Mixing VBT based AUX CH with platform defaults seems like
a recipe for conflicts. Let's only populate AUX CH if we
absolutely need it, that is only if we are dealing with
a DP output or a TC port (which need it due to some power
well shenanigans).
TODO: double check that real VBTs do in fact populate
the AUX CH for HDMI TC legacy ports...
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230630155846.29931-3-ville.syrjala@linux.intel.com
Make HSW/BDW use port_mask for output probing as well.
To achieve that the strap checks are moved into
intel_ddi_init() itself. Or should we move them to the
runtime port_mask init instead? Maybe not since the hardware
is still there, just not connected to anything.
v2: Account for DDI-E in strap detection
Keep to the old CRT->DDI init order
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-8-ville.syrjala@linux.intel.com
Sprinkle some asserts to catch any mishaps in the port_mask
vs. output init.
For DDI/DP/HDMI/SDVO I decided that we want to bail out for
an invalid port since those are the encoder types where
we might want consider driving the whole thing from the VBT
child device list, and bogus VBTs could be a real issue
(if for no other reason than the i915.vbt_firmware).
For DVO and HSW/BDW CRT port I just threw the assert in
there for good measure.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-5-ville.syrjala@linux.intel.com
If the output on a DP-alt link with its sink disconnected is kept
enabled for too long (about 20 sec), then some IOM/TCSS firmware timeout
will cause havoc on the PCI bus, at least for other GFX devices on it
which will stop powering up. Since user space is not guaranteed to do a
disabling modeset in time, switch such disconnected but active links to
TBT mode - which is without such shortcomings - with a 2 second delay.
If the above condition is detected already during the driver load/system
resume sanitization step disable the output instead, as at that point no
user space or kernel client depends on a consistent output state yet and
because subsequent atomic modeset on such connectors - without the
actual sink capabilities available - can fail.
An active/disconnected port as above will also block the HPD status of
other active/disconnected ports to get updated (stuck in the connected
state), until the former port is disabled, its PHY is disconnected and
a ~10 ms delay has elapsed. This means the link state for all TypeC
ports/CRTCs must be rechecked after a CRTC is disabled due to the above
reason. For this disconnect the PHY synchronously after the CRTC/port is
disabled and recheck all CRTCs for the above condition whenever such a
port is disabled.
To account for a race condition during driver loading where the sink is
disconnected after the above sanitization step and before the HPD
interrupts get enabled, do an explicit check/link reset if needed from
the encoder's late_register hook, which is called after the HPD
interrupts are enabled already.
v2:
- Handle an active/disconnected port blocking the HPD state update of
another active/disconnected port.
- Cancel the delayed work resetting the link also from the encoder
enable/suspend/shutdown hooks.
- Rebase on the earlier intel_modeset_lock_ctx_retry() addition,
fixing here the missed atomic state reset in case of a retry.
- Fix handling of an error return from intel_atomic_get_crtc_state().
- Recheck if the port needs to be reset after all the atomic state
is locked and async commits are waited on.
v3:
- Add intel_crtc_needs_link_reset(), instead of open-coding it,
keep intel_crtc_has_encoders(). (Ville)
- Fix state dumping and use a bitmask to track disabled CRTCs in
intel_sanitize_all_crtcs(). (Ville)
- Set internal in intel_atomic_state right after allocating it.
(Ville)
- Recheck all CRTCs (not yet force-disabled) after a CRTC is
force-disabled for any reason (not only due to a link state)
in intel_sanitize_all_crtcs().
- Reduce delay after CRTC disabling to 20ms, and use the simpler
msleep().
- Clarify code comment about HPD behaviour in
intel_sanitize_all_crtcs().
- Move all the TC link reset logic to intel_tc.c .
- Cancel the link reset work synchronously during system suspend,
driver unload and shutdown.
v4:
- Rebased on previous patch, which allows calling the TC port
suspend/cleanup handlers without modeset locks held; remove the
display driver suspended assert from the link reset work
accordingly.
v5: (Ville)
- Remove reset work canceling from intel_ddi_pre_pll_enable().
- Track a crtc vs. pipe mask in intel_sanitize_all_crtcs().
- Add reset_link_commit() to clarify the
intel_modeset_lock_ctx_retry loop.
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5860
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512195513.2699-2-imre.deak@intel.com
Call the TypeC port flush_work and cleanup handlers without the modeset
locks held. These don't require the locks, as the work takes - as it
should be able to at any point in time - any locks it needs and by the
time cleanup is called and after cleanup returns the encoder is not in
use.
This is required by the next patch canceling a TypeC port work
synchronously during encoder suspend and shutdown, where the work can
take modeset locks as well, hence the canceling must be done without
holding the locks.
I also considered moving the modeset locking down to each encoder
suspend()/shutdown() hook instead, however locking the full modeset
state for each encoder separately would be odd, and the bigger change -
affecting all encoders - is beyond the scope of this patchset.
v2:
- Add a TODO: comment to remove modeset locks if no encoder depends
on this. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512195513.2699-1-imre.deak@intel.com
This patch simplifying the handling of modeset locks and atomic state
for an atomic commit is based on
https://lore.kernel.org/all/20210715184954.7794-2-ville.syrjala@linux.intel.com/
adding the helper to i915. I find this approach preferrable than
open-coding the corresponding steps (fixed for me an atomic
state reset during a DEADLK retry, which I missed in the open-coded
version) and also better than the existing
DRM_MODESET_LOCK_ALL_BEGIN/END macros for the reasons described in the
above original patchset.
This change takes the helper into use only for atomic commits during DDI
hotplug handling, as a preparation for a follow-up patch adding a
similar commit started from the same spot. Other places doing a
driver-internal atomic commit is to be converted by a follow-up
patchset.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-13-imre.deak@intel.com
Pass all the parameter in intel_encoder->enable()
to intel_hdcp_enable as we need intel_atomic_state
later down to get acquire_ctx.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230515103225.688830-2-suraj.kandpal@intel.com
We'll be wanting to compute has_hdmi_sink a bit differently
for some platforms. To that end compute it in the encoder
.compute_config_hook() before we call intel_hdmi_compute_config().
intel_hdmi_compute_has_hdmi_sink() will do the basic lifting
beyond any platform specific stuff.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221107194604.15227-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Add register writes to enable powering up Type-C subsystem i.e. TCSS.
For MeteorLake we need to request TCSS to power up and check the TCSS
power state after 500 us.
In addition, for PICA we need to set/clear the Type-C PHY ownnership
bit when Type-C device is connected/disconnected.
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-11-mika.kahola@intel.com
As we already do with C10 chip, let's dump the pll
hw state for C20 as well.
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-4-mika.kahola@intel.com
Create a table for C20 DP1.4, DP2.0 and HDMI2.1 rates.
The PLL settings are based on table, not for algorithmic alternative.
For DP 1.4 only MPLLB is in use.
Once register settings are done, we read back C20 HW state.
BSpec: 64568
v2: Updated pll tables (RK)
MPLLB selection fix (RK)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-3-mika.kahola@intel.com
C20 phy PLL programming sequence for DP, DP2.0, HDMI2.x non-FRL and
HDMI2.x FRL. This enables C20 MPLLA and MPLLB programming sequence. add
4 lane support for c20.
v2: Add 6.48Gbps and 6.75Gbps modes for eDP (RK)
Fix lane check (RK)
Fix multiline commenting (Arun)
use usleep_range() instead of msleep() (Andi)
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Bhanuprakash Modem <bhanuprakash.modem@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-2-mika.kahola@intel.com
The port PLL selection needs to be up-to-date in the CRTC state of both
the primary and all secondary MST streams. The commit removing the
encoder update_prepare/complete hooks (see Fixes: below), stopped doing
this for secondary streams, fix this up.
Fixes: 0f752b2178 ("drm/i915: Remove the encoder update_prepare()/complete() hooks")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8336
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230414173800.590790-1-imre.deak@intel.com
(cherry picked from commit 27ac123b45)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The port PLL selection needs to be up-to-date in the CRTC state of both
the primary and all secondary MST streams. The commit removing the
encoder update_prepare/complete hooks (see Fixes: below), stopped doing
this for secondary streams, fix this up.
Fixes: 0f752b2178 ("drm/i915: Remove the encoder update_prepare()/complete() hooks")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8336
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230414173800.590790-1-imre.deak@intel.com
MTL requires the PORT_CTL_WIDTH, TRANS_DDI_FUNC_CTL and DDI_BUF_CTL
to be filled with 4 lanes for TMDS mode.
This patch enables D2D link and fills PORT_WIDTH in appropriate
registers.
v2:
- Added fixes from Clint's Add HDMI implementation changes.
- Modified commit message.
v3:
- Use TRANS_DDI_PORT_WIDTH() instead of DDI_PORT_WIDTH() for the value
of TRANS_DDI_FUNC_CTL_*. (Gustavo)
Cc: Taylor, Clinton A <clinton.a.taylor@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-9-radhakrishna.sripada@intel.com
The differences between MTL and TGL DP sequences are big enough to
MTL have its own functions.
Also it is much easier to follow MTL sequences against spec with
its own functions.
One change worthy to mention is the move of
'intel_display_power_get(dev_priv, dig_port->ddi_io_power_domain)'.
This call is not necessary for MTL but we have _put() counter part in
intel_ddi_post_disable_dp() that needs to balanced.
We could add a display version check on it but instead here it is
moving it to intel_ddi_pre_enable_dp() so it is executed for all
platforms in a single place and this will not cause any harm in MTL
and newer platforms.
v2:
- Fix logic to wait for buf idle.
- Use the right register to wait for ddi active.(RK)
v3:
- Increase wait timeout for ddi buf active (Mika)
v4:
- Increase idle timeout for ddi buf idle (Mika)
v5: use rmw in mtl_disable_ddi_buf. Donot clear
link training mask(Imre)
BSpec: 65448 65505
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Satyeshwar Singh <satyeshwar.singh@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-7-radhakrishna.sripada@intel.com
C10 phys uses direct mapping internally for voltage and pre-emphasis levels.
Program the levels directly to the fields in the VDR Registers.
Bspec: 65449
v2: From table "C10: Tx EQ settings for DP 1.4x" it shows level 1
and preemphasis 1 instead of two times of level 1 preemphasis 0.
Fix this in the driver code as well.
v3: VSwing update (Clint)
v4: Add vboost termination ctl programming(Imre)
Fix tx llogic and other nits
Restrict C10 vdr ctl register access for C10 phy(RK)
v5: Program vboots, termination ctl for both lanes(Imre)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>(v3)
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-5-radhakrishna.sripada@intel.com
XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy
has a dedicated PIPE 5.2 Message bus for configuration. This message
bus is used to configure the phy internal registers.
XELPDP has C10 phys to drive output to the EDP and the native output
from the display engine. Add structures, programming hardware state
readout logic. Port clock calculations are similar to DG2. Use the DG2
formulae to calculate the port clock but use the relevant pll signals.
Note: PHY lane 0 is always used for PLL programming.
Add sequences for C10 phy enable/disable phy lane reset,
powerdown change sequence and phy lane programming.
Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636
v2: Squash patches related to C10 phy message bus and pll
programming support (Jani)
Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani)
Move macro definitions (Jani)
DP rates as separate patch (Jani)
Spin out xelpdp register definitions into a separate file (Jani)
Replace macro to select registers based on phy lane with
function calls (Jani)
Fix styling issues (Jani)
Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas)
v3: Move clear request flag into try-loop
v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani)
use __intel_de_wait_for_register() instead of __intel_wait_for_register
and uncomment intel_uncore.h (Jani)
Add DP-alt support for PHY lane programming (Khaled)
v4: Add tx and cmn on c10mpllb_state (Imre)
Add missing waits for pending transactions between two message bus
writes (Imre)
General cleanups and simplifications (Imre)
v5: Few nit cleanups from rev4 (imre)
s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK)
Rebase
v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function
Fix typo in comment for REG_FIELD_PREP8 definition(Imre)
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v4)
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
If we have to force the hardware to go through a full modeset
due to eg. cdclk reprogramming, we need to preserve
crtc_state->inherited for all crtcs that have not otherwise
gone through the whole compute_config() stuff after connectors
have been detected.
Otherwise eg. cdclk induced modeset glk_force_audio_cdclk()
will clear the inherited flag, and thus the first real commit
coming from userspace later on will not be forced through
the full .compute_config() path and so eg. audio state may
not get properly recomputed.
But instead of adding all kinds of ad-hoc crtc_state->inherited
preservation hacks all over, let's change things so that we
only clear it for the crtcs directly included in userspace/client
initiated commits.
Should be far less fragile since now we just need to remember
to flag the internal commits, and not worry about where new
crtcs might get pulled in.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5260
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230328122357.1697-1-ville.syrjala@linux.intel.com
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Move VRR enabling/disabling into a place where it also works
for fastsets.
With this we always start the transcoder up in non-VRR mode.
Granted we already did that but for a very short period of
time. But now that we might end up doing a bit more with the
transcoder in non-VRR mode it seems prudent to also update
the active timings as the transcoder changes its operating
mode.
crtc_state->vrr.enable still tracks whether VRR is actually
enabled or not, but now we configure all the other VRR timing
registers whenever VRR is possible (whether we actually enable
it or not). crtc_state->vrr.flipline can now serve as our
"is VRR possible" bit of state.
I decided to leave the MSA timing ignore bit set all the time
whether VRR is actually enabled or not. If the sink can figure
out the timings with that information when VRR is active then
surely it can also do it when VRR is inactive.
v2: Protect intel_vrr_set_transcoder_timings() with HAS_VRR()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321135615.27338-1-ville.syrjala@linux.intel.com
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
- i915.enable_sagv module parameter (Ville)
- Correction to QGV related register addresses (Vinod)
- IPS debugfs per-crtc and new file for false_color (Ville)
- More clean-up and reorganization of Display code (Jani)
- DP DSC related fixes and improvements (Stanislav, Ankit, Suraj, Swati)
- Make utility pin asserts more accurate (Ville)
- Meteor Lake enabling (Daniele)
- High refresh rate PSR fixes (Jouni)
- Cursor and Plane chicken register fixes (Ville)
- Align the ADL-P TypeC sequences with hardware specification (Imre)
- Documentation build fixes and improvements to catch bugs earlier (Lee, Jani)
- PL1 power limit hwmon entry changed to use 0 as disabled state (Ashutosh)
- DP aux sync fix and improvements (Ville)
- DP MST fixes and w/a (Stanislav)
- Limit PXP drm-errors or warning on firmware API failures (Alan)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAmQu0TIACgkQ+mJfZA7r
E8osJwf+Pi3tvP1gvum4aVM2IgjA9fF1ZTwwFDqVNwJ2Sfzb93E0XOetoqd0AsEa
z6XYKN5N6P+dA1zLdtV21cmmI3V0iC7UEoZVba98n6Euabh0+7sDcS6o9Y7wDLqJ
DsDL02Vb2OMNjHce+w2lvbiLU52pWh9hVpB47bqS/vjTE9Q+C0Y2PoReyTca6o63
wmOXd1LSNfmaXHfeTRwQdWD7XlHtVmZmH0vn3BSd1ikB0nT7BJIIdc96fody19DI
67CLhQANhesp5si9JIqTWdxSgEibxFP9xDqfx3FOGJfhxWuOPSTs8hk/OjXM3zjr
2uSOnqxZ4a+nrSXy6pG4R4PqvG6ljg==
=Yqy1
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2023-04-06' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
- Fix DPT+shmem combo and add i915.enable_dpt modparam (Ville)
- i915.enable_sagv module parameter (Ville)
- Correction to QGV related register addresses (Vinod)
- IPS debugfs per-crtc and new file for false_color (Ville)
- More clean-up and reorganization of Display code (Jani)
- DP DSC related fixes and improvements (Stanislav, Ankit, Suraj, Swati)
- Make utility pin asserts more accurate (Ville)
- Meteor Lake enabling (Daniele)
- High refresh rate PSR fixes (Jouni)
- Cursor and Plane chicken register fixes (Ville)
- Align the ADL-P TypeC sequences with hardware specification (Imre)
- Documentation build fixes and improvements to catch bugs earlier (Lee, Jani)
- PL1 power limit hwmon entry changed to use 0 as disabled state (Ashutosh)
- DP aux sync fix and improvements (Ville)
- DP MST fixes and w/a (Stanislav)
- Limit PXP drm-errors or warning on firmware API failures (Alan)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZC7RR3Laet8ywHRo@intel.com
Include the device and connector information in the SCDC
debugs. Makes it easier to figure out who did what.
v2: Rely on connector->ddc (Maxime)
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Robert Foss <rfoss@kernel.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Emma Anholt <emma@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230403223652.18848-1-ville.syrjala@linux.intel.com
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The encoder update_prepare()/complete() hooks were added to hold a
TC port link reference for all outputs in the atomic state around the
whole modeset enable sequence - thus locking the ports' TC mode - and
set the TBT/DP-alt PLL type corresponding to the current TC mode.
Since nothing depends on the PLL selection before/after then encoder's
pre_pll_enable/post_pll_disable hooks are called, the above steps can be
moved to these hooks, so do that and remove the
update_prepare()/complete() hooks.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-30-imre.deak@intel.com
Bspec requires disabling the DPLLs on TC ports before disconnecting the
port's PHY. Add a post_pll_disable encoder hook and move the call to
disconnect the port's PHY from the post_disable hook to the new hook.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-28-imre.deak@intel.com
For clarity factor out the function to determine if there are active
links on a TC port. This prepares for the next patch also checking the
port's PLL type.
While at it pass crtc_state to intel_tc_port_sanitize_mode(), and check
hw.active in that, instead of the deprecated crtc->active flag.
v2: Check crtc_state->hw.active instead of crtc->active. (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321220101.983366-2-imre.deak@intel.com
Add an encoder hook, which can be called on enabled TC ports to
determine if the port uses a TBT or a non-TBT PLL. An upcoming patch
will use this to sanity check active TC port's PHY state wrt. the PLL
type used by the port.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-13-imre.deak@intel.com
Since an HDMI output can only be enabled in legacy mode on TC ports,
assume that VBT is wrong and the port is legacy if VBT says the port is
non-legacy and has HDMI. If VBT says to enable DP as well leave the
non-legacy flag enabled, relying on the flag getting fixed up based on
the HPD status during sink detection.
v2: Fix the legacy port flag only if DP is not enabled.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321220101.983366-1-imre.deak@intel.com
Enable SDP error detection configuration, this will set CRC16 in
128b/132b link layer.
For Display version 13 a hardware bit31 in register VIDEO_DIP_CTL is
added to enable/disable SDP CRC applicable for DP2.0 only, but the
default value of this bit will enable CRC16 in 128b/132b hence
skipping this write.
Corrective actions on SDP corruption is yet to be defined.
v2: Moved the CRC enable to link training init(Jani N)
v3: Moved crc enable to ddi pre enable <Jani N>
v4: Separate function for SDP CRC16 (Jani N)
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230302081532.765821-3-arun.r.murthy@intel.com
AFAICS Bspec has never asked us to switch to TPS1 when *disabling*
DP_TP_CTL. Let's stop doing that in case it confuses something.
We do have to switch before we *enable* DP_TP_CTL, but that
is already being handled correctly.
v2: Do the same for FDI
v3: Rebase
Reviewed-by: Imre Deak <imre.deak@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230308212627.7601-1-ville.syrjala@linux.intel.com
SKL doesn't have any north DE hotplug stuff. Currently we're
trying to read DDI A live state from the BDW north DE bit,
instead of the approproate south DE bit. Fix it.
And for good measure clear the pointer to the north hpd
pin array, so that we'll actually notice if some other
place is also using the wrong thing.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230302161013.29213-3-ville.syrjala@linux.intel.com
We'll need dig_port->connected() to be there for a HPD live
state check during eDP connector probing. Reorder intel_ddi_init()
accordingly. g4x_dp_init() is already fine.
v2: Fix comment style while at it
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230302161013.29213-2-ville.syrjala@linux.intel.com
Use an early return to get rid of the extra indentation level
in intel_ddi_{enable,disable}_transcoder_clock().
Also unify the platform handling in between the two while at
it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Restructure intel_bios_port_aux_ch() to resemble the ddc_pin
counterpart, where the intel_bios.c stuff only deals with the
child device definition, and the platform default will come from
elsewhere.
This requires the introduction of AUX_CH_NONE as the value 0
is already taken to mean AUX_CH_A.
v2: Sort includes alphabetically (Ankit)
vCould we ask them to do a BIOS fix for all of them so that
we wouldn't keep getting these bug reports for each model
separately?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216231312.32664-1-ville.syrjala@linux.intel.com
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Switch a lot of the intel_bios_foo() stuff to just accept the
devdata (VBT child device info) directly, instead of taking
detours via vbt.ports[].
Also unify the function naming scheme.
v2: Drop the redundant "encoder" from the dp/hdmi specific functions
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216000425.32216-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Currently intel_bios_port_aux_ch() digs out the devdata
(VBT child device info) from the vbt.ports[] array. We
need to get rid of that, so just pass in the correct
encoder->devdata (now that we have it also for g4x+ ports)
directly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The sole user of intel_bios_is_lane_reversal_needed() has
the devdata already located, so pass it in directly instead
of digging it again from vbt.ports[].
And rename the function to follow the common pattern for
these things.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We always have encoder->devdata available on the platforms
that can have LSPCON. So let's start looking there instead
of digging it out from vbt.ports[].
And let's rename the function to fit the common pattern
for these things.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
