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use previously refactored code and create a function
that allows XDP code to read HW timestamp.
Also, introduce packet context, where hints-related data will be stored.
ice_xdp_buff contains only a pointer to this structure, to avoid copying it
in ZC mode later in the series.
HW timestamp is the first supported hint in the driver,
so also add xdp_metadata_ops.
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-6-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Rebuilding CP VSI each time the PR is created drastically increase the
time of maximum VFs creation. Add function to reserve number of CP
queues to deal with this problem.
Use the same function to decrease number of queues in case of removing
VFs. Assume that caller of ice_eswitch_reserve_cp_queues() will also
call ice_eswitch_attach/detach() correct number of times.
Still one by one PR adding is handy for VF resetting routine.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Instead of assuming that each VF has pointer to port representor save it
in xarray. It will allow adding port representor for other device types.
Drop reference to VF where it is use only to get port representor. Get
it from xarray instead.
The functions will no longer by specific for VF, rename them.
Track id assigned by xarray in port representor structure. The id can't
be used as ::q_id, because it is fixed during port representor lifetime.
::q_id can change after adding / removing other port representors.
Side effect of removing VF pointer is that we are losing VF MAC
information used in unrolling. Store it in port representor as parent
MAC.
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Eswitch is used as a prefix for related functions. Main structure
storing all data related to eswitch should also be named as eswitch
instead of ice_switchdev_info. Rename it.
Also rename switchdev to eswitch where the context is not about eswitch
mode.
::uplink_netdev was changed to netdev for simplicity. There is no other
netdev in function scope so it is obvious.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Create a bitamp to track MSI-X usage for VFs. The bitmap has the size of
total MSI-X amount on device, because at init time the amount of MSI-X
used by VFs isn't known.
The bitmap is used in follow up patchset to provide a block of
continuous block of MSI-X indexes for each created VF.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor ice_get_link_ksettings to using forced speed to link modes
mapping.
Suggested-by : Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a problem in HW in E822-based devices leading to race
condition.
It might happen that, in order:
- PF0 (which owns the PHC) requests few timestamps,
- PF1 requests a timestamp,
- interrupt is being triggered and both PF0 and PF1 threads are woken
up,
- PF0 got one timestamp, still waiting for others so not going to sleep,
- PF1 gets it's timestamp, process it and go to sleep,
- PF1 requests a timestamp again,
- just before PF0 goes to sleep timestamp of PF1 appear,
- PF0 finishes all it's timestamps and go to sleep (PF1 also sleeping).
That leaves PF1 timestamp memory not read, which lead to blocking the
next interrupt from arriving.
Fix it by adding auxiliary devices and only one driver to handle all the
timestamps for all PF's by PHC owner. In the past each PF requested it's
own timestamps and process it from the start till the end which causes
problem described above. Currently each PF requests the timestamps as
before, but the actual reading of the completed timestamps is being done
by the PTP auxiliary driver, which is registered by the PF which owns PHC.
Additionally, the newly introduced auxiliary driver/devices for PTP clock
owner will be used for other features in all products (including E810).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add ice_pf_src_tmr_owned() macro to check the function capability bit
indicating if the current function owns the PTP hardware clock. This is
slightly shorter than the more verbose access via
hw.func_caps.ts_func_info.src_tmr_owned. Use this where possible rather
than open coding its equivalent.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ICE_F_PTP_EXTTS feature flag is ostensibly intended to support checking
whether the device supports external timestamp pins. It is only checked in
E810-specific code flows, and is enabled for all E810-based devices. E822
and E823 flows unconditionally enable external timestamp support.
This makes the feature flag meaningless, as it is always enabled. Just
unconditionally enable support for external timestamp pins and remove this
unnecessary flag.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Control over clock generation unit is required for further development
of Synchronous Ethernet feature. Interface provides ability to obtain
current state of a dpll, its sources and outputs which are pins, and
allows their configuration.
Co-developed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Milena Olech <milena.olech@intel.com>
Co-developed-by: Michal Michalik <michal.michalik@intel.com>
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add firmware admin command to access clock generation unit
configuration, it is required to enable Extended PTP and SyncE features
in the driver.
Add definitions of possible hardware variations of input and output pins
related to clock generation unit and functions to access the data.
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mitigate race between registering on wait list and receiving
AQ Response from FW.
ice_aq_prep_for_event() should be called before sending AQ command,
ice_aq_wait_for_event() should be called after sending AQ command,
to wait for AQ Response.
Please note, that this was found by reading the code,
an actual race has not yet materialized.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Expose struct ice_aq_task to callers,
what takes burden of memory ownership out from AQ-wait family of functions,
and reduces need for heap-based allocations.
Embed struct ice_rq_event_info event into struct ice_aq_task
(instead of it being a ptr) to remove some more code from the callers.
Subsequent commit will improve more based on this one.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the defines, fields, and detection code for FW support of LAG for
SRIOV. Also exposes some previously static functions to allow access
in the lag code.
Clean up code that is unused or not needed for LAG support. Also add
an ordered workqueue for processing LAG events.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Port VLAN in this case means push and pop VLAN action on specific vid.
There are a few limitation in hardware:
- push and pop can't be used separately
- if port VLAN is used there can't be any trunk VLANs, because pop
action is done on all traffic received by VSI in port VLAN mode
- port VLAN mode on uplink port isn't supported
Reflect these limitations in code using dev_info to inform the user
about unsupported configuration.
In bridge mode there is a need to configure port vlan without resetting
VFs. To do that implement ice_port_vlan_on/off() functions. They are
only configuring correct vlan_ops to allow setting port vlan.
We also need to clear port vlan without resetting the VF which is not
supported right now. Change it by implementing clear_port_vlan ops.
As previous VLAN configuration isn't always the same, store current
config while creating port vlan and restore it in clear function.
Configuration steps:
- configure switchdev with bridge
- #bridge vlan add dev eth0 vid 120 pvid untagged
- #bridge vlan add dev eth1 vid 120 pvid untagged
- ping from VF0 to VF1
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
With this patch, ice driver is able to track if the port
representors or uplink port were added to the linux bridge in
switchdev mode. Listen for NETDEV_CHANGEUPPER events in order to
detect this. ice_esw_br data structure reflects the linux bridge
and stores all the ports of the bridge (ice_esw_br_port) in
xarray, it's created when the first port is added to the bridge and
freed once the last port is removed. Note that only one bridge is
supported per eswitch.
Bridge port (ice_esw_br_port) can be either a VF port representor
port or uplink port (ice_esw_br_port_type). In both cases bridge port
holds a reference to the VSI, VF's VSI in case of the PR and uplink
VSI in case of the uplink. VSI's index is used as an index to the
xarray in which ports are stored.
Add a check which prevents configuring switchdev mode if uplink is
already added to any bridge. This is needed because we need to listen
for NETDEV_CHANGEUPPER events to record if the uplink was added to
the bridge. Netdevice notifier is registered after eswitch mode
is changed to switchdev.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_ptp_extts_work() and ice_ptp_periodic_work() functions are both
scheduled on the same kthread worker, pf.ptp.kworker. The
ice_ptp_periodic_work() function sends to the firmware to interact with the
PHY, and must block to wait for responses.
This can cause delay in responding to the PFINT_OICR_TSYN_EVNT interrupt
cause, ultimately resulting in disruption to processing an input signal of
the frequency is high enough. In our testing, even 100 Hz signals get
disrupted.
Fix this by instead processing the signal inside the miscellaneous
interrupt thread prior to handling Tx timestamps.
Use atomic bits in a new pf->misc_thread bitmap in order to safely
communicate which tasks require processing within the
ice_misc_intr_thread_fn(). This ensures the communication of desired tasks
from the ice_misc_intr() are correctly processed without racing even in the
event that the interrupt triggers again before the thread function exits.
Fixes: 172db5f91d ("ice: add support for auxiliary input/output pins")
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There was a change previously to stop SR-IOV and LAG from existing on the
same interface. This was to prevent the violation of LACP (Link
Aggregation Control Protocol). The method to achieve this was to add a
no-op Rx handler onto the netdev when SR-IOV VFs were present, thus
blocking bonding, bridging, etc from claiming the interface by adding
its own Rx handler. Also, when an interface was added into a aggregate,
then the SR-IOV capability was set to false.
There are some users that have in house solutions using both SR-IOV and
bridging/bonding that this method interferes with (e.g. creating duplicate
VFs on the bonded interfaces and failing between them when the interface
fails over).
It makes more sense to provide the most functionality
possible, the restriction on co-existence of these features will be
removed. No additional functionality is currently being provided beyond
what existed before the co-existence restriction was put into place. It is
up to the end user to not implement a solution that would interfere with
existing network protocols.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor ice_phy_type_to_ethtool to use phy_type_[low|high]_lkup table to
map PHY type to AQ link speed and ethtool link mode. This removes
complexity and simplifies future changes.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently driver can only allocate interrupt vectors during init phase by
calling pci_alloc_irq_vectors. Change that and make use of new
pci_msix_alloc_irq_at/pci_msix_free_irq API and enable to allocate and free
more interrupts after MSIX has been enabled. Since not all platforms
supports dynamic allocation, check it with pci_msix_can_alloc_dyn.
Extend the tracker to keep track how many interrupts are allocated
initially so when all such vectors are already used, additional interrupts
are automatically allocated dynamically. Remember each interrupt allocation
method to then free appropriately. Since some features may require
interrupts allocated dynamically add appropriate VSI flag and take it into
account when allocating new interrupt.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace custom interrupt tracker with generic xarray data structure.
Remove all code responsible for searching for a new entry with xa_alloc,
which always tries to allocate at the lowes possible index. As a result
driver is always using a contiguous region of the MSIX vector table.
New tracker keeps ice_irq_entry entries in xarray as opaque for the rest
of the driver hiding the entry details from the caller.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently interrupt allocations, depending on a feature are distributed
in batches. Also, after allocation there is a series of operations that
distributes per irq settings through that batch of interrupts.
Although driver does not yet support dynamic interrupt allocation, keep
allocated interrupts in a pool and add allocation abstraction logic to
make code more flexible. Keep per interrupt information in the
ice_q_vector structure, which yields ice_vsi::base_vector redundant.
Also, as a result there are a few functions that can be removed.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Keep interrupt handling code in a dedicated file. This helps keep driver
structured better and prepares for more functionality added to this file.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
RDMA is not supported in ice on a PF that has been added to a bonded
interface. To enforce this, when an interface enters a bond, we unplug
the auxiliary device that supports RDMA functionality. This unplug
currently happens in the context of handling the netdev bonding event.
This event is sent to the ice driver under RTNL context. This is causing
a deadlock where the RDMA driver is waiting for the RTNL lock to complete
the removal.
Defer the unplugging/re-plugging of the auxiliary device to the service
task so that it is not performed under the RTNL lock context.
Cc: stable@vger.kernel.org # 6.1.x
Reported-by: Jaroslav Pulchart <jaroslav.pulchart@gooddata.com>
Link: https://lore.kernel.org/netdev/CAK8fFZ6A_Gphw_3-QMGKEFQk=sfCw1Qmq0TVZK3rtAi7vb621A@mail.gmail.com/
Fixes: 5cb1ebdbc4 ("ice: Fix race condition during interface enslave")
Fixes: 4eace75e08 ("RDMA/irdma: Report the correct link speed")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230310194833.3074601-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable sending BIG TCP packets on IPv6 in the ice driver using generic
ipv6_hopopt_jumbo_remove helper for stripping HBH header.
Tested:
netperf -t TCP_RR -H 2001:db8:0:f101::1 -- -r80000,80000 -O MIN_LATENCY,P90_LATENCY,P99_LATENCY,TRANSACTION_RATE
Tested on two different setups. In both cases, the following settings were
applied after loading the changed driver:
ip link set dev enp175s0f1np1 gso_max_size 130000
ip link set dev enp175s0f1np1 gro_max_size 130000
ip link set dev enp175s0f1np1 mtu 9000
First setup:
Before:
Minimum 90th 99th Transaction
Latency Percentile Percentile Rate
Microseconds Latency Latency Tran/s
Microseconds Microseconds
134 279 410 3961.584
After:
Minimum 90th 99th Transaction
Latency Percentile Percentile Rate
Microseconds Latency Latency Tran/s
Microseconds Microseconds
135 178 216 6093.404
The other setup:
Before:
Minimum 90th 99th Transaction
Latency Percentile Percentile Rate
Microseconds Latency Latency Tran/s
Microseconds Microseconds
218 414 478 2944.765
After:
Minimum 90th 99th Transaction
Latency Percentile Percentile Rate
Microseconds Latency Latency Tran/s
Microseconds Microseconds
146 238 266 4700.596
Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Since mqprio is a scheduler and not a classifier, move its offload
structure to pkt_sched.h, where struct tc_taprio_qopt_offload also lies.
Also update some header inclusions in drivers that access this
structure, to the best of my abilities.
Cc: Igor Russkikh <irusskikh@marvell.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Saeed Mahameed <saeedm@nvidia.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: Daniel Machon <daniel.machon@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of code from probe can be reused in reload flow. Move this code to
separate function. Create unroll functions for each part of
initialization, like: ice_init_dev() and ice_deinit_dev(). It
simplifies unrolling and can be used in remove flow.
Avoid freeing port info as it could be reused in reload path.
Will be freed in remove path since is allocated via devm_kzalloc().
Also clean the remove path to reflect the init steps.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Do few small cleanups:
1) Rename the function to reflect that it doesn't configure all things
related to VSI. ice_vsi_cfg_lan() better fits to what function is doing.
ice_vsi_cfg() can be use to name function that will configure whole VSI.
2) Remove unused ethtype field from VSI. There is no need to set
ethtype here, because it is never used.
3) Remove unnecessary check for ICE_VSI_CHNL. There is check for
ICE_VSI_CHNL in ice_vsi_get_qs, so there is no need to check it before
calling the function.
4) Simplify ice_vsi_alloc() call. There is no need to check the type of
VSI before calling ice_vsi_alloc(). For ICE_VSI_CHNL vf is always NULL
(ice_vsi_setup() is called with vf=NULL).
For ICE_VSI_VF or ICE_VSI_CTRL ch is always NULL and for other VSI types
ch and vf are always NULL.
5) Remove unnecessary call to ice_vsi_dis_irq(). ice_vsi_dis_irq() will
be called in ice_vsi_close() flow (ice_vsi_close() -> ice_vsi_down() ->
ice_vsi_dis_irq()). Remove unnecessary call.
6) Don't remove specific filters in release. All hw filters are removed
in ice_fltr_remove_alli(), which is always called in VSI release flow.
There is no need to remove only ethertype filters before calling
ice_fltr_remove_all().
7) Rename ice_vsi_clear() to ice_vsi_free(). As ice_vsi_clear() only
free memory allocated in ice_vsi_alloc() rename it to ice_vsi_free()
which better shows what function is doing.
8) Free coalesce param in rebuild. There is potential memory leak if
configuration of VSI lan fails. Free coalesce to avoid it.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Simplify probe flow by moving all RDMA related code to ice_init_rdma().
Unroll irq allocation if RDMA initialization fails.
Implement ice_deinit_rdma() and use it in remove flow.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The PF controls the set of queues that the RDMA auxiliary_driver requests
resources from. The set_channel command will alter that pool and trigger a
reconfiguration of the VSI, which breaks RDMA functionality.
Prevent set_channel from executing when RDMA driver bound to auxiliary
device.
Adding a locked variable to pass down the call chain to avoid double
locking the device_lock.
Fixes: 348048e724 ("ice: Implement iidc operations")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Previously support for GNSS was implemented as a TTY driver, it allowed
to access GNSS receiver on /dev/ttyGNSS_<bus><func>.
Use generic GNSS subsystem API instead of implementing own TTY driver.
The receiver is accessible on /dev/gnss<id>. In case of multiple receivers
in the OS, correct device can be found by enumerating either:
- /sys/class/net/<eth port>/device/gnss/
- /sys/class/gnss/gnss<id>/device/
Using GNSS subsystem is superior to implementing own TTY driver, as the
GNSS subsystem was designed solely for this purpose. It also implements
TTY driver but in a common and defined way.
From user perspective, there is no difference in communicating with a
device, except new path to the device shall be used. The device will
provide same information to the userspace as the old one, and can be used
in the same way, i.e.:
old # gpsmon /dev/ttyGNSS_2100_0
new # gpsmon /dev/gnss0
There is no other impact on userspace tools.
User expecting onboard GNSS receiver support is required to enable
CONFIG_GNSS=y/m in kernel config.
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resets may occur with or without user interaction. For example, a TX hang
or reconfiguration of parameters will result in a reset. During reset, the
VSI is freed, freeing any statistics structures inside as well. This would
create an issue for the user where a reset happens in the background,
statistics set to zero, and the user checks ring statistics expecting them
to be populated.
To ensure this doesn't happen, accumulate ring statistics over reset.
Define a new ring statistics structure, ice_ring_stats. The new structure
lives in the VSI's parent, preserving ring statistics when VSI is freed.
1. Define a new structure vsi_ring_stats in the PF scope
2. Allocate/free stats only during probe, unload, or change in ring size
3. Replace previous ring statistics functionality with new structure
Signed-off-by: Benjamin Mikailenko <benjamin.mikailenko@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Resets happen with or without user interaction. For example, incidents
such as TX hang or a reconfiguration of parameters will result in a reset.
During reset, hardware and software statistics were set to zero. This
created an issue for the user where a reset happens in the background,
statistics set to zero, and the user checks statistics expecting them to
be populated.
To ensure this doesn't happen, keep accumulating stats over reset.
1. Remove function calls which reset hardware and netdev statistics.
2. Do not rollover statistics in ice_stat_update40 during reset.
Signed-off-by: Benjamin Mikailenko <benjamin.mikailenko@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add new VIRTCHNL_VF_OFFLOAD_RX_FLEX_DESC flag, opcode
VIRTCHNL_OP_GET_SUPPORTED_RXDIDS and add member rxdid
in struct virtchnl_rxq_info to support AVF Flex RXD
extension.
Add support to allow VF to query flexible descriptor RXDIDs supported
by DDP package and configure Rx queues with selected RXDID for IAVF.
Add code to allow VIRTCHNL_OP_GET_SUPPORTED_RXDIDS message to be
processed. Add necessary macros for registers.
Signed-off-by: Leyi Rong <leyi.rong@intel.com>
Signed-off-by: Xu Ting <ting.xu@intel.com>
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221025161252.1952939-1-jacob.e.keller@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch uses TC skbedit queue_mapping action to support
forwarding packets to a device queue. Such filters with action
forward to queue will be the highest priority switch filter in
HW.
Example:
$ tc filter add dev ens4f0 protocol ip ingress flower\
dst_ip 192.168.1.12 ip_proto tcp dst_port 5001\
action skbedit queue_mapping 5 skip_sw
The above command adds an ingress filter, incoming packets
qualifying the match will be accepted into queue 5. The queue
number is in decimal format.
Refactored ice_add_tc_flower_adv_fltr() to consolidate code with
action FWD_TO_VSI and FWD_TO QUEUE.
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Ice driver allocates per cpu XDP queues so that redirect path can safely
use smp_processor_id() as an index to the array. At the same time
though, XDP rings are used to pick NAPI context to call napi_schedule()
or set NAPIF_STATE_MISSED. When user reduces queue count, say to 8, and
num_possible_cpus() of underlying platform is 44, then this means queue
vectors with correlated NAPI contexts will carry several XDP queues.
This in turn can result in a broken behavior where NAPI context of
interest will never be scheduled and AF_XDP socket will not process any
traffic.
To fix this, let us change the way how XDP rings are assigned to Rx
rings and use this information later on when setting
ice_tx_ring::xsk_pool pointer. For each Rx ring, grab the associated
queue vector and walk through Tx ring's linked list. Once we stumble
upon XDP ring in it, assign this ring to ice_rx_ring::xdp_ring.
Previous [0] approach of fixing this issue was for txonly scenario
because of the described grouping of XDP rings across queue vectors. So,
relying on Rx ring meant that NAPI context could be scheduled with a
queue vector without XDP ring with associated XSK pool.
[0]: https://lore.kernel.org/netdev/20220707161128.54215-1-maciej.fijalkowski@intel.com/
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Fixes: 22bf877e52 ("ice: introduce XDP_TX fallback path")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
