Update the SM8650 UFS PHY init tables to support Gear 4 and Gear 5
using the overlays setup (only supported Gear 5 before), and sync
back with the latest Qualcomm recommended values.
The new recommended values allow a solid 50% bump in sequential
read/write benchmarks on the SM8650 QRD & HDK reference boards.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240410-topic-sm8650-upstream-ufs-g5-v1-1-5527c44b37e6@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Device drivers should just rely on the clocks provided by the devicetree
and enable/disable them based on the requirement. There is no need to
validate the clocks provided by devicetree in the driver. That's the job
of DT schema.
So let's switch to devm_clk_bulk_get_all() API that just gets the clocks
provided by devicetree and remove hardcoded clocks info.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-2-58a49d2f4605@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On SM8550, two sets of UFS PHY settings are provided, one set is to support
HS-G5, another set is to support HS-G4 and lower gears. The two sets of PHY
settings are programming different values to different registers, mixing
the two sets and/or overwriting one set with another set is definitely not
blessed by UFS PHY designers.
To add HS-G5 support for SM8550, split the two sets of PHY settings into
their dedicated overlay tables, only the common parts of the two sets of
PHY settings are left in the .tbls.
Consider we are going to add even higher gear support in future, to avoid
adding more tables with different names, rename the .tbls_hs_g4 and make it
an array, a size of 2 is enough as of now.
In this case, .tbls alone is not a complete set of PHY settings, so either
tbls_hs_overlay[0] or tbls_hs_overlay[1] must be applied on top of the
.tbls to become a complete set of PHY settings.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1703557892-1822-1-git-send-email-quic_cang@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SC7180 UFS PHY is identical to the one found on SM7150. Add a
compatible for it.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: David Wronek <davidwronek@gmail.com>
Link: https://lore.kernel.org/r/20240121-sm7125-upstream-v4-5-f7d1212c8ebb@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The registers, which are being touched in current SM8550 UFS PHY settings,
and the values being programmed are mainly the ones working for HS-G4 mode,
meanwhile, there are also a few ones somehow taken from HS-G5 PHY settings.
However, even consider HS-G4 mode only, some of them are incorrect and some
are missing. Rectify the HS-G4 PHY settings by strictly aligning with the
SM8550 UFS PHY Hardware Programming Guide suggested HS-G4 PHY settings.
Fixes: 1679bfef90 ("phy: qcom-qmp-ufs: Add SM8550 support")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/1701520577-31163-10-git-send-email-quic_cang@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The conversion commit 7559e7572c ("phy: Explicitly include correct DT
includes") misses offsets configuration for sm8150 (most likely it was
developed separately from the series adding HS G4 support and was not
adapted for the sm8150/sm8250 configuration split).
Add missing offsets to sm8150_ufsphy_cfg.
Fixes: 7559e7572c ("phy: Explicitly include correct DT includes")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230731111009.3998089-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/phy/phy-can-transceiver.c
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20230714174841.4061919-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Populate offsets configuration for the rest of UFS PHYs to make it
possible to switch them to the new (single-node) bindings style.
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230711145153.4167820-3-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add QMP PHY config for sa8775p and add support for the new compatible.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230411130446.401440-4-brgl@bgdev.pl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the tables and constants for init sequences for UFS QMP phy found in
SM7150 SoC.
Signed-off-by: David Wronek <davidwronek@gmail.com>
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230311231733.141806-3-danila@jiaxyga.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The new SM8550 SoC bumps up the HW version of QMP phy to v6 for USB,
UFS and PCIE g3x2. Add the new PCS UFS specific offsets in a dedicated
header file.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230117224148.1914627-6-abel.vesa@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The new SM8550 SoC bumps up the HW version of QMP phy to v6 for USB,
UFS and PCIE g3x2. Add the new qserdes TX RX but UFS specific offsets
in a dedicated header file.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230117224148.1914627-5-abel.vesa@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All currently known QMP UFS PHYs have the same offsets for register
sub-regions. Instead of using qmp_ufs_offsets_v5 for older generations
of PHYs, rename the offsets struct instance to remove _v5 suffix.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230113195515.407866-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
UFS PHY in SC8280XP SoC is capable of operating at HS G4 mode and the init
sequence is compatible with SM8350. Hence, add the tbls_hs_g4 instance
reusing the G4 init sequence of SM8350.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-13-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
UFS PHY in SM8450 SoC is capable of operating at HS G4 mode and the init
sequence is compatible with SM8350. Hence, add the tbls_hs_g4 instance
reusing the G4 init sequence of SM8350.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-12-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
SM8350 default init sequence sets some PCS registers to HS G3, thereby
disabling HS G4 mode. This has the effect on MPHY capability negotiation
between the host and the device during link startup and causes the
PA_MAXHSGEAR to G3 irrespective of device max gear.
Due to that, the agreed gear speed determined by the UFS core will become
G3 only and the platform won't run at G4.
So, let's remove setting these registers for SM8350 as like other G4
compatible platforms. One downside of this is that, when the board design
uses non-G4 compatible device, then MPHY will continue to run in the
default mode (G4) even if UFSHCD runs in G3. But this is the case for
other platforms as well.
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
UFS PHY in SM8250 SoC is capable of operating at HS G4 mode. Hence, add the
required register settings using the tables_hs_g4 struct instance. This
also requires a separate qmp_phy_cfg for SM8250 instead of reusing SM8150.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since now there is support for configuring the HS Rate B mode properly,
let's move the register setting to tbls_hs_b struct for all SoCs.
This allows the PHY to be configured in Rate A initially and then in
Rate B if requested by the UFS driver.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add separate tables_hs_g4 instance to allow the PHY driver to configure the
PHY in HS G4 mode. The individual SoC configs need to supply the Rx, Tx and
PCS register setting in tables_hs_g4 and the UFS driver can request the
Hs G4 mode by calling phy_set_mode_ext() with submode set to UFS_HS_G4.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add separate tables_hs_b instance to allow the PHY driver to configure the
PHY in HS Series B mode. The individual SoC configs need to supply the
serdes register setting in tables_hs_b and the UFS driver can request the
Series B mode by calling phy_set_mode() with mode set to PHY_MODE_UFS_HS_B.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As done for Qcom PCIe PHY driver, let's move the register settings to the
common qmp_phy_cfg_tbls struct. This helps in adding any additional PHY
settings needed for functionalities like HS-G4 in the future by adding one
more instance of the qmp_phy_cfg_tbls.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Only MSM8996 is using "_ufs_" naming convention for PHY definitions instead
of "_ufsphy_" as like other SoCs. So to maintain the uniformity, let's
rename all of the definitions to use "_ufsphy_".
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Following the other QMP PHY drivers like PCIe, let's remove the "_tbl"
suffix from the qmp_phy_init_tbl definitions. This helps in maintaining
the uniformity across all of the QMP PHY drivers.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SM6125 UFS PHY is compatible with the one from SM6115. Add a
compatible for it and modify the config from SM6115 to make them
compatible with the SC8280XP binding
Signed-off-by: Lux Aliaga <they@mint.lgbt>
Reviewed-by: Martin Botka <martin.botka@somainline.org>
Link: https://lore.kernel.org/r/20230108195336.388349-4-they@mint.lgbt
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove QMP PHY type-specific headers inclusion from the common header
and move them to the specific PHY drivers to cleanup the namespaces used
by different drivers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221110192248.873973-14-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use symbolic names for the values inside reg layout arrays. New register
names are added following the PCS register layout that is used by the
particular PHY.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221110192248.873973-8-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Register three UFS symbol clocks (ufs_rx_symbol_0_clk_src,
ufs_rx_symbol_1_clk_src ufs_tx_symbol_0_clk_src). Register OF clock
provider to let other devices link these clocks through the DT.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221123104443.3415267-3-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PHY type defines are no longer used in the PCIe, UFS and USB QMP
drivers so drop the corresponding include.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221111094239.11547-2-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the new SC8280XP binding.
Note that the binding does not try to describe every register subregion
and instead the driver holds the corresponding offsets.
Also note that the driver will continue to accept the old binding, at
least for the time being.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-11-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for supporting devicetree bindings which do not use a
child node, move the PHY creation to probe() proper and parse the serdes
resource in what is now the legacy devicetree helper.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-10-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Clean up the PHY initialisation somewhat programming both tx and rx for
the second lane after the first lane.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-7-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Rename the PHY operation structure so that it has a "phy_ops" suffix and
move it next to the implementation.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-6-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stop abusing the driver data pointer and instead pass the driver state
structure directly to the initialisation helpers during probe.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-5-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since the QMP driver split there will be at most a single child node so
drop the obsolete iteration construct.
While at it, drop the verbose error logging that would have been
printed also on probe deferrals.
Note that there's no need to check if there are additional child nodes
(the kernel is not a devicetree validator), but let's return an error if
there are no child nodes at all for now.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-4-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The UFS QMP PHY driver only manages a single PHY so merge the old
qcom_qmp and qmp_phy structures and drop the PHY array.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-3-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Move the device-id table below probe() and next to the driver structure
to keep the driver callback functions grouped together.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-2-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drop the start and pwrdn-ctrl abstractions which are no longer needed
since the QMP driver split.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221012085002.24099-19-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It typically takes between one and two milliseconds for the PHY to
become ready after starting it. Increase the tight 3--10 us polling
period to the more reasonable 51--200 us.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221012085002.24099-12-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Clean up the PHY ready polling by dropping the mask variables which are
no longer needed since the QMP driver split.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221012085002.24099-11-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drop the unused phy-status configuration mask which has never been used
for UFS PHYs.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221012085002.24099-10-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
