Use the new skl_int3472_gpiod_get_from_temp_lookup() helper to get
a gpio to pass to register_gpio_clock(), skl_int3472_register_regulator()
and skl_int3472_register_pled().
This removes all use of the deprecated gpiod_toggle_active_low() and
acpi_get_and_request_gpiod() functions.
Suggested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20231004162317.163488-4-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Add an "AVDD" regulator supply name alias to the supply-map which
gets registered for the INT3472 GPIO regulator.
This is necessary for the ov2680 driver which expects "AVDD" rather then
"avdd". Updating the ov2680 driver to use "avdd" is not possible because
that will break compatibility with existing DT / DTB files.
Tested-by: Hao Yao <hao.yao@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230616172132.37859-5-hdegoede@redhat.com
On the Lenovo Miix 510-12IKB there is 1 GPIO regulator, with its GPIO
listed in the INT3472 device belonging to the OV5648 back sensor.
But this regulator also needs to be enabled for the OV2680 front sensor
to work.
Add support to skl_int3472_register_regulator() to add supply map entries
pointing to both sensors based on a DMI quirk table which gives the
dev_name part of the supply map for the second sensor (the sensor without
the GPIO listed in its matching INT3472 ACPI device).
Tested-by: Hao Yao <hao.yao@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230616172132.37859-4-hdegoede@redhat.com
Currently the only 2 sensor_config-s both specify "avdd" as supply-id.
The INT3472 device is going to be the only supplier of a regulator for
the sensor device.
So there is no chance of collisions with other regulator suppliers
and it is undesirable to need to manually add new entries to
int3472_sensor_configs[] for each new sensor module which uses
a GPIO regulator.
Instead just always use "avdd" as supply-id when registering
the GPIO regulator.
If necessary for specific sensor drivers then other supply-ids can
be added as aliases in the future, adding aliases will be safe
since INT3472 will be the only regulator supplier for the sensor.
Cc: Bingbu Cao <bingbu.cao@intel.com>
Tested-by: Hao Yao <hao.yao@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230616172132.37859-3-hdegoede@redhat.com
The only sensor driver which needs GPIO remapping support is the ov2680
driver and ACPI enumeration support + other necessary changes to
the ov2680 driver were never upstreamed.
A new series updating the ov2680 driver is pending upstream now and
in this series the ov2680 driver is patched to look for "powerdown"
as con-id, instead of relying on GPIO remapping in the int3472 code,
so the GPIO remapping is no longer necessary.
Tested-by: Hao Yao <hao.yao@intel.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230616172132.37859-2-hdegoede@redhat.com
According to:
https://github.com/intel/ipu6-drivers/blob/master/patch/int3472-support-independent-clock-and-LED-gpios-5.17%2B.patch
Bits 31-24 of the _DSM pin entry integer value codes the active-value,
that is the actual physical signal (0 or 1) which needs to be output on
the pin to turn the sensor chip on (to make it active).
So if bits 31-24 are 0 for a reset pin, then the actual value of the reset
pin needs to be 0 to take the chip out of reset. IOW in this case the reset
signal is active-high rather then the default active-low.
And if bits 31-24 are 0 for a clk-en pin then the actual value of the clk
pin needs to be 0 to enable the clk. So in this case the clk-en signal
is active-low rather then the default active-high.
IOW if bits 31-24 are 0 for a pin, then the default polarity of the pin
is inverted.
Add a check for this and also propagate this new polarity to the clock
registration.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20230127203729.10205-6-hdegoede@redhat.com
Move the requesting of the clk-enable GPIO to skl_int3472_register_clock()
(and move the gpiod_put to unregister).
This mirrors the GPIO handling in skl_int3472_register_regulator() and
allows removing skl_int3472_map_gpio_to_clk() from discrete.c.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20230127203729.10205-5-hdegoede@redhat.com
On some systems, e.g. the Lenovo ThinkPad X1 Yoga gen 7 and the ThinkPad
X1 Nano gen 2 there is no clock-enable pin, triggering the:
"No clk GPIO. The privacy LED won't work" warning and causing the privacy
LED to not work.
Fix this by modeling the privacy LED as a LED class device rather then
integrating it with the registered clock.
Note this relies on media subsys changes to actually turn the LED on/off
when the sensor's v4l2_subdev's s_stream() operand gets called.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20230127203729.10205-4-hdegoede@redhat.com
The discrete.c code is not the only code which needs to lookup the
acpi_device and device-name for the sensor for which the INT3472
ACPI-device is a GPIO/clk/regulator provider.
The tps68470.c code also needs this functionality, so factor this
out into a new get_sensor_adev_and_name() helper.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-9-hdegoede@redhat.com
The intel_skl_int3472.ko module contains 2 separate drivers,
the int3472_discrete platform driver and the int3472_tps68470
I2C-driver.
These 2 drivers contain very little shared code, only
skl_int3472_get_acpi_buffer() and skl_int3472_fill_cldb() are
shared.
Split the module into 2 drivers, linking the little shared code
directly into both.
This will allow us to add soft-module dependencies for the
tps68470 clk, gpio and regulator drivers to the new
intel_skl_int3472_tps68470.ko to help with probe ordering issues
without causing these modules to get loaded on boards which only
use the int3472_discrete platform driver.
While at it also rename the .c and .h files to remove the
cumbersome intel_skl_int3472_ prefix.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-8-hdegoede@redhat.com
2021-12-13 11:44:48 +01:00
Renamed from drivers/platform/x86/intel/int3472/intel_skl_int3472_common.h (Browse further)
