The Powkiddy RGB10MAX3 is a handheld device with a 5 inch 720x1280
display panel with a Sitronix ST7703 display controller. The panel
is installed rotated 270 degrees.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240212184950.52210-3-macroalpha82@gmail.com
Fix flickering of the pinephone's XDB599 panel that happens after
resume.
Extend the delay after issuing the command to exit sleep mode from 60 to
120 msec as per the controller's specification.
Introduce a 120 msec delay after issuing the command to enter sleep
mode. This is needed in order for the controller to reliably finalize
the sleep in sequence before switching of power supply.
In contrast to the JH057N panel, the XBD599 panel does not require a 20
msec delay after initialization and exiting sleep mode. Therefore, move
the delay into the already existing device specific initialization
function.
The XDB599 does not require a 20 msec delay between the SETBGP and
SETVCOM commands. Therefore, remove the delay from the device specific
initialization function.
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Cc: Ondrej Jirman <megi@xff.cz>
Reported-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213123238.76889-2-frank@oltmanns.dev
Switching to a different reset sequence, enabling IOVCC before enabling
VCC.
There also needs to be a delay after enabling the supplies and before
deasserting the reset. The datasheet specifies 1ms after the supplies
reach the required voltage. Use 10-20ms to also give the power supplies
some time to reach the required voltage, too.
This fixes intermittent panel initialization failures and screen
corruption during resume from sleep on panel xingbangda,xbd599 (e.g.
used in PinePhone).
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Reported-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230211171748.36692-2-frank@oltmanns.dev
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714174545.4056287-1-robh@kernel.org
The Anbernic RG353V-V2 is a 5 inch panel used in a new revision of the
Anbernic RG353V handheld gaming device. Add support for it.
Unfortunately it appears this controller is not able to support 120hz
or 100hz mode like the first revision panel.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230426143213.4178586-4-macroalpha82@gmail.com
There are macros for these already in the <drm/drm_mipi_dsi.h> header, use
that instead and delete the custom DSI write macros defined in the driver.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230107191822.3787147-3-javierm@redhat.com
All implementations return 0 and the return value of mipi_dsi_drv_remove()
is ignored anyhow.
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220708094922.1408248-4-u.kleine-koenig@pengutronix.de
This eliminates the following sparse warning:
drivers/gpu/drm/panel/panel-sitronix-st7703.c:156:26: warning: symbol
'jh057n00900_panel_desc' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
[Use static const]
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200912033809.142773-1-yanaijie@huawei.com
Standardize on the dev_ based logging and drop the include of drm_print.h.
Fix a few cases where "x@" was used when printing the mode.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Guido Günther <agx@sigxcpu.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200815125406.1153224-5-sam@ravnborg.org
The reset pin is inverted, so if we don't assert reset, the actual gpio
will be high and may keep driving the IO port of the panel.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701162928.1638874-12-megous@megous.com
The datasheet suggests to issue sleep in after display off
as a part of the panel's shutdown sequence.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701162928.1638874-11-megous@megous.com
Xingbangda XBD599 is a 5.99" 720x1440 MIPI-DSI LCD panel used in
PinePhone. Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701162928.1638874-10-megous@megous.com
Calling sleep out and display on is a controller specific part
of the initialization process. Move it out of the panel specific
initialization function to the enable callback.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701162928.1638874-9-megous@megous.com
It's better than having it spread around the driver.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701162928.1638874-8-megous@megous.com
Parametrize the driver so that it can support more panels based
on st7703 controller.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701162928.1638874-7-megous@megous.com
This is done so that code that's not specific to a particular
jh057n panel is named after the controller. Functions specific
to the panel are kept named after the panel.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701162928.1638874-6-megous@megous.com
This rename is done so that the driver matches the name of the
display controller and in preparation for adding support for more
panels to the driver.
This is just a basic file rename, with no code changes.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701162928.1638874-5-megous@megous.com
2020-07-01 19:22:49 +02:00
Renamed from drivers/gpu/drm/panel/panel-rocktech-jh057n00900.c (Browse further)
