The current intel_bw_atomic_check do not check the possbility
of a sagv configuration change after the hw state readout.
Hence cannot update the sagv configuration until some other
relevant changes like data rates, number of planes etc. happen.
Introduce a flag to force qgv check in such cases.
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240405113533.338553-7-vinod.govindapillai@intel.com
There could be multiple qgv and psf gv points with similar values.
Apparently pcode's handling of psf and qgv points are different. For
qgv case, pcode sets whatever is asked by the driver. But in case
of psf gv points, it compares the bw from points before setting the
mask. This can cause problems in scenarios where we have to disable
sagv by setting the highest bw point and there could be multiple
points with highest bw. So to set the maximum psf gv point, find
out all the points with the highest bw and set all together.
v1: - use the same treatment to qgv points as well (Vinod)
v2: - pcode confirms that for qgv points, it sets whatever the
driver sets (Vinod)
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240405113533.338553-6-vinod.govindapillai@intel.com
Problem is that on some platforms, we do get QGV point mask in wrong
state on boot. However driver assumes it is set to 0
(i.e all points allowed), however in reality we might get them all
restricted, causing issues.
Lets disable SAGV initially to force proper QGV point state.
If more QGV points are available, driver will recalculate and update
those then after next commit.
v2: - Added trace to see which QGV/PSF GV point is used when SAGV is
disabled.
v3: - Move force disable function to intel_bw_init in order to initialize
bw state as well, so that hw/sw are immediately in sync after init.
v4: - Don't try sending PCode request, seems like it is not possible at
intel_bw_init, however assigning bw->state to be restricted as if
SAGV is off, still forces driveer to send PCode request anyway on
next modeset, so the solution still works.
However we still need to address the case, when no display is
connected, which anyway requires much more changes.
v5: - Put PCode request back and apply temporary hack to make the
request succeed(in case if there 2 PSF GV points with same BW, PCode
accepts only if both points are restricted/unrestricted same time)
- Fix argument sequence for adl_qgv_bw(Ville Syrjälä)
v6: - Fix wrong platform checks, not to break everything else.
v7: - Split the handling of quplicate QGV/PSF GV points (Vinod)
Restrict force disable to display version below 14 (Vinod)
v8: - Simplify icl_force_disable_sagv (Vinod)
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240405113533.338553-5-vinod.govindapillai@intel.com
We need that in order to force disable SAGV in next patch.
Also it is beneficial to separate that code, as in majority cases,
when SAGV is enabled, we don't even need those calculations.
Also we probably need to determine max PSF GV point as well, however
currently we don't do that when we disable SAGV, which might be
actually causing some issues in that case.
v2: - Introduce helper adl_qgv_bw(counterpart to adl_psf_bw)
(Ville Syrjälä)
- Don't restrict psf gv points for SAGV disable case
(Ville Syrjälä)
v3: - Update icl_max_bw_qgv_point_mask to return max qgv point
mask (Vinod)
v4: - Minor changes in icl_find_qgv_points (Vinod)
v5: - use max_bw_point instead of max_bw_point_mask (stan)
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240405113533.338553-3-vinod.govindapillai@intel.com
For debug purposes we need those - error path won't flood the log,
however there has been already numerous cases, when due to lack
of debugs, we couldn't immediately tell what was the problem on
customer machine, which slowed down the investigation, requiring
to get access to target device and adding those traces manually.
v2: - Make the debug more generic and move it to intel_dram_detect
(Gustavo Sousa)
v3: - Use %u for unsigned variable in debug prints (Gustavo)
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240405113533.338553-2-vinod.govindapillai@intel.com
Use the >= and < operators for the DISPLAY_VER checks everywhere.
This is what most of the code does, but especially recently random
pieces of code have started doing this differently for no good reason.
Conversion done with the following cocci:
@find@
expression i915;
constant ver;
@@
(
DISPLAY_VER(i915) <= ver
|
DISPLAY_VER(i915) > ver
)
@script:python inc@
old_ver << find.ver;
new_ver;
@@
coccinelle.new_ver = str(int(old_ver) + 1)
@@
expression find.i915;
constant find.ver;
identifier inc.new_ver;
@@
(
- DISPLAY_VER(i915) <= ver
+ DISPLAY_VER(i915) < new_ver
|
- DISPLAY_VER(i915) > ver
+ DISPLAY_VER(i915) >= new_ver
)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127145028.4899-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
MTL uses the peak BW of a QGV point to lock the required QGV
point instead of the QGV index. Instead of passing the deratedbw
of the selected bw_info, return the index to the selected
bw_info so that either deratedbw or peakbw can be used based on
the platform.
v2: use idx to store index returned by max_bw_index functions
v3: return UINT_MAX in icl_max_bw_index in case no match found
v3: check idx >= ARRAY_SIZE
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606093509.221709-6-vinod.govindapillai@intel.com
In MTL onwards, pcode locks the GV point based on the peak BW
of a QGV point. So store the peak BW of all the QGV points.
v2: use DIV_ROUND_CLOSEST() for the peakBW calculation
Bspec: 64636
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606093509.221709-4-vinod.govindapillai@intel.com
From MTL onwwards, pcode locks the QGV point based on peak BW of
the intended QGV point passed by the driver. So the peak BW
calculation must match the value expected by the pcode. Update
the calculations as per the Bspec.
v2: use DIV_ROUND_* macro for the calculations (Ville)
v3: Use only DIV_ROUN_CLOSEST and remove divisor / 2 again
Bspec: 64636
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606093509.221709-3-vinod.govindapillai@intel.com
Follow the values from bspec for the percentage overhead for
efficiency in MTL BW calculations.
Bspec: 64631
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606093509.221709-2-vinod.govindapillai@intel.com
Communicating QGV points restriction to PUnit happens via PM Demand
instead of the Pcode mailbox in the previous platforms. GV point
restriction is handled by the PM demand code.
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318005852.2303937-5-radhakrishna.sripada@intel.com
On icl+ SAGV is controlled by masking of the QGV points.
Reduce the QGV point mask to the same kind of enabled vs.
disable information that we had on previous platforms.
Will be useful in answering the question whether SAGV is
actually enabled or not.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230131002127.29305-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
MTL LPDDR5 reported 16b with 8 channels. Previous platforms
reported 32b with 4 channels and hence needed a multiplication
by a factor of 2. Skip increasing the channels for MTL.
v2: Use version check instead of platform check(MattR)
Bspec: 64631
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221117213015.584417-2-radhakrishna.sripada@intel.com
From Meteorlake, Latency Level, SAGV bloack time are read from
LATENCY_SAGV register instead of the GT driver pcode mailbox. DDR type
and QGV information are also to be read from Mem SS registers.
v2:
- Simplify MTL_MEM_SS_INFO_QGV_POINT macro(MattR)
- Nit: Rearrange the bit def's from higher to lower(MattR)
- Restore platform definition for ADL-P(MattR)
- Move back intel_qgv_point def to intel_bw.c(Jani)
v3:
- Rebase
Bspec: 64636, 64608
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Original Author: Caz Yokoyama
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220902060342.151824-9-radhakrishna.sripada@intel.com
Pull all the skl+ watermark code (and the dbuf/sagv/ipc code
since it's all sort of intertwined and I'm too lazy to think
of a finer grained split right now) into its own file from the
catch-all intel_pm.c.
Also sneak in the s/dev_priv/i915/ rename while at it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908191646.20239-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Like ADL_P, Meteorlake has different memory characteristics from
past platforms. Update the values used by our memory bandwidth
calculations accordingly.
Bspec: 64631
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220818234202.451742-17-radhakrishna.sripada@intel.com
Each gt contains an independent instance of pcode. Extend pcode functions
to interface with pcode on different gt's. To avoid creating dependency of
display functionality on intel_gt, pcode function interfaces are exposed in
terms of uncore rather than intel_gt. Callers have been converted to pass
in the appropritate (i915 or intel_gt) uncore to the pcode functions.
v2: Expose pcode functions in terms of uncore rather than gt (Jani/Rodrigo)
v3: Retain previous function names to eliminate needless #defines (Rodrigo)
v4: Move out i915_pcode_init() to a separate patch (Tvrtko)
Remove duplicated drm_err/drm_dbg from intel_pcode_init() (Tvrtko)
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220519085732.1276255-2-tvrtko.ursulin@linux.intel.com
[tursulin: fixup merge conflict]
Update DG2 init bw info similar to other platforms even though
DG2 has constant bandwidh. This will avoid branching out DG2
specific max bw calls.
V3: Fix dg2_get_bw_info() and avoid handle special cases
for DG2 (Ville Syrjälä)
cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220328230000.215094-1-vinod.govindapillai@intel.com
Continuation of the effort to declutter i915_drv.h.
Also, component specific helpers which consult the iommu/virtualization
helpers moved to respective component source/header files as appropriate.
v2:
* s/dev_priv/i915/ in intel_scanout_needs_vtd_wa. (Lucas)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220329090204.2324499-1-tvrtko.ursulin@linux.intel.com
[tursulin: fixup conflict in i915_drv.h]
Make the dbuf bandwidth min cdclk calculations match the spec
more closely. Supposedly the arbiter can only guarantee an equal
share of the total bandwidth of the slice to each active plane
on that slice. So we take the max bandwidth of any of the planes
on each slice and multiply that by the number of active planes
on the slice to get a worst case estimate on how much bandwidth
we require.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303191207.27931-9-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
The current code also forgets to call intel_atomic_lock_global_state()
when other stuff besides the final min_cdlck changes in the state.
That means we may throw away data which actually has changed, and
thus we can't be at all sure what the code ends up doing during
subsequent commits. Do the write lock properly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303191207.27931-8-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
intel_bw_calc_min_cdclk() is entirely pointless. All it manages to do is
somehow conflate the per-pipe min cdclk with dbuf min cdclk. There is no
(at least documented) dbuf min cdclk limit on pre-skl so let's just get
rid of all this confusion.
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303191207.27931-6-ville.syrjala@linux.intel.com
Split the currently combined plane data_rate into the proper
Y vs. CbCr components. This matches how we now track the
plane dbuf allocations, and thus will make the dbuf bandwidth
calculations actually produce the correct numbers for each
dbuf slice.
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303191207.27931-3-ville.syrjala@linux.intel.com
Let's store the plane allocation in a manner which more closely
matches how the hw operates. That is, we store the packed/CbCr
ddb in one struct, and the Y ddb in another. Currently we're
storing packed/Y in one struct, CbCr in the other.
This also works pretty well for icl+ where the UV plane is
the main plane and the Y plane is subservient to it. Although
in this case we do not even use ddb_y as we do the ddb allocation
in terms of hw planes.
v2: Rebase
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303191207.27931-2-ville.syrjala@linux.intel.com
Don't just mask off all the PSF GV points when SAGV gets disabled.
This should in fact cause the Pcode to reject the request since
at least one PSF point must remain enabled at all times.
Cc: stable@vger.kernel.org
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: 192fbfb767 ("drm/i915: Implement PSF GV point support")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220309164948.10671-7-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
If the only thing that is changing is SAGV vs. no SAGV but
the number of active planes and the total data rates end up
unchanged we currently bail out of intel_bw_atomic_check()
early and forget to actually compute the new WGV point
mask and thus won't actually enable/disable SAGV as requested.
This ends up poorly if we end up running with SAGV enabled
when we shouldn't. Usually ends up in underruns.
To fix this let's go through the QGV point mask computation
if either the data rates/number of planes, or the state
of SAGV is changing.
v2: Check more carefully if things are changing to avoid
the extra calculations/debugs from introducing unwanted
overhead
Cc: stable@vger.kernel.org
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> #v1
Fixes: 20f505f225 ("drm/i915: Restrict qgv points which don't have enough bandwidth.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218064039.12834-3-ville.syrjala@linux.intel.com
Registers that exist within the MCH BAR and are mirrored into the GPU's
MMIO space are a good candidate to separate out into their own header.
For reference, the mirror of the MCH BAR starts at the following
locations in the graphics MMIO space (the end of the MCHBAR range
differs slightly on each platform):
* Pre-gen6: 0x10000
* Gen6-Gen11 + RKL: 0x140000
v2:
- Create separate patch to swtich a few register definitions to be
relative to the MCHBAR mirror base.
- Drop upper bound of MCHBAR mirror from commit message; there are too
many different combinations between various platforms to list out,
and the documentation is spotty for the older pre-gen6 platforms
anyway.
Bspec: 134, 51771
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220215061342.2055952-2-matthew.d.roper@intel.com
Several of our i915 header files, have been including i915_reg.h. This
means that any change to i915_reg.h will trigger a full rebuild of
pretty much every file of the driver, even those that don't have any
kind of register access. Let's delete the i915_reg.h include from all
headers and add an explicit include from the .c files that truly
need the register definitions; those that need a definition of
i915_reg_t for a function definition can get it from i915_reg_defs.h
instead.
We also remove two non-register #define's (VLV_DISPLAY_BASE and
GEN12_SFC_DONE_MAX) into i915_reg_defs.h to allow us to drop the
i915_reg.h include from a couple of headers.
There's probably a lot more header dependency optimization possible, but
the changes here roughly cut the number of files compiled after 'touch
i915_reg.h' in half --- a good first step.
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127234334.4016964-7-matthew.d.roper@intel.com
Catch-up with 5.17-rc2 and trying to align with drm-intel-gt-next
for a possible topic branch for merging the split of i915_regs...
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
With both integrated and discrete Intel GPUs in a system, the current
global check of intel_iommu_gfx_mapped, as done from intel_vtd_active()
may not be completely accurate.
In this patch we add i915 parameter to intel_vtd_active() in order to
prepare it for multiple GPUs and we also change the check away from Intel
specific intel_iommu_gfx_mapped (global exported by the Intel IOMMU
driver) to probing the presence of IOMMU on a specific device using
device_iommu_mapped().
This will return true both for IOMMU pass-through and address translation
modes which matches the current behaviour. If in the future we wanted to
distinguish between these two modes we could either use
iommu_get_domain_for_dev() and check for __IOMMU_DOMAIN_PAGING bit
indicating address translation, or ask for a new API to be exported from
the IOMMU core code.
v2:
* Check for dmar translation specifically, not just iommu domain. (Baolu)
v3:
* Go back to plain "any domain" check for now, rewrite commit message.
v4:
* Use device_iommu_mapped. (Robin, Baolu)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211126141424.493753-1-tvrtko.ursulin@linux.intel.com
The earlier update to BW formulae broke ADL-P. Include
display 13 to use TGL path for BW parameters.
Fixes: c64a9a7c05 ("drm/i915: Update memory bandwidth formulae")
Cc: Matt Roper <matthew.d.roper@intel.com>
Reported-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Caz Yokoyama <caz.yokoyama@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211106003714.17894-1-radhakrishna.sripada@intel.com
The formulae has been updated to include more variables. Make
sure the code carries the same.
Bspec: 64631, 54023
v2: Make GEN11 follow the default route and fix calculation of
maxdebw(RK)
v3: Fix div by zero on default case
Correct indent for fallthrough(Jani)
v4: Fix div by zero on gen11.
v5: Fix 0 max_numchannels case
v6:
- Split gen11/gen12 algorithms
- Fix RKL deburst value
- Fix difference b/ween ICL and TGL algorithms
- Protect deinterleave from being 0
- Warn when numchannels exceeds max_numchannels
- Fix scaling of clk_max from different units
- s/deinterleave/channelwidth/ in calculating peakbw
- Fix off by one for num_planes TGL+
- Fix SAGV check
v7: Fix div by zero error on gen11
v8: Even though the algorithm for gen11 says that we need to return
derated bw for a qgv point whose planes are less than no of active
planes, we return 0 for deratedbw when only one plane is allowed.
We modify the algorithm to accommodate the case where no of active
planes are same as the min no of planes supported by a qgv point.
v9: Fix dclk scaling for dg1
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015210041.16858-1-radhakrishna.sripada@intel.com
The snb+ pcode mailbox code is not sideband, so split it out to a
separate file. As can be seen from the #include changes, very few places
use both sideband and pcode.
Code movement only.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/185deb18eb739e5ae019e27834b9997dcc1347bc.1634207064.git.jani.nikula@intel.com
Earlier while calculating derated bw we would use 90% of the calculated
bw. Starting ADL-P we use a non standard derating. Updating the formulae
to reflect the same.
Bspec: 64631
v2: Use the new derating value only for ADL-P(MattR)
Fixes: 4d32fe2f14 ("drm/i915/adl_p: Update memory bandwidth parameters")
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914220744.16042-1-radhakrishna.sripada@intel.com
PSF GV points are an additional factor that can limit the
bandwidth available to display, separate from the traditional
QGV points. Whereas traditional QGV points represent possible
memory clock frequencies, PSF GV points reflect possible
frequencies of the memory fabric.
Switching between PSF GV points has the advantage of incurring
almost no memory access block time and thus does not need to be
accounted for in watermark calculations.
This patch adds support for those on top of regular QGV points.
Those are supposed to be used simultaneously, i.e we are always
at some QGV and some PSF GV point, based on the current video
mode requirements.
Bspec: 64631, 53998
v2: Seems that initial assumption made during ml conversation
was wrong, PCode rejects any masks containing points beyond
the ones returned, so even though BSpec says we have around
8 points theoretically, we can mask/unmask only those which
are returned, trying to manipulate those beyond causes a
failure from PCode. So switched back to generating mask
from 1 - num_qgv_points, where num_qgv_points is the actual
amount of points, advertised by PCode.
v3: - Extended restricted qgv point mask to 0xf, as we have now
3:2 bits for PSF GV points(Matt Roper)
- Replaced val2 with NULL from PCode request, since its not being
used(Matt Roper)
- Replaced %d to 0x%x for better readability(thanks for spotting)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210531064845.4389-2-stanislav.lisovskiy@intel.com
