IPV is added and used term in 802.1Qci PSFP and merged into 802.1Q (from
802.1Q-2018) for another functions.
Even it does similar operation holding temporal priority value
internally (as it is named), because KSZ datasheet doesn't use the term
of IPV (Internal Priority Value) and avoiding any confusion later when
PSFP is in the Linux world, it is better to rename IPV to IPM (Internal
Priority Mapping).
In addition, LAN937x documentation already use IPV for 802.1Qci PSFP
related functionality.
Suggested-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240510053828.2412516-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Microchip KSZ and LAN variants do not have per port DSCP priority
configuration. Instead there is a global DSCP mapping table.
This patch provides write access to this global DSCP map. In case entry
is "deleted", we map corresponding DSCP entry to a best effort prio,
which is expected to be the default priority for all untagged traffic.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Init priority to queue mapping in the way as it shown in IEEE 802.1Q
mapping example.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I tested ETS support on KSZ9893, so it should work other KSZ989X
variants too, which was till not listed as support.
With this change we now officially not support only ksz8 family of
chips.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DCB support to configure app trust sources and default port priority.
Following commands can be used for testing:
dcb apptrust set dev lan1 order pcp dscp
dcb app replace dev lan1 default-prio 3
Since it is not possible to configure DSCP-Prio mapping per port, this
patch provide only ability to read switch global dscp-prio mapping and
way to enable/disable app trust for DSCP.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of Microchip KSZ switches use Internal Priority Value associated
with every frame. For example, it is possible to map any VLAN PCP or
DSCP value to IPV and at the end, map IPV to a queue.
Since amount of IPVs is not equal to amount of queues, add this
information and make use of it in some functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert ksz_common to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1s0O7H-009gpq-IF@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phylink_mac_config function pointer member of struct ksz_dev_ops is
never initialised, so let's remove it to simplify the code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1s0O7C-009gpk-Dh@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver has two separate reset sequence in different places:
- gpio/HW reset on start of ksz_switch_register()
- SW reset on start of ksz_setup()
The second one will overwrite drive strength configuration made in the
ksz_switch_register().
To fix it, move ksz_parse_drive_strength() from ksz_switch_register() to
ksz_setup().
Fixes: d67d7247f6 ("net: dsa: microchip: Add drive strength configuration")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240304135612.814404-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement bridge port isolation for KSZ switches. Enabling the isolation
of switch ports from each other while maintaining connectivity with the
CPU and other forwarding ports. For instance, to isolate swp1 and swp2
from each other, use the following commands:
- bridge link set dev swp1 isolated on
- bridge link set dev swp2 isolated on
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit introduces support for the KSZ8567, a robust 7-port
Ethernet switch. The KSZ8567 features two RGMII/MII/RMII interfaces,
each capable of gigabit speeds, complemented by five 10/100 Mbps
MAC/PHYs.
Signed-off-by: Philippe Schenker <philippe.schenker@impulsing.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240130083419.135763-2-dev@pschenker.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the use of define DSA_TAG_PROTO_LAN937X_VALUE to
DSA_TAG_PROTO_LAN937X to improve readability.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20231206160124.1935451-1-sean@geanix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide a list of valid protocols for which the driver will provide
it's deferred xmit handler.
When using DSA_TAG_PROTO_KSZ8795 protocol, it does not provide a
"connect" method, therefor ksz_connect() is not allocating ksz_tagger_data.
This avoids the following null pointer dereference:
ksz_connect_tag_protocol from dsa_register_switch+0x9ac/0xee0
dsa_register_switch from ksz_switch_register+0x65c/0x828
ksz_switch_register from ksz_spi_probe+0x11c/0x168
ksz_spi_probe from spi_probe+0x84/0xa8
spi_probe from really_probe+0xc8/0x2d8
Fixes: ab32f56a41 ("net: dsa: microchip: ptp: add packet transmission timestamping")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20231206071655.1626479-1-sean@geanix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ksz driver has bits and pieces of platform_data probing support, but
it doesn't work.
The conventional thing to do is to have an encapsulating structure for
struct dsa_chip_data that gets put into dev->platform_data. This driver
expects a struct ksz_platform_data, but that doesn't contain a struct
dsa_chip_data as first element, which will obviously not work with
dsa_switch_probe() -> dsa_switch_parse().
Pointing dev->platform_data to a struct dsa_chip_data directly is in
principle possible, but that doesn't work either. The driver has
ksz_switch_detect() to read the device ID from hardware, followed by
ksz_check_device_id() to compare it against a predetermined expected
value. This protects against early errors in the SPI/I2C communication.
With platform_data, the mechanism in ksz_check_device_id() doesn't work
and even leads to NULL pointer dereferences, since of_device_get_match_data()
doesn't work in that probe path.
So obviously, the platform_data support is actually missing, and the
existing handling of struct ksz_platform_data is bogus. Complete the
support by adding a struct dsa_chip_data as first element, and fixing up
ksz_check_device_id() to pick up the platform_data instead of the
unavailable of_device_get_match_data().
The early dev->chip_id assignment from ksz_switch_register() is also
bogus, because ksz_switch_detect() sets it to an initial value. So
remove it.
Also, ksz_platform_data :: enabled_ports isn't used anywhere, delete it.
Link: https://lore.kernel.org/netdev/20231204154315.3906267-1-dd@embedd.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Daniel Danzberger <dd@embedd.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last part of the driver do now support phylink_mac_link_up(). So, make it
not optional.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20231127145101.3039399-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch introduces the function 'ksz8_phy_port_link_up' to the
Microchip KSZ8xxx driver. This function is responsible for setting up
flow control and duplex settings for the ports that are integrated with
PHYs.
The KSZ8795 switch supports asymmetric pause control, which can't be
fully utilized since a single bit controls both RX and TX pause. Despite
this, the flow control can be adjusted based on the auto-negotiation
process, taking into account the capabilities of both link partners.
On the other hand, the KSZ8873's PORT_FORCE_FLOW_CTRL bit can be set by
the hardware bootstrap, which ignores the auto-negotiation result.
Therefore, even in auto-negotiation mode, we need to ensure that this
bit is correctly set.
When auto-negotiation isn't in use, we enforce symmetric pause control
for the KSZ8795 switch.
Please note, forcing flow control disable on a port while still
advertising pause support isn't possible. While this scenario
might not be practical or desired, it's important to be aware of this
limitation when working with the KSZ8873 and similar devices.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20231127145101.3039399-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow flow control, speed, and duplex settings on the CPU port to be
configurable. Previously, the speed and duplex relied on default switch
values, which limited flexibility. Additionally, flow control was
hardcoded and only functional in duplex mode. This update enhances the
configurability of these parameters.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20231127145101.3039399-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ensures a stable PME (Power Management Event) pin state by disabling PME
on system start and enabling it on shutdown only if WoL (Wake-on-LAN) is
configured. This is needed to avoid issues with some PMICs (Power
Management ICs).
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20231026051051.2316937-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Centralize the switch shutdown routine in a dedicated function,
ksz_switch_shutdown(), to enhance code maintainability and reduce
redundancy. This change abstracts the common shutdown operations
previously duplicated in ksz9477_i2c_shutdown() and ksz_spi_shutdown().
This refactoring is a preparatory step for an upcoming patch to avoid
reset on shutdown if Wake-on-LAN (WoL) is enabled.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20231026051051.2316937-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enhance the ksz_switch_macaddr_get() function to handle errors that may
occur during the call to ksz_write8(). Specifically, this update checks
the return value of ksz_write8(), which may fail if regmap ranges
validation is not passed and returns the error code.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20231026051051.2316937-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce Wake on Magic Packet (WoL) functionality to the ksz9477
driver.
Major changes include:
1. Extending the `ksz9477_handle_wake_reason` function to identify Magic
Packet wake events alongside existing wake reasons.
2. Updating the `ksz9477_get_wol` and `ksz9477_set_wol` functions to
handle WAKE_MAGIC alongside the existing WAKE_PHY option, and to
program the switch's MAC address register accordingly when Magic
Packet wake-up is enabled. This change will prevent WAKE_MAGIC
activation if the related port has a different MAC address compared
to a MAC address already used by HSR or an already active WAKE_MAGIC
on another port.
3. Adding a restriction in `ksz_port_set_mac_address` to prevent MAC
address changes on ports with active Wake on Magic Packet, as the
switch's MAC address register is utilized for this feature.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20231026051051.2316937-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add WoL support for KSZ9477 family of switches. This code was tested on
KSZ8563 chip.
KSZ9477 family of switches supports multiple PHY events:
- wake on Link Up
- wake on Energy Detect.
Since current UAPI can't differentiate between this PHY events, map all
of them to WAKE_PHY.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ switches with WoL support signals wake event over PME pin. If this
pin is attached to some external PMIC or System Controller can't be
described as GPIO, the only way to describe it in the devicetree is to
use wakeup-source property. So, add support for this property and enable
PME switch output if this property is present.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing offset for the global MAC address register
(REG_SW_MAC_ADDR) for the ksz8863 family of switches.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more inclusive terms throughout the DSA subsystem by moving away
from "master" which is replaced by "conduit" and "slave" which is
replaced by "user". No functional changes.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231023181729.1191071-2-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds functions for providing in KSZ9477 switch HSR
(High-availability Seamless Redundancy) hardware offloading.
According to AN3474 application note following features are provided:
- TX packet duplication from host to switch (NETIF_F_HW_HSR_DUP)
- RX packet duplication discarding
- Prevention of packet loop
For last two ones - there is a probability that some packets will not
be filtered in HW (in some special cases - described in AN3474).
Hence, the HSR core code shall be used to discard those not caught frames.
Moreover, some switch registers adjustments are required - like setting
MAC address of HSR network interface.
Additionally, the KSZ9477 switch has been configured to forward frames
between HSR ports (e.g. 1,2) members to provide support for
NETIF_F_HW_HSR_FWD flag.
Join and leave functions are written in a way, that are executed with
single port - i.e. configuration is NOT done only when second HSR port
is configured.
Co-developed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Defining macros which have the same name but different values is bad
practice, because it makes it hard to avoid code duplication. The same
code does different things, depending on the file it's placed in.
Case in point, we want to access REG_SW_MAC_ADDR from ksz_common.c, but
currently we can't, because we don't know which kszXXXX_reg.h to include
from the common code.
Remove the REG_SW_MAC_ADDR_{0..5} macros from ksz8795_reg.h and
ksz9477_reg.h, and re-add this register offset to the dev->info->regs[]
array.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch adds partial Access Control List (ACL) support for the
ksz9477 family of switches. ACLs enable filtering of incoming layer 2
MAC, layer 3 IP, and layer 4 TCP/UDP packets on each port. They provide
additional capabilities for filtering routed network protocols and can
take precedence over other forwarding functions.
ACLs can filter ingress traffic based on header fields such as
source/destination MAC address, EtherType, IPv4 address, IPv4 protocol,
UDP/TCP ports, and TCP flags. The ACL is an ordered list of up to 16
access control rules programmed into the ACL Table. Each entry specifies
a set of matching conditions and action rules for controlling packet
forwarding and priority.
The ACL also implements a count function, generating an interrupt
instead of a forwarding action. It can be used as a watchdog timer or an
event counter. The ACL consists of three parts: matching rules, action
rules, and processing entries. Multiple match conditions can be either
AND'ed or OR'ed together.
This patch introduces support for a subset of the available ACL
functionality, specifically layer 2 matching and prioritization of
matched packets. For example:
tc qdisc add dev lan2 clsact
tc filter add dev lan2 ingress protocol 0x88f7 flower action skbedit prio 7
tc qdisc add dev lan1 clsact
tc filter add dev lan1 ingress protocol 0x88f7 flower action skbedit prio 7
The hardware offloading implementation was benchmarked against a
configuration without hardware offloading. This latter setup relied on a
software-based Linux bridge. No noticeable differences were observed
between the two configurations. Here is an example of software-based
test:
ip l s dev enu1u1 up
ip l s dev enu1u2 up
ip l s dev enu1u4 up
ethtool -A enu1u1 autoneg off rx off tx off
ethtool -A enu1u2 autoneg off rx off tx off
ethtool -A enu1u4 autoneg off rx off tx off
ip l a name br0 type bridge
ip l s dev br0 up
ip l s enu1u1 master br0
ip l s enu1u2 master br0
ip l s enu1u4 master br0
tc qdisc add dev enu1u1 root handle 1: ets strict 4 priomap 3 3 2 2 1 1 0 0
tc qdisc add dev enu1u4 root handle 1: ets strict 4 priomap 3 3 2 2 1 1 0 0
tc qdisc add dev enu1u2 root handle 1: ets strict 4 priomap 3 3 2 2 1 1 0 0
tc qdisc add dev enu1u1 clsact
tc filter add dev enu1u1 ingress protocol ipv4 flower action skbedit prio 7
tc qdisc add dev enu1u4 clsact
tc filter add dev enu1u4 ingress protocol ipv4 flower action skbedit prio 0
On a system attached to the port enu1u2 I run two iperf3 server
instances:
iperf3 -s -p 5210 &
iperf3 -s -p 5211 &
On systems attached to enu1u4 and enu1u1 I run:
iperf3 -u -c 172.17.0.1 -p 5210 -b100M -l1472 -t100
and
iperf3 -u -c 172.17.0.1 -p 5211 -b100M -l1472 -t100
As a result, IP traffic on port enu1u1 will be prioritized and take
precedence over IP traffic on port enu1u4
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, the *_port_setup code is in dsa_switch_ops::port_enable(),
which is not the best place for it. This patch moves it to a more
suitable place, dsa_switch_ops::port_setup(), to match the function's
purpose and name.
This patch is a preparation for coming ACL support patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree based drive strength configuration support. It is needed to
pass EMI validation on our hardware.
Configuration values are based on the vendor's reference driver.
Tested on KSZ9563R.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9477 errata points out (in 'Module 4') the link up/down problems
when EEE (Energy Efficient Ethernet) is enabled in the device to which
the KSZ9477 tries to auto negotiate.
The suggested workaround is to clear advertisement of EEE for PHYs in
this chip driver.
To avoid regressions with other switch ICs the new MICREL_NO_EEE flag
has been introduced.
Moreover, the in-register disablement of MMD_DEVICE_ID_EEE_ADV.MMD_EEE_ADV
MMD register is removed, as this code is both; now executed too late
(after previous rework of the PHY and DSA for KSZ switches) and not
required as setting all members of eee_broken_modes bit field prevents
the KSZ9477 from advertising EEE.
Fixes: 69d3b36ca0 ("net: dsa: microchip: enable EEE support") # for KSZ9477
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # Confirmed disabled EEE with oscilloscope.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230905093315.784052-1-lukma@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit (SHA1: 5c844d57aa) provided code
to apply "Module 6: Certain PHY registers must be written as pairs instead
of singly" errata for KSZ9477 as this chip for certain PHY registers
(0xN120 to 0xN13F, N=1,2,3,4,5) must be accesses as 32 bit words instead
of 16 or 8 bit access.
Otherwise, adjacent registers (no matter if reserved or not) are
overwritten with 0x0.
Without this patch some registers (e.g. 0x113c or 0x1134) required for 32
bit access are out of valid regmap ranges.
As a result, following error is observed and KSZ9477 is not properly
configured:
ksz-switch spi1.0: can't rmw 32bit reg 0x113c: -EIO
ksz-switch spi1.0: can't rmw 32bit reg 0x1134: -EIO
ksz-switch spi1.0 lan1 (uninitialized): failed to connect to PHY: -EIO
ksz-switch spi1.0 lan1 (uninitialized): error -5 setting up PHY for tree 0, switch 0, port 0
The solution is to modify regmap_reg_range to allow accesses with 4 bytes
boundaries.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230724211859.805481-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since DSA no longer marks anything as phylink-legacy, there is now no
need for DSA drivers to set this member to false. Remove all instances
of this.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The KSZ8795 driver code was modified to use on KSZ8863/73, which has
different register definitions. Some of the new KSZ8795 register
information are wrong compared to previous code.
KSZ8795 also behaves differently in that the STATIC_MAC_TABLE_USE_FID
and STATIC_MAC_TABLE_FID bits are off by 1 when doing MAC table reading
than writing. To compensate that a special code was added to shift the
register value by 1 before applying those bits. This is wrong when the
code is running on KSZ8863, so this special code is only executed when
KSZ8795 is detected.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9477 PHY errata handling code has now been moved into the Micrel
PHY driver, so it is no longer needed inside the DSA switch driver.
Remove it.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This update introduces specific register access boundaries for the
KSZ8873 and KSZ8863 chips within the DSA Microchip driver. The outlined
ranges target global control registers, port registers, and advanced
control registers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It is not immediately obvious that this driver allocates, via the
KSZ_REGMAP_TABLE() macro, 3 regmaps for register access: dev->regmap[0]
for 8-bit access, dev->regmap[1] for 16-bit and dev->regmap[2] for
32-bit access.
In future changes that add support for reg_fields, each field will have
to specify through which of the 3 regmaps it's going to go. Add an enum
now, to denote one of the 3 register access widths, and make the code go
through some wrapper functions for easier review and further
modification.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for add/del_fdb operations and utilize the refactored static
MAC table code. This resolves kernel warnings caused by the lack of fdb
add function support in the current driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
FID is directly mapped to VID. However, configuring a MAC address with a
VID != 0 resulted in incorrect configuration due to an incorrect bit
mask. This kernel commit fixed the issue by correcting the bit mask and
ensuring proper configuration of MAC addresses with non-zero VID.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the dynamic MAC table is empty, we will still extract one outdated
entry. Fix it by using correct bit offset.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
