Add support for the A750 GPU found on the SM8650 platform
Unlike the the very close A740 GPU on the SM8550 SoC, the A750 GPU
doesn't have an HWCFG block but a separate register set.
The A750 GPU info are added under the adreno_is_a750() macro and
the ADRENO_7XX_GEN3 family id.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/578693/
Signed-off-by: Rob Clark <robdclark@chromium.org>
This updates the GPU headers to latest from mesa, using gen_header.py
(which is used to generate headers at bulid time for mesa), rather than
headergen2 (which doesn't have proper support for A6XX vs A7XX register
variants).
Mostly just uninteresting churn, but there are a couple spots in a7xx
paths which update REG_A6XX_foo to REG_A7XX_foo for registers which are
a7xx specific.
Cc: Connor Abbott <cwabbott0@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/574880/
The commit referenced in the Fixes tag had a couple problems (as
pointed out by Dan):
- qmp_put was never called, resulting in refcnt leaks
- failling to acquire the QMP mailbox on A7xx would not undo the probe
function properly
- the qmp_put call present in the code was unreachable
Fix all of these issues.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 88a0997f2f ("drm/msm/a6xx: Send ACD state to QMP at GMU resume")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/562761/
Signed-off-by: Rob Clark <robdclark@chromium.org>
A740 builds upon the A730 IP, shuffling some values and registers
around. More differences will appear when things like BCL are
implemented.
adreno_is_a740_family is added in preparation for more A7xx GPUs,
the logic checks will be valid resulting in smaller diffs.
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # sm8450
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/559291/
Signed-off-by: Rob Clark <robdclark@chromium.org>
The QMP mailbox expects to be notified of the ACD (Adaptive Clock
Distribution) state. Get a handle to the mailbox at probe time and
poke it at GMU resume.
Since we don't fully support ACD yet, hardcode the message to "val: 0"
(state = disabled).
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # sm8450
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/559287/
Signed-off-by: Rob Clark <robdclark@chromium.org>
A7xx GPUs are - from kernel's POV anyway - basically another generation
of A6xx. They build upon the A650/A660_family advancements, skipping some
writes (presumably more values are preset correctly on reset), adding
some new ones and changing others.
One notable difference is the introduction of a second shadow, called BV.
To handle this with the current code, allocate it right after the current
RPTR shadow.
BV handling and .submit are mostly based on Jonathan Marek's work.
All A7xx GPUs are assumed to have a GMU.
A702 is not an A7xx-class GPU, it's a weird forked A610.
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # sm8450
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/559285/
Signed-off-by: Rob Clark <robdclark@chromium.org>
core:
- fix gfp flags in drmm_kmalloc
gpuva:
- add new generic GPU VA manager (for nouveau initially)
syncobj:
- add new DRM_IOCTL_SYNCOBJ_EVENTFD ioctl
dma-buf:
- acquire resv lock for mmap() in exporters
- support dma-buf self import automatically
- docs fixes
backlight:
- fix fbdev interactions
atomic:
- improve logging
prime:
- remove struct gem_prim_mmap plus driver updates
gem:
- drm_exec: add locking over multiple GEM objects
- fix lockdep checking
fbdev:
- make fbdev userspace interfaces optional
- use linux device instead of fbdev device
- use deferred i/o helper macros in various drivers
- Make FB core selectable without drivers
- Remove obsolete flags FBINFO_DEFAULT and FBINFO_FLAG_DEFAULT
- Add helper macros and Kconfig tokens for DMA-allocated framebuffer
ttm:
- support init_on_free
- swapout fixes
panel:
- panel-edp: Support AUO B116XAB01.4
- Support Visionox R66451 plus DT bindings
- ld9040: Backlight support, magic improved,
Kconfig fix
- Convert to of_device_get_match_data()
- Fix Kconfig dependencies
- simple: Set bpc value to fix warning; Set connector type for AUO T215HVN01;
Support Innolux G156HCE-L01 plus DT bindings
- ili9881: Support TDO TL050HDV35 LCD panel plus DT bindings
- startek: Support KD070FHFID015 MIPI-DSI panel plus DT bindings
- sitronix-st7789v: Support Inanbo T28CP45TN89 plus DT bindings;
Support EDT ET028013DMA plus DT bindings; Various cleanups
- edp: Add timings for N140HCA-EAC
- Allow panels and touchscreens to power sequence together
- Fix Innolux G156HCE-L01 LVDS clock
bridge:
- debugfs for chains support
- dw-hdmi: Improve support for YUV420 bus format
CEC suspend/resume, update EDID on HDMI detect
- dw-mipi-dsi: Fix enable/disable of DSI controller
- lt9611uxc: Use MODULE_FIRMWARE()
- ps8640: Remove broken EDID code
- samsung-dsim: Fix command transfer
- tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
- adv7511: Fix low refresh rate
- anx7625: Switch to macros instead of hardcoded values
locking fixes
- tc358767: fix hardware delays
- sitronix-st7789v: Support panel orientation; Support rotation
property; Add support for Jasonic
JT240MHQS-HWT-EK-E3 plus DT bindings
amdgpu:
- SDMA 6.1.0 support
- HDP 6.1 support
- SMUIO 14.0 support
- PSP 14.0 support
- IH 6.1 support
- Lots of checkpatch cleanups
- GFX 9.4.3 updates
- Add USB PD and IFWI flashing documentation
- GPUVM updates
- RAS fixes
- DRR fixes
- FAMS fixes
- Virtual display fixes
- Soft IH fixes
- SMU13 fixes
- Rework PSP firmware loading for other IPs
- Kernel doc fixes
- DCN 3.0.1 fixes
- LTTPR fixes
- DP MST fixes
- DCN 3.1.6 fixes
- SMU 13.x fixes
- PSP 13.x fixes
- SubVP fixes
- GC 9.4.3 fixes
- Display bandwidth calculation fixes
- VCN4 secure submission fixes
- Allow building DC on RISC-V
- Add visible FB info to bo_print_info
- HBR3 fixes
- GFX9 MCBP fix
- GMC10 vmhub index fix
- GMC11 vmhub index fix
- Create a new doorbell manager
- SR-IOV fixes
- initial freesync panel replay support
- revert zpos properly until igt regression is fixeed
- use TTM to manage doorbell BAR
- Expose both current and average power via hwmon if supported
amdkfd:
- Cleanup CRIU dma-buf handling
- Use KIQ to unmap HIQ
- GFX 9.4.3 debugger updates
- GFX 9.4.2 debugger fixes
- Enable cooperative groups fof gfx11
- SVM fixes
- Convert older APUs to use dGPU path like newer APUs
- Drop IOMMUv2 path as it is no longer used
- TBA fix for aldebaran
i915:
- ICL+ DSI modeset sequence
- HDCP improvements
- MTL display fixes and cleanups
- HSW/BDW PSR1 restored
- Init DDI ports in VBT order
- General display refactors
- Start using plane scale factor for relative data rate
- Use shmem for dpt objects
- Expose RPS thresholds in sysfs
- Apply GuC SLPC min frequency softlimit correctly
- Extend Wa_14015795083 to TGL, RKL, DG1 and ADL
- Fix a VMA UAF for multi-gt platform
- Do not use stolen on MTL due to HW bug
- Check HuC and GuC version compatibility on MTL
- avoid infinite GPU waits due to premature release
of request memory
- Fixes and updates for GSC memory allocation
- Display SDVO fixes
- Take stolen handling out of FBC code
- Make i915_coherent_map_type GT-centric
- Simplify shmem_create_from_object map_type
msm:
- SM6125 MDSS support
- DPU: SM6125 DPU support
- DSI: runtime PM support, burst mode support
- DSI PHY: SM6125 support in 14nm DSI PHY driver
- GPU: prepare for a7xx
- fix a690 firmware
- disable relocs on a6xx and newer
radeon:
- Lots of checkpatch cleanups
ast:
- improve device-model detection
- Represent BMV as virtual connector
- Report DP connection status
nouveau:
- add new exec/bind interface to support Vulkan
- document some getparam ioctls
- improve VRAM detection
- various fixes/cleanups
- workraound DPCD issues
ivpu:
- MMU updates
- debugfs support
- Support vpu4
virtio:
- add sync object support
atmel-hlcdc:
- Support inverted pixclock polarity
etnaviv:
- runtime PM cleanups
- hang handling fixes
exynos:
- use fbdev DMA helpers
- fix possible NULL ptr dereference
komeda:
- always attach encoder
omapdrm:
- use fbdev DMA helpers
ingenic:
- kconfig regmap fixes
loongson:
- support display controller
mediatek:
- Small mtk-dpi cleanups
- DisplayPort: support eDP and aux-bus
- Fix coverity issues
- Fix potential memory leak if vmap() fail
mgag200:
- minor fixes
mxsfb:
- support disabling overlay planes
panfrost:
- fix sync in IRQ handling
ssd130x:
- Support per-controller default resolution plus DT bindings
- Reduce memory-allocation overhead
- Improve intermediate buffer size computation
- Fix allocation of temporary buffers
- Fix pitch computation
- Fix shadow plane allocation
tegra:
- use fbdev DMA helpers
- Convert to devm_platform_ioremap_resource()
- support bridge/connector
- enable PM
tidss:
- Support TI AM625 plus DT bindings
- Implement new connector model plus driver updates
vkms:
- improve write back support
- docs fixes
- support gamma LUT
zynqmp-dpsub:
- misc fixes
-----BEGIN PGP SIGNATURE-----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=CwV9
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2023-08-30' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"The drm core grew a new generic gpu virtual address manager, and new
execution locking helpers. These are used by nouveau now to provide
uAPI support for the userspace Vulkan driver. AMD had a bunch of new
IP core support, loads of refactoring around fbdev, but mostly just
the usual amount of stuff across the board.
core:
- fix gfp flags in drmm_kmalloc
gpuva:
- add new generic GPU VA manager (for nouveau initially)
syncobj:
- add new DRM_IOCTL_SYNCOBJ_EVENTFD ioctl
dma-buf:
- acquire resv lock for mmap() in exporters
- support dma-buf self import automatically
- docs fixes
backlight:
- fix fbdev interactions
atomic:
- improve logging
prime:
- remove struct gem_prim_mmap plus driver updates
gem:
- drm_exec: add locking over multiple GEM objects
- fix lockdep checking
fbdev:
- make fbdev userspace interfaces optional
- use linux device instead of fbdev device
- use deferred i/o helper macros in various drivers
- Make FB core selectable without drivers
- Remove obsolete flags FBINFO_DEFAULT and FBINFO_FLAG_DEFAULT
- Add helper macros and Kconfig tokens for DMA-allocated framebuffer
ttm:
- support init_on_free
- swapout fixes
panel:
- panel-edp: Support AUO B116XAB01.4
- Support Visionox R66451 plus DT bindings
- ld9040:
- Backlight support
- magic improved
- Kconfig fix
- Convert to of_device_get_match_data()
- Fix Kconfig dependencies
- simple:
- Set bpc value to fix warning
- Set connector type for AUO T215HVN01
- Support Innolux G156HCE-L01 plus DT bindings
- ili9881: Support TDO TL050HDV35 LCD panel plus DT bindings
- startek: Support KD070FHFID015 MIPI-DSI panel plus DT bindings
- sitronix-st7789v:
- Support Inanbo T28CP45TN89 plus DT bindings
- Support EDT ET028013DMA plus DT bindings
- Various cleanups
- edp: Add timings for N140HCA-EAC
- Allow panels and touchscreens to power sequence together
- Fix Innolux G156HCE-L01 LVDS clock
bridge:
- debugfs for chains support
- dw-hdmi:
- Improve support for YUV420 bus format
- CEC suspend/resume
- update EDID on HDMI detect
- dw-mipi-dsi: Fix enable/disable of DSI controller
- lt9611uxc: Use MODULE_FIRMWARE()
- ps8640: Remove broken EDID code
- samsung-dsim: Fix command transfer
- tc358764:
- Handle HS/VS polarity
- Use BIT() macro
- Various cleanups
- adv7511: Fix low refresh rate
- anx7625:
- Switch to macros instead of hardcoded values
- locking fixes
- tc358767: fix hardware delays
- sitronix-st7789v:
- Support panel orientation
- Support rotation property
- Add support for Jasonic JT240MHQS-HWT-EK-E3 plus DT bindings
amdgpu:
- SDMA 6.1.0 support
- HDP 6.1 support
- SMUIO 14.0 support
- PSP 14.0 support
- IH 6.1 support
- Lots of checkpatch cleanups
- GFX 9.4.3 updates
- Add USB PD and IFWI flashing documentation
- GPUVM updates
- RAS fixes
- DRR fixes
- FAMS fixes
- Virtual display fixes
- Soft IH fixes
- SMU13 fixes
- Rework PSP firmware loading for other IPs
- Kernel doc fixes
- DCN 3.0.1 fixes
- LTTPR fixes
- DP MST fixes
- DCN 3.1.6 fixes
- SMU 13.x fixes
- PSP 13.x fixes
- SubVP fixes
- GC 9.4.3 fixes
- Display bandwidth calculation fixes
- VCN4 secure submission fixes
- Allow building DC on RISC-V
- Add visible FB info to bo_print_info
- HBR3 fixes
- GFX9 MCBP fix
- GMC10 vmhub index fix
- GMC11 vmhub index fix
- Create a new doorbell manager
- SR-IOV fixes
- initial freesync panel replay support
- revert zpos properly until igt regression is fixeed
- use TTM to manage doorbell BAR
- Expose both current and average power via hwmon if supported
amdkfd:
- Cleanup CRIU dma-buf handling
- Use KIQ to unmap HIQ
- GFX 9.4.3 debugger updates
- GFX 9.4.2 debugger fixes
- Enable cooperative groups fof gfx11
- SVM fixes
- Convert older APUs to use dGPU path like newer APUs
- Drop IOMMUv2 path as it is no longer used
- TBA fix for aldebaran
i915:
- ICL+ DSI modeset sequence
- HDCP improvements
- MTL display fixes and cleanups
- HSW/BDW PSR1 restored
- Init DDI ports in VBT order
- General display refactors
- Start using plane scale factor for relative data rate
- Use shmem for dpt objects
- Expose RPS thresholds in sysfs
- Apply GuC SLPC min frequency softlimit correctly
- Extend Wa_14015795083 to TGL, RKL, DG1 and ADL
- Fix a VMA UAF for multi-gt platform
- Do not use stolen on MTL due to HW bug
- Check HuC and GuC version compatibility on MTL
- avoid infinite GPU waits due to premature release of request memory
- Fixes and updates for GSC memory allocation
- Display SDVO fixes
- Take stolen handling out of FBC code
- Make i915_coherent_map_type GT-centric
- Simplify shmem_create_from_object map_type
msm:
- SM6125 MDSS support
- DPU: SM6125 DPU support
- DSI: runtime PM support, burst mode support
- DSI PHY: SM6125 support in 14nm DSI PHY driver
- GPU: prepare for a7xx
- fix a690 firmware
- disable relocs on a6xx and newer
radeon:
- Lots of checkpatch cleanups
ast:
- improve device-model detection
- Represent BMV as virtual connector
- Report DP connection status
nouveau:
- add new exec/bind interface to support Vulkan
- document some getparam ioctls
- improve VRAM detection
- various fixes/cleanups
- workraound DPCD issues
ivpu:
- MMU updates
- debugfs support
- Support vpu4
virtio:
- add sync object support
atmel-hlcdc:
- Support inverted pixclock polarity
etnaviv:
- runtime PM cleanups
- hang handling fixes
exynos:
- use fbdev DMA helpers
- fix possible NULL ptr dereference
komeda:
- always attach encoder
omapdrm:
- use fbdev DMA helpers
ingenic:
- kconfig regmap fixes
loongson:
- support display controller
mediatek:
- Small mtk-dpi cleanups
- DisplayPort: support eDP and aux-bus
- Fix coverity issues
- Fix potential memory leak if vmap() fail
mgag200:
- minor fixes
mxsfb:
- support disabling overlay planes
panfrost:
- fix sync in IRQ handling
ssd130x:
- Support per-controller default resolution plus DT bindings
- Reduce memory-allocation overhead
- Improve intermediate buffer size computation
- Fix allocation of temporary buffers
- Fix pitch computation
- Fix shadow plane allocation
tegra:
- use fbdev DMA helpers
- Convert to devm_platform_ioremap_resource()
- support bridge/connector
- enable PM
tidss:
- Support TI AM625 plus DT bindings
- Implement new connector model plus driver updates
vkms:
- improve write back support
- docs fixes
- support gamma LUT
zynqmp-dpsub:
- misc fixes"
* tag 'drm-next-2023-08-30' of git://anongit.freedesktop.org/drm/drm: (1327 commits)
drm/gpuva_mgr: remove unused prev pointer in __drm_gpuva_sm_map()
drm/tests/drm_kunit_helpers: Place correct function name in the comment header
drm/nouveau: uapi: don't pass NO_PREFETCH flag implicitly
drm/nouveau: uvmm: fix unset region pointer on remap
drm/nouveau: sched: avoid job races between entities
drm/i915: Fix HPD polling, reenabling the output poll work as needed
drm: Add an HPD poll helper to reschedule the poll work
drm/i915: Fix TLB-Invalidation seqno store
drm/ttm/tests: Fix type conversion in ttm_pool_test
drm/msm/a6xx: Bail out early if setting GPU OOB fails
drm/msm/a6xx: Move LLC accessors to the common header
drm/msm/a6xx: Introduce a6xx_llc_read
drm/ttm/tests: Require MMU when testing
drm/panel: simple: Fix Innolux G156HCE-L01 LVDS clock
Revert "Revert "drm/amdgpu/display: change pipe policy for DCN 2.0""
drm/amdgpu: Add memory vendor information
drm/amd: flush any delayed gfxoff on suspend entry
drm/amdgpu: skip fence GFX interrupts disable/enable for S0ix
drm/amdgpu: Remove gfxoff check in GFX v9.4.3
drm/amd/pm: Update pci link speed for smu v13.0.6
...
Patch series "New page table range API", v6.
This patchset changes the API used by the MM to set up page table entries.
The four APIs are:
set_ptes(mm, addr, ptep, pte, nr)
update_mmu_cache_range(vma, addr, ptep, nr)
flush_dcache_folio(folio)
flush_icache_pages(vma, page, nr)
flush_dcache_folio() isn't technically new, but no architecture
implemented it, so I've done that for them. The old APIs remain around
but are mostly implemented by calling the new interfaces.
The new APIs are based around setting up N page table entries at once.
The N entries belong to the same PMD, the same folio and the same VMA, so
ptep++ is a legitimate operation, and locking is taken care of for you.
Some architectures can do a better job of it than just a loop, but I have
hesitated to make too deep a change to architectures I don't understand
well.
One thing I have changed in every architecture is that PG_arch_1 is now a
per-folio bit instead of a per-page bit when used for dcache clean/dirty
tracking. This was something that would have to happen eventually, and it
makes sense to do it now rather than iterate over every page involved in a
cache flush and figure out if it needs to happen.
The point of all this is better performance, and Fengwei Yin has measured
improvement on x86. I suspect you'll see improvement on your architecture
too. Try the new will-it-scale test mentioned here:
https://lore.kernel.org/linux-mm/20230206140639.538867-5-fengwei.yin@intel.com/
You'll need to run it on an XFS filesystem and have
CONFIG_TRANSPARENT_HUGEPAGE set.
This patchset is the basis for much of the anonymous large folio work
being done by Ryan, so it's received quite a lot of testing over the last
few months.
This patch (of 38):
Determine if a value lies within a range more efficiently (subtraction +
comparison vs two comparisons and an AND). It also has useful (under some
circumstances) behaviour if the range exceeds the maximum value of the
type. Convert all the conflicting definitions of in_range() within the
kernel; some can use the generic definition while others need their own
definition.
Link: https://lkml.kernel.org/r/20230802151406.3735276-1-willy@infradead.org
Link: https://lkml.kernel.org/r/20230802151406.3735276-2-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Updates for v6.6, which includes a backmerge of msm-fixes to avoid conficts.
Core:
- SM6125 MDSS support
DPU:
- SM6125 DPU support
- Added subblocks to display snapshot
- Use UBWC data from MDSS driver rather than duplicating it
- dpu_core_perf cleanup
DSI:
- Enabled burst mode to fix CMD mode panels
- Runtime PM support
- refgen regulator support
DSI PHY:
- SM6125 support in 14nm DSI PHY driver
GPU:
- Rework GPU identification to prepare for a7xx, and other a7xx prep
- Cleanups and fixes
- Disallow legacy relocs on a6xx and newer
- a690: switch to using a660_gmu.bin fw as this is what we have in
linux-firmware and we see no evidence that it should be different
from other a660 family (a6xx subgen 4) devices
- Submit overhead opts, 1.6x faster for NO_IMPLICIT_SYNC commits with
100 BOs to 2.5x faster for 1000 BOs
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGv_01g-edjdfKLWWcb-rO5aSyLsv5FpbKrTkXVL9+ngTQ@mail.gmail.com
Change the order of region allocations to make the addresses match
downstream. This shouldn't matter very much, but helps eliminate one
more difference when comparing register accesses.
Also, make the log region 16K long. That's what it is, unconditionally
on A6xx and A7xx.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/543338/
Signed-off-by: Rob Clark <robdclark@chromium.org>
The GMU force shutdown sequence involves some additional register cleanup
which was not implemented previously. Do so.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/543340/
Signed-off-by: Rob Clark <robdclark@chromium.org>
While it's not very well understood, there is some sort of a fault
handler implemented in the GMU firmware which triggers when a certain
bit is set, resulting in the M3 core not booting up the way we expect
it to.
Write a magic value to a magic register to hopefully prevent that
from happening.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/543335/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Since the revision becomes an opaque identifier with future GPUs, move
away from treating different ranges of bits as having a given meaning.
This means that we need to explicitly list different patch revisions in
the device table.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/549782/
All of these are derivatives of a630.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/549770/
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714174545.4056287-1-robh@kernel.org
Some (particularly SMD_RPM, a.k.a non-RPMh) SoCs implement A6XX GPUs
but don't implement the associated GMUs. This is due to the fact that
the GMU directly pokes at RPMh. Sadly, this means we have to take care
of enabling & scaling power rails, clocks and bandwidth ourselves.
Reuse existing Adreno-common code and modify the deeply-GMU-infused
A6XX code to facilitate these GPUs. This involves if-ing out lots
of GMU callbacks and introducing a new type of GMU - GMU wrapper (it's
the actual name that Qualcomm uses in their downstream kernels).
This is essentially a register region which is convenient to model
as a device. We'll use it for managing the GDSCs. The register
layout matches the actual GMU_CX/GX regions on the "real GMU" devices
and lets us reuse quite a bit of gmu_read/write/rmw calls.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542766/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Since the introduction of A6xx support, we've been enabling the CX GMU
power counter 0 in a bit of a weird spot. Move it to hw_init so that
GMU wrapper GPUs can reuse the same code paths. As a bonus, this order
makes it easier to compare mainline and downstream register access traces.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542765/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Introduce a6xx_gpu_sw_reset() in preparation for adding GMU wrapper
GPUs and reuse it in a6xx_gmu_force_off().
This helper, contrary to the original usage in GMU code paths, adds
a readback+delay sequence to ensure that the reset is never deasserted
too quickly due to e.g. OoO execution going crazy.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542758/
Signed-off-by: Rob Clark <robdclark@chromium.org>
This function is responsible for telling the GPU to halt transactions
on all of its relevant buses, drain them and leave them in a predictable
state, so that the GPU can be e.g. reset cleanly.
Move the function to a6xx_gpu.c, remove the static keyword and add a
prototype in a6xx_gpu.h to accomodate for the move.
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542762/
Signed-off-by: Rob Clark <robdclark@chromium.org>
As pointed out by Akhil during the review process of GMU wrapper
introduction [1], it makes sense to move this write into the function
that's responsible for forcibly shutting the GMU off.
It is also very convenient to move this to GMU-specific code, so that
it does not have to be guarded by an if-condition to avoid calling it
on GMU wrapper targets.
Move the write to the aforementioned a6xx_gmu_force_off() to achieve
that. No effective functional change.
[1] https://lore.kernel.org/linux-arm-msm/20230501194022.GA18382@akhilpo-linux.qualcomm.com/
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542752/
Signed-off-by: Rob Clark <robdclark@chromium.org>
These two will be reused by at least A619_holi in the non-gmu
paths. Turn them non-static them to make it possible.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542751/
Signed-off-by: Rob Clark <robdclark@chromium.org>
As per the recommended recovery sequence of adreno gpu, cx gdsc should
collapse at hardware before it is turned back ON. This helps to clear
out the stale states in hardware before it is reinitialized. Use the
genpd notifier along with the newly introduced
dev_pm_genpd_synced_poweroff() api to ensure that cx gdsc has collapsed
before we turn it back ON.
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/516472/
Link: https://lore.kernel.org/r/20230102161757.v5.5.I9e10545c6a448d5eb1b734839b871d1b3146dac3@changeid
Signed-off-by: Rob Clark <robdclark@chromium.org>
When a device has multiple power domains, dev->power_domain is left
empty during probe. That didn't cause any issue so far because we are
freeloading on smmu driver's vote on cx gdsc. Instead of that, create
a device_link between cx genpd device and gmu device to keep a vote from
gpu driver.
Before this patch:
localhost ~ # cat /sys/kernel/debug/pm_genpd/pm_genpd_summary
gx_gdsc on 0
/devices/genpd:1:3d6a000.gmu active 0
cx_gdsc on 0
/devices/platform/soc@0/3da0000.iommu active 0
After this patch:
localhost ~ # cat /sys/kernel/debug/pm_genpd/pm_genpd_summary
gx_gdsc on 0
/devices/genpd:1:3d6a000.gmu active 0
cx_gdsc on 0
/devices/platform/soc@0/3da0000.iommu active 0
/devices/genpd:0:3d6a000.gmu active 0
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/516468/
Link: https://lore.kernel.org/r/20230102161757.v5.3.I7f545d8494dcdbe6e96a15fbe8aaf5bb0c003d50@changeid
Signed-off-by: Rob Clark <robdclark@chromium.org>
If, for whatever reason, we're trying process adreno_runtime_resume()
at the same time that a6xx_destroy() is running then things can go
boom. Specifically adreno_runtime_resume() will eventually call
a6xx_pm_resume() and that may try to resume the gmu.
Let's grab the GMU lock as we're destroying the GMU. That will solve
the race because a6xx_pm_resume() grabs the same lock. That makes the
access of `gmu->initialized` in a6xx_gmu_resume() safe.
We'll also return an error code in a6xx_gmu_resume() if we see that
`gmu->initialized` was false. If this happens we'll bail out of the
rest of a6xx_pm_resume(), which is good because the rest of that
function is also not good to do if we're racing with a6xx_destroy().
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/521232/
Link: https://lore.kernel.org/r/20230202104822.1.I0e49003bf4dd1dead9be4a29dbee41f3b1236e48@changeid
Signed-off-by: Rob Clark <robdclark@chromium.org>
After the msm_iommu instance is created, the IOMMU domain is completely
handled inside the msm_iommu code. Move the iommu_domain_alloc() call
into the msm_iommu_new() to simplify callers code.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/509615/
Link: https://lore.kernel.org/r/20221102175449.452283-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
From testing on sc7180-trogdor devices, reading the GMU registers
needs the GMU clocks to be enabled. Those clocks get turned on in
a6xx_gmu_resume(). Confusingly enough, that function is called as a
result of the runtime_pm of the GPU "struct device", not the GMU
"struct device". Unfortunately the current a6xx_gpu_busy() grabs a
reference to the GMU's "struct device".
The fact that we were grabbing the wrong reference was easily seen to
cause crashes that happen if we change the GPU's pm_runtime usage to
not use autosuspend. It's also believed to cause some long tail GPU
crashes even with autosuspend.
We could look at changing it so that we do pm_runtime_get_if_in_use()
on the GPU's "struct device", but then we run into a different
problem. pm_runtime_get_if_in_use() will return 0 for the GPU's
"struct device" the whole time when we're in the "autosuspend
delay". That is, when we drop the last reference to the GPU but we're
waiting a period before actually suspending then we'll think the GPU
is off. One reason that's bad is that if the GPU didn't actually turn
off then the cycle counter doesn't lose state and that throws off all
of our calculations.
Let's change the code to keep track of the suspend state of
devfreq. msm_devfreq_suspend() is always called before we actually
suspend the GPU and msm_devfreq_resume() after we resume it. This
means we can use the suspended state to know if we're powered or not.
NOTE: one might wonder when exactly our status function is called when
devfreq is supposed to be disabled. The stack crawl I captured was:
msm_devfreq_get_dev_status
devfreq_simple_ondemand_func
devfreq_update_target
qos_notifier_call
qos_max_notifier_call
blocking_notifier_call_chain
pm_qos_update_target
freq_qos_apply
apply_constraint
__dev_pm_qos_update_request
dev_pm_qos_update_request
msm_devfreq_idle_work
Fixes: eadf79286a ("drm/msm: Check for powered down HW in the devfreq callbacks")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/489124/
Link: https://lore.kernel.org/r/20220610124639.v4.1.Ie846c5352bc307ee4248d7cab998ab3016b85d06@changeid
Signed-off-by: Rob Clark <robdclark@chromium.org>
Get rid of all the unnecessary conversion between address/size and page
offsets. It just confuses things.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220411215849.297838-6-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
If you don't realize is_a650_family() also encompasses a660 family,
you'd think that the debug buffer is double allocated. Add a comment
to make this more clear.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20211124214151.1427022-11-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
There are two problems here:
1) The "seqptr" is used uninitalized when we free it at the end.
2) The a6xx_gmu_get_mmio() function returns error pointers. It never
returns true.
Fixes: 64245fc551 ("drm/msm/a6xx: use AOP-initialized PDC for a650")
Fixes: f8fc924e08 ("drm/msm/a6xx: Fix PDC register overlap")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211004134530.GB11689@kili
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
dev_pm_opp_find_freq_exact never return null but ERR_PTR(),so we
should use IS_ERR() to clarify and avoid compilation warnings.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Link: https://lore.kernel.org/r/1604630714-6163-1-git-send-email-wangqing@vivo.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
I've seen some crashes in our crash reporting that *look* like multiple
threads stomping on each other while communicating with GMU. So wrap
all those paths in a lock.
Signed-off-by: Rob Clark <robdclark@chromium.org>
This patch adds support for the gpu found in the Snapdragon 7c Gen 3
compute platform. This gpu is similar to the exisiting a660 gpu with
minor delta in the programing sequence. As the Adreno GPUs are moving
away from a numeric chipid based naming scheme to a string, it was
decided to use 0x06030500 as the chip id of this gpu to communicate
to the userspace driver.
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Link: https://lore.kernel.org/r/20210730011945.v4.3.I610377db0934b6b7deda532ec2bf786a02c38c01@changeid
Signed-off-by: Rob Clark <robdclark@chromium.org>
No idea why we were still using this. It certainly hasn't been needed
for some time. So drop the pointless twin codepaths.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-4-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add adreno_is_{a660,a650_family} helpers and convert update existing
adreno_is_a650 usage based on downstream driver's logic (changing into
adreno_is_a650_family or adding adreno_is_a660).
And add the remaining changes required for A660, again based on
the downstream driver: missing GMU allocations, additional register init,
dummy hfi BW table, cp protect list, entry in gpulist table, hwcg table,
updated a6xx_ucode_check_version check.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20210608172808.11803-6-jonathan@marek.ca
Signed-off-by: Rob Clark <robdclark@chromium.org>
SM8250 AOP firmware already sets up PDC registers for us, and it only needs
to be enabled. This path will be used for other newer GPUs.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20210608172808.11803-3-jonathan@marek.ca
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use resource-managed OPP API to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314163408.22292-12-digetx@gmail.com
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
