The check in nand_base.c, nand_scan_tail() : has the following code:
(ecc->steps * ecc->size != mtd->writesize) which fails for some NAND chips.
Remove ECC entries in this driver which are not integral multiplications,
and adjust the number of chunks for entries which fails the above
calculation so it will calculate correctly (this was previously done
automatically before the check and was removed in a later commit).
Fixes: 68c18dae68 ("mtd: rawnand: marvell: add missing layouts")
Cc: stable@vger.kernel.org
Signed-off-by: Elad Nachman <enachman@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
remove callbacks to return void. Comes next (in number of changes) Kees'
additional structures annotations to improve the sanitizers. The usual
amount of cleanups apply.
About the more substancial contribution, one main function of the
partitions core could return an error which was not checked, this is now
fixed. On the bindings side, fixed partitions can now have a compression
property. Finally, an erroneous situation is now always avoided in the
MAP RAM driver.
* CFI
A several years old byte swap has been fixed.
* NAND
The subsystem has, as usual, seen a bit of cleanup being done this
cycle, typically return values of platform_get_irq() and
devm_kasprintf(). There is also a better ECC check in the Arasan
driver. This comes with smaller misc changes.
In the SPI-NAND world there is now support for Foresee F35SQA002G,
Winbond W25N and XTX XT26 chips.
* SPI NOR
For SPI NOR we cleaned the flash info entries in order to have
them slimmer and self explanatory. In order to make the entries
as slim as possible, we introduced sane default values so that
the actual flash entries don't need to specify them. We now use
a flexible macro to specify the flash ID instead of the previous
INFOx() macros that had hardcoded ID lengths.
Instead of:
- { "w25q512nwm", INFO(0xef8020, 0, 64 * 1024, 0)
- OTP_INFO(256, 3, 0x1000, 0x1000) },
We now use:
+ .id = SNOR_ID(0xef, 0x80, 0x20),
+ .name = "w25q512nwm",
+ .otp = SNOR_OTP(256, 3, 0x1000, 0x1000),
We also removed some flash entries: the very old Catalyst
SPI EEPROMs that were introduced once with the SPI-NOR subsystem,
and a Fujitsu MRAM. Both should use the at25 EEPROM driver.
The latter even has device tree bindings for the at25 driver.
We made sure that the conversion didn't introduce any unwanted
changes by comparing the .rodata segment before and after the
conversion. The patches landed in linux-next immediately after
v6.6-rc2, we haven't seen any regressions yet.
Apart of the autumn cleaning we introduced a new flash entry,
at25ff321a, and added block protection support for mt25qu512a.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmVGJNgACgkQJWrqGEe9
VoQ5ggf/flUHU7RI02T7HNwkHayq/NOgaGIUkUZEwdfEBd6/8nLzpDeh9UuQCBvO
izOdRSiDDhcav6YsKs+7UKnonY0uZ5VwB3cjRcgWzsI/nyARs5CeV8VJxqxiGYqU
25rZVVVoNr/4eV6kb9Sx0yUTLobidlNKtpv0w0hLFoVu+eb35RzE/MHaYmialM87
W4W/aHxJH/Nsz9hi13FWE4CpbRYbg2hEBsQhaQV/Uvf4htxYZ+H0ItZGMm/Lsjk4
31eCbgH4yOP2DaQi5KRtvZauKMptqWOo+3ymjDGDi7soQe2qRa5BFsH8cz9/2lDk
hxLk/mGKB4jfnkAaOv5dc0CTcYsnuQ==
=V+qH
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"The main set of changes is related to Uwe's work converting platform
remove callbacks to return void. Comes next (in number of changes)
Kees' additional structures annotations to improve the sanitizers. The
usual amount of cleanups apply.
About the more substancial contribution, one main function of the
partitions core could return an error which was not checked, this is
now fixed. On the bindings side, fixed partitions can now have a
compression property. Finally, an erroneous situation is now always
avoided in the MAP RAM driver.
CFI:
- A several years old byte swap has been fixed.
NAND:
- The subsystem has, as usual, seen a bit of cleanup being done this
cycle, typically return values of platform_get_irq() and
devm_kasprintf(). There is also a better ECC check in the Arasan
driver. This comes with smaller misc changes.
- In the SPI-NAND world there is now support for Foresee F35SQA002G,
Winbond W25N and XTX XT26 chips.
SPI NOR:
- For SPI NOR we cleaned the flash info entries in order to have them
slimmer and self explanatory. In order to make the entries as slim
as possible, we introduced sane default values so that the actual
flash entries don't need to specify them. We now use a flexible
macro to specify the flash ID instead of the previous INFOx()
macros that had hardcoded ID lengths.
Instead of:
{ "w25q512nwm", INFO(0xef8020, 0, 64 * 1024, 0)
OTP_INFO(256, 3, 0x1000, 0x1000) },
We now use:
.id = SNOR_ID(0xef, 0x80, 0x20),
.name = "w25q512nwm",
.otp = SNOR_OTP(256, 3, 0x1000, 0x1000),
- We also removed some flash entries: the very old Catalyst SPI
EEPROMs that were introduced once with the SPI-NOR subsystem, and a
Fujitsu MRAM. Both should use the at25 EEPROM driver. The latter
even has device tree bindings for the at25 driver.
- We made sure that the conversion didn't introduce any unwanted
changes by comparing the .rodata segment before and after the
conversion. The patches landed in linux-next immediately after
v6.6-rc2, we haven't seen any regressions yet.
- Apart of the autumn cleaning we introduced a new flash entry,
at25ff321a, and added block protection support for mt25qu512a"
* tag 'mtd/for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (91 commits)
mtd: cfi_cmdset_0001: Byte swap OTP info
mtd: rawnand: meson: check return value of devm_kasprintf()
mtd: rawnand: intel: check return value of devm_kasprintf()
mtd: rawnand: sh_flctl: Convert to module_platform_driver()
mtd: spi-nor: micron-st: use SFDP table for mt25qu512a
mtd: spi-nor: micron-st: enable lock/unlock for mt25qu512a
mtd: rawnand: Remove unused of_gpio.h inclusion
mtd: spinand: Add support for XTX XT26xxxDxxxxx
mtd: spinand: winbond: add support for serial NAND flash
mtd: rawnand: cadence: Annotate struct cdns_nand_chip with __counted_by
mtd: rawnand: Annotate struct mtk_nfc_nand_chip with __counted_by
mtd: spinand: add support for FORESEE F35SQA002G
mtd: rawnand: rockchip: Use struct_size()
mtd: rawnand: arasan: Include ECC syndrome along with in-band data while checking for ECC failure
mtd: Use device_get_match_data()
mtd: spi-nor: nxp-spifi: Convert to platform remove callback returning void
mtd: spi-nor: hisi-sfc: Convert to platform remove callback returning void
mtd: maps: sun_uflash: Convert to platform remove callback returning void
mtd: maps: sa1100-flash: Convert to platform remove callback returning void
mtd: maps: pxa2xx-flash: Convert to platform remove callback returning void
...
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct marvell_nand_chip.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230915201243.never.235-kees@kernel.org
The NAND core complies with the ONFI specification, which itself
mentions that after any program or erase operation, a status check
should be performed to see whether the operation was finished *and*
successful.
The NAND core offers helpers to finish a page write (sending the
"PAGE PROG" command, waiting for the NAND chip to be ready again, and
checking the operation status). But in some cases, advanced controller
drivers might want to optimize this and craft their own page write
helper to leverage additional hardware capabilities, thus not always
using the core facilities.
Some drivers, like this one, do not use the core helper to finish a page
write because the final cycles are automatically managed by the
hardware. In this case, the additional care must be taken to manually
perform the final status check.
Let's read the NAND chip status at the end of the page write helper and
return -EIO upon error.
Cc: stable@vger.kernel.org
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Reported-by: Aviram Dali <aviramd@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Ravi Chandra Minnikanti <rminnikanti@marvell.com>
Link: https://lore.kernel.org/linux-mtd/20230717194221.229778-1-miquel.raynal@bootlin.com
* Fix -Wvoid-pointer-to-enum-cast warning
* Export 'nand_exit_status_op()'
* dt-bindings: Fix nand-controller.yaml license
Raw NAND controller driver changes:
* Omap, Omap2, Samsung, Atmel, fsl_upm, lpc32xx_slc, lpc32xx_mlc, STM32_FMC2,
sh_ftlctl, MXC, Sunxi:
- Use devm_platform_get_and_ioremap_resource()
* Orion, vf610_nfc, Sunxi, STM32_FMC2, MTK, mpc5121, lpc32xx_slc, Intel,
FSMC, Arasan:
- Use helper function devm_clk_get_optional_enabled()
* Brcmnand:
- Use devm_platform_ioremap_resource_byname()
- Propagate init error -EPROBE_DEFER up
- Propagate error and simplify ternary operators
- Fix mtd oobsize
- Fix potential out-of-bounds access in oob write
- Fix crash during the panic_write
- Fix potential false time out warning
- Fix ECC level field setting for v7.2 controller
* fsmc: Handle clk prepare error in fsmc_nand_resume()
* Marvell: Add support for AC5 SoC
* Meson:
- Support for 512B ECC step size
- Fix build error
- Use NAND core API to check status
- dt-bindings:
* Make ECC properties dependent
* Support for 512B ECC step size
* Drop unneeded quotes
* Oxnas: Remove driver and bindings
* Qcom:
- Conversion to ->exec_op()
- Removal of the legacy interface
- Two full series of improvements/misc fixes
* Use the BIT() macro
* Use u8 instead of uint8_t
* Fix alignment with open parenthesis
* Fix the spacing
* Fix wrong indentation
* Fix a typo
* Early structure initialization
* Fix address parsing within ->exec_op()
* Remove superfluous initialization of "ret"
* Rename variables in qcom_op_cmd_mapping()
* Handle unsupported opcode in qcom_op_cmd_mapping()
* Fix the opcode check in qcom_check_op()
* Use EOPNOTSUPP instead of ENOTSUPP
* Wrap qcom_nand_exec_op() to 80 columns
* Unmap sg_list and free desc within submic_descs()
* Simplify the call to nand_prog_page_end_op()
* Do not override the error no of submit_descs()
* Sort includes alphabetically
* Clear buf_count and buf_start in raw read
* Add read/read_start ops in exec_op path
* vf610_nfc: Do not check 0 for platform_get_irq()
SPI-NAND changes:
* gigadevice: Add support for GD5F1GQ{4,5}RExxH
* esmt: Add support for F50D2G41KA
* toshiba: Add support for T{C,H}58NYG{0,2}S3HBAI4 and TH58NYG3S0HBAI6
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmTsYbAACgkQJWrqGEe9
VoQTsQf+MA+rMfIoyOSLwaFm0Z5UPwIuhleumNgkV2yoC2H42ugz7+Qo4ZS8iHjY
qBUWA/PF4s5snF8A/x4uSEUkdT6etuJ58uKy53304C6cx7RXLtfc7qJfs6fQVLqL
O6uO/EPdUkmiIbdXcRQRiAUDRHEFMPVEHd5pECB0l/qbiNLWQWRFUsmaP6kBZnm1
y7xPfxJo3GuMKJMWnMg+kcoQ7hhIvd0FRztL6VT4SV/et/nfCYjAVXOpViZ8e3+d
tq5yp+WatcBL9tGFSV3IyLW5Z+x1oVDoOIoTk/hWdHsITaHBxXBb8Llc6Eh7GYCD
5mj/renycHEv2Wc2v93z7W3XtnY77Q==
=Pp9B
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.6' into mtd/next
Raw NAND core changes:
* Fix -Wvoid-pointer-to-enum-cast warning
* Export 'nand_exit_status_op()'
* dt-bindings: Fix nand-controller.yaml license
Raw NAND controller driver changes:
* Omap, Omap2, Samsung, Atmel, fsl_upm, lpc32xx_slc, lpc32xx_mlc, STM32_FMC2,
sh_ftlctl, MXC, Sunxi:
- Use devm_platform_get_and_ioremap_resource()
* Orion, vf610_nfc, Sunxi, STM32_FMC2, MTK, mpc5121, lpc32xx_slc, Intel,
FSMC, Arasan:
- Use helper function devm_clk_get_optional_enabled()
* Brcmnand:
- Use devm_platform_ioremap_resource_byname()
- Propagate init error -EPROBE_DEFER up
- Propagate error and simplify ternary operators
- Fix mtd oobsize
- Fix potential out-of-bounds access in oob write
- Fix crash during the panic_write
- Fix potential false time out warning
- Fix ECC level field setting for v7.2 controller
* fsmc: Handle clk prepare error in fsmc_nand_resume()
* Marvell: Add support for AC5 SoC
* Meson:
- Support for 512B ECC step size
- Fix build error
- Use NAND core API to check status
- dt-bindings:
* Make ECC properties dependent
* Support for 512B ECC step size
* Drop unneeded quotes
* Oxnas: Remove driver and bindings
* Qcom:
- Conversion to ->exec_op()
- Removal of the legacy interface
- Two full series of improvements/misc fixes
* Use the BIT() macro
* Use u8 instead of uint8_t
* Fix alignment with open parenthesis
* Fix the spacing
* Fix wrong indentation
* Fix a typo
* Early structure initialization
* Fix address parsing within ->exec_op()
* Remove superfluous initialization of "ret"
* Rename variables in qcom_op_cmd_mapping()
* Handle unsupported opcode in qcom_op_cmd_mapping()
* Fix the opcode check in qcom_check_op()
* Use EOPNOTSUPP instead of ENOTSUPP
* Wrap qcom_nand_exec_op() to 80 columns
* Unmap sg_list and free desc within submic_descs()
* Simplify the call to nand_prog_page_end_op()
* Do not override the error no of submit_descs()
* Sort includes alphabetically
* Clear buf_count and buf_start in raw read
* Add read/read_start ops in exec_op path
* vf610_nfc: Do not check 0 for platform_get_irq()
SPI-NAND changes:
* gigadevice: Add support for GD5F1GQ{4,5}RExxH
* esmt: Add support for F50D2G41KA
* toshiba: Add support for T{C,H}58NYG{0,2}S3HBAI4 and TH58NYG3S0HBAI6
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it was merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230714174751.4060439-1-robh@kernel.org
Add support for the AC5/AC5X SoC from Marvell. The NFC on this SoC only
supports SDR modes up to 3.
Marvell's SDK includes some predefined values for the ndtr registers.
These haven't been incorporated as the existing code seems to get good
values based on measurements taken with an oscilloscope.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230703035044.2063303-4-chris.packham@alliedtelesis.co.nz
marvell_nfc_setup_interface() uses the frequency retrieved from the
clock associated with the nand interface to determine the timings that
will be used. By changing the NAND frequency select without reflecting
this in the clock configuration this means that the timings calculated
don't correctly meet the requirements of the NAND chip. This hasn't been
an issue up to now because of a different bug that was stopping the
timings being updated after they were initially set.
Fixes: b25251414f ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230525003154.2303012-2-chris.packham@alliedtelesis.co.nz
When new timing values are calculated in marvell_nfc_setup_interface()
ensure that they will be applied in marvell_nfc_select_target() by
clearing the selected_chip pointer.
Fixes: b25251414f ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230525003154.2303012-1-chris.packham@alliedtelesis.co.nz
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> # atmel
Reviewed-by: Paul Cercueil <paul@crapouillou.net> # ingenic
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> # ingenic
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # intel
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # meson
Acked-by: Roger Quadros <rogerq@kernel.org> # omap_elm
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> # renesas
Reviewed-by: Heiko Stuebner <heiko@sntech.de> # rockchip
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> # sunxi
Acked-by: Thierry Reding <treding@nvidia.com> # tegra
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230411113816.3472237-1-u.kleine-koenig@pengutronix.de
A missing layouts were added to the driver to support NAND flashes
with ECC layouts of 12 or 16 with page sized of 2048, 4096 or 8192.
Usually theses are rare layouts, but in Marvell AC5 driver, the ECC
level is set according to the spare area, so we may use these layouts
more frequently.
Signed-off-by: Aviram Dali <aviramd@marvell.com>
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221216162715.3230766-1-vadym.kochan@plvision.eu
* Drop obsolete dependencies on COMPILE_TEST
* MAINTAINERS: rectify entry for MESON NAND controller bindings
* Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
* marvell: Enable NFC/DEVBUS arbiter
* gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
* mpc5121: Replace NO_IRQ by 0
* lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
* lpc32xx_mlc: Switch to using pm_ptr()
* cadence: Support 64-bit slave dma interface
* rockchip: Describe rk3128-nfc in the bindings
* brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
* winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmOGGfIACgkQJWrqGEe9
VoSZVQgAmew5RtMegFus/AXflUsGYCvZKfV1LVnxmSoGIKBrJr3yjzh6mFuLyzaP
qt2KljEJ4dblk2M3efosX5YeAkz7A7evm218NHGeKWHMPCDimSE1ptAyBhhMmsVi
cgCgu3LXh369dK9OAm7ZVR4hOdDuK5rpYIcXA4mUh0yqiFxfxsuuNY7QBDVrN+qt
SNmZkTBbCgGRxo7RRanN2ljnSm31p6TyhngUDKG89puMka9gGA9yWLbWFDpwM5SS
L0Tr2ZOHctzz/X/1s2yPcnN6ZPpqsc1wLnGyLOWlhkm7oo7aiT59rlHj9GHbp82h
7lXf7MeWxSNSVr9PMHHUR7XDqlLaOw==
=aOZ+
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.2' into mtd/next
Raw NAND core changes:
* Drop obsolete dependencies on COMPILE_TEST
* MAINTAINERS: rectify entry for MESON NAND controller bindings
* Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
* marvell: Enable NFC/DEVBUS arbiter
* gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
* mpc5121: Replace NO_IRQ by 0
* lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
* lpc32xx_mlc: Switch to using pm_ptr()
* cadence: Support 64-bit slave dma interface
* rockchip: Describe rk3128-nfc in the bindings
* brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
* winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification
Fix merge conflict with mtd tree regarding the brcm bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The CN9130 SoC (an ARMADA 8K type) has both a NAND Flash Controller and
a generic local bus controller (Device Bus Controller) that share common
pins.
With a board design that incorporates both a NAND flash and uses
the Device Bus (in our case for an SRAM) accessing the Device Bus device
fails unless the NfArbiterEn bit is set. Setting the bit enables
arbitration between the Device Bus and the NAND flash.
Since there is no obvious downside in enabling this for designs that
don't require arbitration, we always enable it.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221109231325.7714-1-hamish.martin@alliedtelesis.co.nz
Originally the absence of the marvell,nand-keep-config property caused
the setup_data_interface function to be provided. However when
setup_data_interface was moved into nand_controller_ops the logic was
unintentionally inverted. Update the logic so that only if the
marvell,nand-keep-config property is present the bootloader NAND config
kept.
Cc: stable@vger.kernel.org
Fixes: 7a08dbaedd ("mtd: rawnand: Move ->setup_data_interface() to nand_controller_ops")
Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220927024728.28447-1-chris.packham@alliedtelesis.co.nz
Fix kerneldoc comments and add missing documentation for members to fix
W=1 compile warnings like:
drivers/mtd/nand/raw/marvell_nand.c:251: warning:
cannot understand function prototype: 'struct marvell_hw_ecc_layout '
drivers/mtd/nand/raw/marvell_nand.c:342: warning:
Function parameter or member 'layout' not described in 'marvell_nand_chip'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-5-krzk@kernel.org
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-4-krzk@kernel.org
Mechanical switch from the legacy "mode" enumeration to the new
"engine type" enumeration in drivers and board files.
The device tree parsing is also updated to return the new enumeration
from the old strings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-11-miquel.raynal@bootlin.com
The name/suffix data_interface is a bit misleading in that the field
or functions actually represent a configuration that can be applied by
the controller/chip. Let's rename all fields/functions/hooks that are
worth renaming.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
As a preparation for allocating the data interface structure
dynamically (and rename it), let's avoid accessing
chip->data_interface directly.
Instead, we introduce a helper, nand_get_interface_config(), and use
it to retrieve the current data interface configuration out of a
nand_chip object.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-19-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-26-miquel.raynal@bootlin.com
This can be used to discriminate between two path in the parameter
page detection: use data_in cycles (like before) if supported, use the
CHANGE READ COLUMN command otherwise.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-9-miquel.raynal@bootlin.com
There is no correction involved at this point, it is just a matter of
reading registers and checking whether bitflips have occurred or
not. Rename the function to clarify it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-7-miquel.raynal@bootlin.com
Do not call nand_release() while the MTD device has not been
registered, use nand_cleanup() instead.
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-4-miquel.raynal@bootlin.com
Switch from the old platform_get_resource()/devm_ioremap_resource()
couple to the newer devm_platform_ioremap_resource() helper.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-3-miquel.raynal@bootlin.com
In a previous fix, I changed the condition on which the timeout of an
IRQ is reached from:
if (!ret)
into:
if (ret && !pending)
While having a non-zero return code is usual in the Linux kernel, here
ret comes from a wait_for_completion_timeout() which returns 0 when
the waiting period is too long.
Hence, the revised condition should be:
if (!ret && !pending)
The faulty patch did not produce any error because of the !pending
condition so this change is finally purely cosmetic and does not
change the actual driver behavior.
Fixes: cafb56dd74 ("mtd: rawnand: marvell: prevent timeouts on a loaded machine")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-2-miquel.raynal@bootlin.com
->exec_op() is passed a check_only argument that encodes when the
controller should just check whether the operation is supported or not
without executing it. Some controllers simply ignore this arguments,
others don't but keep modifying some of the registers before returning.
Let's fix all those drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200418194217.1016060-1-boris.brezillon@collabora.com
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
Use using dma_request_chan() directly to return the real error code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-4-peter.ujfalusi@ti.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200226222722.GA18020@embeddedor
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
MTD core changes:
- New AFS partition parser
- Update MAINTAINERS entry
- Use of fall-throughs markers
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from generic
functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
* Switch to ->exec-op().
- meson:
* Misc cleanups and fixes.
* New OOB layout.
- Sunxi:
* A23/A33 NAND DMA support.
- Ingenic:
* Full reorganization and cleanup.
* Clear separation between NAND controller and ECC engine.
* Support JZ4740 an JZ4725B.
- Denali:
* Clear controller/chip separation.
* ->exec_op() migration.
* Various cleanups.
- fsl_elbc:
* Enable software ECC support.
- Atmel:
* Sam9x60 support.
- GPMI:
* Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
SPI NOR core changes:
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
* Avoid crossing 4K address boundary on read/write
* Add support for Intel Comet Lake SPI serial flash
-----BEGIN PGP SIGNATURE-----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=HXap
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- New AFS partition parser
- Update MAINTAINERS entry
- Use of fall-throughs markers
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from
generic functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
- Switch to ->exec-op().
- meson:
- Misc cleanups and fixes.
- New OOB layout.
- Sunxi:
- A23/A33 NAND DMA support.
- Ingenic:
- Full reorganization and cleanup.
- Clear separation between NAND controller and ECC engine.
- Support JZ4740 an JZ4725B.
- Denali:
- Clear controller/chip separation.
- ->exec_op() migration.
- Various cleanups.
- fsl_elbc:
- Enable software ECC support.
- Atmel:
- Sam9x60 support.
- GPMI:
- Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
SPI NOR core changes:
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
- Avoid crossing 4K address boundary on read/write
- Add support for Intel Comet Lake SPI serial flash"
* tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (120 commits)
mtd: part: fix incorrect format specifier for an unsigned long long
mtd: lpddr_cmds: Mark expected switch fall-through
mtd: phram: Mark expected switch fall-throughs
mtd: cfi_cmdset_0002: Mark expected switch fall-throughs
mtd: cfi_util: mark expected switch fall-throughs
MAINTAINERS: MTD Git repository is hosted on kernel.org
MAINTAINERS: Update jffs2 entry
mtd: afs: add v2 partition parsing
mtd: afs: factor the IIS read into partition parser
mtd: afs: factor footer parsing into the v1 part parsing
mtd: factor out v1 partition parsing
mtd: afs: simplify partition detection
mtd: afs: simplify partition parsing
mtd: partitions: Add OF support to AFS partitions
mtd: partitions: Add AFS partitions DT bindings
mtd: afs: Move AFS partition parser to parsers subdir
mtd: maps: Make uclinux_ram_map static
mtd: maps: Allow MTD_PHYSMAP with MTD_RAM
MAINTAINERS: Add myself as MTD maintainer
MAINTAINERS: Remove my name from the MTD and NAND entries
...
Since the migration of the driver to stop using the legacy
->select_chip() hook, there is nothing deselecting the target anymore,
thus the selection is not forced at the next access. Ensure the ND_RUN
bit and the interrupts are always in a clean state.
Cc: Daniel Mack <daniel@zonque.org>
Cc: stable@vger.kernel.org
Fixes: b25251414f ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Since the migration of the driver to stop using the legacy
->select_chip() hook, the marvell_nfc_select_chip() helper has been
'renamed' to marvell_nfc_select_target(). Update a left-over reference
to this helper in a comment in the ->resume() path.
Fixes: b25251414f ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
nand_device embeds a nand_ecc_req object which contains the minimum
strength and step-size required by the NAND device.
Drop the chip->ecc_{strength,step}_ds fields and use
chip->base.eccreq.{strength,step_size} instead.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
We plan to move cache related fields to a pagecache struct in nand_chip
but some drivers access ->pagebuf directly to invalidate the cache
before they start using ->data_buf.
Let's provide an helper that returns a pointer to ->data_buf after
invalidating the cache.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
marvell_nfc_wait_op() waits for completion during 'timeout_ms'
milliseconds before throwing an error. While the logic is fine, the
value of 'timeout_ms' is given by the core and actually correspond to
the maximum time the NAND chip will take to complete the
operation. Assuming there is no overhead in the propagation of the
interrupt signal to the the NAND controller (through the Ready/Busy
line), this delay does not take into account the latency of the
operating system. For instance, for a page write, the delay given by
the core is rounded up to 1ms. Hence, when the machine is over loaded,
there is chances that this timeout will be reached.
There are two ways to solve this issue that are not incompatible:
1/ Enlarge the timeout value (if so, how much?).
2/ Check after the waiting method if we did not miss any interrupt
because of the OS latency (an interrupt is still pending). In this
case, we assume the operation exited successfully.
We choose the second approach that is a must in all cases, with the
possibility to also modify the timeout value to be, e.g. at least 1
second in all cases.
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
->setup_data_interface() is a controller specific method and should
thus be placed in nand_controller_ops.
In order to make that work with controllers that support keeping
pre-configured timings we need to add a new NAND_KEEP_TIMINGS flag to
inform the core it should skip the timings selection step.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
->exec_op() is a controller method and has nothing to do in the
nand_chip struct. Let's move it to the nand_controller_ops struct and
adjust the core and drivers accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
