The TDX module global metadata provides system-wide information about
the module.
TL;DR:
Use the TDH.SYS.RD SEAMCALL to tell if the module is good or not.
Long Version:
1) Only initialize TDX module with version 1.5 and later
TDX module 1.0 has some compatibility issues with the later versions of
module, as documented in the "Intel TDX module ABI incompatibilities
between TDX1.0 and TDX1.5" spec. Don't bother with module versions that
do not have a stable ABI.
2) Get the essential global metadata for module initialization
TDX reports a list of "Convertible Memory Region" (CMR) to tell the
kernel which memory is TDX compatible. The kernel needs to build a list
of memory regions (out of CMRs) as "TDX-usable" memory and pass them to
the TDX module. The kernel does this by constructing a list of "TD
Memory Regions" (TDMRs) to cover all these memory regions and passing
them to the TDX module.
Each TDMR is a TDX architectural data structure containing the memory
region that the TDMR covers, plus the information to track (within this
TDMR):
a) the "Physical Address Metadata Table" (PAMT) to track each TDX
memory page's status (such as which TDX guest "owns" a given page,
and
b) the "reserved areas" to tell memory holes that cannot be used as
TDX memory.
The kernel needs to get below metadata from the TDX module to build the
list of TDMRs:
a) the maximum number of supported TDMRs
b) the maximum number of supported reserved areas per TDMR and,
c) the PAMT entry size for each TDX-supported page size.
== Implementation ==
The TDX module has two modes of fetching the metadata: a one field at
a time, or all in one blob. Use the field at a time for now. It is
slower, but there just are not enough fields now to justify the
complexity of extra unpacking.
The err_free_tdxmem=>out_put_tdxmem goto looks wonky by itself. But
it is the first of a bunch of error handling that will get stuck at
its site.
[ dhansen: clean up changelog and add a struct to map between
the TDX module fields and 'struct tdx_tdmr_sysinfo' ]
Signed-off-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/20231208170740.53979-8-dave.hansen%40intel.com
TDX supports 4K, 2M and 1G page sizes. The corresponding values are
defined by the TDX module spec and used as TDX module ABI. Currently,
they are used in try_accept_one() when the TDX guest tries to accept a
page. However currently try_accept_one() uses hard-coded magic values.
Define TDX supported page sizes as macros and get rid of the hard-coded
values in try_accept_one(). TDX host support will need to use them too.
Signed-off-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/all/20231208170740.53979-2-dave.hansen%40intel.com
- Introduce configfs-tsm as a shared ABI for confidential computing
attestation reports
- Convert sev-guest to additionally support configfs-tsm alongside its
vendor specific ioctl()
- Added signed attestation report retrieval to the tdx-guest driver
forgoing a new vendor specific ioctl()
- Misc. cleanups and a new __free() annotation for kvfree()
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSbo+XnGs+rwLz9XGXfioYZHlFsZwUCZUQhiQAKCRDfioYZHlFs
Z2gMAQCJdtP0f2kH+pvf3oxAkA1OubKBqJqWOppeyrhTsNMpDQEA9ljXH9h7eRB/
2NQ6USrU6jqcdu3gB5Tzq8J/ZZabMQU=
=1Eiv
-----END PGP SIGNATURE-----
Merge tag 'tsm-for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/linux
Pull unified attestation reporting from Dan Williams:
"In an ideal world there would be a cross-vendor standard attestation
report format for confidential guests along with a common device
definition to act as the transport.
In the real world the situation ended up with multiple platform
vendors inventing their own attestation report formats with the
SEV-SNP implementation being a first mover to define a custom
sev-guest character device and corresponding ioctl(). Later, this
configfs-tsm proposal intercepted an attempt to add a tdx-guest
character device and a corresponding new ioctl(). It also anticipated
ARM and RISC-V showing up with more chardevs and more ioctls().
The proposal takes for granted that Linux tolerates the vendor report
format differentiation until a standard arrives. From talking with
folks involved, it sounds like that standardization work is unlikely
to resolve anytime soon. It also takes the position that kernfs ABIs
are easier to maintain than ioctl(). The result is a shared configfs
mechanism to return per-vendor report-blobs with the option to later
support a standard when that arrives.
Part of the goal here also is to get the community into the
"uncomfortable, but beneficial to the long term maintainability of the
kernel" state of talking to each other about their differentiation and
opportunities to collaborate. Think of this like the device-driver
equivalent of the common memory-management infrastructure for
confidential-computing being built up in KVM.
As for establishing an "upstream path for cross-vendor
confidential-computing device driver infrastructure" this is something
I want to discuss at Plumbers. At present, the multiple vendor
proposals for assigning devices to confidential computing VMs likely
needs a new dedicated repository and maintainer team, but that is a
discussion for v6.8.
For now, Greg and Thomas have acked this approach and this is passing
is AMD, Intel, and Google tests.
Summary:
- Introduce configfs-tsm as a shared ABI for confidential computing
attestation reports
- Convert sev-guest to additionally support configfs-tsm alongside
its vendor specific ioctl()
- Added signed attestation report retrieval to the tdx-guest driver
forgoing a new vendor specific ioctl()
- Misc cleanups and a new __free() annotation for kvfree()"
* tag 'tsm-for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/linux:
virt: tdx-guest: Add Quote generation support using TSM_REPORTS
virt: sevguest: Add TSM_REPORTS support for SNP_GET_EXT_REPORT
mm/slab: Add __free() support for kvfree
virt: sevguest: Prep for kernel internal get_ext_report()
configfs-tsm: Introduce a shared ABI for attestation reports
virt: coco: Add a coco/Makefile and coco/Kconfig
virt: sevguest: Fix passing a stack buffer as a scatterlist target
In TDX guest, the attestation process is used to verify the TDX guest
trustworthiness to other entities before provisioning secrets to the
guest. The first step in the attestation process is TDREPORT
generation, which involves getting the guest measurement data in the
format of TDREPORT, which is further used to validate the authenticity
of the TDX guest. TDREPORT by design is integrity-protected and can
only be verified on the local machine.
To support remote verification of the TDREPORT in a SGX-based
attestation, the TDREPORT needs to be sent to the SGX Quoting Enclave
(QE) to convert it to a remotely verifiable Quote. SGX QE by design can
only run outside of the TDX guest (i.e. in a host process or in a
normal VM) and guest can use communication channels like vsock or
TCP/IP to send the TDREPORT to the QE. But for security concerns, the
TDX guest may not support these communication channels. To handle such
cases, TDX defines a GetQuote hypercall which can be used by the guest
to request the host VMM to communicate with the SGX QE. More details
about GetQuote hypercall can be found in TDX Guest-Host Communication
Interface (GHCI) for Intel TDX 1.0, section titled
"TDG.VP.VMCALL<GetQuote>".
Trusted Security Module (TSM) [1] exposes a common ABI for Confidential
Computing Guest platforms to get the measurement data via ConfigFS.
Extend the TSM framework and add support to allow an attestation agent
to get the TDX Quote data (included usage example below).
report=/sys/kernel/config/tsm/report/report0
mkdir $report
dd if=/dev/urandom bs=64 count=1 > $report/inblob
hexdump -C $report/outblob
rmdir $report
GetQuote TDVMCALL requires TD guest pass a 4K aligned shared buffer
with TDREPORT data as input, which is further used by the VMM to copy
the TD Quote result after successful Quote generation. To create the
shared buffer, allocate a large enough memory and mark it shared using
set_memory_decrypted() in tdx_guest_init(). This buffer will be re-used
for GetQuote requests in the TDX TSM handler.
Although this method reserves a fixed chunk of memory for GetQuote
requests, such one time allocation can help avoid memory fragmentation
related allocation failures later in the uptime of the guest.
Since the Quote generation process is not time-critical or frequently
used, the current version uses a polling model for Quote requests and
it also does not support parallel GetQuote requests.
Link: https://lore.kernel.org/lkml/169342399185.3934343.3035845348326944519.stgit@dwillia2-xfh.jf.intel.com/ [1]
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Erdem Aktas <erdemaktas@google.com>
Tested-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Peter Gonda <pgonda@google.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
LKP reported below build warning:
vmlinux.o: warning: objtool: __tdx_hypercall+0x128: __tdx_hypercall_failed() is missing a __noreturn annotation
The __tdx_hypercall_failed() function definition already has __noreturn
annotation, but it turns out the __noreturn must be annotated to the
function declaration.
PeterZ explains:
"FWIW, the reason being that...
The point of noreturn is that the caller should know to stop generating
code. For that the declaration needs the attribute, because call sites
typically do not have access to the function definition in C."
Add __noreturn annotation to the declaration of __tdx_hypercall_failed()
to fix. It's not a bad idea to document the __noreturn nature at the
definition site either, so keep the annotation at the definition.
Note <asm/shared/tdx.h> is also included by TDX related assembly files.
Include <linux/compiler_attributes.h> only in case of !__ASSEMBLY__
otherwise compiling assembly file would trigger build error.
Also, following the objtool documentation, add __tdx_hypercall_failed()
to "tools/objtool/noreturns.h".
Fixes: c641cfb5c1 ("x86/tdx: Make TDX_HYPERCALL asm similar to TDX_MODULE_CALL")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230918041858.331234-1-kai.huang@intel.com
Closes: https://lore.kernel.org/oe-kbuild-all/202309140828.9RdmlH2Z-lkp@intel.com/
Now 'struct tdx_hypercall_args' is basically 'struct tdx_module_args'
minus RCX. Although from __tdx_hypercall()'s perspective RCX isn't
used as shared register thus not part of input/output registers, it's
not worth to have a separate structure just due to one register.
Remove the 'struct tdx_hypercall_args' and use 'struct tdx_module_args'
instead in __tdx_hypercall() related code. This also saves the memory
copy between the two structures within __tdx_hypercall().
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/798dad5ce24e9d745cf0e16825b75ccc433ad065.1692096753.git.kai.huang%40intel.com
Now the TDX_HYPERCALL asm is basically identical to the TDX_MODULE_CALL
with both '\saved' and '\ret' enabled, with two minor things though:
1) The way to restore the structure pointer is different
The TDX_HYPERCALL uses RCX as spare to restore the structure pointer,
but the TDX_MODULE_CALL assumes no spare register can be used. In other
words, TDX_MODULE_CALL already covers what TDX_HYPERCALL does.
2) TDX_MODULE_CALL only clears shared registers for TDH.VP.ENTER
For this just need to make that code available for the non-host case.
Thus, remove the TDX_HYPERCALL and reimplement the __tdx_hypercall()
using the TDX_MODULE_CALL.
Extend the TDX_MODULE_CALL to cover "clear shared registers" for
TDG.VP.VMCALL. Introduce a new __tdcall_saved_ret() to replace the
temporary __tdcall_hypercall().
The __tdcall_saved_ret() can also be used for those new TDCALLs which
require more input/output registers than the basic TDCALLs do.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/e68a2473fb6f5bcd78b078cae7510e9d0753b3df.1692096753.git.kai.huang%40intel.com
Now the 'struct tdx_hypercall_args' and 'struct tdx_module_args' are
almost the same, and the TDX_HYPERCALL and TDX_MODULE_CALL asm macro
share similar code pattern too. The __tdx_hypercall() and __tdcall()
should be unified to use the same assembly code.
As a preparation to unify them, simplify the TDX_HYPERCALL to make it
more like the TDX_MODULE_CALL.
The TDX_HYPERCALL takes the pointer of 'struct tdx_hypercall_args' as
function call argument, and does below extra things comparing to the
TDX_MODULE_CALL:
1) It sets RAX to 0 (TDG.VP.VMCALL leaf) internally;
2) It sets RCX to the (fixed) bitmap of shared registers internally;
3) It calls __tdx_hypercall_failed() internally (and panics) when the
TDCALL instruction itself fails;
4) After TDCALL, it moves R10 to RAX to return the return code of the
VMCALL leaf, regardless the '\ret' asm macro argument;
Firstly, change the TDX_HYPERCALL to take the same function call
arguments as the TDX_MODULE_CALL does: TDCALL leaf ID, and the pointer
to 'struct tdx_module_args'. Then 1) and 2) can be moved to the
caller:
- TDG.VP.VMCALL leaf ID can be passed via the function call argument;
- 'struct tdx_module_args' is 'struct tdx_hypercall_args' + RCX, thus
the bitmap of shared registers can be passed via RCX in the
structure.
Secondly, to move 3) and 4) out of assembly, make the TDX_HYPERCALL
always save output registers to the structure. The caller then can:
- Call __tdx_hypercall_failed() when TDX_HYPERCALL returns error;
- Return R10 in the structure as the return code of the VMCALL leaf;
With above changes, change the asm function from __tdx_hypercall() to
__tdcall_hypercall(), and reimplement __tdx_hypercall() as the C wrapper
of it. This avoids having to add another wrapper of __tdx_hypercall()
(_tdx_hypercall() is already taken).
The __tdcall_hypercall() will be replaced with a __tdcall() variant
using TDX_MODULE_CALL in a later commit as the final goal is to have one
assembly to handle both TDCALL and TDVMCALL.
Currently, the __tdx_hypercall() asm is in '.noinstr.text'. To keep
this unchanged, annotate __tdx_hypercall(), which is a C function now,
as 'noinstr'.
Remove the __tdx_hypercall_ret() as __tdx_hypercall() already does so.
Implement __tdx_hypercall() in tdx-shared.c so it can be shared with the
compressed code.
Opportunistically fix a checkpatch error complaining using space around
parenthesis '(' and ')' while moving the bitmap of shared registers to
<asm/shared/tdx.h>.
[ dhansen: quash new calls of __tdx_hypercall_ret() that showed up ]
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/0cbf25e7aee3256288045023a31f65f0cef90af4.1692096753.git.kai.huang%40intel.com
The TDX guest live migration support (TDX 1.5) adds new TDCALL/SEAMCALL
leaf functions. Those new TDCALLs/SEAMCALLs take additional registers
for input (R10-R13) and output (R12-R13). TDG.SERVTD.RD is an example.
Also, the current TDX_MODULE_CALL doesn't aim to handle TDH.VP.ENTER
SEAMCALL, which monitors the TDG.VP.VMCALL in input/output registers
when it returns in case of VMCALL from TDX guest.
With those new TDCALLs/SEAMCALLs and the TDH.VP.ENTER covered, the
TDX_MODULE_CALL macro basically needs to handle the same input/output
registers as the TDX_HYPERCALL does. And as a result, they also share
similar logic in the assembly, thus should be unified to use one common
assembly.
Extend the TDX_MODULE_CALL asm to support the new TDCALLs/SEAMCALLs and
also the TDH.VP.ENTER SEAMCALL. Eventually it will be unified with the
TDX_HYPERCALL.
The new input/output registers fit with the "callee-saved" registers in
the x86 calling convention. Add a new "saved" parameter to support
those new TDCALLs/SEAMCALLs and TDH.VP.ENTER and keep the existing
TDCALLs/SEAMCALLs minimally impacted.
For TDH.VP.ENTER, after it returns the registers shared by the guest
contain guest's values. Explicitly clear them to prevent speculative
use of guest's values.
Note most TDX live migration related SEAMCALLs may also clobber AVX*
state ("AVX, AVX2 and AVX512 state: may be reset to the architectural
INIT state" -- see TDH.EXPORT.MEM for example). And TDH.VP.ENTER also
clobbers XMM0-XMM15 when the corresponding bit is set in RCX. Don't
handle them in the TDX_MODULE_CALL macro but let the caller save and
restore when needed.
This is basically based on Peter's code.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/d4785de7c392f7c5684407f6c24a73b92148ec49.1692096753.git.kai.huang%40intel.com
Currently, the TDX_MODULE_CALL asm macro, which handles both TDCALL and
SEAMCALL, takes one parameter for each input register and an optional
'struct tdx_module_output' (a collection of output registers) as output.
This is different from the TDX_HYPERCALL macro which uses a single
'struct tdx_hypercall_args' to carry all input/output registers.
The newer TDX versions introduce more TDCALLs/SEAMCALLs which use more
input/output registers. Also, the TDH.VP.ENTER (which isn't covered
by the current TDX_MODULE_CALL macro) basically can use all registers
that the TDX_HYPERCALL does. The current TDX_MODULE_CALL macro isn't
extendible to cover those cases.
Similar to the TDX_HYPERCALL macro, simplify the TDX_MODULE_CALL macro
to use a single structure 'struct tdx_module_args' to carry all the
input/output registers. Currently, R10/R11 are only used as output
register but not as input by any TDCALL/SEAMCALL. Change to also use
R10/R11 as input register to make input/output registers symmetric.
Currently, the TDX_MODULE_CALL macro depends on the caller to pass a
non-NULL 'struct tdx_module_output' to get additional output registers.
Similar to the TDX_HYPERCALL macro, change the TDX_MODULE_CALL macro to
take a new 'ret' macro argument to indicate whether to save the output
registers to the 'struct tdx_module_args'. Also introduce a new
__tdcall_ret() for that purpose, similar to the __tdx_hypercall_ret().
Note the tdcall(), which is a wrapper of __tdcall(), is called by three
callers: tdx_parse_tdinfo(), tdx_get_ve_info() and tdx_early_init().
The former two need the additional output but the last one doesn't. For
simplicity, make tdcall() always call __tdcall_ret() to avoid another
"_ret()" wrapper. The last caller tdx_early_init() isn't performance
critical anyway.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/483616c1762d85eb3a3c3035a7de061cfacf2f14.1692096753.git.kai.huang%40intel.com
__tdx_module_call() is only used by the TDX guest to issue TDCALL to the
TDX module. Rename it to __tdcall() to match its behaviour, e.g., it
cannot be used to make host-side SEAMCALL.
Also rename tdx_module_call() which is a wrapper of __tdx_module_call()
to tdcall().
No functional change intended.
Signed-off-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/785d20d99fbcd0db8262c94da6423375422d8c75.1692096753.git.kai.huang%40intel.com
The TDX spec names all TDCALLs with prefix "TDG". Currently, the kernel
doesn't follow such convention for the macros of those TDCALLs but uses
prefix "TDX_" for all of them. Although it's arguable whether the TDX
spec names those TDCALLs properly, it's better for the kernel to follow
the spec when naming those macros.
Change all macros of TDCALLs to make them consistent with the spec. As
a bonus, they get distinguished easily from the host-side SEAMCALLs,
which all have prefix "TDH".
No functional change intended.
Signed-off-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/516dccd0bd8fb9a0b6af30d25bb2d971aa03d598.1692096753.git.kai.huang%40intel.com
TDX guest memory is private by default and the VMM may not access it.
However, in cases where the guest needs to share data with the VMM,
the guest and the VMM can coordinate to make memory shared between
them.
The guest side of this protocol includes the "MapGPA" hypercall. This
call takes a guest physical address range. The hypercall spec (aka.
the GHCI) says that the MapGPA call is allowed to return partial
progress in mapping this range and indicate that fact with a special
error code. A guest that sees such partial progress is expected to
retry the operation for the portion of the address range that was not
completed.
Hyper-V does this partial completion dance when set_memory_decrypted()
is called to "decrypt" swiotlb bounce buffers that can be up to 1GB
in size. It is evidently the only VMM that does this, which is why
nobody noticed this until now.
[ dhansen: rewrite changelog ]
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: https://lore.kernel.org/all/20230811021246.821-2-decui%40microsoft.com
a fatal shutdown during TDX private<=>shared conversion
- Annotate sites where VM "exit reasons" are reused as hypercall
numbers.
-----BEGIN PGP SIGNATURE-----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=Hr3D
-----END PGP SIGNATURE-----
Merge tag 'x86_tdx_for_6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 tdx updates from Dave Hansen:
- Fix a race window where load_unaligned_zeropad() could cause a fatal
shutdown during TDX private<=>shared conversion
The race has never been observed in practice but might allow
load_unaligned_zeropad() to catch a TDX page in the middle of its
conversion process which would lead to a fatal and unrecoverable
guest shutdown.
- Annotate sites where VM "exit reasons" are reused as hypercall
numbers.
* tag 'x86_tdx_for_6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix enc_status_change_finish_noop()
x86/tdx: Fix race between set_memory_encrypted() and load_unaligned_zeropad()
x86/mm: Allow guest.enc_status_change_prepare() to fail
x86/tdx: Wrap exit reason with hcall_func()
Hookup TDX-specific code to accept memory.
Accepting the memory is done with ACCEPT_PAGE module call on every page
in the range. MAP_GPA hypercall is not required as the unaccepted memory
is considered private already.
Extract the part of tdx_enc_status_changed() that does memory acceptance
in a new helper. Move the helper tdx-shared.c. It is going to be used by
both main kernel and decompressor.
[ bp: Fix the INTEL_TDX_GUEST=y, KVM_GUEST=n build. ]
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230606142637.5171-10-kirill.shutemov@linux.intel.com
Memory acceptance requires a hypercall and one or multiple module calls.
Make helpers for the calls available in boot stub. It has to accept
memory where kernel image and initrd are placed.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/20230606142637.5171-8-kirill.shutemov@linux.intel.com
TDX reuses VMEXIT "reasons" in its guest->host hypercall ABI. This is
confusing because there might not be a VMEXIT involved at *all*.
These instances are supposed to document situation and reduce confusion
by wrapping VMEXIT reasons with hcall_func().
The decompression code does not follow this convention.
Unify the TDX decompression code with the other TDX use of VMEXIT reasons.
No functional changes.
Signed-off-by: Nikolay Borisov <nik.borisov@suse.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: https://lore.kernel.org/all/20230505120332.1429957-1-nik.borisov%40suse.com
After TDX_HCALL_ISSUE_STI got dropped, the only flag left is
TDX_HCALL_HAS_OUTPUT. The flag indicates if the caller wants to see
tdx_hypercall_args updated based on the hypercall output.
Drop the flags and provide __tdx_hypercall_ret() that matches
TDX_HCALL_HAS_OUTPUT semantics.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/20230321003511.9469-1-kirill.shutemov%40linux.intel.com
- Prevent unexpected #VE's from:
- Hosts removing perfectly good guest mappings (SEPT_VE_DISABLE
- Excessive #VE notifications (NOTIFY_ENABLES) which are
delivered via a #VE.
-----BEGIN PGP SIGNATURE-----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=UpyL
-----END PGP SIGNATURE-----
Merge tag 'x86_tdx_for_6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull Intel Trust Domain Extensions (TDX) updates from Dave Hansen:
"Other than a minor fixup, the content here is to ensure that TDX
guests never see virtualization exceptions (#VE's) that might be
induced by the untrusted VMM.
This is a highly desirable property. Without it, #VE exception
handling would fall somewhere between NMIs, machine checks and total
insanity. With it, #VE handling remains pretty mundane.
Summary:
- Fixup comment typo
- Prevent unexpected #VE's from:
- Hosts removing perfectly good guest mappings (SEPT_VE_DISABLE)
- Excessive #VE notifications (NOTIFY_ENABLES) which are delivered
via a #VE"
* tag 'x86_tdx_for_6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tdx: Do not corrupt frame-pointer in __tdx_hypercall()
x86/tdx: Disable NOTIFY_ENABLES
x86/tdx: Relax SEPT_VE_DISABLE check for debug TD
x86/tdx: Use ReportFatalError to report missing SEPT_VE_DISABLE
x86/tdx: Expand __tdx_hypercall() to handle more arguments
x86/tdx: Refactor __tdx_hypercall() to allow pass down more arguments
x86/tdx: Add more registers to struct tdx_hypercall_args
x86/tdx: Fix typo in comment in __tdx_hypercall()
struct tdx_hypercall_args is used to pass down hypercall arguments to
__tdx_hypercall() assembly routine.
Currently __tdx_hypercall() handles up to 6 arguments. In preparation to
changes in __tdx_hypercall(), expand the structure to 6 more registers
and generate asm offsets for them.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/20230126221159.8635-3-kirill.shutemov%40linux.intel.com
Now that arch_cpu_idle() is expected to return with IRQs disabled,
avoid the useless STI/CLI dance.
Per the specs this is supposed to work, but nobody has yet relied up
this behaviour so broken implementations are possible.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20230112195540.682137572@infradead.org
Port I/O instructions trigger #VE in the TDX environment. In response to
the exception, kernel emulates these instructions using hypercalls.
But during early boot, on the decompression stage, it is cumbersome to
deal with #VE. It is cleaner to go to hypercalls directly, bypassing #VE
handling.
Hook up TDX-specific port I/O helpers if booting in TDX environment.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20220405232939.73860-17-kirill.shutemov@linux.intel.com
The early decompression code does port I/O for its console output. But,
handling the decompression-time port I/O demands a different approach
from normal runtime because the IDT required to support #VE based port
I/O emulation is not yet set up. Paravirtualizing I/O calls during
the decompression step is acceptable because the decompression code
doesn't have a lot of call sites to IO instruction.
To support port I/O in decompression code, TDX must be detected before
the decompression code might do port I/O. Detect whether the kernel runs
in a TDX guest.
Add an early_is_tdx_guest() interface to query the cached TDX guest
status in the decompression code.
TDX is detected with CPUID. Make cpuid_count() accessible outside
boot/cpuflags.c.
TDX detection in the main kernel is very similar. Move common bits
into <asm/shared/tdx.h>.
The actual port I/O paravirtualization will come later in the series.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20220405232939.73860-13-kirill.shutemov@linux.intel.com
