Fix "double" clearing of interrupts, which can cause external events
or timestamps to be missed.
The E1000_TSIRC Time Sync Interrupt Cause register can be cleared in two
ways, by either reading it or by writing '1' into the specific cause
bit. This is documented in section 8.16.1.
The following flow was used:
1. read E1000_TSIRC into 'tsicr';
2. handle the interrupts present into 'tsirc' and mark them in 'ack';
3. write 'ack' into E1000_TSICR;
As both (1) and (3) will clear the interrupt cause, if the same
interrupt happens again between (1) and (3) it will be ignored,
causing events to be missed.
Remove the extra clear in (3).
Fixes: 00c65578b4 ("igb: enable internal PPS for the i210")
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Linux users sometimes need an easy way to check current values of module
parameters. For example the module may be manually reloaded with different
parameters. Make these visible and readable in the /sys filesystem to allow
that. But don't make the "debug" module parameter visible as debugging is
enabled via ethtool msglvl.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240301184806.2634508-2-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a cleanup patch, making code a bit more concise.
1) Use skb_network_offset(skb) in place of
(skb_network_header(skb) - skb->data)
2) Use -skb_network_offset(skb) in place of
(skb->data - skb_network_header(skb))
3) Use skb_transport_offset(skb) in place of
(skb_transport_header(skb) - skb->data)
4) Use skb_inner_transport_offset(skb) in place of
(skb_inner_transport_header(skb) - skb->data)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com> # for sfc
Signed-off-by: David S. Miller <davem@davemloft.net>
The i211 requires the same PTP timestamp adjustments as the i210,
according to its datasheet. To ensure consistent timestamping across
different platforms, this change extends the existing adjustments to
include the i211.
The adjustment result are tested and comparable for i210 and i211 based
systems.
Fixes: 3f544d2a4d ("igb: adjust PTP timestamps for Tx/Rx latency")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240227184942.362710-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make use of the existing linkmode helpers for converting PHY EEE
register values into links modes, now that ethtool_keee uses link
modes, rather than u32 values.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1978d3ead8 ("intel: fix string truncation warnings")
fixes '-Wformat-truncation=' warnings in igb_main.c by using kasprintf.
drivers/net/ethernet/intel/igb/igb_main.c:3092:53: warning:‘%d’ directive output may be truncated writing between 1 and 5 bytes into a region of size between 1 and 13 [-Wformat-truncation=]
3092 | "%d.%d, 0x%08x, %d.%d.%d",
| ^~
drivers/net/ethernet/intel/igb/igb_main.c:3092:34: note:directive argument in the range [0, 65535]
3092 | "%d.%d, 0x%08x, %d.%d.%d",
| ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/igb/igb_main.c:3092:34: note:directive argument in the range [0, 65535]
drivers/net/ethernet/intel/igb/igb_main.c:3090:25: note:‘snprintf’ output between 23 and 43 bytes into a destination of size 32
kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure.
Fix this warning by using a larger space for adapter->fw_version,
and then fall back and continue to use snprintf.
Fixes: 1978d3ead8 ("intel: fix string truncation warnings")
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Cc: Kunwu Chan <kunwu.chan@hotmail.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This is in preparation of using the existing names for linkmode
bitmaps.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor several older Intel drivers to use FIELD_GET(), which reduces
lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
@get@
constant shift,mask;
type T;
expression a;
@@
(
-((T)((a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
Cc: Julia Lawall <Julia.Lawall@inria.fr>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor several older Intel drivers to use FIELD_PREP(), which reduces
lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This series is introducing the use of FIELD_GET and FIELD_PREP which
requires bitfield.h to be included. Fix all the includes in this one
change, and rearrange includes into alphabetical order to ease
readability and future maintenance.
virtchnl.h and it's usage was modified to have it's own includes as it
should. This required including bits.h for virtchnl.h.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-12-12 (igb, e1000e)
This series contains updates to igb and e1000e drivers.
Ilpo Järvinen does some cleanups to both drivers: utilizing FIELD_GET()
helpers and using standard kernel defines over driver created ones.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
e1000e: Use pcie_capability_read_word() for reading LNKSTA
e1000e: Use PCI_EXP_LNKSTA_NLW & FIELD_GET() instead of custom defines/code
igb: Use FIELD_GET() to extract Link Width
====================
Link: https://lore.kernel.org/r/20231212204947.513563-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The get/set_rxfh ethtool ops currently takes the rxfh (RSS) parameters
as direct function arguments. This will force us to change the API (and
all drivers' functions) every time some new parameters are added.
This is part 1/2 of the fix, as suggested in [1]:
- First simplify the code by always providing a pointer to all params
(indir, key and func); the fact that some of them may be NULL seems
like a weird historic thing or a premature optimization.
It will simplify the drivers if all pointers are always present.
- Then make the functions take a dev pointer, and a pointer to a
single struct wrapping all arguments. The set_* should also take
an extack.
Link: https://lore.kernel.org/netdev/20231121152906.2dd5f487@kernel.org/ [1]
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-2-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use FIELD_GET() to extract PCIe Negotiated Link Width field instead of
custom masking and shifting.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This patch converts some basic cases of ethtool_sprintf() to
ethtool_puts().
The conversions are used in cases where ethtool_sprintf() was being used
with just two arguments:
| ethtool_sprintf(&data, buffer[i].name);
or when it's used with format string: "%s"
| ethtool_sprintf(&data, "%s", buffer[i].name);
which both now become:
| ethtool_puts(&data, buffer[i].name);
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add check for return of igb_update_ethtool_nfc_entry so that in case
of any potential errors the memory alocated for input will be freed.
Fixes: 0e71def252 ("igb: add support of RX network flow classification")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we exit a list_for_each_entry() without hitting a break statement,
the list iterator isn't NULL, it just point to an offset off the
list_head. In that situation, it wouldn't be too surprising for
entry->free to be true and we end up corrupting memory.
The way to test for these is to just set a flag.
Fixes: c1fec89045 ("ethernet/intel: Use list_for_each_entry() helper")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`strncpy` is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
We see that netdev->name is expected to be NUL-terminated based on its
usage with format strings:
| sprintf(q_vector->name, "%s-TxRx-%u", netdev->name,
| q_vector->rx.ring->queue_index);
Furthermore, NUL-padding is not required as netdev is already
zero-allocated:
| netdev = alloc_etherdev_mq(sizeof(struct igb_adapter),
| IGB_MAX_TX_QUEUES);
...
alloc_etherdev_mq() -> alloc_etherdev_mqs() -> alloc_netdev_mqs() ...
| p = kvzalloc(alloc_size, GFP_KERNEL_ACCOUNT | __GFP_RETRY_MAYFAIL);
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231017190411.2199743-8-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Get ahead of the game and fix all the -Wformat=2 noted warnings in the
intel drivers directory.
There are one set of i40e and iavf warnings I couldn't figure out how to
fix because the driver is already using vsnprintf without an explicit
"const char *" format string.
Tested with both gcc-12 and clang-15. I found gcc-12 runs clean after
this series but clang-15 is a little worried about the vsnprintf lines.
summary of warnings:
drivers/net/ethernet/intel/fm10k/fm10k_ethtool.c:148:34: warning: format string is not a string literal [-Wformat-nonliteral]
drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c:1416:24: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c:1416:24: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c:1421:6: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c:1421:6: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/igc/igc_ethtool.c:776:24: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/igc/igc_ethtool.c:776:24: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/igc/igc_ethtool.c:779:6: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/igc/igc_ethtool.c:779:6: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/iavf/iavf_ethtool.c:199:34: warning: format string is not a string literal [-Wformat-nonliteral]
drivers/net/ethernet/intel/igb/igb_ethtool.c:2360:6: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/igb/igb_ethtool.c:2360:6: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/igb/igb_ethtool.c:2363:6: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/igb/igb_ethtool.c:2363:6: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/i40e/i40e_ethtool.c:208:34: warning: format string is not a string literal [-Wformat-nonliteral]
drivers/net/ethernet/intel/i40e/i40e_ethtool.c:2515:23: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/i40e/i40e_ethtool.c:2515:23: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/i40e/i40e_ethtool.c:2519:23: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/i40e/i40e_ethtool.c:2519:23: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/ice/ice_ethtool.c:1064:6: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/ice/ice_ethtool.c:1064:6: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/ice/ice_ethtool.c:1084:6: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/ice/ice_ethtool.c:1084:6: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/ice/ice_ethtool.c:1100:24: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/ice/ice_ethtool.c:1100:24: note: treat the string as an argument to avoid this
Suggested-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231017190411.2199743-3-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix -Wformat-truncated warnings to complete the intel directories' W=1
clean efforts. The W=1 recently got enhanced with a few new flags and
this brought up some new warnings.
Switch to using kasprintf() when possible so we always allocate the
right length strings.
summary of warnings:
drivers/net/ethernet/intel/iavf/iavf_virtchnl.c:1425:60: warning: ‘%s’ directive output may be truncated writing 4 bytes into a region of size between 1 and 11 [-Wformat-truncation=]
drivers/net/ethernet/intel/iavf/iavf_virtchnl.c:1425:17: note: ‘snprintf’ output between 7 and 17 bytes into a destination of size 13
drivers/net/ethernet/intel/ice/ice_ptp.c:43:27: warning: ‘%s’ directive output may be truncated writing up to 479 bytes into a region of size 64 [-Wformat-truncation=]
drivers/net/ethernet/intel/ice/ice_ptp.c:42:17: note: ‘snprintf’ output between 1 and 480 bytes into a destination of size 64
drivers/net/ethernet/intel/igb/igb_main.c:3092:53: warning: ‘%d’ directive output may be truncated writing between 1 and 5 bytes into a region of size between 1 and 13 [-Wformat-truncation=]
drivers/net/ethernet/intel/igb/igb_main.c:3092:34: note: directive argument in the range [0, 65535]
drivers/net/ethernet/intel/igb/igb_main.c:3092:34: note: directive argument in the range [0, 65535]
drivers/net/ethernet/intel/igb/igb_main.c:3090:25: note: ‘snprintf’ output between 23 and 43 bytes into a destination of size 32
Suggested-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231017190411.2199743-2-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert list_for_each() to list_for_each_entry() where applicable.
No functional changed.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230919170409.1581074-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After commit 50f303496d ("igb: Enable SR-IOV after reinit"), removing
the igb module could hang or crash (depending on the machine) when the
module has been loaded with the max_vfs parameter set to some value != 0.
In case of one test machine with a dual port 82580, this hang occurred:
[ 232.480687] igb 0000:41:00.1: removed PHC on enp65s0f1
[ 233.093257] igb 0000:41:00.1: IOV Disabled
[ 233.329969] pcieport 0000:40:01.0: AER: Multiple Uncorrected (Non-Fatal) err0
[ 233.340302] igb 0000:41:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fata)
[ 233.352248] igb 0000:41:00.0: device [8086:1516] error status/mask=00100000
[ 233.361088] igb 0000:41:00.0: [20] UnsupReq (First)
[ 233.368183] igb 0000:41:00.0: AER: TLP Header: 40000001 0000040f cdbfc00c c
[ 233.376846] igb 0000:41:00.1: PCIe Bus Error: severity=Uncorrected (Non-Fata)
[ 233.388779] igb 0000:41:00.1: device [8086:1516] error status/mask=00100000
[ 233.397629] igb 0000:41:00.1: [20] UnsupReq (First)
[ 233.404736] igb 0000:41:00.1: AER: TLP Header: 40000001 0000040f cdbfc00c c
[ 233.538214] pci 0000:41:00.1: AER: can't recover (no error_detected callback)
[ 233.538401] igb 0000:41:00.0: removed PHC on enp65s0f0
[ 233.546197] pcieport 0000:40:01.0: AER: device recovery failed
[ 234.157244] igb 0000:41:00.0: IOV Disabled
[ 371.619705] INFO: task irq/35-aerdrv:257 blocked for more than 122 seconds.
[ 371.627489] Not tainted 6.4.0-dirty #2
[ 371.632257] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this.
[ 371.641000] task:irq/35-aerdrv state:D stack:0 pid:257 ppid:2 f0
[ 371.650330] Call Trace:
[ 371.653061] <TASK>
[ 371.655407] __schedule+0x20e/0x660
[ 371.659313] schedule+0x5a/0xd0
[ 371.662824] schedule_preempt_disabled+0x11/0x20
[ 371.667983] __mutex_lock.constprop.0+0x372/0x6c0
[ 371.673237] ? __pfx_aer_root_reset+0x10/0x10
[ 371.678105] report_error_detected+0x25/0x1c0
[ 371.682974] ? __pfx_report_normal_detected+0x10/0x10
[ 371.688618] pci_walk_bus+0x72/0x90
[ 371.692519] pcie_do_recovery+0xb2/0x330
[ 371.696899] aer_process_err_devices+0x117/0x170
[ 371.702055] aer_isr+0x1c0/0x1e0
[ 371.705661] ? __set_cpus_allowed_ptr+0x54/0xa0
[ 371.710723] ? __pfx_irq_thread_fn+0x10/0x10
[ 371.715496] irq_thread_fn+0x20/0x60
[ 371.719491] irq_thread+0xe6/0x1b0
[ 371.723291] ? __pfx_irq_thread_dtor+0x10/0x10
[ 371.728255] ? __pfx_irq_thread+0x10/0x10
[ 371.732731] kthread+0xe2/0x110
[ 371.736243] ? __pfx_kthread+0x10/0x10
[ 371.740430] ret_from_fork+0x2c/0x50
[ 371.744428] </TASK>
The reproducer was a simple script:
#!/bin/sh
for i in `seq 1 5`; do
modprobe -rv igb
modprobe -v igb max_vfs=1
sleep 1
modprobe -rv igb
done
It turned out that this could only be reproduce on 82580 (quad and
dual-port), but not on 82576, i350 and i210. Further debugging showed
that igb_enable_sriov()'s call to pci_enable_sriov() is failing, because
dev->is_physfn is 0 on 82580.
Prior to commit 50f303496d ("igb: Enable SR-IOV after reinit"),
igb_enable_sriov() jumped into the "err_out" cleanup branch. After this
commit it only returned the error code.
So the cleanup didn't take place, and the incorrect VF setup in the
igb_adapter structure fooled the igb driver into assuming that VFs have
been set up where no VF actually existed.
Fix this problem by cleaning up again if pci_enable_sriov() fails.
Fixes: 50f303496d ("igb: Enable SR-IOV after reinit")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the minimum value of RX/TX descriptors to 64 to enable setting the rx/tx
value between 64 and 80. All igb devices can use as low as 64 descriptors.
This change will unify igb with other drivers.
Based on commit 7b1be1987c ("e1000e: lower ring minimum size to 64")
Fixes: 9d5c824399 ("igb: PCI-Express 82575 Gigabit Ethernet driver")
Signed-off-by: Olga Zaborska <olga.zaborska@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Disable virtualization features on 82580 just as on i210/i211.
This avoids that virt functions are acidentally called on 82850.
Fixes: 55cac248ca ("igb: Add full support for 82580 devices")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the RX buffer size to 3K when the SBP bit is on. The size of
the RX buffer determines the number of pages allocated which may not
be sufficient for receive frames larger than the set MTU size.
Cc: stable@vger.kernel.org
Fixes: 89eaefb61d ("igb: Support RX-ALL feature flag.")
Reported-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As 32bits of dissector->used_keys are exhausted,
increase the size to 64bits.
This is base change for ESP/AH flow dissector patch.
Please find patch and discussions at
https://lore.kernel.org/netdev/ZMDNjD46BvZ5zp5I@corigine.com/T/#t
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Tested-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a setup where a Thunderbolt hub connects to Ethernet and a display
through USB Type-C, users may experience a hung task timeout when they
remove the cable between the PC and the Thunderbolt hub.
This is because the igb_down function is called multiple times when
the Thunderbolt hub is unplugged. For example, the igb_io_error_detected
triggers the first call, and the igb_remove triggers the second call.
The second call to igb_down will block at napi_synchronize.
Here's the call trace:
__schedule+0x3b0/0xddb
? __mod_timer+0x164/0x5d3
schedule+0x44/0xa8
schedule_timeout+0xb2/0x2a4
? run_local_timers+0x4e/0x4e
msleep+0x31/0x38
igb_down+0x12c/0x22a [igb 6615058754948bfde0bf01429257eb59f13030d4]
__igb_close+0x6f/0x9c [igb 6615058754948bfde0bf01429257eb59f13030d4]
igb_close+0x23/0x2b [igb 6615058754948bfde0bf01429257eb59f13030d4]
__dev_close_many+0x95/0xec
dev_close_many+0x6e/0x103
unregister_netdevice_many+0x105/0x5b1
unregister_netdevice_queue+0xc2/0x10d
unregister_netdev+0x1c/0x23
igb_remove+0xa7/0x11c [igb 6615058754948bfde0bf01429257eb59f13030d4]
pci_device_remove+0x3f/0x9c
device_release_driver_internal+0xfe/0x1b4
pci_stop_bus_device+0x5b/0x7f
pci_stop_bus_device+0x30/0x7f
pci_stop_bus_device+0x30/0x7f
pci_stop_and_remove_bus_device+0x12/0x19
pciehp_unconfigure_device+0x76/0xe9
pciehp_disable_slot+0x6e/0x131
pciehp_handle_presence_or_link_change+0x7a/0x3f7
pciehp_ist+0xbe/0x194
irq_thread_fn+0x22/0x4d
? irq_thread+0x1fd/0x1fd
irq_thread+0x17b/0x1fd
? irq_forced_thread_fn+0x5f/0x5f
kthread+0x142/0x153
? __irq_get_irqchip_state+0x46/0x46
? kthread_associate_blkcg+0x71/0x71
ret_from_fork+0x1f/0x30
In this case, igb_io_error_detected detaches the network interface
and requests a PCIE slot reset, however, the PCIE reset callback is
not being invoked and thus the Ethernet connection breaks down.
As the PCIE error in this case is a non-fatal one, requesting a
slot reset can be avoided.
This patch fixes the task hung issue and preserves Ethernet
connection by ignoring non-fatal PCIE errors.
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230620174732.4145155-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add error handling into igb_set_eeprom() function, in case
nvm.ops.read() fails just quit with error code asap.
Fixes: 9d5c824399 ("igb: PCI-Express 82575 Gigabit Ethernet driver")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
82580/i354/i350 features circle-counter-like timestamp registers
that are different with newer i210. The EXTTS capture value in
AUXTSMPx should be converted from raw circle counter value to
timestamp value in resolution of 1 nanosec by the driver.
This issue can be reproduced on i350 nics, connecting an 1PPS
signal to a SDP pin, and run 'ts2phc' command to read external
1PPS timestamp value. On i210 this works fine, but on i350 the
extts is not correctly converted.
The i350/i354/82580's SYSTIM and other timestamp registers are
40bit counters, presenting time range of 2^40 ns, that means these
registers overflows every about 1099s. This causes all these regs
can't be used directly in contrast to the newer i210/i211s.
The igb driver needs to convert these raw register values to
valid time stamp format by using kernel timecounter apis for i350s
families. Here the igb_extts() just forgot to do the convert.
Fixes: 38970eac41 ("igb: support EXTTS on 82580/i354/i350")
Signed-off-by: Yuezhen Luan <eggcar.luan@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230607164116.3768175-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-05-18 (igc, igb, e1000e)
This series contains updates to igc, igb, and e1000e drivers.
Kurt Kanzenbach adds calls to txq_trans_cond_update() for XDP transmit
on igc.
Tom Rix makes definition of igb_pm_ops conditional on CONFIG_PM for igb.
Baozhu Ni adds a missing kdoc description on e1000e.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
e1000e: Add @adapter description to kdoc
igb: Define igb_pm_ops conditionally on CONFIG_PM
igc: Avoid transmit queue timeout for XDP
====================
Link: https://lore.kernel.org/r/20230518170942.418109-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For s390, gcc with W=1 reports
drivers/net/ethernet/intel/igb/igb_main.c:186:32: error:
'igb_pm_ops' defined but not used [-Werror=unused-const-variable=]
186 | static const struct dev_pm_ops igb_pm_ops = {
| ^~~~~~~~~~
The only use of igb_pm_ops is conditional on CONFIG_PM.
The definition of igb_pm_ops should also be conditional on CONFIG_PM
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In igb_hash_mc_addr() the expression:
"mc_addr[4] >> 8 - bit_shift", right shifting "mc_addr[4]"
shift by more than 7 bits always yields zero, so hash becomes not so different.
Add initialization with bit_shift = 1 and add a loop condition to ensure
bit_shift will be always in [1..8] range.
Fixes: 9d5c824399 ("igb: PCI-Express 82575 Gigabit Ethernet driver")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver's .adjfine interface functions use adjust_by_scaled_ppm and
diff_by_scaled_ppm introduced in commit 1060707e38
("ptp: introduce helpers to adjust by scaled parts per million")
to calculate the required adjustment in a concise manner,
but not igb_ptp_adjfine_82580.
Fix it by introducing IGB_82580_BASE_PERIOD and changing function logic
to use diff_by_scaled_ppm.
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Enabling SR-IOV causes the virtual functions to make requests to the
PF via the mailbox. Notably, E1000_VF_RESET request will happen during
the initialization of the VF. However, unless the reinit is done, the
VMMB interrupt, which delivers mailbox interrupt from VF to PF will be
kept masked and such requests will be silently ignored.
Enable SR-IOV at the very end of the procedure to configure the device
for SR-IOV so that the PF is configured properly for SR-IOV when a VF is
activated.
Fixes: fa44f2f185 ("igb: Enable SR-IOV configuration via PCI sysfs interface")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit a97f8783a9 ("igb: unbreak I2C bit-banging on i350") introduced
code to change I2C settings to bit banging unconditionally.
However, this patch introduced a regression: On an Intel S2600CWR
Server Board with three NICs:
- 1x dual-port copper
Intel I350 Gigabit Network Connection [8086:1521] (rev 01)
fw 1.63, 0x80000dda
- 2x quad-port SFP+ with copper SFP Avago ABCU-5700RZ
Intel I350 Gigabit Fiber Network Connection [8086:1522] (rev 01)
fw 1.52.0
the SFP NICs no longer get link at all. Reverting commit a97f8783a9
or switching to the Intel out-of-tree driver both fix the problem.
Per the igb out-of-tree driver, I2C bit banging on i350 depends on
support for an external thermal sensor (ETS). However, commit
a97f8783a9 added bit banging unconditionally. Additionally, the
out-of-tree driver always calls init_thermal_sensor_thresh on probe,
while our driver only calls init_thermal_sensor_thresh only in
igb_reset(), and only if an ETS is present, ignoring the internal
thermal sensor. The affected SFPs don't provide an ETS. Per Intel,
the behaviour is a result of i350 firmware requirements.
This patch fixes the problem by aligning the behaviour to the
out-of-tree driver:
- split igb_init_i2c() into two functions:
- igb_init_i2c() only performs the basic I2C initialization.
- igb_set_i2c_bb() makes sure that E1000_CTRL_I2C_ENA is set
and enables bit-banging.
- igb_probe() only calls igb_set_i2c_bb() if an ETS is present.
- igb_probe() calls init_thermal_sensor_thresh() unconditionally.
- igb_reset() aligns its behaviour to igb_probe(), i. e., call
igb_set_i2c_bb() if an ETS is present and call
init_thermal_sensor_thresh() unconditionally.
Fixes: a97f8783a9 ("igb: unbreak I2C bit-banging on i350")
Tested-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Co-developed-by: Jamie Bainbridge <jbainbri@redhat.com>
Signed-off-by: Jamie Bainbridge <jbainbri@redhat.com>
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230214185549.1306522-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix handling of the tsync interrupt to compare the pin number with
IGB_N_SDP instead of IGB_N_EXTTS/IGB_N_PEROUT and fix the indexing to
the perout array.
Fixes: cf99c1dd7b ("igb: move PEROUT and EXTTS isr logic to separate functions")
Reported-by: Matt Corallo <ntp-lists@mattcorallo.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230213185822.3960072-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCY+bZrwAKCRDbK58LschI
gzi4AP4+TYo0jnSwwkrOoN9l4f5VO9X8osmj3CXfHBv7BGWVxAD/WnvA3TDZyaUd
agIZTkRs6BHF9He8oROypARZxTeMLwM=
=nO1C
-----END PGP SIGNATURE-----
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-02-11
We've added 96 non-merge commits during the last 14 day(s) which contain
a total of 152 files changed, 4884 insertions(+), 962 deletions(-).
There is a minor conflict in drivers/net/ethernet/intel/ice/ice_main.c
between commit 5b246e533d ("ice: split probe into smaller functions")
from the net-next tree and commit 66c0e13ad2 ("drivers: net: turn on
XDP features") from the bpf-next tree. Remove the hunk given ice_cfg_netdev()
is otherwise there a 2nd time, and add XDP features to the existing
ice_cfg_netdev() one:
[...]
ice_set_netdev_features(netdev);
netdev->xdp_features = NETDEV_XDP_ACT_BASIC | NETDEV_XDP_ACT_REDIRECT |
NETDEV_XDP_ACT_XSK_ZEROCOPY;
ice_set_ops(netdev);
[...]
Stephen's merge conflict mail:
https://lore.kernel.org/bpf/20230207101951.21a114fa@canb.auug.org.au/
The main changes are:
1) Add support for BPF trampoline on s390x which finally allows to remove many
test cases from the BPF CI's DENYLIST.s390x, from Ilya Leoshkevich.
2) Add multi-buffer XDP support to ice driver, from Maciej Fijalkowski.
3) Add capability to export the XDP features supported by the NIC.
Along with that, add a XDP compliance test tool,
from Lorenzo Bianconi & Marek Majtyka.
4) Add __bpf_kfunc tag for marking kernel functions as kfuncs,
from David Vernet.
5) Add a deep dive documentation about the verifier's register
liveness tracking algorithm, from Eduard Zingerman.
6) Fix and follow-up cleanups for resolve_btfids to be compiled
as a host program to avoid cross compile issues,
from Jiri Olsa & Ian Rogers.
7) Batch of fixes to the BPF selftest for xdp_hw_metadata which resulted
when testing on different NICs, from Jesper Dangaard Brouer.
8) Fix libbpf to better detect kernel version code on Debian, from Hao Xiang.
9) Extend libbpf to add an option for when the perf buffer should
wake up, from Jon Doron.
10) Follow-up fix on xdp_metadata selftest to just consume on TX
completion, from Stanislav Fomichev.
11) Extend the kfuncs.rst document with description on kfunc
lifecycle & stability expectations, from David Vernet.
12) Fix bpftool prog profile to skip attaching to offline CPUs,
from Tonghao Zhang.
====================
Link: https://lore.kernel.org/r/20230211002037.8489-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current taprio software implementation is haunted by the shadow of the
igb/igc hardware model. It iterates over child qdiscs in increasing
order of TXQ index, therefore giving higher xmit priority to TXQ 0 and
lower to TXQ N. According to discussions with Vinicius, that is the
default (perhaps even unchangeable) prioritization scheme used for the
NICs that taprio was first written for (igb, igc), and we have a case of
two bugs canceling out, resulting in a functional setup on igb/igc, but
a less sane one on other NICs.
To the best of my understanding, taprio should prioritize based on the
traffic class, so it should really dequeue starting with the highest
traffic class and going down from there. We get to the TXQ using the
tc_to_txq[] netdev property.
TXQs within the same TC have the same (strict) priority, so we should
pick from them as fairly as we can. We can achieve that by implementing
something very similar to q->curband from multiq_dequeue().
Since igb/igc really do have TXQ 0 of higher hardware priority than
TXQ 1 etc, we need to preserve the behavior for them as well. We really
have no choice, because in txtime-assist mode, taprio is essentially a
software scheduler towards offloaded child tc-etf qdiscs, so the TXQ
selection really does matter (not all igb TXQs support ETF/SO_TXTIME,
says Kurt Kanzenbach).
To preserve the behavior, we need a capability bit so that taprio can
determine if it's running on igb/igc, or on something else. Because igb
doesn't offload taprio at all, we can't piggyback on the
qdisc_offload_query_caps() call from taprio_enable_offload(), but
instead we need a separate call which is also made for software
scheduling.
Introduce two static keys to minimize the performance penalty on systems
which only have igb/igc NICs, and on systems which only have other NICs.
For mixed systems, taprio will have to dynamically check whether to
dequeue using one prioritization algorithm or using the other.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>