CPU temperature can be negative in some cases. Thus the negative CPU
temperature should not be considered as a failure.
Fix intel_tcc_get_temp() and its users to support negative CPU
temperature.
Fixes: a3c1f066e1 ("thermal/intel: Introduce Intel TCC library")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Cc: 6.3+ <stable@vger.kernel.org> # 6.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When the hardware reduces the power to the minimum possible, the power
floor is notified via an interrupt.
This can happen when user space requests a power limit via powercap RAPL
interface, which forces the system to enter to the lowest power. This
power floor indication can be used as a hint to resort to other methods
of reducing power than via RAPL power limit.
Before power floor status can be read or the firmware can trigger
notifications regarding it, it needs to be configured via a mailbox
command. The actual power floor status is read via bit 39 of MMIO
offset 0x5B18 of the processor thermal PCI device.
To show the current power floor status and get notification
on a sysfs attribute, add 2 new attributes to
/sys/bus/pci/devices/0000\:00\:04.0/power_limits/
power_floor_enable : This attribute is present when power floor
notifications are supported. This attribute allows to enable/disable
power floor notifications.
power_floor_status : This attribute is present when power floor
notifications are supported. When enabled via power_floor_enable, this
attribute shows the current power floor status.
The power floor implementation provides interfaces which are called
from the sysfs callbacks to enable/disable and read power floor
status. It also provides two additional interfaces to check if the
current processor thermal device interrupt is for power floor status
and to send notifications to user space.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog and documentation changes edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Prior to Meteor Lake processor generation, user space can pass workload
type request to the firmware. Then firmware can optimize power based on
the indicated workload type. User space also uses workload type requests
to implement its own heuristics.
The firmware in Meteor Lake processor generation is capable of predicting
workload type without software help.
To avoid duplicate processing, add a sysfs interface allowing user space
to obtain the workload hint from the firmware instead of trying to
predict the workload type by itself.
This workload hint is passed from the firmware via MMIO offset 0x5B18 of
the processor thermal PCI device. Before workload hints can be produced by
the firmware, it needs to be configured via a mailbox command. This
mailbox command turns ON the workload hint and it allows to program a
notification delay to control the rate of notifications.
The notification delay can be changed from user space vis sysfs.
Attribute group 'workload_hint' in sysfs is used for implementing the
workload hints interface between user space and the kernel.
It contains the following attributes:
workload_type_enable:
Enables/disables workload type hints from the firmware.
notification_delay_ms:
Notification delay in milliseconds.
workload_type_index:
The current workload type index predicted by the firmware (see
the documentation changes below for supported index values and
their meaning).
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog edits, documentation edits, whitespace adjustments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The processor thermal mailbox is used for workload type request and
also in the processor thermal RFIM module. So, move the workload type
request code to its own module from the current processor thermal
mailbox module.
processor_thermal_mailbox.c contains only mailbox read/write related
source code. The source related to workload_types requests is moved to
a module processor_thermal_wt_req.c.
In addition
- Rename PROC_THERMAL_FEATURE_MBOX to PROC_THERMAL_FEATURE_WT_REQ.
- proc_thermal_mbox_add(), which adds workload type sysfs attribute group
is renamed to proc_thermal_wt_req_add().
- proc_thermal_mbox_remove() is renamed to proc_thermal_wt_req_remove().
While here, resolve check patch warnings for 100 columns for only modified
lines.
No functional changes are expected.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for DLVR (Digital Linear Voltage Regulator) attributes,
which can be used to control RFIM.
Here instead of "fivr" another directory "dlvr" is created with DLVR
attributes:
/sys/bus/pci/devices/0000:00:04.0/dlvr
├── dlvr_freq_mhz
├── dlvr_freq_select
├── dlvr_hardware_rev
├── dlvr_pll_busy
├── dlvr_rfim_enable
└── dlvr_spread_spectrum_pct
└── dlvr_control_mode
└── dlvr_control_lock
Attributes
dlvr_freq_mhz (RO):
Current DLVR PLL frequency in MHz.
dlvr_freq_select (RW):
Sets DLVR PLL clock frequency.
dlvr_hardware_rev (RO):
DLVR hardware revision.
dlvr_pll_busy (RO):
PLL can't accept frequency change when set.
dlvr_rfim_enable (RW):
0: Disable RF frequency hopping, 1: Enable RF frequency hopping.
dlvr_control_mode (RW):
Specifies how frequencies are spread. 0: Down spread, 1: Spread in Center.
dlvr_control_lock (RW):
1: future writes are ignored.
dlvr_spread_spectrum_pct (RW)
A write to this register updates the DLVR spread spectrum percent value.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* thermal: (734 commits)
thermal: core: call put_device() only after device_register() fails
Linux 6.2-rc4
kbuild: Fix CFI hash randomization with KASAN
firmware: coreboot: Check size of table entry and use flex-array
kallsyms: Fix scheduling with interrupts disabled in self-test
ata: pata_cs5535: Don't build on UML
lockref: stop doing cpu_relax in the cmpxchg loop
x86/pci: Treat EfiMemoryMappedIO as reservation of ECAM space
efi: tpm: Avoid READ_ONCE() for accessing the event log
io_uring: lock overflowing for IOPOLL
ALSA: pcm: Move rwsem lock inside snd_ctl_elem_read to prevent UAF
iommu/mediatek-v1: Fix an error handling path in mtk_iommu_v1_probe()
iommu/iova: Fix alloc iova overflows issue
iommu: Fix refcount leak in iommu_device_claim_dma_owner
iommu/arm-smmu-v3: Don't unregister on shutdown
iommu/arm-smmu: Don't unregister on shutdown
iommu/arm-smmu: Report IOMMU_CAP_CACHE_COHERENCY even betterer
platform/x86: thinkpad_acpi: Fix profile mode display in AMT mode
ALSA: usb-audio: Fix possible NULL pointer dereference in snd_usb_pcm_has_fixed_rate()
platform/x86: int3472/discrete: Ensure the clk/power enable pins are in output mode
...
In the process of replacing the get_trip_* ops by the generic trip
points, the current code has an 'override' property to add another
indirection to a different ops.
Rework this approach to prevent this indirection and make the code
ready for the generic trip points conversion.
Actually the get_temp() is different regarding the platform, so it is
pointless to add a new set of ops but just create dynamically the ops
at init time.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20221003092602.1323944-29-daniel.lezcano@linaro.org
Cleanup the code by using Intel TCC library for TCC (Thermal Control
Circuitry) MSR access.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When the driver resumes, the tcc offset is set back to its previous
value. But this only works if the value was user defined as otherwise
the offset isn't saved. This asymmetric logic is harder to maintain and
introduced some issues.
Improve the logic by saving the tcc offset in a suspend op, so the right
value is always restored after a resume.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pI andruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210909085613.5577-3-atenart@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
After upgrading to Linux 5.13.3 I noticed my laptop would shutdown due
to overheat (when it should not). It turned out this was due to commit
fe6a6de669 ("thermal/drivers/int340x/processor_thermal: Fix tcc setting").
What happens is this drivers uses a global variable to keep track of the
tcc offset (tcc_offset_save) and uses it on resume. The issue is this
variable is initialized to 0, but is only set in
tcc_offset_degree_celsius_store, i.e. when the tcc offset is explicitly
set by userspace. If that does not happen, the resume path will set the
offset to 0 (in my case the h/w default being 3, the offset would become
too low after a suspend/resume cycle).
The issue did not arise before commit fe6a6de669, as the function
setting the offset would return if the offset was 0. This is no longer
the case (rightfully).
Fix this by not applying the offset if it wasn't saved before, reverting
back to the old logic. A better approach will come later, but this will
be easier to apply to stable kernels.
The logic to restore the offset after a resume was there long before
commit fe6a6de669, but as a value of 0 was considered invalid I'm
referencing the commit that made the issue possible in the Fixes tag
instead.
Fixes: fe6a6de669 ("thermal/drivers/int340x/processor_thermal: Fix tcc setting")
Cc: stable@vger.kernel.org
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pI andruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210909085613.5577-2-atenart@kernel.org
The following fixes are done for tcc sysfs interface:
- TCC is 6 bits only from bit 29-24
- TCC of 0 is valid
- When BIT(31) is set, this register is read only
- Check for invalid tcc value
- Error for negative values
Fixes: fdf4f2fb8e ("drivers: thermal: processor_thermal_device: Export sysfs interface for TCC offset")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: stable@vger.kernel.org
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210628215803.75038-1-srinivas.pandruvada@linux.intel.com
Remove enumeration part from the processor_thermal_device to two
different modules. One for ACPI and one for PCI:
ACPI enumeration: int3401_thermal
PCI part: processor_thermal_device_pci_legacy
The current processor_thermal_device now just implements interface
functions to be used by the ACPI and PCI enumeration module. This is
done by:
1. Make functions proc_thermal_add() and proc_thermal_remove() non static
and export them for usage in other processor_thermal_device_pci_legacy.c
and in int3401_thermal.c.
2. Move the sysfs file creation for TCC offset and power limit attribute
group to the proc_thermal_add() from the individual enumeration callbacks
for PCI and ACPI.
3. Create new interface functions proc_thermal_mmio_add() and
proc_thermal_mmio_remove() which will be called from the
processor_thermal_device_pci_legacy module.
4. Export proc_thermal_resume(), so that it can be used by power
management callbacks.
5. Remove special check for double enumeration as it never happens.
While here, fix some cleanup on error conditions in proc_thermal_add().
No functional changes are expected with this change.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210525204811.3793651-2-srinivas.pandruvada@linux.intel.com
Added processor thermal device mail box interface for workload hints
setting. These hints will give indication to hardware to better manage
power and thermals. The supported hints are:
idle
semi_active
burusty
sustained
battery_life
For example when the system is on battery, the hardware can be less
aggressive in power ramp up.
This will create an attribute group at
/sys/bus/pci/devices/0000:00:04.0/workload_request
This folder contains two attributes:
workload_available_types : (RO): This shows available workload types
workload_type: (RW) : Allows to set and get current workload type
setting
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-4-srinivas.pandruvada@linux.intel.com
Add support for RFIM (Radio Frequency Interference Mitigation) support
via processor thermal PCI device. This drivers allows adjustment of
FIVR (Fully Integrated Voltage Regulator) and DDR (Double Data Rate)
frequencies to avoid RF interference with WiFi and 5G.
Switching voltage regulators (VR) generate radiated EMI or RFI at the
fundamental frequency and its harmonics. Some harmonics may interfere
with very sensitive wireless receivers such as Wi-Fi and cellular that
are integrated into host systems like notebook PCs. One of mitigation
methods is requesting SOC integrated VR (IVR) switching frequency to a
small % and shift away the switching noise harmonic interference from
radio channels. OEM or ODMs can use the driver to control SOC IVR
operation within the range where it does not impact IVR performance.
DRAM devices of DDR IO interface and their power plane can generate EMI
at the data rates. Similar to IVR control mechanism, Intel offers a
mechanism by which DDR data rates can be changed if several conditions
are met: there is strong RFI interference because of DDR; CPU power
management has no other restriction in changing DDR data rates;
PC ODMs enable this feature (real time DDR RFI Mitigation referred to as
DDR-RFIM) for Wi-Fi from BIOS.
This change exports two folders under /sys/bus/pci/devices/0000:00:04.0.
One folder "fivr" contains all attributes exposed for controling FIVR
features. The other folder "dvfs" contains all attributes for DDR
features.
Changes done to implement:
- New module for rfim interfaces
- Two new per processor features for DDR and FIVR
- Enable feature for Tiger Lake (FIVR only) and Alder Lake
The attributes exposed and explanation:
FIVR attributes
vco_ref_code_lo (RW): The VCO reference code is an 11-bit field and
controls the FIVR switching frequency. This is the 3-bit LSB field.
vco_ref_code_hi (RW): The VCO reference code is an 11-bit field and
controls the FIVR switching frequency. This is the 8-bit MSB field.
spread_spectrum_pct (RW): Set the FIVR spread spectrum clocking
percentage
spread_spectrum_clk_enable (RW): Enable/disable of the FIVR spread
spectrum clocking feature
rfi_vco_ref_code (RW): This field is a read only status register which
reflects the current FIVR switching frequency
fivr_fffc_rev (RW): This field indicated the revision of the FIVR HW.
DVFS attributes
rfi_restriction_run_busy (RW): Request the restriction of specific DDR
data rate and set this value 1. Self reset to 0 after operation.
rfi_restriction_err_code (RW): Values: 0 :Request is accepted, 1:Feature
disabled, 2: the request restricts more points than it is allowed
rfi_restriction_data_rate_Delta (RW): Restricted DDR data rate for RFI
protection: Lower Limit
rfi_restriction_data_rate_Base (RW): Restricted DDR data rate for RFI
protection: Upper Limit
ddr_data_rate_point_0 (RO): DDR data rate selection 1st point
ddr_data_rate_point_1 (RO): DDR data rate selection 2nd point
ddr_data_rate_point_2 (RO): DDR data rate selection 3rd point
ddr_data_rate_point_3 (RO): DDR data rate selection 4th point
rfi_disable (RW): Disable DDR rate change feature
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-3-srinivas.pandruvada@linux.intel.com
Added AlderLake PCI device id to support processor thermal driver. Reuse
the feature set (just includes RAPL) from previous generations.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-2-srinivas.pandruvada@linux.intel.com
The Processor Thermal PCI device supports multiple features. Currently
we export only RAPL. But we need more features from this device exposed
for Tiger Lake and Alder Lake based platforms. So re-structure the
current MMIO interface, so that more features can be added cleanly.
No functional changes are expected with this change.
Changes done in this patch:
- Using PCI_DEVICE_DATA(), hence names of defines changed
- Move RAPL MMIO code to its own module
- Move the RAPL MMIO offsets to RAPL MMIO module
- Adjust Kconfig dependency of PROC_THERMAL_MMIO_RAPL
- Per processor driver data now contains the supported features
- Moved all the common data structures and defines to a common header
file
- This new header file contains all the processor_thermal_* interfaces
- Based on the features supported the module interface is called
- Each module atleast provides one add and one remove function
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-1-srinivas.pandruvada@linux.intel.com
Update PCI device id for Jasper Lake processor thermal device.
With this proc_thermal driver is getting loaded and processor
thermal functionality works on Jasper Lake system.
Fixes: f64a6583d3 ("thermal: int340x: processor_thermal: Add Jasper Lake support")
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1595577146-1221-1-git-send-email-sumeet.r.pawnikar@intel.com
Add new PCI id for Ice lake processor thermal device. Also enabled
the RAPL mmio interface. The MMIO offsets match Skylake.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This change exports an interface to read tcc offset and allow writing if
the platform is not locked.
Refer to Intel SDM for details on the MSR: MSR_TEMPERATURE_TARGET.
Here TCC Activation Offset (R/W) bits allow temperature offset in degrees
in relation to TjMAX.
This change will be useful for improving performance from user space for
some platforms, if the current offset is not optimal.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Benjamin Berg <bberg@redhat.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Passing 0 to cpuhp_remove_state() triggers the BUG_ON() in
__cpuhp_remove_state_cpuslocked() and the argument passed to
powercap_unregister_control_type() is expected to be a valid
pointer, so avoid calling these functions with incorrect
arguments from proc_thermal_rapl_remove().
Fixes: 555c45fe0d ("int340X/processor_thermal_device: add support for MMIO RAPL")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
- Add MMIO interface support to the Intel RAPL power capping
driver and update the int340X thermal driver to provide a
RAPL MMIO interface (Zhang Rui, Stephen Rothwell).
- Add Intel Ice Lake CPU IDs to the RAPL driver (Zhang Rui,
Rajneesh Bhardwaj).
- Make cpufreq use the PM QoS framework (instead of notifiers) for
managing the min and max frequency constraints (Viresh Kumar).
- Add i.MX8MN support to the imx-cpufreq-dt cpufreq driver (Anson
Huang).
-----BEGIN PGP SIGNATURE-----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=Svee
-----END PGP SIGNATURE-----
Merge tag 'pm-5.3-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These modify the Intel RAPL driver to allow it to use an MMIO
interface to the hardware, make the int340X thermal driver provide
such an interface for it, add Intel Ice Lake CPU IDs to the RAPL
driver (these changes depend on the previously merged x86 arch
changes), update cpufreq to use the PM QoS framework for managing the
min and max frequency limits, and add update the imx-cpufreq-dt
cpufreq driver to support i.MX8MN.
Specifics:
- Add MMIO interface support to the Intel RAPL power capping driver
and update the int340X thermal driver to provide a RAPL MMIO
interface (Zhang Rui, Stephen Rothwell).
- Add Intel Ice Lake CPU IDs to the RAPL driver (Zhang Rui, Rajneesh
Bhardwaj).
- Make cpufreq use the PM QoS framework (instead of notifiers) for
managing the min and max frequency constraints (Viresh Kumar).
- Add i.MX8MN support to the imx-cpufreq-dt cpufreq driver (Anson
Huang)"
* tag 'pm-5.3-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (27 commits)
cpufreq: Make cpufreq_generic_init() return void
intel_rapl: need linux/cpuhotplug.h for enum cpuhp_state
powercap/rapl: Add Ice Lake NNPI support to RAPL driver
powercap/intel_rapl: add support for ICX-D
powercap/intel_rapl: add support for ICX
powercap/intel_rapl: add support for IceLake desktop
intel_rapl: Fix module autoloading issue
int340X/processor_thermal_device: add support for MMIO RAPL
intel_rapl: support two power limits for every RAPL domain
intel_rapl: support 64 bit register
intel_rapl: abstract RAPL common code
intel_rapl: cleanup hardcoded MSR access
intel_rapl: cleanup some functions
intel_rapl: abstract register access operations
intel_rapl: abstract register address
intel_rapl: introduce struct rapl_if_private
intel_rapl: introduce intel_rapl.h
intel_rapl: remove hardcoded register index
intel_rapl: use reg instead of msr
cpufreq: imx-cpufreq-dt: Add i.MX8MN support
...
Introduce MMIO RAPL support as Intel processor_thermal device exposes the
capability to do RAPL control via MMIO registers.
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@intel.com>
Tested-by: Pandruvada, Srinivas <srinivas.pandruvada@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As a system sleep callback, proc_thermal_resume() should be defined only
if CONFIG_PM_SLEEP is defined.
This fixes a build warning when CONFIG_PM_SLEEP is not set,
drivers/thermal/intel/int340x_thermal/processor_thermal_device.c:446:12: error: 'proc_thermal_resume' defined but not used [-Werror=unused-function]
static int proc_thermal_resume(struct device *dev)
Fixes: aaba9791fb ("drivers: thermal: processor_thermal: Read PPCC on resume")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Read PPCC power limits on system resume in case those limits changed
while system was suspended.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Downgrade "Unsupported event" message from dev_err to dev_dbg. Otherwise it
floods with this message one some platforms.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This simplifies getting the 'driver_data' from 'struct device' directly.
Going through platform_device or pci_dev is not required. Also removes
condition check as the private data stored with dev pointer, means
irrespective of enumeration mode, we can use dev_get_drvdata().
This removes the unnecessary step back and forth.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Changes since V1:
* Use dev_info instead of printk
* Use dev_warn instead of BUG_ON
Previously, sysfs_create_group was called before all initialization had
fully run - specifically, before pci_set_drvdata was called. Since the
sysctl group is visible to userspace as soon as sysfs_create_group
returns, a small window of time existed during which a process could read
from an uninitialized/partially-initialized device.
This commit moves the creation of the sysctl group to after all
initialized is completed. This ensures that it's impossible for
userspace to read from a sysctl file before initialization has fully
completed.
To catch any future regressions, I've added a check to ensure
that proc_thermal_emum_mode is never PROC_THERMAL_NONE when a process
tries to read from a sysctl file. Previously, the aforementioned race
condition could result in the 'else' branch
running while PROC_THERMAL_NONE was set,
leading to a null pointer deference.
Signed-off-by: Aaron Hill <aa1ronham@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This cleans up the directory a bit, now that we have several other
platforms using platform-specific sub-directories. Compile-tested with
ARCH=x86 defconfig and the drivers explicitly enabled with menuconfig.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2018-12-07 16:48:47 +08:00
Renamed from drivers/thermal/int340x_thermal/processor_thermal_device.c (Browse further)
