Switch to the ->device_configure method instead of ->slave_configure and
update the block limits on the passed in queue_limits instead of using the
per-limit accessors.
Note that mpi3mr also updates the limits from an event handler that
iterates all SCSI devices. This is also updated to use the queue_limits,
but the complete locking of this path probably means it already is
completely broken and needs a proper audit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240409143748.980206-22-hch@lst.de
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver did not remove the virtual disk that was exposed as hidden and
offline after the controller was reset.
Drive is removed from OS when firmware sends "device added" event with
hidden bit set or access status indicating inability to accept I/Os.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Link: https://lore.kernel.org/r/20240313100746.128951-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver acquires the required NVMe SGLs from the pre-allocated
pool.
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20231205191630.12201-4-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver acquires the required SGLs from the pre-allocated pool.
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20231205191630.12201-3-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver now supports SGLs for BSG data transfer. Upon loading, the
driver pre-allocates SGLs in chunks of 8k, results in a total of 256 * 8k,
equal to 2MB. These pre-allocated SGLs are reserved for handling BSG
commands and are deallocated during driver unload.
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20231205191630.12201-2-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SAS5116 controllers supports maximum 48 physical PHYs. Modify driver to
accommodate up to 64 PHYs (though current need is to support 48 PHYs).
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20231123160132.4155-4-sumit.saxena@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enhance the driver to get the maximum data length per I/O request from IOC
Facts data and report that to the upper layers. If the IOC facts data is
not reported then a default I/O size of 1MB is reported to the OS.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20230804104248.118924-4-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update driver version to 8.4.1.0.0.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230316110209.60145-9-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update copyright year from 2022 to 2023.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230316110209.60145-8-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify Message Unit Reset timeout value to 120 seconds from the previous
value of 30 seconds.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekant Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230316110209.60145-4-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Upon Virtual disk removal, firmware sends device status change event
(Virtual disk remove event) and expects the driver to start device remove
handshake (by sending target reset and IOU control command to firmware).
However, the driver does not initiate the device remove handshake which
leads to the firmware fault.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230316110209.60145-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a missing resource clean up in .remove.
Fixes: e22bae3066 ("scsi: mpi3mr: Add expander devices to STL")
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Link: https://lore.kernel.org/r/20230302234336.25456-7-thenzl@redhat.com
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As part of Task Management handling, the driver will disable and enable the
MSIx index zero which belongs to the Admin reply queue. During this
transition the driver loses some interrupts and this leads to Admin request
and ioctl timeouts.
After enabling the interrupts, poll the Admin reply queue to avoid
timeouts.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230228140835.4075-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To allocate bitmaps, the mpi3mr driver calculates sizes of bitmaps using
byte as unit. However, bitmap helper functions assume that bitmaps are
allocated using unsigned long as unit. This gap causes memory access beyond
the bitmap sizes and results in "BUG: KASAN: slab-out-of-bounds". The BUG
was observed at firmware download to eHBA-9600. Call trace indicated that
the out-of-bounds access happened in find_first_zero_bit() called from
mpi3mr_send_event_ack() for miroc->evtack_cmds_bitmap.
To fix the BUG, do not use bytes to manage bitmap sizes. Instead, use
number of bits, and call bitmap helper functions which take number of bits
as arguments. For memory allocation, call bitmap_zalloc() instead of
kzalloc() and krealloc(). For memory free, call bitmap_free() instead of
kfree(). For zero clear, call bitmap_clear() instead of memset().
Remove three fields for bitmap byte sizes in struct scmd_priv which are no
longer required. Replace the field dev_handle_bitmap_sz with
dev_handle_bitmap_bits to keep number of bits of removepend_bitmap across
resize.
Link: https://lore.kernel.org/r/20230214005019.1897251-4-shinichiro.kawasaki@wdc.com
Fixes: c5758fc72b ("scsi: mpi3mr: Gracefully handle online FW update operation")
Fixes: e844adb1fb ("scsi: mpi3mr: Implement SCSI error handler hooks")
Fixes: c1af985d27 ("scsi: mpi3mr: Add Event acknowledgment logic")
Fixes: 824a156633 ("scsi: mpi3mr: Base driver code")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix 'scheduling while atomic' type bug, which is observed when
pci_irq_vector() is called from interrupt context.
Link: https://lore.kernel.org/r/20220912135742.11764-9-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Scan the target devices during system resume time and add or remove the
target device with the SML if the corresponding target device is newly
added or removed respectively.
Link: https://lore.kernel.org/r/20220912135742.11764-8-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Free the enclosure device objects during driver unload and before
rescanning the target devices during controller reset.
Link: https://lore.kernel.org/r/20220912135742.11764-7-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement graceful handling of surprise or orderly removal of PCIe HBA:
- Detect a hot removal of the controller at certain critical places in the
driver. Early detection will help to reduce the time taken for cleaning
up the hot-removed controller at the driver level.
- Poll the status of the port enable issued after reset once every 5
seconds to avoid a long delay in detecting unavailable controller.
Link: https://lore.kernel.org/r/20220912135742.11764-5-sreekanth.reddy@broadcom.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the host's SAS ports if there is change in port id or phys. If the
port id is changed, then the driver updates it. If some phys are
enabled/disabled during reset, then driver updates them in STL.
Check for the responding expander devices and update the device handle if
it got changed. Register the expander with STL if it got added during reset
and unregister the expander device if it got removed during reset.
[mkp: include fix for zeroday warning]
Link: https://lore.kernel.org/r/20220804131226.16653-15-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for the following SAS transport class callbacks:
- get_linkerrors
- get_enclosure_identifier
- get_bay_identifier
- phy_reset
- phy_enable
- set_phy_speed
- smp_handler
Link: https://lore.kernel.org/r/20220804131226.16653-14-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add framework to issue MPT transport commands to controllers. Also issue
the MPT transport commands to get the manufacturing info of SAS expander
device.
Link: https://lore.kernel.org/r/20220804131226.16653-13-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Register/unregister the SAS, SATA devices to SCSI Transport Layer(STL)
whenever the corresponding device is added/removed from topology.
Link: https://lore.kernel.org/r/20220804131226.16653-12-sreekanth.reddy@broadcom.com
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When device is registered with the STL then get the corresponding device's
target object using the rphy in below callback functions:
- mpi3mr_target_alloc()
- mpi3mr_slave_alloc()
- mpi3mr_slave_configure()
- mpi3mr_slave_destroy()
Link: https://lore.kernel.org/r/20220804131226.16653-11-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Register/unregister the expander devices to SCSI Transport Layer(STL)
whenever the corresponding expander is added/removed from topology.
Link: https://lore.kernel.org/r/20220804131226.16653-10-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Register the SAS, SATA devices to SCSI Transport Layer (STL) only if
multipath capability is disabled in the controller's firmware.
Link: https://lore.kernel.org/r/20220804131226.16653-9-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the following helper functions:
- Update the host phys with STL
- Remove the device's SAS port with STL
Link: https://lore.kernel.org/r/20220804131226.16653-8-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the following helper functions:
- Get the device's sas address by reading corresponding device's Device
page0
- Get the expander object from expander list based on expander's handle
- Get the target device object from target device list based on device's
sas address
- Get the expander device object from expander list based on expanders's
sas address
- Get hba port object from hba port table list based on port's port id
Link: https://lore.kernel.org/r/20220804131226.16653-7-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add framework to register and unregister the host and expander phys with
SCSI Transport Layer (STL).
Link: https://lore.kernel.org/r/20220804131226.16653-6-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable and process the Enclosure device add event.
Link: https://lore.kernel.org/r/20220804131226.16653-5-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add helper functions to retrieve below controller's config pages:
- SAS IOUnit Page0
- SAS IOUnit Page1
- Driver Page1
- Device Page0
- SAS Phy Page0
- SAS Phy Page1
- SAS Expander Page0
- SAS Expander Page1
- Enclosure Page0
Also add the helper function to set SAS IOUnit Page1.
Link: https://lore.kernel.org/r/20220804131226.16653-4-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reduce the VD queue depth on detecting the throttling condition.
[mkp: incorporate fix for pointer cast issue reported by the test
robot and Guenter Roeck]
Link: https://lore.kernel.org/r/20220708195020.8323-3-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update driver to track cumulative pending large data size at the controller
level and at the throttle group level. When one of the values meet or
exceed the controller's firmware-determined high threshold value, then the
driver will divert future selective I/O to the firmware. Once both
controller level and at the throttle group level cumulative pending large
data size reach controller's firmware determined low threshold value, then
the driver will stop diverting I/Os to the firmware.
Link: https://lore.kernel.org/r/20220708195020.8323-2-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During driver unload, mrioc->bsg_device reference count becomes
negative. Also, as reported in [1], the driver's bsg_device model had few
more bugs. Fix all these up.
[1] https://marc.info/?l=linux-scsi&m=165183971411991&w=2
Link: https://lore.kernel.org/r/20220526170157.58274-1-sumit.saxena@broadcom.com
Fixes: 4268fa7513 ("scsi: mpi3mr: Add bsg device support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add sysfs attributes for exposing target device details such as SAS
address, firmware device handle, and persistent ID for the
controller-attached devices and RAID volumes.
Link: https://lore.kernel.org/r/20220517115310.13062-3-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for management applications to send an MPI3 Encapsulated NVMe
passthru command to the NVMe devices attached to an Avenger controller.
Since the NVMe drives are exposed as SCSI devices by the controller, the
standard NVMe applications cannot be used to interact with the drives and
the command sets supported are also limited by the controller firmware.
Special handling is required for MPI3 Encapsulated NVMe passthru commands
for PRP/SGL setup in the commands.
Link: https://lore.kernel.org/r/20220429211641.642010-8-sumit.saxena@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
