The Toshiba documentation talks about HSByteClk when referring to the
DSI HS byte clock, whereas the driver uses 'dsibclk' name. Also, in a
few places the driver calculates the byte clock from the DSI clock, even
if the byte clock is already available in a variable.
To align the driver with the documentation, change the 'dsibclk'
variable to 'hsbyteclk'. This also make it easier to visually separate
'dsibclk' and 'dsiclk' variables.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-9-31725f008a50@ideasonboard.com
Simplify the code by capturing the priv->dev value to dev variable, and
use it.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-8-31725f008a50@ideasonboard.com
The driver debug prints DSI related timings as raw register values in
hex. It is much more useful to see the "logical" value of the timing,
not the register value.
Change the prints to print the values separately, in case a single
register contains multiple values, and use %u to have it in a more human
consumable form.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-7-31725f008a50@ideasonboard.com
The TC358768 documentation uses HFP, HBP, etc. values to deal with the
video mode, while the driver currently uses the DRM display mode
(htotal, hsync_start, etc).
Change the driver to convert the DRM display mode to struct videomode,
which then allows us to use the same units the documentation uses. This
makes it much easier to work on the code when using the TC358768
documentation as a reference.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-6-31725f008a50@ideasonboard.com
As is quite common, some of TC358768's PLL register fields are to be
programmed with (value - 1). Specifically, the FBD and PRD, multiplier
and divider, are such fields.
However, what the driver currently does is that it considers that the
formula used for PLL rate calculation is:
RefClk * [(FBD + 1)/ (PRD + 1)] * [1 / (2^FRS)]
where FBD and PRD are values directly from the registers, while a more
sensible way to look at it is:
RefClk * FBD / PRD * (1 / (2^FRS))
and when the FBD and PRD values are written to the registers, they will
be subtracted by one.
Change the driver accordingly, as it simplifies the PLL code.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-5-31725f008a50@ideasonboard.com
The driver has a few places where it does:
if (thing_is_enabled_in_config)
update_thing_bit_in_hw()
This means that if the thing is _not_ enabled, the bit never gets
cleared. This affects the h/vsyncs and continuous DSI clock bits.
Fix the driver to always update the bit.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-4-31725f008a50@ideasonboard.com
As the TC358768 is a DPI to DSI bridge, the DSI side does not need to
define h/v sync polarities. This means that sometimes we have a mode
without defined sync polarities, which does not work on the DPI side.
Add a mode_fixup hook to default to positive sync polarities.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-3-31725f008a50@ideasonboard.com
smatch reports:
drivers/gpu/drm/bridge/tc358768.c:223 tc358768_update_bits() error: uninitialized symbol 'orig'.
Fix this by bailing out from tc358768_update_bits() if the
tc358768_read() produces an error.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-2-31725f008a50@ideasonboard.com
Analogix ANX78XX driver is missing definitions for anx7816.
It uses the same I2C register set as anx7818.
Signed-off-by: Alicja Michalska <ahplka19@gmail.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/ZPvagaXnQ/TlNEkJ@tora
The drm stack does not expect error valued pointers for EDID anywhere.
Fixes: e668565087 ("drm: bridge: it66121: Set DDC preamble only once before reading EDID")
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Phong LE <ple@baylibre.com>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Robert Foss <rfoss@kernel.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: <stable@vger.kernel.org> # v6.3+
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230914131159.2472513-1-jani.nikula@intel.com
Having conditional around the of_node pointers turns out to make driver
code use ugly #ifdef and #if blocks. So drop the conditionals.
Suggested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230831080938.47454-4-biju.das.jz@bp.renesas.com
The driver has an ID table, but it uses the wrong API for retrieving match
data and that will lead to a crash, if it is instantiated by user space or
using ID. From this, there is no user for the ID table and let's drop it
from the driver as it saves some memory.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230831080938.47454-2-biju.das.jz@bp.renesas.com
The driver does not call drm_bridge_attach(), which causes the next
bridge to not be added to the bridge chain. This causes the pipeline
init to fail when DRM_BRIDGE_ATTACH_NO_CONNECTOR is used.
Add the call to drm_bridge_attach().
Fixes: 30e2ae943c ("drm/bridge: Introduce LT8912B DSI to HDMI bridge")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804-lt8912b-v1-4-c542692c6a2f@ideasonboard.com
lt8912b only calls drm_bridge_hpd_enable() if it creates a connector and
the next bridge has DRM_BRIDGE_OP_HPD set. However, when calling
drm_bridge_hpd_disable() it misses checking if a connector was created,
calling drm_bridge_hpd_disable() even if HPD was never enabled. I don't
see any issues caused by this wrong call, though.
Add the check to avoid wrongly calling drm_bridge_hpd_disable().
Fixes: 3b0a01a6a5 ("drm/bridge: lt8912b: Add hot plug detection")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804-lt8912b-v1-3-c542692c6a2f@ideasonboard.com
The driver calls lt8912_bridge_detach() from its lt8912_remove()
function. As the DRM core detaches bridges automatically, this leads to
calling lt8912_bridge_detach() twice. The code probably has tried to
manage the double-call with the 'is_attached' variable, but the driver
never sets the variable to false, so its of no help.
Fix the issue by dropping the call to lt8912_bridge_detach() from
lt8912_remove(), as the DRM core will handle the detach call for us,
and also drop the useless is_attached field.
Fixes: 30e2ae943c ("drm/bridge: Introduce LT8912B DSI to HDMI bridge")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804-lt8912b-v1-1-c542692c6a2f@ideasonboard.com
Fix the NULL pointer dereference when no monitor is connected, and the
sound card is opened from userspace.
Instead return an empty buffer (of zeroes) as the EDID information to
the sound framework if there is no connector attached.
Fixes: e0fd83dbe9 ("drm: bridge: it66121: Add audio support")
Reported-by: Nishanth Menon <nm@ti.com>
Closes: https://lore.kernel.org/all/20230825105849.crhon42qndxqif4i@gondola/
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901-it66121_edid-v2-1-aa59605336b9@ti.com
Simplify probe() by replacing of_device_get_match_data() and ID lookup
for retrieving match data by i2c_get_match_data().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230818191817.340360-3-biju.das.jz@bp.renesas.com
The driver has OF match table, still it uses ID lookup table for
retrieving match data. Currently the driver is working on the
assumption that a I2C device registered via OF will always match a
legacy I2C device ID. The correct approach is to have an OF device ID
table using of_device_match_data() if the devices are registered via OF.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230818191817.340360-2-biju.das.jz@bp.renesas.com
core:
- fix gfp flags in drmm_kmalloc
gpuva:
- add new generic GPU VA manager (for nouveau initially)
syncobj:
- add new DRM_IOCTL_SYNCOBJ_EVENTFD ioctl
dma-buf:
- acquire resv lock for mmap() in exporters
- support dma-buf self import automatically
- docs fixes
backlight:
- fix fbdev interactions
atomic:
- improve logging
prime:
- remove struct gem_prim_mmap plus driver updates
gem:
- drm_exec: add locking over multiple GEM objects
- fix lockdep checking
fbdev:
- make fbdev userspace interfaces optional
- use linux device instead of fbdev device
- use deferred i/o helper macros in various drivers
- Make FB core selectable without drivers
- Remove obsolete flags FBINFO_DEFAULT and FBINFO_FLAG_DEFAULT
- Add helper macros and Kconfig tokens for DMA-allocated framebuffer
ttm:
- support init_on_free
- swapout fixes
panel:
- panel-edp: Support AUO B116XAB01.4
- Support Visionox R66451 plus DT bindings
- ld9040: Backlight support, magic improved,
Kconfig fix
- Convert to of_device_get_match_data()
- Fix Kconfig dependencies
- simple: Set bpc value to fix warning; Set connector type for AUO T215HVN01;
Support Innolux G156HCE-L01 plus DT bindings
- ili9881: Support TDO TL050HDV35 LCD panel plus DT bindings
- startek: Support KD070FHFID015 MIPI-DSI panel plus DT bindings
- sitronix-st7789v: Support Inanbo T28CP45TN89 plus DT bindings;
Support EDT ET028013DMA plus DT bindings; Various cleanups
- edp: Add timings for N140HCA-EAC
- Allow panels and touchscreens to power sequence together
- Fix Innolux G156HCE-L01 LVDS clock
bridge:
- debugfs for chains support
- dw-hdmi: Improve support for YUV420 bus format
CEC suspend/resume, update EDID on HDMI detect
- dw-mipi-dsi: Fix enable/disable of DSI controller
- lt9611uxc: Use MODULE_FIRMWARE()
- ps8640: Remove broken EDID code
- samsung-dsim: Fix command transfer
- tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
- adv7511: Fix low refresh rate
- anx7625: Switch to macros instead of hardcoded values
locking fixes
- tc358767: fix hardware delays
- sitronix-st7789v: Support panel orientation; Support rotation
property; Add support for Jasonic
JT240MHQS-HWT-EK-E3 plus DT bindings
amdgpu:
- SDMA 6.1.0 support
- HDP 6.1 support
- SMUIO 14.0 support
- PSP 14.0 support
- IH 6.1 support
- Lots of checkpatch cleanups
- GFX 9.4.3 updates
- Add USB PD and IFWI flashing documentation
- GPUVM updates
- RAS fixes
- DRR fixes
- FAMS fixes
- Virtual display fixes
- Soft IH fixes
- SMU13 fixes
- Rework PSP firmware loading for other IPs
- Kernel doc fixes
- DCN 3.0.1 fixes
- LTTPR fixes
- DP MST fixes
- DCN 3.1.6 fixes
- SMU 13.x fixes
- PSP 13.x fixes
- SubVP fixes
- GC 9.4.3 fixes
- Display bandwidth calculation fixes
- VCN4 secure submission fixes
- Allow building DC on RISC-V
- Add visible FB info to bo_print_info
- HBR3 fixes
- GFX9 MCBP fix
- GMC10 vmhub index fix
- GMC11 vmhub index fix
- Create a new doorbell manager
- SR-IOV fixes
- initial freesync panel replay support
- revert zpos properly until igt regression is fixeed
- use TTM to manage doorbell BAR
- Expose both current and average power via hwmon if supported
amdkfd:
- Cleanup CRIU dma-buf handling
- Use KIQ to unmap HIQ
- GFX 9.4.3 debugger updates
- GFX 9.4.2 debugger fixes
- Enable cooperative groups fof gfx11
- SVM fixes
- Convert older APUs to use dGPU path like newer APUs
- Drop IOMMUv2 path as it is no longer used
- TBA fix for aldebaran
i915:
- ICL+ DSI modeset sequence
- HDCP improvements
- MTL display fixes and cleanups
- HSW/BDW PSR1 restored
- Init DDI ports in VBT order
- General display refactors
- Start using plane scale factor for relative data rate
- Use shmem for dpt objects
- Expose RPS thresholds in sysfs
- Apply GuC SLPC min frequency softlimit correctly
- Extend Wa_14015795083 to TGL, RKL, DG1 and ADL
- Fix a VMA UAF for multi-gt platform
- Do not use stolen on MTL due to HW bug
- Check HuC and GuC version compatibility on MTL
- avoid infinite GPU waits due to premature release
of request memory
- Fixes and updates for GSC memory allocation
- Display SDVO fixes
- Take stolen handling out of FBC code
- Make i915_coherent_map_type GT-centric
- Simplify shmem_create_from_object map_type
msm:
- SM6125 MDSS support
- DPU: SM6125 DPU support
- DSI: runtime PM support, burst mode support
- DSI PHY: SM6125 support in 14nm DSI PHY driver
- GPU: prepare for a7xx
- fix a690 firmware
- disable relocs on a6xx and newer
radeon:
- Lots of checkpatch cleanups
ast:
- improve device-model detection
- Represent BMV as virtual connector
- Report DP connection status
nouveau:
- add new exec/bind interface to support Vulkan
- document some getparam ioctls
- improve VRAM detection
- various fixes/cleanups
- workraound DPCD issues
ivpu:
- MMU updates
- debugfs support
- Support vpu4
virtio:
- add sync object support
atmel-hlcdc:
- Support inverted pixclock polarity
etnaviv:
- runtime PM cleanups
- hang handling fixes
exynos:
- use fbdev DMA helpers
- fix possible NULL ptr dereference
komeda:
- always attach encoder
omapdrm:
- use fbdev DMA helpers
ingenic:
- kconfig regmap fixes
loongson:
- support display controller
mediatek:
- Small mtk-dpi cleanups
- DisplayPort: support eDP and aux-bus
- Fix coverity issues
- Fix potential memory leak if vmap() fail
mgag200:
- minor fixes
mxsfb:
- support disabling overlay planes
panfrost:
- fix sync in IRQ handling
ssd130x:
- Support per-controller default resolution plus DT bindings
- Reduce memory-allocation overhead
- Improve intermediate buffer size computation
- Fix allocation of temporary buffers
- Fix pitch computation
- Fix shadow plane allocation
tegra:
- use fbdev DMA helpers
- Convert to devm_platform_ioremap_resource()
- support bridge/connector
- enable PM
tidss:
- Support TI AM625 plus DT bindings
- Implement new connector model plus driver updates
vkms:
- improve write back support
- docs fixes
- support gamma LUT
zynqmp-dpsub:
- misc fixes
-----BEGIN PGP SIGNATURE-----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=CwV9
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2023-08-30' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"The drm core grew a new generic gpu virtual address manager, and new
execution locking helpers. These are used by nouveau now to provide
uAPI support for the userspace Vulkan driver. AMD had a bunch of new
IP core support, loads of refactoring around fbdev, but mostly just
the usual amount of stuff across the board.
core:
- fix gfp flags in drmm_kmalloc
gpuva:
- add new generic GPU VA manager (for nouveau initially)
syncobj:
- add new DRM_IOCTL_SYNCOBJ_EVENTFD ioctl
dma-buf:
- acquire resv lock for mmap() in exporters
- support dma-buf self import automatically
- docs fixes
backlight:
- fix fbdev interactions
atomic:
- improve logging
prime:
- remove struct gem_prim_mmap plus driver updates
gem:
- drm_exec: add locking over multiple GEM objects
- fix lockdep checking
fbdev:
- make fbdev userspace interfaces optional
- use linux device instead of fbdev device
- use deferred i/o helper macros in various drivers
- Make FB core selectable without drivers
- Remove obsolete flags FBINFO_DEFAULT and FBINFO_FLAG_DEFAULT
- Add helper macros and Kconfig tokens for DMA-allocated framebuffer
ttm:
- support init_on_free
- swapout fixes
panel:
- panel-edp: Support AUO B116XAB01.4
- Support Visionox R66451 plus DT bindings
- ld9040:
- Backlight support
- magic improved
- Kconfig fix
- Convert to of_device_get_match_data()
- Fix Kconfig dependencies
- simple:
- Set bpc value to fix warning
- Set connector type for AUO T215HVN01
- Support Innolux G156HCE-L01 plus DT bindings
- ili9881: Support TDO TL050HDV35 LCD panel plus DT bindings
- startek: Support KD070FHFID015 MIPI-DSI panel plus DT bindings
- sitronix-st7789v:
- Support Inanbo T28CP45TN89 plus DT bindings
- Support EDT ET028013DMA plus DT bindings
- Various cleanups
- edp: Add timings for N140HCA-EAC
- Allow panels and touchscreens to power sequence together
- Fix Innolux G156HCE-L01 LVDS clock
bridge:
- debugfs for chains support
- dw-hdmi:
- Improve support for YUV420 bus format
- CEC suspend/resume
- update EDID on HDMI detect
- dw-mipi-dsi: Fix enable/disable of DSI controller
- lt9611uxc: Use MODULE_FIRMWARE()
- ps8640: Remove broken EDID code
- samsung-dsim: Fix command transfer
- tc358764:
- Handle HS/VS polarity
- Use BIT() macro
- Various cleanups
- adv7511: Fix low refresh rate
- anx7625:
- Switch to macros instead of hardcoded values
- locking fixes
- tc358767: fix hardware delays
- sitronix-st7789v:
- Support panel orientation
- Support rotation property
- Add support for Jasonic JT240MHQS-HWT-EK-E3 plus DT bindings
amdgpu:
- SDMA 6.1.0 support
- HDP 6.1 support
- SMUIO 14.0 support
- PSP 14.0 support
- IH 6.1 support
- Lots of checkpatch cleanups
- GFX 9.4.3 updates
- Add USB PD and IFWI flashing documentation
- GPUVM updates
- RAS fixes
- DRR fixes
- FAMS fixes
- Virtual display fixes
- Soft IH fixes
- SMU13 fixes
- Rework PSP firmware loading for other IPs
- Kernel doc fixes
- DCN 3.0.1 fixes
- LTTPR fixes
- DP MST fixes
- DCN 3.1.6 fixes
- SMU 13.x fixes
- PSP 13.x fixes
- SubVP fixes
- GC 9.4.3 fixes
- Display bandwidth calculation fixes
- VCN4 secure submission fixes
- Allow building DC on RISC-V
- Add visible FB info to bo_print_info
- HBR3 fixes
- GFX9 MCBP fix
- GMC10 vmhub index fix
- GMC11 vmhub index fix
- Create a new doorbell manager
- SR-IOV fixes
- initial freesync panel replay support
- revert zpos properly until igt regression is fixeed
- use TTM to manage doorbell BAR
- Expose both current and average power via hwmon if supported
amdkfd:
- Cleanup CRIU dma-buf handling
- Use KIQ to unmap HIQ
- GFX 9.4.3 debugger updates
- GFX 9.4.2 debugger fixes
- Enable cooperative groups fof gfx11
- SVM fixes
- Convert older APUs to use dGPU path like newer APUs
- Drop IOMMUv2 path as it is no longer used
- TBA fix for aldebaran
i915:
- ICL+ DSI modeset sequence
- HDCP improvements
- MTL display fixes and cleanups
- HSW/BDW PSR1 restored
- Init DDI ports in VBT order
- General display refactors
- Start using plane scale factor for relative data rate
- Use shmem for dpt objects
- Expose RPS thresholds in sysfs
- Apply GuC SLPC min frequency softlimit correctly
- Extend Wa_14015795083 to TGL, RKL, DG1 and ADL
- Fix a VMA UAF for multi-gt platform
- Do not use stolen on MTL due to HW bug
- Check HuC and GuC version compatibility on MTL
- avoid infinite GPU waits due to premature release of request memory
- Fixes and updates for GSC memory allocation
- Display SDVO fixes
- Take stolen handling out of FBC code
- Make i915_coherent_map_type GT-centric
- Simplify shmem_create_from_object map_type
msm:
- SM6125 MDSS support
- DPU: SM6125 DPU support
- DSI: runtime PM support, burst mode support
- DSI PHY: SM6125 support in 14nm DSI PHY driver
- GPU: prepare for a7xx
- fix a690 firmware
- disable relocs on a6xx and newer
radeon:
- Lots of checkpatch cleanups
ast:
- improve device-model detection
- Represent BMV as virtual connector
- Report DP connection status
nouveau:
- add new exec/bind interface to support Vulkan
- document some getparam ioctls
- improve VRAM detection
- various fixes/cleanups
- workraound DPCD issues
ivpu:
- MMU updates
- debugfs support
- Support vpu4
virtio:
- add sync object support
atmel-hlcdc:
- Support inverted pixclock polarity
etnaviv:
- runtime PM cleanups
- hang handling fixes
exynos:
- use fbdev DMA helpers
- fix possible NULL ptr dereference
komeda:
- always attach encoder
omapdrm:
- use fbdev DMA helpers
ingenic:
- kconfig regmap fixes
loongson:
- support display controller
mediatek:
- Small mtk-dpi cleanups
- DisplayPort: support eDP and aux-bus
- Fix coverity issues
- Fix potential memory leak if vmap() fail
mgag200:
- minor fixes
mxsfb:
- support disabling overlay planes
panfrost:
- fix sync in IRQ handling
ssd130x:
- Support per-controller default resolution plus DT bindings
- Reduce memory-allocation overhead
- Improve intermediate buffer size computation
- Fix allocation of temporary buffers
- Fix pitch computation
- Fix shadow plane allocation
tegra:
- use fbdev DMA helpers
- Convert to devm_platform_ioremap_resource()
- support bridge/connector
- enable PM
tidss:
- Support TI AM625 plus DT bindings
- Implement new connector model plus driver updates
vkms:
- improve write back support
- docs fixes
- support gamma LUT
zynqmp-dpsub:
- misc fixes"
* tag 'drm-next-2023-08-30' of git://anongit.freedesktop.org/drm/drm: (1327 commits)
drm/gpuva_mgr: remove unused prev pointer in __drm_gpuva_sm_map()
drm/tests/drm_kunit_helpers: Place correct function name in the comment header
drm/nouveau: uapi: don't pass NO_PREFETCH flag implicitly
drm/nouveau: uvmm: fix unset region pointer on remap
drm/nouveau: sched: avoid job races between entities
drm/i915: Fix HPD polling, reenabling the output poll work as needed
drm: Add an HPD poll helper to reschedule the poll work
drm/i915: Fix TLB-Invalidation seqno store
drm/ttm/tests: Fix type conversion in ttm_pool_test
drm/msm/a6xx: Bail out early if setting GPU OOB fails
drm/msm/a6xx: Move LLC accessors to the common header
drm/msm/a6xx: Introduce a6xx_llc_read
drm/ttm/tests: Require MMU when testing
drm/panel: simple: Fix Innolux G156HCE-L01 LVDS clock
Revert "Revert "drm/amdgpu/display: change pipe policy for DCN 2.0""
drm/amdgpu: Add memory vendor information
drm/amd: flush any delayed gfxoff on suspend entry
drm/amdgpu: skip fence GFX interrupts disable/enable for S0ix
drm/amdgpu: Remove gfxoff check in GFX v9.4.3
drm/amd/pm: Update pci link speed for smu v13.0.6
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmTiDvweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG7doH/2Poj73npPKPVfT3
RF8AsgvAj2pLby67rdvwTdFX+exS63SsuwtGGRfAHfGabiwmNN+oT2dLb0aY15bp
nskHnFpcqQ/pfZ2i2rUCenzBX8S9QULvPidLKRaf1FcSdOzqd97Bw5oDPMtzqy/R
Pm+Dzs//7fYvtm69nt6hKW4d6wXxNcg7Fk/QgoJ5Ax9vGvDuZmWXH0ZgBf/5kH04
TTPQNtVX57lf+FHugkhFEn4JbYXvN168b+LuX2PHwOeG/8AIS69Hc0vgvhHNAycT
mmpUI1gWA2jfrJ2RCyyezF/6wy9Ocsp+CbPjfwjuRUxOk0XIm1+cp9Mlz/cRbMsZ
f0tOTpk=
=xrJp
-----END PGP SIGNATURE-----
BackMerge tag 'v6.5-rc7' into drm-next
Linux 6.5-rc7
This is needed for the CI stuff and the msm pull has fixes in it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
In case the downstream bridge or panel uses DSI transfers before the
DSI host was actually initialized through samsung_dsim_atomic_enable()
which clears the stop state (LP11) mode, all transfers will fail.
This happens with downstream bridges that are controlled by DSI
commands such as the tc358762.
As documented in [1] DSI hosts are expected to allow transfers
outside the normal bridge enable/disable flow.
To fix this make sure that stop state is cleared in
samsung_dsim_host_transfer() which restores the previous
behavior.
We also factor out the common code to enable/disable stop state
to samsung_dsim_set_stop_state().
[1] https://docs.kernel.org/gpu/drm-kms-helpers.html#mipi-dsi-bridge-operation
Fixes: 0c14d31306 ("drm: bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec")
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230724151640.555490-1-frieder@fris.de
Add the device link when panel bridge is attached and delete the link
when panel bridge is detached. The drm device is the consumer while
the panel device is the supplier. This makes sure that the drm device
suspends eariler and resumes later than the panel device, hence resolves
problems where the order is reversed, like the problematic case mentioned
in the below link.
Link: https://lore.kernel.org/lkml/CAPDyKFr0XjrU_udKoUKQ_q8RWaUkyqL+8fV-7s1CTMqi7u3-Rg@mail.gmail.com/T/
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230807061115.3244501-1-victor.liu@nxp.com
atomic_get_input_bus_fmts is only implemented for LVDS decoders, resulting
that LVDS encoders only support bus format MEDIA_BUS_FMT_FIXED. This
results in warnings like:
mxsfb 21c8000.lcdif: Bridge does not provide bus format, assuming
MEDIA_BUS_FMT_RGB888_1X24.
Please fix bridge driver by handling atomic_get_input_bus_fmts.
Fix this by reusing lvds_codec_atomic_get_input_bus_fmts currently used
for LVDS decoders. Use RGB888_1X24 for LVDS encoders. This also allows
removing the dedicated struct drm_bridge_funcs for decoders.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230810063229.597533-1-alexander.stein@ew.tq-group.com
Samsung DSIM used in older Exynos SoCs (like Exynos 4210, 4x12, 3250)
doesn't report empty level of packer header FIFO. In case of those SoCs,
use the old way of waiting for empty command tranfsfer FIFO, removed
recently by commit 14806c6415 ("drm: bridge: samsung-dsim: Drain command transfer FIFO before transfer").
Fixes: 14806c6415 ("drm: bridge: samsung-dsim: Drain command transfer FIFO before transfer")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230809145641.3213210-1-m.szyprowski@samsung.com
Three DRM bridge drivers select GENERIC_PHY_MIPI_DPHY when GENERIC_PHY
might not be set. This causes Kconfig warnings and a build error.
WARNING: unmet direct dependencies detected for GENERIC_PHY_MIPI_DPHY
Depends on [n]: GENERIC_PHY [=n]
Selected by [y]:
- DRM_NWL_MIPI_DSI [=y] && DRM_BRIDGE [=y] && DRM [=y] && COMMON_CLK [=y] && OF [=y] && HAS_IOMEM [=y]
- DRM_SAMSUNG_DSIM [=y] && DRM [=y] && DRM_BRIDGE [=y] && COMMON_CLK [=y] && OF [=y] && HAS_IOMEM [=y]
(drm/bridge/cadence/Kconfig was found by inspection.)
aarch64-linux-ld: drivers/gpu/drm/bridge/samsung-dsim.o: in function `samsung_dsim_set_phy_ctrl':
drivers/gpu/drm/bridge/samsung-dsim.c:731: undefined reference to `phy_mipi_dphy_get_default_config_for_hsclk'
Prevent these warnings and build error by also selecting GENERIC_PHY
whenever selecting GENERIC_PHY_MIPI_DPHY.
Fixes: fced5a364d ("drm/bridge: cdns: Convert to phy framework")
Fixes: 44cfc62334 ("drm/bridge: Add NWL MIPI DSI host controller support")
Fixes: 171b3b1e0f ("drm: bridge: samsung-dsim: Select GENERIC_PHY_MIPI_DPHY")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Aleksandr Nogikh <nogikh@google.com>
Link: lore.kernel.org/r/20230803144227.2187749-1-nogikh@google.com
Cc: Adam Ford <aford173@gmail.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Guido Günther <agx@sigxcpu.org>
Cc: Robert Chiras <robert.chiras@nxp.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Robert Foss <rfoss@kernel.org>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Adam Ford <aford173@gmail.com>
Tested-by: Aleksandr Nogikh <nogikh@google.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804030140.21395-1-rdunlap@infradead.org
The ULPS EXIT is initialized to 0xaf in downstream BSP as well as older
revisions of this patchset, in newer revisions of the DSIM patchset it
was left out and set to 0. Fix it.
Fixes: 4d562c70c4 ("drm: bridge: samsung-dsim: Add i.MX8M Mini/Nano support")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230709134827.449185-1-marex@denx.de
The ELD (EDID-Like Data) is not updated when the HDMI cable
is plugged into different HDMI monitors.
This is because the EDID is not updated in the HDMI HPD function.
As a result, the ELD data remains unchanged and may not reflect
the capabilities of the newly connected HDMI sink device.
To address this issue, the handle_plugged_change function should move to
the bridge_atomic_enable and bridge_atomic_disable functions.
Make sure the EDID is properly updated before updating ELD.
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804061145.2824843-1-Sandor.yu@nxp.com
This reverts commit 8ddce13ae6 ("drm/bridge: lt9611: Do not generate
HFP/HBP/HSA and EOT packet") to fix display regression on the Dragonboard
845c (SDM845) devboard.
There's a mismatch on the real action of the following flags:
- MIPI_DSI_MODE_VIDEO_NO_HSA
- MIPI_DSI_MODE_VIDEO_NO_HFP
- MIPI_DSI_MODE_VIDEO_NO_HBP
which leads to a non-working display on qcom platforms.
Cc: Marek Vasut <marex@denx.de>
Cc: Robert Foss <rfoss@kernel.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Fixes: 8ddce13ae6 ("drm/bridge: lt9611: Do not generate HFP/HBP/HSA and EOT packet")
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Closes: https://lore.kernel.org/r/CAMi1Hd0TD=2z_=bcDrht3H_wiLvAFcv8Z-U_r_KUOoeMc6UMjw@mail.gmail.com/
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #fix db845c
[narmstrong: fixed commit message format]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230802-revert-do-not-generate-hfp-hbp-hsa-eot-packet-v1-1-f8a20084e15a@linaro.org
On system resume, the driver might call it6505_poweron directly if the
runtime PM hasn't been enabled. In such case, pm_runtime_get_if_in_use
will always return 0 because dev->power.runtime_status stays at
RPM_SUSPENDED, and the IRQ will never be handled.
Use it6505->powered from the driver struct fixes this because it always
gets updated when it6505_poweron is called.
Fixes: 5eb9a43140 ("drm/bridge: it6505: Guard bridge power in IRQ handler")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230727100131.2338127-1-treapking@chromium.org
CEC interrupt status/mask and logical address registers
will be reset when device enter suspend.
It will cause cec fail to work after device resume.
Add CEC suspend/resume functions, reinitialize logical address registers
and restore interrupt status/mask registers after resume.
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230721124415.1513223-1-Sandor.yu@nxp.com
When building with W=1, the following warning occurs.
drivers/gpu/drm/bridge/analogix/analogix-anx78xx.c:48:17: warning: ‘anx781x_i2c_addresses’ defined but not used [-Wunused-const-variable=] static const u8 anx781x_i2c_addresses[] = {
^~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/bridge/analogix/analogix-anx78xx.c:40:17: warning: ‘anx7808_i2c_addresses’ defined but not used [-Wunused-const-variable=] static const u8 anx7808_i2c_addresses[] = {
When CONFIG_IO is disabled, above two variables are not used,
since the place where it is used is inclueded in the macro
CONFIG_OF.
Even for drivers that do not depend on CONFIG_OF, it's almost
always better to leave out the of_match_ptr(), since the only
thing it can possibly do is to save a few bytes of .text if a
driver can be used both with and without it. Hence we remove
all of_match_ptr() used in other places.
Fixes: 0647e7dd3f ("drm/bridge: Add Analogix anx78xx support")
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230731021345.219588-1-wangzhu9@huawei.com
These two drivers embed a i2c_client in their private driver data, but
only strict device is actually needed. Replace the i2c_client reference
with a struct device one.
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230718110407.1005200-1-wenst@chromium.org
Replace the spaces with tab characters in the Kconfig file.
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230712065054.2377278-1-wenst@chromium.org
The device lock is used to serialize the low level power sequencing
operations. Since drm_helper_hpd_irq_event() could end up calling
.atomic_enable, which also calls power sequencing functions through
runtime PM, this results in a real deadlock. This was observed on an
MT8192-based Chromebook's external display (with appropriate patches [1]
and DT changes applied).
Move the drm_helper_hpd_irq_event() call outside of the lock range. The
lock only needs to be held so that the device status can be read back.
This is the bare minimum change to avoid the deadlock. The lock could
be dropped completely and have pm_runtime_get_if_in_use() increase the
reference count, but this is not the same as pm_runtime_suspended().
Dropping the lock completely also causes the internal display of the
same device to not function correctly if the internal bridge's
interrupt line is added in the device tree. Both the internal and
external display of said device each use one anx7625 bridge.
[1] https://lore.kernel.org/dri-devel/20230112042104.4107253-1-treapking@chromium.org/
Fixes: 60487584a7 ("drm/bridge: anx7625: refactor power control to use runtime PM framework")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230710085922.1871465-1-wenst@chromium.org
The documentation is not clear about how this delay works.
Empirical tests have shown that with a VSDELAY of 0, the first
scanline is not properly formatted in the output stream when
DSI->DP mode is used. The calculation spreadsheets from Toshiba
seem to always make this value equal to the HFP + 10 for DSI->DP
use-case. For DSI->DPI this value should be > 2 and for DPI->DP
it seems to always be 0x64.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Marek Vasut <marex@denx.de> # TC9595
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230721165328.3968759-2-l.stach@pengutronix.de
The PLL often fails to lock with this delay. The new value was
determined by trial and error increasing the delay bit by bit
until the error did not occurr anymore even after several tries.
Then double that value was taken as the minimum delay to be safe.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de> # TC9595
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230721165328.3968759-1-l.stach@pengutronix.de
For ADV7533 and ADV7535 low refresh rate is selected using
bits [3:2] of 0x4a main register.
So depending on ADV model write 0xfb or 0x4a register.
Fixes: 2437e7cd88 ("drm/bridge: adv7533: Initial support for ADV7533")
Reviewed-by: Robert Foss <rfoss@kernel.org>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Bogdan Togorean <bogdan.togorean@analog.com>
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230719060143.63649-1-alex@shruggie.ro
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714174545.4056287-1-robh@kernel.org
The DRM DP code has macros for the DP HDCP capabilities. Use them in the
anx7625 driver instead of raw numbers.
Fixes: cd1637c7e4 ("drm/bridge: anx7625: add HDCP support")
Suggested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230710091203.1874317-1-wenst@chromium.org
The DRM DP code has macros for the DP power sequencing commands. Use
them in the anx7625 driver instead of raw numbers.
Fixes: 548b512e14 ("drm/bridge: anx7625: send DPCD command to downstream")
Fixes: 27f26359de ("drm/bridge: anx7625: Set downstream sink into normal status")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230710090929.1873646-1-wenst@chromium.org
UAPI Changes:
* fbdev:
* Make fbdev userspace interfaces optional; only leaves the
framebuffer console active
* prime:
* Support dma-buf self-import for all drivers automatically: improves
support for many userspace compositors
Cross-subsystem Changes:
* backlight:
* Fix interaction with fbdev in several drivers
* base: Convert struct platform.remove to return void; part of a larger,
tree-wide effort
* dma-buf: Acquire reservation lock for mmap() in exporters; part
of an on-going effort to simplify locking around dma-bufs
* fbdev:
* Use Linux device instead of fbdev device in many places
* Use deferred-I/O helper macros in various drivers
* i2c: Convert struct i2c from .probe_new to .probe; part of a larger,
tree-wide effort
* video:
* Avoid including <linux/screen_info.h>
Core Changes:
* atomic:
* Improve logging
* prime:
* Remove struct drm_driver.gem_prime_mmap plus driver updates: all
drivers now implement this callback with drm_gem_prime_mmap()
* gem:
* Support execution contexts: provides locking over multiple GEM
objects
* ttm:
* Support init_on_free
* Swapout fixes
Driver Changes:
* accel:
* ivpu: MMU updates; Support debugfs
* ast:
* Improve device-model detection
* Cleanups
* bridge:
* dw-hdmi: Improve support for YUV420 bus format
* dw-mipi-dsi: Fix enable/disable of DSI controller
* lt9611uxc: Use MODULE_FIRMWARE()
* ps8640: Remove broken EDID code
* samsung-dsim: Fix command transfer
* tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
* Cleanups
* ingenic:
* Kconfig REGMAP fixes
* loongson:
* Support display controller
* mgag200:
* Minor fixes
* mxsfb:
* Support disabling overlay planes
* nouveau:
* Improve VRAM detection
* Various fixes and cleanups
* panel:
* panel-edp: Support AUO B116XAB01.4
* Support Visionox R66451 plus DT bindings
* Cleanups
* ssd130x:
* Support per-controller default resolution plus DT bindings
* Reduce memory-allocation overhead
* Cleanups
* tidss:
* Support TI AM625 plus DT bindings
* Implement new connector model plus driver updates
* vkms
* Improve write-back support
* Documentation fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmSvvRAACgkQaA3BHVML
eiNpGQgAs8jq1XjN9t8jZsdgXnoCbkZyVUI2NO0HwoVwpRCLgbXp5AX5qq2oRciE
TBhe4Fceh/ZsYqHTZQahnguxgRKM5JgXwbI4Z0iiOVcqasNbycaKAqipxJJ7kdo1
qPhGCbgQFVX7oIq2xjfXehh6O0SYX+R9r88X8dMJxMYv/pcLwOHG74kS040WOcQq
uATgcnobOf/D8ZmlqvfKGAeTUoFo/RSR2Uhlauka58qgeUbicrTELZT2barY9d+k
as6U5vv4wx2zMklTkjrlkMpAT1ZpbB9d3jGHwL27VEnjlfd3wV2bdH7Dzn9qZRf/
gn0ALg/b3u5yBWk/k7YBvijXyNcH6Q==
=bBuG
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2023-07-13' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.6:
UAPI Changes:
* fbdev:
* Make fbdev userspace interfaces optional; only leaves the
framebuffer console active
* prime:
* Support dma-buf self-import for all drivers automatically: improves
support for many userspace compositors
Cross-subsystem Changes:
* backlight:
* Fix interaction with fbdev in several drivers
* base: Convert struct platform.remove to return void; part of a larger,
tree-wide effort
* dma-buf: Acquire reservation lock for mmap() in exporters; part
of an on-going effort to simplify locking around dma-bufs
* fbdev:
* Use Linux device instead of fbdev device in many places
* Use deferred-I/O helper macros in various drivers
* i2c: Convert struct i2c from .probe_new to .probe; part of a larger,
tree-wide effort
* video:
* Avoid including <linux/screen_info.h>
Core Changes:
* atomic:
* Improve logging
* prime:
* Remove struct drm_driver.gem_prime_mmap plus driver updates: all
drivers now implement this callback with drm_gem_prime_mmap()
* gem:
* Support execution contexts: provides locking over multiple GEM
objects
* ttm:
* Support init_on_free
* Swapout fixes
Driver Changes:
* accel:
* ivpu: MMU updates; Support debugfs
* ast:
* Improve device-model detection
* Cleanups
* bridge:
* dw-hdmi: Improve support for YUV420 bus format
* dw-mipi-dsi: Fix enable/disable of DSI controller
* lt9611uxc: Use MODULE_FIRMWARE()
* ps8640: Remove broken EDID code
* samsung-dsim: Fix command transfer
* tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
* Cleanups
* ingenic:
* Kconfig REGMAP fixes
* loongson:
* Support display controller
* mgag200:
* Minor fixes
* mxsfb:
* Support disabling overlay planes
* nouveau:
* Improve VRAM detection
* Various fixes and cleanups
* panel:
* panel-edp: Support AUO B116XAB01.4
* Support Visionox R66451 plus DT bindings
* Cleanups
* ssd130x:
* Support per-controller default resolution plus DT bindings
* Reduce memory-allocation overhead
* Cleanups
* tidss:
* Support TI AM625 plus DT bindings
* Implement new connector model plus driver updates
* vkms
* Improve write-back support
* Documentation fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230713090830.GA23281@linux-uq9g
When removing the tidss driver, there is a warning reported by
kernel about an unhandled interrupt for mhdp driver.
[ 43.238895] irq 31: nobody cared (try booting with the "irqpoll" option)
... [snipped backtrace]
[ 43.330735] handlers:
[ 43.333020] [<000000005367c4f9>] irq_default_primary_handler threaded [<000000007e02b601>]
cdns_mhdp_irq_handler [cdns_mhdp8546]
[ 43.344607] Disabling IRQ #31
This happens because as part of cdns_mhdp_bridge_hpd_disable, driver tries
to disable the interrupts. While disabling the SW_EVENT interrupts,
it accidentally enables the MBOX interrupts, which are not handled by
the driver.
Fix this with a read-modify-write to update only required bits.
Use the enable / disable function as required in other places.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606082142.23760-9-a-bhatia1@ti.com
input_bus_flags are specified in drm_bridge_timings (legacy) as well
as drm_bridge_state->input_bus_cfg.flags
The flags from the timings will be deprecated. Bridges are supposed
to validate and set the bridge state flags from atomic_check.
Implement atomic_check hook for the same.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606082142.23760-7-a-bhatia1@ti.com
With new connector model, sii902x will not create the connector, when
DRM_BRIDGE_ATTACH_NO_CONNECTOR is set and SoC driver will rely on format
negotiation to setup the encoder format.
Support format negotiations hooks in the drm_bridge_funcs.
Use helper functions for state management.
Input format is selected to MEDIA_BUS_FMT_RGB888_1X24 as default, as is
the case with older model.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606082142.23760-6-a-bhatia1@ti.com
input_bus_flags are specified in drm_bridge_timings (legacy) as well
as drm_bridge_state->input_bus_cfg.flags
The flags from the timings will be deprecated. Bridges are supposed
to validate and set the bridge state flags from atomic_check.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
[a-bhatia1: replace timings in cdns_mhdp_platform_info by input_bus_flags]
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606082142.23760-5-a-bhatia1@ti.com
With new connector model, mhdp bridge will not create the connector and
SoC driver will rely on format negotiation to setup the encoder format.
Support minimal format negotiations hooks in the drm_bridge_funcs.
Complete format negotiation can be added based on EDID data.
This patch adds the minimal required support to avoid failure
after moving to new connector model.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
[a-bhatia1: Drop the output_fmt check condition]
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606082142.23760-4-a-bhatia1@ti.com
